Channel Vision 6565 User manual

6565
Dome Color Megapixel IP Camera w/IR Illuminators
• Intelligent Entertainment • Infrastructure • Security Solutions

Table Of Contents
Model Info.................................................................................... Page 3
Safety Warnings.......................................................................... Page 4
I /O Pin-Out............................................ .............. Page 5
Camera Mounting....................................................................... Page 6
Assigning An IP Address continued......................................... Page 7
Assigning An IP Address continued......................................... Page 8
Assigning An IP Address continued......................................... Page 9 & 10
Connecting Your Camera........................................................... Page 11
Installing The ActiveX Control................................................... Page 11
Configuring Internet Explorer.................................................... Page 12
Live Viewing................................................................................. Page 13
Live Viewing continued.............................................................. Page 14
Configuration............................................................................... Page 15
System Configuration................................................................. Page 16
User Management....................................................................... Page 17
System Update............................................................................ Page 18
Network........................................................................................ Page 19
Network continued...................................................................... Page 20
Network continued...................................................................... Page 21
Network continued...................................................................... Page 22
Factory Default.............................................................................Page 23
Video Settings............................................................................. Page 24
Video Settings continued........................................................... Page 25
Video Settings continued........................................................... Page 26
Video Settings continued........................................................... Page 27
Video Settings continued........................................................... Page 28
Video Settings continued........................................................... Page 29
Recommended Video Settings................................................... Page 30
Recommended Video Settings/Cont.......................................... Page 31
Audio............................................................................................ Page 32
Audio continued.......................................................................... Page 33
Event List..................................................................................... Page 34
Event List Continued.................................................................. Page 35
Schedule...................................................................................... Page 36
I/O Settings.................................................................................. Page 37
............................................................... Page 38
SD Card Page 39
........................
I/O Settings Continued
........................................................................................
Port Forwarding.......................................................................... Page 40
Specifications............................................................................. Page 41
Warranty Statement..................................................................... Page 42
2

The 6565 is a 2 Megapixel dome IP camera.
Built-in web server allows users to view high quality, real-time video with Internet Explorer browser.
Uses H.264, MJPEG and MPEG4 codecs
Live video can be recorded to a computer and played back remotely, as well as viewed from many
mobile phones and other devices.
Designed for large commercial projects with 100’s of cameras or a single family house requiring a
camera at the front door.
6565 Features:
Channel Vision’s 6565 Vandal Proof IP Dome offers superior image quality with a 2 megapixel CMOS
sensor and has the ability to capture images up to 1080p (1920 x 1080 pixels).
With H.264 compression, less bandwidth and storage space are used, while delivering full resolution at
max frame rate with faster speeds over the internet.
The 6564 also features event triggered SD card recording, as well as 18 IR LED for a viewing distance
of 50 feet in total darkness. Monitoring can be done anywhere an internet connection is available even
from a 3G Smart-phone
Models 6565
3

4
Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions for future reference.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with a dry cloth.
6. Install in accordance with these instructions.
7 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
that produce heat.
8. Do not defeat the safety purpose of the polarized-type plug. A polarized plug has two blades with
one wider than the other. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete
outlet.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point of exit from the apparatus.
10. Only use attachments/accessories specified by Channel Vision.
11. Unplug this apparatus during lightning storms or when unused for long periods of time.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the inside of the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
13. The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the
user to presence of uninsulated dangerous voltage within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
14. The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance accompanying the appliance.
15. Inside of apparatus shall not be exposed to dripping or splashing and objects filled with liquids.
CAUTION: To reduce the risk of electric shock,
do not remove the cover (or back). There are no
user-serviceable parts inside, refer servicing to
qualified service personnel.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN !

1. Digital Input (D1 + Ground):
An alarm input for connecting devices that can toggle between an open and closed circuit, for example PIRs,
door/window contacts, broken glass detectors, etc. When a signal is received, the state changes and the input
becomes active.
2. Relay Output (Ground + DO)
A selectable output for a relay switch, for example LEDs, Sirens, etc.
Normally Open and Normally Closed can be selected via the Internet Explorer ActiveX control under the “I/O
Setting” section on the left. (See pages 35, 36 for I/O settings)
3. Audio Output ( Ground)
An audio output that can be fed into an amplifier
4. Audio Input (Mic In + Ground)
A microphone input that can be used with a standard line level microphone, such as the 5104-Mic.
5. Video Out (Video Out + Ground)
Composite video output, used to adjust the camera. Note: if you do not have network connected, this output will
automatically shut off within 24 hours.
Audio Out
I/O Pin Out
5
PoE (Power Over Ethernet)
Power over Ethernet (PoE) is a technology that integrates power into a standard LAN infrastructure. It enables
power to be provided to the network device, such as an IP phone or a network camera, using the same cable
that is used for the network connection. The PoE switch eliminates the need for power outlets at the camera
locations and enables an easier application of uninterruptible power supplies (UPS) to ensure 24 hours a day, 7
days a week operation. A 802.3af, 15.4W PoE Switch is recommended with 6565.
If using a PoE switch that does not meet this specification, full functionality may not be supported.

6
Camera Mounting
Before you close the dome cover, verify the black rubber gasket is stuck to the inside of the cover completely. If the
gasket is uneven, the camera may not be fully waterproof. Tighten all 4 screws on the dome cover to ensure that
there is no gap between the lid and base of the camera.
Apply a thin coat of silicon around the gap once the camera is assembled to increase water resistance.
Mount the bottom of the camera housing on a smooth, flat surface. When you mount the camera on a ceiling or
wall, use the screws with the rubber o-rings. Without the o-ring, water may get into the camera.

1. Use the software, “IP Installer” to assign the IP address to your IP Camera You can find "IP
Installer" in the supplied CD.
2. Execute IP Installer. This is located on your disk under the folder “Megapixel Camera
Network Search Application”
3. If Windows prompts you to unblock IP Installer, you must select “unblock”
There are 3 kinds of IP configuration
A. Fixed IP (Public IP or Virtual IP)
B. DHCP (Dynamic IP)
C. Dial-up/DSL (PPPoE)
"IP Installer" will search all IP Cameras connected to your LAN network.The user can
click “Search Device” to search again.
Assigning an IP Address
7

1. Click the start icon on your computer
2. Click the ‘Run’ icon on your computer.
3. Type in ‘cmd’ and press enter on your keyboard, or press ok.
4. Type in ‘ipconfig /all’ into the DOS prompt that appears. Press enter.
5. Write down your computer’s IP address.
It is important that we do not use the same IP address for our IP Camera.
In the example below, the computer’s IP address is 192.168.1.74.
The IP address of the IP Camera must be different than the IP address in the computer.
Each networkable device in your network has an IP address assigned. You need to be sure the IP you
choose for your IP camera is not the same as any other device on your network.
Assigning an IP Address /cont
8

Assigning an IP Address /cont
6. Copy/write down the following information from the DOS prompt.
A. Default Gateway (Example 192.168.1.1)
B. DNS Server (if 2 servers, use the first one, for example 192.168.1.9)
C. Subnet Mask (Example 255.255.255.0)
9

Assigning an IP Address /cont
To change numbers, select the appropriate area on IP installer
with your mouse, and type in the info.
Name
Fourth number (different than computer)
Select “Static”
Subnet Mask (same as computer)
Default Gateway (same as computer)
DNS Server 1 (same as computer)
DNS Server 2 (same as computer)
Port (A port between 8000-8999 is
recommended, but any network
port can be used)
First 3 numbers are
same as computer
7. Enter the information you wrote down from step 6 on page 9 into the IP camera network page
A. Default Gateway (Enter this number under “Gateway”)
B. DNS Server (Enter this number under “DNS 1”)
C. Subnet Mask (Enter this number under “Netmask”)
8. Giving the IP Camera a unique IP address.
Assign an IP address to the IP Camera by using the first 3 sets of numbers of your default gateway. A IP
address, has 4 sets of numbers, each followed by a period. For example, xxx.xxx.xxx.xxx My default
gateway is 192.168.1.1 So, for example, my IP Camera’s address will start with 192.168.1.xxx
9. Make sure you use a number different that your computer’s IP address.
(Generally between 2-250) This number needs to be out of the range of DHCP. DHCP is assigned with
your router, and can be checked by logging into the router.
My computer’s IP address is 192.168.1.74. I have used 192.168.1.208 for my IP Camera.
You must choose a number that is different from your computer’s IP.
If your IT technician has designated a static internal IP for your IP Camera, use that address.
10. To assign the port, choose a port between 5400-9000, and type it into “Port 1” If a specific port has
been designated for your security system, that can also be used, even if the number is not within the
range of 5400-9000.
10
*Disclaimer: This is an example based on a general network setup.
All networks do not match these settings exactly, as all networks are different

Connecting To Your Camera
1. The first time you connect to the camera via Internet Explorer, it will ask you to install the
ActiveX control. Internet Explorer 6, 7, 8, or 9 must be used to run this ActiveX control.
1. Open Internet Explorer. Type the IP address of the IP camera into the browser link window.
Also, make sure to type the port at the end of the link.
For example, I will type in http://192.168.1.207:8005
2. You will be prompted for a username and password.
The default username is ‘admin’
The default password is ‘admin’
Installing The ActiveX Control
11

When the following dialogue box , click “Yes”. pops up
If the installation of the ActiveX control fails, for example the browser page says “done” but
you do not see your camera, please check the security settings for your IE browser. Follow
the instructions below.
Configuring Internet Explorer
Step 1 Step 2
Step 3 Step 4
Step 5
12

Live Viewing
Snapshot
Format: Year/Month/Day/Hour/Minute/Second/ Image Size/Frames Per Second
Controls the physical size of the streaming video on the browser screen
Controls the selection of the video
stream that is being viewed
Activates 2-way audio
Activates relay output
Shows the number of users
connected at any given time
Settings
Once you connect to your camera, you will see the following screen.
Below the icons and their functionality are defined.
13

1. Th
2. This icon takes a snapshot
3. This icon shows system time, video resolution, and video refreshing rate
4. The bottom bar has an icon that allows you to select which stream
you want to view. Stream 1 is usually the larger, better quality stream.
Stream 2 is the smaller stream, generally used for mobile viewing
5. These cameras support 2 way audio.
The bottom bar has an icon that will will activate 2 way audio
For 2 way audio to function, you will need a microphone plugged into the computer.
6. The bottom bar has an icon shows how many users are connected
to the IP camera.
7. This icon will control/activate the relay output on the camera
wire pigtail. A relay can activate lights, alarms, or anything that uses a contact
closure.
8. If you double click the video feed, it will make the video full screen.
To change video back to normal mode, press ‘Escape’ on your keyboard, or double
click anywhere in the video feed a second time.
9. If you right click on the video, you have access to several different functions.
A. Snapshot: Takes a snapshot
B. Record Start : Records video to your computer
F. Frame BuffmSec: This changes the frame buffer rate
Digital zoom
1. Select “Enable digital zoom”
2. Select the area of the screen you wish to zoom in on
3. Select the zoom level
is icon opens the settings menu
Live Viewing/cont.
1
3
2
C. Mute: Mutes 2 way audio, if activated
D. Full Screen: Makes the IP camera full screen
E. Zoom: Digital zoom. This is explained below
14

Configuration
1. Select this icon to enter the settings menu
2. Select this icon to go back to your live video feed
1
2
15

System Configuration
1
3
2
4
8
10
12
9
11
13
14
15
16
5
6
7
System Information:
Use the number scheme below for a description of each item:
1. MAC Address: (Media Access Control) address; This is a unique identifier assigned to IP devices for
communication with the network. Your IP camera is pre-set with a MAC address
2. Server name: Select to edit the camera name
3. LED Indicator: Select On/Off to toggle the blinking LED light in the camera
4. Language: Select a language to change the language of the ActiveX interface
5. Status Bar: Select On/Off to toggle the information bar (below the main video stream)
6. Time Stamp: Select Enabled/Disabled to turn the video timestamp on or off
7. Text: Select Enabled/Disabled to specify the name that can be displayed on the top left area of the screen
8. Server Time: This shows the current time on your IP camera
9. Date Format: Select to choose your desired date format
10. Time Zone: This shows your current time zone
11. NTP: The Network Time Protocol is a protocol for synchronizing the clocks of computer systems
12. NTP Server: If you have a NTP server, input it here
13. Update: If using an NTP server, select this drop down menu to choose the update interval
14. Time Shift: Time shift is used to compensate for the time it takes to server to process the sync request for your
time. This is usually not needed.
15. Synchronize with PC’s time: Select this to match your computer’s clock to your IP camera
16. Apply: Select this button to save your changes
16

User managment:
This IP camera supports 3 different types of users.
1. Administrator
2. General
3. Anonymous
Click “Yes” to allow anonymous user access
Click “Add/Set” to add a user
Click “Edit” to modify a user.
When you click edit, the following window will pop up:
(Shown below.)
Add the username and password, and click “OK” to save your new user.
User Management
17

System Update
System Update: This menu is used to perform the following functions:
1. Firmware Update: Channel Vision will update the firmware from time to time.
By registering your IP camera, you have access to all firmware improvements
and extended warranty options. How? See the product page on www.channelvision.com
To load new firmware, press “Browse” and select the firmware.bin file.
2. Restart System: Select to restart system.
You can reset the IP camera to factory default settings if desired
If you backup your settings, you can load your backup file where
it says “New Setting File”
3. Settings backup:
You can backup your settings by right clicking your
mouse on “Setting Download” and selecting
“Save Target As”. You may also load previously saved
settings files this way. When loading previously saved files,
click “Browse” and then “Upgrade”
18

Network Setup/IP Setting: This setting is for the external viewing of camera over the internet.
Once set up, you will be able to view this camera from anywhere in the world.
This IP camera supports DHCP and Static settings.
If you are new to installing an IP camera, use #2 (Static IP)
1. DHCP: If you use this setting, your IP information will be pulled automatically from
your router. This not recommended if you are going to view this camera outside of
the building that it resides in.
2. Static IP: This is an IP that you manually set. This IP must not be the same as
any other device within your network. You must also set default gateway, DNS server,
subnet mask, and DNS server. Please refer to page 6 & 7 for instructions
on how to obtain these numbers.
3. Port Assignment: You can assign different ports for your camera.
(Explained below.)
A. Web Page Port: (This is the port that 99% of installations will use)
A web page port is used to transmit data out of your network. For example,
If my external IP address is http://67.88.12.50, and my port was 5400,
I would put a “:” and the port. The final address would be http://67.88.12.50:5400
B. RTSP Transmitting Port: Port for RTSP stream.
C. RTP start and end port:
In RTSP mode, you may use TCP and UDP for connecting
TCP connection uses RTSP port (554) UDP connection uses RTP start & end port.
4. UPnP: This IP camera supports UPnP. If this service is enabled on your computer,
the camera will be automatically detected and a new icon will be added to
“My Network Places”.
Below are instructions on how to activate UPnP on your computer:
A. Open the control panel from the start menu.
B. Select “Add/Remove programs”
C. Select “Add/Remove Windows components”
D. Open “Networking Services” section
E. Click “Details” and select UPnP to setup the service.
F. Once activated, the IP camera icon will appear in “My Network Places”
G. You can now double click that icon to access the camera with your IE browser.
Network
19

Network/cont: Below is an example of the network settings menu. This is where you key in all of your IP
information from your network. These settings must be entered correctly in order for the IP camera to be
viewable over the network.
Network/cont
5. PPPoE: Check the PPPoE “Enabled” button to activate this function.
You can key in a username and password for the connection if you are using ADSL.
Send mail after dialed: When connected to the internet, this IP camera will send a
email to the specified email account. To configure the IP camera email settings,
please refer to the “Mail and FTP Settings”
20