Channel Vision 6810 User manual

6810
Color High Res Eyeball Dome w/OSD
12

Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions for future reference.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with a dry cloth.
6. Install in accordance with these instructions.
7 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
that produce heat.
8. Only use attachments/accessories specified by Channel Vision.
9. Unplug this apparatus during lightning storms.
10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the inside of the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
11. Inside of apparatus shall not be exposed to dripping or splashing and objects filled with liquids.
Introduction
Thank you for purchasing Channel Vision's 6810 high resolution dome camera.
Please take the time to read over these instructions to ensure proper installation and usage.
Features
•
•
•
•
COLOR 1/3" High Resolution CCD Sensor
700 TV Lines
0 Lux (IR On)
OSD
6810 (4) Screws
Box Contents
Items Included:
(1) 6810 camera
(4) Mounting screws
Tools & Accessories
Required (Not included):
(1) 12vDC power supply
(1) Wire stripper
(1) Small flathead screwdriver
(1) Small philips screwdriver
2

Troubleshooting
Installation
No video
Problem
Poor quality video
Power supply is disconnected or damaged
Power supply voltage is too low
Faulty cable connections
Check power supply, replace if needed
Make sure to use the correct power supply
Check with cable tester or verify cable
Possible Cause Solution
*Specifications:
Image Sensor: Sony 1/3” Hi-Res Effio-E
Picture Elements: NTSC: 976x494
Resolution: 700 lines
S/N Ratio: More than 48 dB
Min Illumination: 0 LUX (IR on)
Gamma Characteristic: 0.45
Auto Gain Control: Auto
Auto Electronic Shutter: 1/60s-1/100 000s
Scanning System: 2:1 interlace
Camera Lens: 3.6mm
Sync. System: Internal, Negative sync.
Clock Frequency: NTSC: 36
Power Requirements: 12VDC 400mA
Infrared Illumination: 30 IR LEDs
LED Wavelength: 850nm
Illumination Distance: 20 meters (60ft)
Video Output: 1 Vp-p @ 75 ohms
Weather Rating: IP66
Operating Temp: -10°C to 50°C (14°F to 122°F)
Dimensions: 69mm (W)x67mm(H)x126mm(D)
*Specifications subject to change without notice.
Specifications
Coax extension
(not included)
Power supply
(not included)
To Monitor
or
Video distribution
2-Conductor power
supply extension
(not included)
Crimp-on splice
connectors
(not included)
Power
Video
(BNC Connector)
3
6810

500-313 Rev C
www.channelvi s i o n . c o m
234 Fischer Avenue, Costa Mesa, California 92626 USA
[phone] [phone] [phone] fax
email: [email protected]
1
Channel Vision Technology will repair or replace any defect in material or
workmanship which occurs during normal use of this product with new or rebuilt
parts, free of charge in the USA, for one year from the date of original purchase. This
is a no hassle warranty with no mail in warranty card needed. This warranty does not
cover damages in shipment, failures caused by other products not supplied by
Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration
of the equipment. This warranty is extended only to the original purchaser when
purchased through an authorized reseller. A purchase receipt, invoice, or other
proof of original purchase date will be required before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling [phone]
toll free. A Return Authorization number must be obtained in advance and can be
marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights (which
vary from state to state). If a problem with this product develops during or after the
warranty period, please contact Channel Vision Technology, your dealer or any
factory-authorized service center.
Channel Vision products are not intended for use in medical, lifesaving, life
sustaining or critical environment applications. Channel Vision customers using or
selling Channel Vision products for use in such applications do so at their own risk
and agree to fully indemnify Channel Vision for any damages resulting from such
improper use or sale.