Channel MotionPro Night Owl User manual

INSTRUCTION MANUAL - Issue 1 - 02/2014 | 1
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
INSTRUCTION MANUAL
CHANNEL SAFETY SYSTEMS t: 0845 884 7000
Peterseld Business Park f: 0845 884 6000
Bedford Road
Peterseld
Hampshire e: [e-mail]
GU32 3QA w: www.channelsafety.co.uk
Security lighting range
from Channel Safety Systems
™
i
t
y
l
ig
h
ting range
a
nnel Safet
y
S
y
stem
s
NIGHT OWL

INSTRUCTION MANUAL - Issue 1 - 02/2014 | 2
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
Please read the following instructions carefully to ensure that mounting operation will be carried out in the
right way. These instructions should be properly preserved for future reference.
Safety Instructions
1. The light can not be used on building sites, engineering workshops and similar applications.
2. Replace the cracked protection glass immediately and use only original parts to substitute.
3. Before the maintenance work takes place, the power should be switched o. The maintaining should be done only by a
qualied electrician.
4. The light is only suitable for xed mounting.
Mounting position.
1. Before mounting, make sure that the electrical supply has been switched o to avoid electric shock. (see Fig.1)
2. The light should ideally be xed with the wall xing plate, open the xing plate. (see Fig.2)
3. Mark the hole positions for xing plate onto the wall. Drill and plug the wall at the marked positions. Screw the xing plate
to the wall with suitable screws (supplied). (see Fig.3)
4. Put your mains cable H05RN-F 2G 1.0mm (not included) into the junction box, Connect the mains wires, see mark N and L
(see Fig.4).
5. Attach the device to the wall plate. (see Fig.5)
6. Switch on the power for use. (see Fig.6)
Operation
The light is only suitable for xed, wall or ceiling mounting. Recommended installation height is 3
metres above ground. The maximum detection range about 10 metres and at the angle of about 140
The lights can be tilted down 90 and pan outwardly 30.
The detector head can be panned 90 to the left and 90 to the right.
The infrared detector is equipped with two adjusting knobs.
PRODUCT CODE Rated Power Weight Glass Dimensions Notes
E/FLOOD/NOWL/S 20W (2x10W) 0.7Kg 40mm x15mm 206mm x198mm
x 60mm
Electric shock protection
class: II
External light protection
class: IP54
Lamp socket size: LED
Rated voltage:
220V-240V~ 50Hz
E/FLOOD/NOWL/D 10W (4x2.5W) 0.45Kg 40mm x15mm 206mm x 90mm x
60mm
E/FLOOD/NOWL/S/PIR 20W (2x10W) 0.72Kg 40mm x15mm 251mm x 190mm
x 81mm
E/FLOOD/NOWL/D/PIR 10W (4x2.5W) 0.48Kg 40mm x15mm 238mm x 90mm x
80mm

INSTRUCTION MANUAL - Issue 1 - 02/2014 | 3
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for environmentally friendly
safe recycling.
Time adjustment
Using the dial the lighting period of the light can be adjusted after detection of the movement perceived.
This period is adjustable from 10 sec to 10 min. Turn this dial clockwise to increase the lighting period, and vice versa.
Daylight adjustment
Using the dial, the lighting value with which the infrared detector becomes activated so that it can detect, can be adjusted. The
value is adjustable to 30 lux. Turn the dial clockwise to decrease the lighting value, and vice versa.
CAUTION: The light source of lamp can not be replaced, please replace a whole new lamp if the light source is broken.

INSTRUCTION MANUAL - Issue 1 - 02/2014 | 4
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
WITHOUT PIR

INSTRUCTION MANUAL - Issue 1 - 02/2014 | 5
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
WITH PIR

INSTRUCTION MANUAL
CHANNEL SAFETY SYSTEMS t: 0845 884 7000
Peterseld Business Park f: 0845 884 6000
Bedford Road
Peterseld
Hampshire e: [e-mail]
GU32 3QA w: www.channelsafety.co.uk