Char-Broil Patio Bistro TRU Infrared 12601578 User manual

Patio Bistro _
Assembly
Guide
Model Numbers:
_26o1559
126o1578
126o1663
126o1664
12601665
12601688
126o1514-C1
ELECTRIC
(English)
42804641" o6/21/11

CAUTION: For your safety, before operating, Read Product Guide & Outdoor Cooking Guide
provided with this grill.
*SAFETY First ..... Grill components may have sharp edges. Be careful when handling grill parts
during assembly. We suggest that you wear a sturdy pair of leather gloves while handling the grill parts.
in assembl ofy__H# ....
L Carefully remove all components from the carton.
2. Familiarize yourself with the components and hardware used for assembly.
3. Please note that hardware used for assembly may not be shown actual size..
4. After removing components from the carton, split the carton open and use it as
a soft, scratch-flee work pad to assemble your grill.
BEFORE You Grill ....
1. Read Product Guide & Outdoor Cooking Guide
2. Position Grill Safely away from walls & structures.
3. Pre- Heat Grill--15 minutes on (_,High to season grill.
TOOLS REQUfRED FOR ASSEMBLY
(Not Supplied)
Phillips Head
Screwdriver
Small Adjustable
Wrench

ASSEMBEY GUIDE
0\\
X
/
/
Q
Grill
jw
V
Parts ram
L ............
i!J_J;
U_ J U
B
J
E
/
M ..............
_j
\\\K
/
Y
K_ Qty Description _ _ Description
A 1 Grill Lid M 1 GreaseTray
B 1 Lower Body N 2 Hubcap
C 1 Controller O 1 Warming Rack
D 1 ElementAssembly P 2 Axle
E 1 Wire Shelf Q 1 Heat Indicator
F 1 Wind Shield R 1 Cooking Grate
G 1 Towel Bar S 1 Cart Base
H 1 Lid Handle T 1 Cart Bracket
I 1 Control Panel U 2 Leg Cap
J 2 Wheel V 1 Heat Shield
K 1 Rear Leg Set W 1 Inner Reflector (Porcelain Bowl)
L 1 Front Leg Set X 1 Bezel
Key Q[y Description
Y 1 Grease Tray Guide
-- 1 Hardware Pack
-- 1 Assembly Guide, English
-- 1 Assembly Guide, Spanish, optional
-- 1 Assembly Guide, French, optional
-- 1 Product Guide, English
-- 1 Product Guide, Spanish, optional
-- 1 Product Guide, French,optional
-- 1 Grilling Guide, English
-- 1 Grilling Guide, Spanish, web only
-- 1 Grilling Guide, French, optional
V.t

ASSEMBLY GUIDE
Part Qty
A1- Cart Base 1
A2- Front Leg Set 1
A3- Rear Leg Set 1
A4- Wheels 2
A5- Hubcap
GRILL CART Assembly ..........
Fasteners
Ste_p___!-Attach Front Leg Set (A2) to the Cart Base
(A0 using 2 1/4-2o screws. Attach Rear
Leg Set (A3) to the Cart Base (A0 in the
same manner, using z 1/4-2o screws.
1/4x20-1/2"
screw
(qty 4)
Wheel Retaining
Clip
(qty 2) 3/8-16 Nut
(qty 2)
Axle Bolt
(qty 2)
[ After cart assembly, if'
your cart does not sit
level, use these screws to
adjust the cart.
Stea___- Attach 2 Axle Bolts to the Rear Leg
Set (A3), thread a 3/8-16 nut as shown
and tighten securely using a small
adjustable wrench.
Slide a Wheel (A4) over an Axle Bolt
and secure using a Wheel Retaining
Clip. Repeat for other side.
Position and Snap into place the
Wheel Hubcaps (A5). 1/4-20 Screws
(4 each)
Axle Nut
3/8-16
Axle Bolt
Wheel Retaining Clip - Install
after placing wheel on the axle.
Position wheel as shown
V.t .'.'.' :{ : o :<, iv<-

ASSEMBLY GUIDE
Part
A6- Cart Bracket
A7- Wire Shelf
A8- Leg End Cap
Qty
1
1
GRILL CART Assembly .............
Fasteners
1/4-2o Nut
(qty 4)
1/4x20-2"
screw
(qty 4)
C_ #10x3/8"
screw
(qty 2)
Step 3 - Carefully turn the Cart Assembly over
and allow it to rest on the tops of the leg
assemblies. Spread the leg assemblies apart just far
enough to allow the insertion of the Wire Shelf
(AT) into the 4 leg holes. Assemble the Cart
Bracket (A6) to the Cart Assembly by inserting 4
each 1/4-2ox2" screws into into corresponding
holes as shown. Allow the Cart Bracket to rest on
the floor, this will help with alignment. Secure
with 4 each, 1/4-2o nuts using a small adjustable
wrench, not supplied. FINGER TIGHTEN ONLY
AT THIS POINT. The bracket will be tightened in
step B2.
Be sure to install Cart Bracket (A6) on the side
shown. Once complete -leave the cart in the
upside down position.
Lastly, insert the Leg End Caps (AS) into the front
legs and secure with 1 each #1ox3/8" screw.
Place the Grill Bottom on the carton pad upside
down in preparation for the next step.
screws
#1ox3/8"
screws
V.t .'.'.' :{ : o :<, iv<-

.ASSP BLY<;UDE GRILL BODY Assembly ............
Part Qty.
B1- Lower Body 1
B2- Wind Shield 1
B3- Grill Lid 1
Step 1 - Attach the Lower BodyAssembly (BO to the
Cart Assembly by aligning the studs on the bottom of the
grill with the corresponding holes in the tops of the leg
assemblies. Secure with 7 each lo-24 nuts. A Nut Driver
(not supplied) will work nicely for this step.
Fasteners
10s c4e 3 "
(qty 3) 1/4-20x3/4" Fiber Washer 1/4-20 Nut 10-24 Nut
Hinge (qty 5) (qty 2) (qty 10)
screw
(qty 2)
Step 3 - Attach the Wind Shield (B2) to the Lower Body (B0
by aligning the holes in the panels with the corresponding holes in
the Lower Body. Secure with 3 lo-24 nuts, 3 lo-24x3/8" Screws,
and 3 fiber washers. The Wind Shield will rest inside the Lower
Body.
10-24x3/8"
10-24 Screws
Nuts (3 ea)h)
(3 each)
Studs
located on
Lower
Body
Assembly Fiber
Washer
(3 each)
Cart
Bracket
Step _,- With the legs assembled to the Lower
Body, tighten the 4 screws holding the Cart
Bracket in place. Once complete, turn the grill over
to the upright position.
Step 4 - Attach the Grill Lid (B3) by aligning the hinge holes
in the lid to the matching holes in the Wind Shield (B2). Insert 2
Hinge Screws into the holes and secure with 2 1/4-2o nuts and
two Fiber washers from the inside of the grill.
Fiber
Washer
(2 each)
1/4-20x3/4"
Hinge
Screws
(2 each)
/
V.t

ASSEMBLYGUIDE GRILL FINAL Assembly ............
Cl-
C2-
C3-
Part Qty
Cooking Grate 1
Warming Rack 1
Grease tray 1
NOTE: The Cooking Grate may
have sharp edges. Be very careful
when handling the Cooking Grate.
You should wear gloves when
handling the Cooking Grate.
Step 1 - With the Grill Lid open, place the Cooking Grate (C0into the Lower Body, allowing it to rest on the three brackets
spaced around the Lower Body. Be sure the slots in the Cooking Grate are facing the front of thegrill. Place the Warming Rack
(C2) into position by first hooking the center pins into the wind shield, then rotate the warming rack down into position.
Slots to
the front
Step 2 -Install the Grease Tray (C3) by sliding the tray onto the Grease Tray Rails from the rear of the grill. Note: The
grease tray rests between the grease tray rail stops. See detail shown in Figure A.
Tray
Rail Stops
V.t .'.'.' :{ : o :<, /v<-

ASSEMBLY GUIDE
Part
C4- Controller
C5 - Lid Handle
Qty
1
1
GRILL FINAL Assembly .............
Fasteners 10-24x3/8"
screw FiberWash
(qty 2) (qty 2)
NOTE: Be sure to press the controller into the receptacle as far as it will go. Route the
controller cord BEHIND the towel bar as shown.
Step 3 - Install the Controller (C4) into the receptacle. Be sure to route the controller cord behind the towel bar when
installing the controller. The control knob should be facing up as you engage the tip of the controller into the receptacle. Push
the controller in all the way until you hear a click, this will ensure your controller is installed properly:
Towel Bar
Controller
Controller Tip
Step 4 - Install the Lid Handle with 2 lo-24x3/8" screws and 2 fiber washers as shown.
Fiber
Washer
(2 each)
Ground Fault Interrupter
• Since 1971the National Electric Code (NEC) has
required Ground Fault Interrupter devices on all
outdoor circuits.
• If your residence was built before 1971,check with a
qualified electrician to determine if a Ground Fault
Interrupter protector exists.
• Do not use this appliance if the circuit does not
have GFI protection.
• Do not plug this appliance into an indoor circuit.
Congratulations! You have successfully completed the
assembly of your grill.
V.t .'.'.' :{ : o :<, iv<-