Chauvet DJ WASH FX User manual

User Manual

Page 2 of 19 Wash FX User Manual Rev. 1 User Manual Rev. 1
TABLE OF CONTENTS
1. Before You Begin.......................................................................................................... 3
What Is Included .............................................................................................................................3
Unpacking Instructions....................................................................................................................3
Claims..................................................................................................................................................... 3
Text Conventions ............................................................................................................................3
Symbols ..........................................................................................................................................3
Disclaimer .......................................................................................................................................3
Product at a Glance ........................................................................................................................4
Safety Notes....................................................................................................................................4
2. Introduction................................................................................................................... 5
Product Overview............................................................................................................................5
Product Dimensions........................................................................................................................6
3. Setup.............................................................................................................................. 7
AC Power........................................................................................................................................7
Fuse Replacement..........................................................................................................................7
Power Linking......................................................................................................................................... 7
Mounting .........................................................................................................................................8
Orientation.............................................................................................................................................. 8
Rigging ................................................................................................................................................... 8
4. Operation....................................................................................................................... 9
Control Panel Operation..................................................................................................................9
Menu Map .......................................................................................................................................9
DMX Linking..................................................................................................................................10
Configuration (DMX) .....................................................................................................................10
DMX Personalities................................................................................................................................ 10
Starting Address................................................................................................................................... 10
DMX Channel Assignments and Values.......................................................................................11
23CH .................................................................................................................................................... 11
23CH (Cont.) ........................................................................................................................................ 12
7CH ...................................................................................................................................................... 12
Wash™ FX Zones for DMX Control...................................................................................................... 12
Configuration (Standalone)...........................................................................................................13
Automatic Mode (including Sound-Active Mode).................................................................................. 13
Custom Color Mixing and Strobe Modes.............................................................................................. 14
Preset Static Color Mode...................................................................................................................... 14
Display Orientation ............................................................................................................................... 14
Display Time-Out.................................................................................................................................. 14
Software Version .................................................................................................................................. 14
Master/Slave Mode............................................................................................................................... 15
5. Maintenance .................................................................................................................16
Product Maintenance....................................................................................................................16
6. Technical Specifications..............................................................................................17
Returns..........................................................................................................................................18
Contact Us........................................................................................................................19

Wash FX User Manual Rev. 1 Page 3 of 19
1.BEFORE YOU BEGIN
What Is
Included
•Wash FX™
•Power Cord •Warranty Card •Quick Reference Guide
Unpacking
Instructions
Carefully unpack the
product immediately and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure
to report damage to the carrier immediately may invalidate your claim. In addition, keep the
box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with Chauvet within 7 days of delivery.
Text
Conventions
Convention Meaning
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this document are subject to change
without notice. Chauvet
assumes no responsibility or liability for any errors or omissions
that may appear in this manual. Chauvet reserves the right to update the existing
document or to create a new document to correct any errors or omissions.
You can download the latest version of this document from www.chauvetlighting.com.
© Copyright 2015 Chauvet. All rights reserved.
Electronically published by Chauvet in the United States of America.
Author Date Editor Updated
R. Isenstadt 02/12/15 A. Leon 02/19/15

Page 4 of 19 Wash FX User Manual Rev. 1 User Manual Rev. 1
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Active
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•The product is not intended for permanent installation.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
•Keep this User Manual for future use. If you sell the product to someone else, be
sure that they also receive this document.

Wash FX User Manual Rev. 1 Page 5 of 19
2.INTRODUCTION
Product Overview
DMX In
DMX Out
Fuse Holder
Microphone
Indicator Lights
Power Out
Safety Loop
Power In
Display
Control
Buttons
Cooling Fan

Page 6 of 19 Wash FX User Manual Rev. 1 User Manual Rev. 1
Product Dimensions
10 in
255 mm
7.1 in
180 mm 8.5 in
215 mm

Wash FX User Manual Rev. 1 Page 7 of 19
3.SETUP
AC Power
The Wash FX™ has an auto-
ranging power supply and it can work with an input voltage
range of 100 to 240 VAC, 50/60 Hz. To determine the product’s
power requirements
(
circuit breaker, power outlet, and wiring), use the current value listed on the label affixed
to the product’s back panel, or refer to the product
’s specifications chart. The listed current
rating indicates the product’s average current draw under normal conditions.
Always connect the product to a protected circuit
(circuit breaker or fuse). Make
sure the product
has an appropriate electrical ground to avoid the risk of
electrocution or fire.
To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect the product
to a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
1. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
2. Pry the fuse holder out of the housing.
3. Remove the blown fuse from the holder and replace with a fuse of the exact same
type and rating.
4. Insert the fuse holder back in place and reconnect power.
Disconnect the product from the power outlet before replacing the fuse.
Power Linking The product provides power linking via the Edison
outlet located in the back of the unit.
Please see the diagram below for further explanation.
Power Linking
Diagram
You can power link up to 11 Wash FX™ unit
s on 120 VAC or up to
22 Wash FX™ units on 230 VAC.
The power linking diagram corresponds to the North American version of the
product ONLY! If using the product
in other markets, you must consult with the
local Chauvet
distributor as power linking connectors and requirements may differ
in your country or region.
1st Product
2nd Product
3rd Product
Additional Products
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap

Page 8 of 19 Wash FX User Manual Rev. 1 User Manual Rev. 1
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in the
Safety Notes.
Orientation
The Wash FX™
may be mounted in any position; however, make sure adequate
ventilation is provided around the product.
Rigging
•Before deciding on a location for the product, always make sure there is easy access
to the product for maintenance and programming purposes.
•Make sure that the structure onto which you are mounting the product can support the
product’s weight. See the Technical Specifications for weight information.
•When mounting the product overhead, always use a safety cable. Mount the product
securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, use a mounting clamp
of appropriate weight
capacity.
•When power linking multiple products, mount the products close enough for
power
linking cables to reach.
•The bracket adjustment
knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
Mounting Diagram
Bracket
Adjustment Knobs
Mounting Clamp
(such as CLP-15 from Chauvet)
Safety Cable
(such as CH-05 from Chauvet)
Front View
Back View

Wash FX User Manual Rev. 1 Page 9 of 19
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the display.
Please refer to the Product Overview to see the button locations on the control panel.
Button Function
<MENU> Press to find an operation mode or to back out of the current menu
option
<UP> Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER>
Press to activate a menu option or a selected value
Menu Map
Mode
Programming Steps
Description
DMX Mode Addr 001–512
Selects the DMX starting
address
Software Version
Ver
XX.XX
Displays the software version
Display Orientation dISP
dISP
Normalizes the display
dSIP
Inverts the display
Display Time-Out LEd
on
Turns Display Time-Out on
oFF
Turns Display Time-Out off
Custom Color Mode VAL
rEd
0–255
Sets red value
GrEE
0–255
Sets green value
bLUE
0–255
Sets blue value
So1
Selects strobe speed 1
So2
Selects strobe speed 2
So3
Selects strobe speed 3
Preset Color Mode
CoLo
C1-C9
Sets to a preset color
Automatic Mode
AUto
rUn
Runs auto program
Slave Mode SLnd
SL-0
Sets to Slave mode 0
SL-1
Sets to Slave mode 1
DMX Personality CHnd
7CH
Selects 7CH Mode
23CH
Selects 23CH Mode

Page 10 of 19 Wash FX User Manual Rev. 1 User Manual Rev. 1
DMX Linking
The WASH™ FX works with a DMX controller. Information about DMX is in the CHAUVET®
DMX Primer, which is available from the Chauvet website
http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf.
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
DMX
Personalities
The WASH™ FX has two DMX personalities, a 7-channel personality and a 23-channel
personality.
To choose which DMX personality to use, follow the steps below:
1. Press <MENU> repeatedly to reach the menu’s main level and Addr shows on the
display.
2. Use <UP> or <DOWN> to select CHnd.
3. Press <ENTER> and either 7CH or 23CH will show on the display.
4. Use <UP> or <DOWN> to select the desired DMX personality.
5. Press <ENTER>.
Starting Address
When selecting a starting DMX address,
always consider the number of DMX channels the
selected DMX mode uses. If you
choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The WASH™ FX uses up to 23 DMX channels, which defines the highest configurable
address to 490.
If you are not familiar with the DMX protocol, download the DMX Primer from
www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU>repeatedly to reach the menu’s main level and Addr shows on the
display.
2. Press <ENTER> and 001-d512 will show on the display.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.

Wash FX User Manual Rev. 1 Page 11 of 19
DMX Channel Assignments and Values
23CH
Channel
Function
Value
Percent/Setting
1
Master Dimmer
000ó255 0–100% (only channels 6 to 23)
2 Auto Program
000
ó
005
No function
006
ó
020
Pattern 1
021
ó
035
Pattern 2
036
ó
050
Pattern 3
051
ó
065
Pattern 4
066
ó
080
Pattern 5
081
ó
095
Pattern 6
096
ó
110
Pattern 7
111
ó
125
Pattern 8
126ó140 Pattern 9
141
ó
155
Pattern 10
156
ó
170
Pattern 11
171
ó
185
Pattern 12
186
ó
200
Pattern 13
201ó215 Pattern 14
216
ó
230
Pattern 15
231
ó
245
Pattern 16
246
ó
255
Sound-Active
3
Auto Program Speed
000ó255 Slow to fast
4
Strobe
000ó255 0–20 Hz, slow to fast
5 Auto or Sound
Program
000
ó
010
No function
011
ó
127
Auto
128ó255 Sound-Active
6
Red Zone 1
000
ó
255
0–100%
7
Green Zone 1
000ó255 0–100%
8
Blue Zone 1
000
ó
255
0–100%
9
Red Zone 2
000ó255 0–100%
10
Green Zone 2
000
ó
255
0–100%
11
Blue Zone 2
000ó255 0–100%
12
Red Zone 3
000
ó
255
0–100%
13
Green Zone 3
000ó255 0–100%
14
Blue Zone 3
000
ó
255
0–100%
15
Red Zone 4
000ó255 0–100%
16
Green Zone 4
000
ó
255
0–100%
17
Blue Zone 4
000ó255 0–100%
18
Red Zone 5
000
ó
255
0–100%
19
Green Zone 5
000ó255 0–100%
20
Blue Zone5
000
ó
255
0–100%

Page 12 of 19 Wash FX User Manual Rev. 1 User Manual Rev. 1
23CH
(Cont.)
Channel
Function
Value
Percent/Setting
21
Red Zone 6
000
ó
255
0–100%
22
Green Zone 6
000
ó
255
0–100%
23
Blue Zone 6
000ó255 0–100%
7CH
Channel Function Value Setting
1 Red 000ó255 0–100%
2 Green 000ó255 0–100%
3 Blue 000ó255 0–100%
4
Strobe
000ó255 0–20 Hz, slow to fast
5 Auto Program
000
ó
005
No function
006
ó
020
Pattern 1
021
ó
035
Pattern 2
036
ó
050
Pattern 3
051ó065 Pattern 4
066
ó
080
Pattern 5
081
ó
095
Pattern 6
096
ó
110
Pattern 7
111
ó
125
Pattern 8
126ó140 Pattern 9
141ó155 Pattern10
156
ó
170
Pattern 11
171
ó
185
Pattern 12
186
ó
200
Pattern 13
201
ó
215
Pattern 14
216
ó
230
Pattern 15
231
ó
245
Pattern 16
246
ó
255
Sound-Active
6
Auto Program Speed
000
ó
255
Slow to fast
7 Auto or Sound
Program
000
ó
010
No function
011
ó
127
Auto
128
ó
255
Sound-Active
Wash™ FX Zones for DMX Control

Wash FX User Manual Rev. 1 Page 13 of 19
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
•Connect the product to a suitable power outlet.
Never connect a product that is operating in any standalone mode
to a DMX string
connected to a DMX controller. Product
s in standalone mode may transmit DMX
signals that could interfere with the DMX signals from the controller.
Automatic Mode
(including Sound-
Active Mode)
To run the Wash™ FX in automatic mode, follow the instructions below:
1. Press <MENU> to reach the menu’s main level and Addr shows on the display.
2. Use <UP> or <DOWN> until AUto shows on the display.
3. Press <ENTER> and rUn will show on the display.
4. Press <ENTER>.
NOTE: While in Automatic mode, the Wash™ FX will respond to sound.
The product will only respond to low frequencies of music (bass and drums).

Page 14 of 19 Wash FX User Manual Rev. 1 User Manual Rev. 1
Custom
Color
Mixing and Strobe
Modes
To custom mix a color and select the strobe speed, follow the instructions below:
1. Press <MENU> to reach the menu’s main level and Addr shows on the display.
2. Use <UP> or <DOWN> until VAL shows on the display.
3. Press <ENTER> and one of the following will show on the display:
•rEd (red)
•GrEE (green)
•bLUE (blue)
•So1 (strobe, slow speed)
•So2 (strobe, medium speed)
•So3 (strobe, fast speed)
4. Use <UP> or <DOWN> to select the desired color or the strobe speed setting.
5. When the desired color or strobe speed shows on the display, press <ENTER>.
With the color options, after pressing <ENTER>, the color value 0–255 (0–100%)
shows on the display. Use <UP> or <DOWN> to select the desired color value.
NOTE: Selecting 0will turn the color off.
6. Press <ENTER> to set the color value/strobe speed.
7. Repeat steps 4 to 6 until you have your desired color and strobe speed.
NOTE: For no strobe effect, do not press <ENTER> when a strobe option shows on
the display
Preset Static
Color Mode
To select a preset static color, do the following:
1. Press <MENU> to reach the menu’s main level and Addr shows on the display.
2. Use <UP> or <DOWN> until CoLo shows on the display.
3. Press <ENTER> and C1-C9 will show on the display.
4. Use the <UP> and <DOWN> buttons to select the desired color.
5. Press <ENTER>.
Display
Orientation
To set the orientation of the display, follow the instructions below:
1. Press <MENU> to reach the menu’s main level and Addr shows on the display.
2. Use <UP> or <DOWN> until dISP or dSIP shows on the display.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select either:
•dISP for normal mode.
•dSIP for inverted mode.
5. Press <ENTER>.
Display Time-Out
To set the display to turn off after inactivity or not, do the following:
1. Press <MENU> to reach the menu’s main level and Addr shows on the display.
2. Use <UP> or <DOWN> until LEd shows on the display.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select either:
•on to set the display to turn off after inactivity.
•oFF to set the display to stay on at all times.
5. Press <ENTER>.
Software Version
To view the software version, do the following:
1. Press <MENU> to reach the menu’s main level and Addr shows on the display.
2. Use <UP> or <DOWN> until Ver shows on the display.
3. Press <ENTER>.

Wash FX User Manual Rev. 1 Page 15 of 19
Master/Slave
Mode
The Master/Slave mode allows a single Wash™ FX
(the master) to control the actions of
one or more Wash™ FX products
(the slaves) without the need of a DMX controller. The
master will be set to operate in either Custom or Sound-Active mode, or an auto program,
while the slave units will be set to operate in Slave mode. On
ce set and connected, the
slaves will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Press <MENU> repeatedly until SLnd shows on the display.
2. Press <ENTER> and SL-0 or SL-1 will show on the display.
Note: SL-0 and SL-1 currently have the same functionality. Any differentiation
between the two options is reserved for future use.
3. Use <UP> or <DOWN> to select the slave mode.
4. Connect the DMX input of the first slave unit to the DMX output of the master.
5. Connect the DMX input of the subsequent slaves to the DMX output of the previous
slave.
6. Finish setting and connecting all the slaves.
Master unit:
1. Set the master to operate in Custom, Preset, or Auto mode.
2. Make the master unit the first unit in the daisy chain.
•Configure all the slave units before connecting the master to the daisy chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the master.
•Do not connect more than 31 slaves to the master.

Page 16 of 19 Wash FX User Manual Rev. 1 User Manual Rev. 1
5.MAINTENANCE
Product
Maintenance
Dust build-
up reduces light output performance and can cause overheating. This can lead
to reduction of the light source’s life and/or
mechanical wear. To maintain optimum
performance and minimize wear, clean your lighting product
s at least twice a month.
However, be aware that usage and environmental conditions could be contributing factors
to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3.
Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.
Do not spin the cooling fans using compressed air because you could damage
them.

Wash FX User Manual Rev. 1 Page 17 of 19
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
8.5 in (215 mm)
7.1 in (180 mm)
10 in (255 mm)
4.8 lb (2.2 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100 to 240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
77 W
75 W
Operating Current
1.2 A
0.6 A
Power linking current (units)
13.6 A (11 units)
13.6 A (22 units)
Fuse
F 3 A, 250 V
F 3 A, 250 V
Power I/O
U.S./Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
LED
4 W
50,000 hours
Color
Quantity
Current
Tri-color RGB
18
1.4 A
Photometrics
Parameter
Coverage angle
90°
Strobe Rate
0 to 20 Hz
Illuminance
790 lux @ 2m (per zone)
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C)
Fan-assisted Convection
DMX
I/O Connectors
Channel Range
3-pin XLR
7 or 23
Ordering
Product Name
Item Code
UPC Number
Wash™ FX
07050844
781462211929

Page 18 of 19 Wash FX User Manual Rev. 1 User Manual Rev. 1
Returns
To return a product or request support:
•In the U.S., contact Chauvet World Headquarters (See Contact Us).
•In the UK or Ireland, contact Chauvet Europe Ltd. (See Contact Us).
•In Mexico, contact Chauvet Mexico. (See Contact Us).
•In any other country, DO NOT contact Chauvet. Instead, contact your lighting
distributor. See www.chauvetlighting.com for distributors outside the U.S., UK,
Ireland, or Mexico.
Outside the U.S., UK, Ireland, or Mexico,
contact your distributor and follow their
instructions on how to return Chauvet products to them. Visit our website for
contact details.
Call the corresponding Chauvet Technical Support office and request a Return
Merchandise Authorization (RMA)
number before shipping the product. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
You must send the merchandise prepaid, in its original box, and with its original packing
and accessories. Chauvet will not issue call tags.
Clearly label the package with the RMA number. Chauvet will refuse any product returned
without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write the following information on a piece of paper and
place it inside the box:
•Your name
•Your address
•Your phone number
•RMA number
•A brief description of the problem
Be sure to pack the product properly. Any shipping
damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-boxing are recommended.
Chauvet reserves the right to use its own discretion to repair or replace returned
product(s).

Wash FX User Manual Rev. 1 Page 19 of 19
CONTACT US
WORLD HEADQUARTERS - Chauvet
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
World Wide Web www.chauvetlighting.com
UNITED KINGDOM AND IRELAND - Chauvet Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Email: [e-mail]
World Wide Web www.chauvetlighting.co.uk
MEXICO - Chauvet Mexico
General Information
Address: Av. Santa Ana 30
Parque Industrial Lerma
Lerma, Mexico C.P. 52000
Voice: [phone]
Technical Support
Email: [e-mail]
World Wide Web www.chauvet.com.mx
Outside the U.S., United Kingdom, Ireland, or Mexico, contact the dealer of record and follow their instructions to
request support or to return a product. Visit the Chauvet website for contact information.