Chauvet Professional MAVERICK FORCE 2 BEAM WASH User manual

Model ID: MAVERICKFORCE2BEAMWASH
User Manual

Maverick Force 2 BeamWash User Manual Rev. 1
Edition Notes
The Maverick Force 2 BeamWash User Manual includes a description, safety precautions, installation,
programming, operation and maintenance instructions for the Maverick Force 2 BeamWash as of the
release date of this edition.
Trademarks
Chauvet, Chauvet Professional, the Chauvet logo, Maverick, and Maverick Force 2 BeamWash are
registered trademarks or trademarks of Chauvet & Sons, LLC (d/b/a Chauvet and Chauvet Lighting) in the
United States and other countries. Other company and product names and logos referred to herein may be
trademarks of their respective companies.
Copyright Notice
The works of authorship contained in this manual, including, but not limited to, all design, text and images
are owned by Chauvet.
© Copyright 2023 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
Manual Use
Chauvet authorizes its customers to download and print this manual for professional information purposes
only. Chauvet expressly prohibits the usage, copy, storage, distribution, modification, or printing of this
manual or its content for any other purpose without written consent from Chauvet.
Document Printing
For best results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If using A4
paper (210 x 297 mm), configure the printer to scale the content accordingly.
Intended Audience
Any person installing, operating, and/or maintaining this product should completely read through the guide
that shipped with the product, as well as this manual, before installing, operating, or maintaining this
product.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However,
Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss,
damage or disruption caused by any errors or omissions in this document, whether such errors or
omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the
content of this document without any obligation to notify any person or company of such revision, however,
Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest
version from www.chauvetprofessional.com.
Document Revision
This Maverick Force 2 BeamWash User Manual is the 1st edition of this document. Go to
www.chauvetprofessional.com for the latest version.

Maverick Force 2 BeamWash User Manual Rev. 1
Table of Contents
i
TABLE OF CONTENTS
1. Before You Begin ....................................................................... 1
What Is Included ........................................................................................... 1
Claims ........................................................................................................... 1
Text Conventions .......................................................................................... 1
Symbols ........................................................................................................ 1
FCC Statement of Compliance ..................................................................... 2
RF Exposure Warning for North America and Australia................................ 2
Expected LED Lifespan................................................................................. 2
Safety Notes.................................................................................................. 3
2. Introduction ................................................................................ 4
Description .................................................................................................... 4
Features........................................................................................................ 4
Product Overview.......................................................................................... 4
Product Dimensions ...................................................................................... 5
3. Setup ........................................................................................... 6
AC Power...................................................................................................... 6
AC Plug .............................................................................................................. 6
Power Linking..................................................................................................... 6
Fuse Replacement ............................................................................................. 6
Remote Device Management (RDM) ............................................................ 6
USB Software Update ................................................................................... 6
Mounting ....................................................................................................... 7
Orientation.......................................................................................................... 7
Rigging ............................................................................................................... 7
Procedure........................................................................................................... 7
Signal Connections ....................................................................................... 8
Control Personalities .......................................................................................... 8
DMX Linking....................................................................................................... 8
Art-Net™ Connection ......................................................................................... 8
sACN Connection............................................................................................... 8
Connection Diagram .......................................................................................... 9
4. Operation .................................................................................... 10
Control Panel Description ............................................................................. 10
Battery Powered Display.................................................................................... 10
Home Screen ................................................................................................ 10
Control Panel Lock........................................................................................ 10
Passcode ........................................................................................................... 10
Technician Mode........................................................................................... 11
Menu Map ..................................................................................................... 11
Configuration (DMX, Art-Net™, sACN, WDMX)............................................ 17
Control Mode...................................................................................................... 17
Control Personalities .......................................................................................... 17
Starting Address................................................................................................. 17
Network Setup............................................................................................... 18
IP Mode........................................................................................................................... 18
Universe.......................................................................................................................... 18

Table of Contents
Maverick Force 2 BeamWash User Manual Rev. 1
ii
Manual IP Address.......................................................................................................... 18
Subnet Mask ................................................................................................................... 18
Control Channel Assignments and Value ..................................................... 18
Pixel Chart ...................................................................................................................... 18
Control Channel Assignments and Values.................................................... 19
Single Control Values......................................................................................... 19
Dual Control Movement Values ......................................................................... 25
Dual Control Pixels Values................................................................................. 28
Configuration (Settings) ................................................................................ 31
Pan Reverse ...................................................................................................... 31
Tilt Reverse ........................................................................................................ 31
Zoom Reverse.................................................................................................... 31
Screen Reverse ................................................................................................. 31
Pan Angle........................................................................................................... 31
Tilt Angle ............................................................................................................ 31
Black out on Movement...................................................................................... 31
Calibration .......................................................................................................... 31
Touchscreen Lock.............................................................................................. 31
Lock Screen ....................................................................................................... 31
Swap Pan and Tilt .............................................................................................. 32
WDMX Reset ..................................................................................................... 32
Display Backlight Timer...................................................................................... 32
Loss of Data ....................................................................................................... 32
Fan speed .......................................................................................................... 32
Color mixing mode ............................................................................................. 32
Dimmer curve..................................................................................................... 32
Dimmer speed.................................................................................................... 32
Pulse Width Modulation ..................................................................................... 32
Color balance ..................................................................................................... 33
Calibrated White................................................................................................. 33
White Balance .................................................................................................... 33
Preset select ...................................................................................................... 33
Preset sync ........................................................................................................ 33
USB Update ....................................................................................................... 33
Reset functions .................................................................................................. 34
Factory Reset..................................................................................................... 34
Test Mode ..................................................................................................... 34
Auto Test............................................................................................................ 34
Manual Test ....................................................................................................... 34
System Information ....................................................................................... 34
Offset Mode (Zero Adjust)............................................................................. 34
Web Server ................................................................................................... 35
5. Maintenance................................................................................ 36
Product Maintenance .................................................................................... 36
6. Technical Specifications ........................................................... 37
Contact Us ...................................................................................... 38
Warranty & Returns....................................................................................... 38

1
Maverick Force 2 BeamWash User Manual Rev. 1
Before You Begin
1. Before You Begin
What Is Included
Claims
Carefully unpack the product immediately and check the container to make sure all the parts are in the
package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from shipping, or show
signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier
immediately may invalidate a claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed
damage, file a claim with Chauvet within 7 days of delivery.
Text Conventions
Symbols
• Maverick Force 2 BeamWash
• Seetronic Powerkon IP65 power cable
• 2 Omega brackets with mounting hardware
• Quick Reference Guide
Convention Meaning
1–512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified
<ENTER> A key to be pressed on the product’s control panel
Symbol Meaning
Critical installation, configuration, or operation information. Not following these
instructions may make the product not work, cause damage to the product, or cause
harm to the operator.
Important installation or configuration information. The product may not function correctly
if this information is not used.
Useful information.
The term “DMX” used throughout this manual refers to the USITT DMX512-A digital data
transmission protocol.

2
Before You Begin
Maverick Force 2 BeamWash User Manual Rev. 1
FCC Statement of Compliance
This device complies with Part 15 Part B of the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
RF Exposure Warning for North America and Australia
Warning! This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and
the user. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Expected LED Lifespan
Over time, use and heat will gradually reduce LED brightness. Clustered LEDs produce more heat than single LEDs,
contributing to shorter lifespans if always used at full intensity. The average LED lifespan is 40,000 to 50,000
hours. To extend LED lifespan, maintain proper ventilation around the product, and limit the overall intensity.

3
Maverick Force 2 BeamWash User Manual Rev. 1
Before You Begin
Safety Notes
Read all the following safety notes before working with this product. These notes contain important
information about the installation, usage, and maintenance of this product.
This product contains no user-serviceable parts. Any reference to servicing in this User
Manual will only apply to properly trained, certified technicians. Do not open the housing
or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this product.
• The luminaire is intended for professional use only.
• The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer than
16.4 ft (5 m) is not expected.
• If the external flexible cable or cord of this luminaire is damaged, it shall be replaced by a special cord
or cord exclusively available from the manufacturer or its service agent.
• The light source contained in this luminaire shall only be replaced by the manufacturer or its service
agent or a similar qualified person.
• CAUTION:
• This product’s housing may be hot when operating. Mount this product in a location with adequate
ventilation, at least 20 in (50 cm) from adjacent surfaces.
• When transferring the product from extreme temperature environments, (e.g., cold truck to warm
humid ballroom) condensation may form on the internal electronics of the product. To avoid causing
a failure,
allow the product to fully acclimate to the surrounding environment before connecting it to power .
• Flashing light is known to trigger epileptic seizures. User must comply with local laws regarding
notification of strobe use.
• ALWAYS:
• Disconnect from power before cleaning the product or replacing the fuse.
• Replace the fuse with the same type and rating.
• Use a safety cable when mounting this product overhead.
• Connect this product to a grounded and protected circuit.
•DONOT:
• Open this product. It contains no user-serviceable parts.
• Look at the light source when the product is on.
• Leave any flammable material within 100 cm of this product while operating or connected to power.
• Connect this product to a dimmer or rheostat.
• Operate this product if the housing, lenses, or cables appear damaged.
• Operate this product outdoors or in any location where dust, excessive heat, water, or humidity may
affect it (adhere to standards for the published IP rating).
• ONLY use the carry handles or hanging/mounting bracket to carry this product.
•
The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at higher temperatures .
• The minimum startup temperature is -4°F (-20°C). Do not start the product at lower temperatures.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
• In the event of a serious operating problem, stop using immediately.
If a Chauvet product requires service, contact Chauvet Technical Support.

4
Introduction
Maverick Force 2 BeamWash User Manual Rev. 1
2. Introduction
Description
A lighter, brighter, tighter, faster RGBW LED yoke wash fixture with pixel mapping and zoom, the
Maverick Force 2 BeamWash incorporates the latest LED and optical technologies to project the
narrowest beams and deliver the deepest aerial washes. Foreground and background colors combine for
sizzling atmospheric effects instantrly with its built-in virtual gobo wheel. flawlessly even output, full pixel
mappiing, and smooth 16-bit fades make this fixture a force to be reckoned with, live or on camera. Take
control with DMX, RDM, sACN, Art-Net, Kling-Net, or W-DMX.
Features
• Fully featured RBGBW LED yoke wash fixture
• Pixel mapping and zoom
• Virtual color wheel with various options
• Built in virtual gobo wheel
• DMX, WDMX, sACN, Art-Net, and Kling-Net
• RDM enabled for remote addressing and trouble shooting
• 3.7 to 50.2 zoom range for variable beam sizes.
• Variable calibrated white with maximum 7500K at full output
• True 1 compatible power input
• USB-C software update port
• Battery backup display with auto rotate
• Three setup menu presets and preset sync
Product Overview
Menu
buttons
LCD
display DMX
in/out Ethernet
port
Fuse
holder
Power
in/ out
WDMX
Antenna
Carry
handle
USB
Port

5
Maverick Force 2 BeamWash User Manual Rev. 1
Introduction
Product Dimensions
11 in
278 mm
6.9 in
174 mm
13 in
330 mm
15.2 in
387 mm
4.1 in
105 mm
8.7 in
222 mm
9.3 in
236 mm

6
Setup
Maverick Force 2 BeamWash User Manual Rev. 1
3. Setup
AC Power
The Maverick Force 2 BeamWash has an auto-ranging power supply and it can work with an input voltage
range of 100 to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current
value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.
The listed current rating indicates the product’s average current draw under normal conditions.
AC Plug
The Maverick Force 2 BeamWash comes with a power input cable terminated with a Seetronic Powerkon
A connector on one end and an Edison plug on the other end (U.S. market). Use the table below to wire a
plug.
Power Linking
It is possible to power link Maverick Force 2 BeamWash products. See the table below for the current draw
at each voltage and frequency:
Never exceed 12A on a single circuit. Power-linking cables can be purchased separately.
Fuse Replacement
1. Disconnect this product from the power outlet.
2. Using a flat-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse and replace with another fuse of the same type and rating (F 10 A, 250 V).
4. Screw the fuse holder cap back in place and reconnect power.
Remote Device Management (RDM)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate
bi-directionally along existing DMX cabling. Check the DMX controller’s User Manual or with the
manufacturer as not all DMX controllers have this capability. The Maverick Force 2 BeamWash supports
RDM protocol that allows feedback to make changes to menu map options.
USB Software Update
The Maverick Force 2 BeamWash allows for software update through USB using the built-in USB port. The
product's USB port supports up to 32GB capacity and only works with FAT32 file format. To update the
software using a USB flash drive, do the following:
1. Power on the product and plug the flash drive into the USB port.
2. Once the flash drive has been detected, the message “Upgrade Firmware” will be displayed.
Press <ENTER>. If a different message appears on the display, search for the updated software in
the menu (Updated Firmware). A list of the updated software files will be displayed.
3. Select the file that needs to be uploaded. The message “Are you sure?” will be displayed. Press
<ENTER>.
4. If the selected file is correct, the update will be completed. Restart the product.
If the selected file is incorrect, the update will fail, and the display will go back to the main interface.
Repeat steps 1–3 using the correct file.
• Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure
the product has an appropriate electrical ground to avoid the risk of electrocution or
fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 to 100% switch.
Connection Wire (U.S.) Wire (Europe) Screw Color
AC Live Black Brown Yellow or Brass
AC Neutral White Blue Silver
AC Ground Green/Yellow Green/Yellow Green
100 V, 60 Hz 120 V, 60 Hz 208 V, 60 Hz 230 V, 50 Hz 240 V, 60 Hz
Current Draw 6.35 A 5.23 A 2.96 A 2.68 A 2.55 A

7
Maverick Force 2 BeamWash User Manual Rev. 1
Setup
Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.
For our Chauvet Professional line of mounting clamps, go to http://trusst.com/products/.
Orientation
Always mount this product in a safe position, making sure there is adequate room for ventilation,
configuration, and maintenance.
Rigging
Chauvet recommends using the following general guidelines when mounting this product.
• Before deciding on a location for the product, make sure there is easy access to the product for
maintenance and programming purposes.
• Make sure that the structure or surface onto which the product is being mounted can support the
product’s weight. See the Technical Specifications.
• When mounting the product overhead, always use a safety cable. Mount the product securely to a
rigging point, whether an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
Procedure
The Maverick Force 2 BeamWash comes with 2 omega brackets to which the user can directly attach
mounting clamps (sold separately). Make sure the clamps are capable of supporting the weight of this
product. Use at least two mounting points per product. For the Chauvet Professional line of mounting
clamps, go to http://www.trusst.com/products.
Mounting Diagram
Safety cable
Mounting clamp (x2)
Omega
bracket (x2)
Overhead mounting Surface mounting

8
Setup
Maverick Force 2 BeamWash User Manual Rev. 1
Signal Connections
The Maverick Force 2 BeamWash can receive a DMX, Art-Net™, or sACN, signal. The
Maverick Force 2 BeamWash has two Amphenol XLRnet through ports, 3-pin and 5-pin DMX in and out
ports. If using other compatible products with this product, it is possible to control each individually with a
single controller.
Control Personalities
The Maverick Force 2 BeamWash uses a 3-pin and 5-pin DMX data connection, WDMX, Art-Net™, Kling-
Net, or sACN for its control personalities:
• Refer to the Operation chapter to learn how to configure the Maverick Force 2 BeamWash to work
in these personalities.
•TheControl Channel Assignments and Values section provides detailed information regarding the
control personalities.
DMX Linking
The Maverick Force 2 BeamWash can link to a DMX controller using a 3-pin and 5-pin DMX connection or
a WDMX connection. For more information about DMX, read the DMX primer at: https://
www.chauvetprofessional.com/wp-content/uploads/2016/06/DMX_Primer.pdf.
Art-Net™ Connection
Art-Net™ is an Ethernet protocol that uses TCP/IP that transfers a large amount of DMX512 data using an
Amphenol XLRnet RJ45 connection over a large network. An Art-Net™ protocol document is available
from www.chauvetprofessional.com.
Art-Net™ designed by and copyright Artistic Licence Holdings Ltd.
sACN Connection
Streaming ACN (Architecture for Control Networks), also known as ANSI E1.31, is an Ethernet protocol that uses
the layering and formatting of ACN to transport DMX512 data over IP or any other ACN-compatible network.
Single Control Dual Control Movement Dual Control Pixels
Basic (20-channel) Basic (8-channel) Basic (36-channel)
Standard (68-channel) Standard (20-channel) Standard (48-channel)
Advanced (122-channel) Advanced (26-channel) Advanced (96-channel)
Tour (146-channel)
Basic2 (25-channel)
For more information about DMX standards or the DMX cables needed to link this product
to a DMX controller, download the DMX Primer from the Chauvet website:
www.chauvetprofessional.com.

9
Maverick Force 2 BeamWash User Manual Rev. 1
Setup
Connection Diagram
Computer/
Controller
(running Art-Net™
or sACN protocol)
Switch or Router
To other Art-Net™ or sACN devices
Maverick Force 2 BeamWash

10
Operation
Maverick Force 2 BeamWash User Manual Rev. 1
4. Operation
Control Panel Description
Battery Powered Display
The Maverick Force 2 BeamWash has a battery powered display which enables access to the menu when
the product is powered off. Press and hold <MENU> until the display activates (approximately 15
seconds).
Home Screen
The Maverick Force 2 BeamWash has a home screen that shows the current control protocols,
personalities, starting addresses, IP addresses, and universes. To see the home screen, press <MENU>
repeatedly until it shows on the display. From the home screen, touch any of the displayed control settings
to immediately jump to that part of the menu, such as the personality, starting address, or universe, or
press <ENTER> to reach the main menu.
Control Panel Lock
The setting locks or unlocks the control panel.
1. Go to the Settings main level.
2. Select the Lock Screen option.
3. Select NO (control panel stays unlocked) or YES (locks control panel).
Passcode
After being prompted to enter the passcode, enter the numbers 0920.
Button Name Function
<UP> Navigates upwards through the menu list or increases the value when in a function
<MENU> Exits from the current menu or function
<DOWN> Navigates downwards through the menu list or decreases the value when in a function
<LEFT> Navigates leftwards through the menu list
<ENTER> Enables the currently displayed menu or sets the selected value into the function
<RIGHT> Navigates rightwards through the menu list
When the control panel lock is activated, the product will prompt for the passcode in order
to access the menu. Enter the passcode as described below.

11
Maverick Force 2 BeamWash User Manual Rev. 1
Operation
Technician Mode
The technician mode disables the pan/tilt motors, allowing the output of the product to be aimed by hand.
To enable the technician mode of the Maverick Force 2 BeamWash, hold <UP> and <LEFT> while the
product is powering on. When the product is turned off and back on, the pan and tilt will return to normal
function.
Menu Map
Refer to the Maverick Force 2 BeamWash product page on www.chauvetprofessional.com for the latest menu
map.
Programming Levels Description
Control Settings Control Settings Main Level
Control Settings
Single Control
DMX Personality
Basic
Sets the DMX personality:
(see Control Personalities)
Standard
Advanced
Tour
Basic 2
Start Address 001–512 Sets the DMX starting address
ArtNet
Personality
Basic
Sets the Art-Net™ personality:
(see Control Personalities)
Standard
Advanced
Tour
Basic 2
Start Address 001–512 Sets the Art-Net™ starting address
Universe 000–255 Sets the Art-Net™ universe
sACN
Personality
Basic
Sets the sACN personality:
(see Control Personalities)
Standard
Advanced
Tour
Basic 2
Start Address 001–512 Sets the sACN starting address
Universe 000–256 Sets the sACN universe
WDMX Personality
Basic
Sets the WDMX personality:
(see Control Personalities)
Standard
Advanced
Tour
Basic 2
Start Address 001–512 Sets the WDMX starting address

12
Operation
Maverick Force 2 BeamWash User Manual Rev. 1
Control Settings (cont.) Control Settings Main Level
Control Settings
Dual
Control
Movement
DMX Personality
Basic Sets the DMX personality: (see
Control Personalities)
Standard
Advanced
Start Address 1–512 Sets the DMX starting address
ArtNet
Personality
Basic Sets the Art-Net™ personality:
(see Control Personalities)
Standard
Advanced
Start Address 1–512 Sets the Art-Net™ starting address
Universe 0–255 Sets the Art-Net™ universe
sACN
Personality
Basic Sets the sACN personality:
(see Control Personalities)
Standard
Advanced
Start Address 1–512 Sets the sACN starting address
Universe 0–256 Sets the sACN universe
Pixels
DMX Personality
Basic Sets the DMX personality
(see Control Personalities)
Standard
Advanced
Start Address 001–512 Sets the DMX starting address
ArtNet
Personality
Basic Sets the Art-Net™ personality:
(see Control Personalities)
Standard
Advanced
Start Address 001–512 Sets the Art-Net™ starting address
Universe 000–255 Sets the Art-Net™ universe
sACN
Personality
Basic Sets the sACN personality:
(see Control Personalities)
Standard
Advanced
Start Address 1–512 Sets the sACN starting address
Universe 0–255 Sets the sACN universe
Kling-Net Personality Basic Sets the Kling-Net personality:
(see Control Personalities)
Standard
Main Level Programming Levels Description
Test Mode
Auto Test Auto test all functions
Manual Test
Pan
000–255 Manually control and test all
settings through the control panel
Tilt
Red
Green
Blue
White
CTC
Color
Pattern
LED Macro
LED Ma. Speed
LED Ma. Fade
Programming Levels Description

13
Maverick Force 2 BeamWash User Manual Rev. 1
Operation
Test Mode
(cont.) Manual Test
(cont.)
Background
000–255 Manually control and test all
settings through the control panel
Background
Dim.
Dimmer
Shutter
Function
Zoom
Setup
Network
Settings
IP Mode
Manual Manually set IP address
DHCP Network sets IP address
Static Product sets IP address
Ip
_ _ _._ _ _._ _ _._ _ _
Sets IP address in Manual mode
SubMask
_ _ _._ _ _._ _ _._ _ _ Sets Subnet Mask in Manual mode
Pan Reverse NO Normal pan
YES Reversed pan
Tilt Reverse NO Normal tilt
YES Reversed tilt
Zoom Reverse NO Normal Zoom
YES Reversed Zoom
Screen Reverse
NO Normal display
YES Inverted display
AUTO Automatic display orientation
Pan Angle
540 540° pan range
360 360° pan range
180 180° pan range
Tilt Angle
270 270° tilt range
180 180° tilt range
90 90° tilt range
BL. O. P/T Move NO Do not black out while pan/tilt
YES Blackout while pan/tilt
Calibration NO Keep current settings
YES Calibrate touchscreen
Touchscreen
Lock
NO Display responds to touch
YES Display does not respond to touch
Lock Screen NO Lock the buttons and touch screen
Passcode: 0920
YES
Swap XY NO Do not swap pan and tilt
YES Pan controls tilt, tilt controls pan
WDMX Reset NO Do not reset WDMX
YES Reset WDMX
Backlight Timer
30S Display turns off after 30 seconds
1M Display turns off after 1 minute
5M Display turns off after 5 minutes
ON Display stays on
Loss of Data Hold Holds last signal received
Close Blacks out fixture
Main Level Programming Levels Description

14
Operation
Maverick Force 2 BeamWash User Manual Rev. 1
Setup (cont.)
Fans
Auto Fan speed according to product
temperature
Full Fan speed set on high
ECO Quiet mode
TV25
Maintains LED output up to an
ambient temperature of 77 °F (25
°C) (TV25) or 95 °F (35 °C)
(TV35).
TV35
When using these fan modes,
please set the PWM Options to
6000Hz or 15000Hz to prevent any
harmonization noise.
C Mixing Mode RGBW RGBW mode
CMY CMY mode (R=C, G=M, B=Y)
Dimmer Curve
Linear
Set the dimmer curve
Square
I Squa
SCurve
Dimmer Speed Smooth Set the dimmer speed
Fast
PWM Option
600Hz
Define Pulse Width Modulation
setting
1200Hz
2000Hz
4000Hz
6000Hz
15000Hz
Color Balance
Red
100–255
Sets red LED maximum value
Green Sets green LED maximum value
Blue Sets blue LED maximum value
White Sets white LED maximum value
Calibrated White
ON Calibrated white balance
OFF Uses maximum white values
Custom Uses custom white balance
White Balance
Red
000–255
Sets red LED maximum value
Green Sets green LED maximum value
Blue Sets blue LED maximum value
White Sets white LED maximum value
Preset Select
PRESET A
Recorded preset menu optionsPRESET B
PRESET C
Preset Sync
NO
Allows recorded preset menu
options
to be transferred to other
Maverick Force 2 BeamWash
products in the DMX daisy chain
YES
USB Update NO Update firmware via USB C
YES
Main Level Programming Levels Description

15
Maverick Force 2 BeamWash User Manual Rev. 1
Operation
Setup (cont.)
Reset Function
Pan/Tilt NO
Reset individual functions or all
functions from start-up
YES
Zoom NO
YES
All NO
YES
Factory Settings NO Reset to factory default settings
YES
Sys Info
Fixture
Information
Ver V_ Shows firmware version
Running Mode _ _ _ Shows current running mode
Address _ _ _/_ _ _ Shows current starting address
Temperature _ _ _ Shows current product
temperature in °C
Fixture Hours _ _ _ _ _ Shows number of hours product
has been powered on
Ip
_ _ _._ _ _._ _ _._ _ _ Shows current IP address
SubMask
_ _ _._ _ _._ _ _._ _ _ Shows current Subnet Mask
MAC
_ _._ _._ _._ _._ _._ Shows current MAC address
LED Hours _ _ _ _ _ Shows number of hours LEDs
have been powered on
Fan Information
Head Fan1
Speed
_ _ _ _
Shows speed of head fans in rpm
Head Fan2
Speed
_ _ _ _
Base Fan1
Speed
_ _ _ _
Base Fan2
Speed
_ _ _ _
Error Information No Error!* Shows any errors, or No Error!
Channel
Information
Frequency
_ _ _ Shows all current values from input
signals, 000–255
Pan
Pan Fine
Tilt
Tilt Fine
CTC
Color
Pattern
LED Macro
LED Ma. Speed
LED Ma. Fade
Background
Background
Dim.
Big. Dim. Fine
Dimmer
Dimmer Fine
Main Level Programming Levels Description

16
Operation
Maverick Force 2 BeamWash User Manual Rev. 1
Sys Info
(cont.)
Channel
Information
(cont.)
Shutter
_ _ _ Shows all current values from input
signals, 000–255
Zoom
Function
Red
Red Fine
Green
Green Fine
Blue
Blue Fine
White
White Fine
Dimmer
(all, 1–12)
Dimmer Fine
(all, 1–12)
Red (all, 1–12)
Red Fine
(all,
1–12 )
Green
(all, 1–12)
Green Fine
(all, 1–12)
Blue (all, 1–12)
Blue Fine
(all, 1–12)
White
(all, 1–12)
White Fine
(all, 1–12)
Main Level Programming Levels Description