Chauvet Professional RDM2go User manual

User Manual

Edition Notes
RDM2go User Manual Rev. 1
Edition
Notes
The RDM2go User Manual Rev. 1 includes a description, safety precautions, and installation,
programming, operation, and maintenance instructions for the RDM2go as of the release date
of this edition in November 2015.
Trademarks CHAUVET, the Chauvet logo and RDM2go are registered trademarks or trademarks of Chauvet
&Sons LLC.(d/b/a Chauvet and Chauvet Lighting) in the United States and other countries.
Other company and product names and logos referred to herein may be trademarks of their
respective companies.
Copyright Notice The works of authorship contained in this manual, including, but not limited to, all design, text
and images are owned by Chauvet.
©Copyright 2015 Chauvet & Sons, LLC.All rights reserved.
Electronically published by Chauvet inthe United States of America.
Manual Use Chauvet authorizes its customers to download and print this manual for professional information
purposes only. Chauvet expressly prohibits the usage, copy, storage, distribution, modification,
or printing of this manual or its content for any other purpose without written consent from
Chauvet.
Document
Printing For better results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If
using A4 paper (210 x 297 mm), configure your printer to scale the content accordingly.
Intended
Audience Any person in charge of installing, operating, and/or maintaining this product should completely
read through the guide that shipped with the product, as well as this manual, before installing,
operating, or maintaining this product.
Disclaimer Chauvet believes that the information contained in this manual is accurate in all respects.
However, Chauvet assumes no responsibility and specifically disclaims any and all liability to
any party for any loss, damage or disruption caused by any errors or omissions in this
document, whether such errors or omissions result from negligence, accident or any other
cause. Chauvet reserves the right to revise the content of this document without any obligation
to notify any person or company of such revision, however, Chauvet has no obligation to make,
and does not commit to make, any such revisions..
Document
Revision The RDM2go User Manual Rev. 1 is the first edition of this manual. Go to
for the latest version.

Table of Contents
RDM2go User Manual Rev. 1 -i-
Table of Contents
1. Before You Begin......................................................................................................................................1
What Is Included...........................................................................................................................................................1
Claims..........................................................................................................................................................................................1
Manual Conventions ....................................................................................................................................................................1
Symbols.......................................................................................................................................................................................1
Safety Notes .................................................................................................................................................................2
Personal Safety............................................................................................................................................................................2
Mounting And Rigging..................................................................................................................................................................2
Power And Wiring ........................................................................................................................................................................2
Operation.....................................................................................................................................................................................2
2. Introduction...............................................................................................................................................3
Description....................................................................................................................................................................3
Features........................................................................................................................................................................3
Overview.......................................................................................................................................................................4
Dimensions...................................................................................................................................................................5
3. Setup..........................................................................................................................................................6
DC Power......................................................................................................................................................................6
Charging the Battery....................................................................................................................................................................6
Battery Charge Notes...................................................................................................................................................................6
Storage Notes..............................................................................................................................................................................6
Connection....................................................................................................................................................................7
Remote Device Management (RDM) ...........................................................................................................................7
Ilumicode.......................................................................................................................................................................7
4. Operation...................................................................................................................................................8
Control Panel Description.............................................................................................................................................8
Programming ................................................................................................................................................................8
Menu Map.....................................................................................................................................................................9
Menu Map (Cont.).......................................................................................................................................................10
Menu Map (Cont.).......................................................................................................................................................11
Cable Test Chart.........................................................................................................................................................11
RDM............................................................................................................................................................................12
Ilumicode.....................................................................................................................................................................12
DMX Starting Address................................................................................................................................................................12
DMX Personality ........................................................................................................................................................................12
DMX Values...............................................................................................................................................................................13
Static Colors...............................................................................................................................................................................13
Dimmer ......................................................................................................................................................................................13
Color ..........................................................................................................................................................................................13
(Full Color Products)..................................................................................................................................................................13
Whites Setting............................................................................................................................................................................13
Reset to Factory Settings...........................................................................................................................................................13
Send DMX...................................................................................................................................................................14
Channel Adjustment...................................................................................................................................................................14
Send Options.............................................................................................................................................................................14
Receive DMX..............................................................................................................................................................15
View incoming DMX Values.......................................................................................................................................................15
Cable Test...................................................................................................................................................................15
Using the Cable Tester ..............................................................................................................................................................15
Power Options ............................................................................................................................................................15
Using the Power Options ...........................................................................................................................................................15
Information..................................................................................................................................................................15

Table of Contents
-ii- RDM2go User Manual Rev. 1
5. Technical Information.............................................................................................................................16
Product Maintenance..................................................................................................................................................16
6. Technical Specifications.........................................................................................................................17
Returns .......................................................................................................................................................................18
Contact Us...................................................................................................................................................19

Before You Begin
RDM2go User Manual Rev. 1 -1-
1. Before You Begin
What Is
Included •RDM2go
•Carry Pouch
•2 pc, 3- to 5-pin converters
•5-pin male to bare wire adaptor
•USB-A Male to Micro USB-B Male (3 ft)
•Warranty Card
•
Quick Reference Guide
Claims Carefully unpack the product immediately and check the box to make sure all the parts are in
the package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from
shipping or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure to
report damage to the carrier immediately may invalidate your claim. In addition, keep the box
and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with Chauvet within 7 days of delivery.
Manual
Conventions Convention Meaning
1–512 A range of values in the text
50/60 A set of mutually exclusive values in the text
<SET> A button on the product’s control panel
Settings A product function or a menu option
Mode>Settings A sequence of menu options
1–10 A range of menu values from which to choose in a menu
Yes/No A set of two mutually exclusive menu options in a menu
ON A unique value to be entered or selected in a menu
Symbols Symbols Meaning
Critical installation, configuration, or operation information. Failure to
comply with this information may cause the product not to work,
damage third-party equipment, or cause harm to the operator.
Important installation or configuration information. Failure to comply
with this information may keep the product from working.
Useful information.
The term “DMX” used throughout this manual refers to the USITT DMX512-A digital data
transmission protocol.

Before You Begin
-2- RDM2go User Manual Rev. 1
Safety Notes Read all the following Safety Notes before working with this product. These notes include
important information about the installation, usage, and maintenance of this product.
This product contains no user-serviceable parts. Any reference to servicing in this User
Manual will only apply to properly trained Chauvet certified technicians. Do not open the
housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this product.
Personal Safety •Always disconnect this product from its power source before servicing.
•
Always connect this product to a grounded circuit to avoid the risk of electrocution.
Mounting And
Rigging •The product is not intended for permanent installation.
•This product is for indoor use only! To prevent risk of fire or shock, do not expose this
product to rain or moisture. (IP20)
•CAUTION: When transferring product from extreme temperature environments, (e.g. cold
truck to warm humid ballroom) condensation may form on the internal electronics of the
product. To avoid causing a failure, allow product to fully acclimate to the surrounding
environment before connecting it to power.
•
Make sure there are no flammable materials close to this product while it is operating.
Power And
Wiring •Always make sure you are connecting this product to the proper voltage in accordance with
the specifications in this manual or on the product’s specification label.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
•Never connect this product to a dimmer pack or rheostat.
•
Never disconnect this product by pulling or tugging on the power cable.
Operation •Do not operate this product if you see damage on the housing, lenses, or cables. Have the
damaged parts replaced by an authorized technician at once.
•Do not cover the ventilation slots when operating to avoid internal overheating.
•The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at a
higher temperature.
•
In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your Chauvet product requires service, contact Chauvet
Technical Support.

Introduction
RDM2go User Manual Rev. 1 -3-
2. Introduction
Description The RDM2go is a multi-functional tool for working with lighting products over a DMX/RDM data
line. The palm-sized controller performs a multitude of tasks including RDM functionality, DMX
snapshot, test-scene record/playback, Ilumicode addressing for Iluminarc fixtures, and DMX
input/output monitoring. The RDM2go also features a built in DMX cable integrity checker, and
an easy to read OLED display. The RDM2go easily recharges via a standard micro USB jack
and comes with a convenient carry pouch and connector convertors.
Features •Control Protocol: DMX, RDM, Ilumicode
•DMX Channels: 1, 2, 3, 4, 5, 6 or 7
•Modes/Personalities (Ilumicode): 13 personalities (ARC 1, ARC 1+D, ARC2, ARC2+D,
ARC3, ARC3+D, ARC FULL, REMOTE, SOLID, SPECIAL1, SPECIAL2, VW, VW+D)
•Handheld tool for managing products and systems with DMX, RDM, and Ilumicode based
control
•Easily address, locate and monitor RDM capable fixtures
•Check DMX addressing, cabling, and store/playback basic snapshots
•Address and set personalities of Ilumicode based architectural fixtures
•Easy to read, large OLED display and easy to navigate menus
•
Comes with connector adaptors, USB charging cord and belt clip pouch

Introduction
-4- RDM2go User Manual Rev. 1
Overview
Top View
Front View
Carry Pouch
DMX In
DMX Out
Micro USB Input
Power On
Control Panel
3-to 5-pin
DMX
Adaptor
Cable Storage
5-to 3-
pin
DMX
Adaptor
Bottom View

Introduction
RDM2go User Manual Rev. 1 -5-
Dimensions
6.46 in
164 mm
2.76 in
70 mm
3.93 in
100 mm
4.80 in
122 mm
1.53 in
39 mm

Setup
-6- RDM2go User Manual Rev. 1
3. Setup
DC Power This product operates on a rechargeable lithium ion battery.
Charging the
Battery To recharge the product:
1. Plug the included cable into any USB-A female outlet.
2. Plug the Micro USB-B male end into the female socket located on top of the product.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power by unplugging it.
•When storing product for long periods of time without charging or using, only charge
product to 50% and store in a cool dry environment.
Battery Charge
Notes This product is equipped with a built-in rechargeable lithium ion battery.
•Recharge the battery within three days of last use.
•Avoid depleting the battery below 10%.
•Recharge/discharge the battery to 50% capacity before storing this product for extended
periods of time.
•For best results, charge the battery in a temperature between
32 ºF (0 ºC), and 95 ºF (35 ºC).
•When charging the battery, keep the product at least 1 m from any open flame or hot plate.
•Perform a full discharge/recharge cycle every three months.
•If the battery is completely discharged, the device cannot be turned on immediately when
the charger is connected. Allow a depleted battery to charge for a few minutes before
turning on the device.
•The device can be used while it is charging, but it may take longer to fully charge the
battery.
•While charging, the device may heat up. This is normal and should not affect the device’s
lifespan or performance. If the battery gets hotter than usual, the charger may stop
charging.
•Lithium-Ion batteries continue to slowly discharge (self-discharge) when not in use or while
in storage. Routinely check the battery’s charge status
Storage Notes •Store charged product(s) in a dry environment, away from direct sunlight.
•Charge or discharge the battery to approximately 50% of capacity at least once every six
months.
•Charge or discharge the battery to approximately 50% of capacity before storage.
•
Store the battery at temperatures between 41 °F and 68 °F (5 °C and 20 °C).
Micro USB Input

Setup
RDM2go User Manual Rev. 1 -7-
Connection
You can link the RDM2go to other DMX controlled products using a 5-pin DMX connection. If
using other DMX-compatible products with the RDM2go, you can control each individually with
a single DMX controller.
If you are not familiar with or need more information about DMX standards, Master/Slave
connectivity, or the DMX cables needed to link this product to a DMX controller,
download the DMX Primer from the Chauvet website.
Remote Device
Management
(RDM)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to
communicate bi-directionally along existing DMX cabling. Check the DMX controller’s User
Manual or with the manufacturer as not all DMX controllers have this capability. The
RDM2go supports RDM protocol that allows feedback to make changes to multiple attributes of
RDM-enabled products . Please refer to the section in this User Manual for more detailed
examples explaining how to use this function.
Ilumicode The RDM2go will work as an Ilumicode addresser using the 5-pin DMX serial connection located
at the bottom of the product and using the various adaptors included with this product and your
Iluminarc product. Download the Ilumicode User Manual from for more information about
connecting and configuring the product for Ilumicode operation.

Operation
-8- RDM2go User Manual Rev. 1
4. Operation
Control Panel
Description Button Function
Turns product On/Off
Scrolls through main level mode options and exits from the current menu or
function
Enables the currently displayed menu or sets the currently selected value
into the selected function
Navigates upwards through the menu list or increases the numeric value
when in a function
Navigates downwards through the menu list or decreases the numeric
value when in a function
Navigates left through the menu list.
Navigates right through the menu list.
Programming
Refer to the to understand the menu options. The menu map shows the main level
and a variable number of programming levels for each option.
•To go to the main menu level, press <MODE>repeatedly until the option shows on the
display. Press <ENTER> to select. This will take you to the first programming level for that
option.
•To select an option or value within the current programming level, press <UP> or <DOWN>
until the option shows on the display. Press <ENTER> to select. In this case, if there is
another programming level, you will see that first option, or you will see the selected value.
•
Press <MODE> repeatedly to exit to the previous level.

Operation
RDM2go User Manual Rev. 1 -9-
Menu Map
Main Level Programming Levels Description
RDM
No Fixtures Found! No RDM compatible products connected
to the RDM2go
Discovering... * (choose from list of products
connected)
* (choose from the
attributes unique
to each product)
Shows information about each product.
Some attributes will allow changes to be
made. See each individual products’ User
Manual and the section of this Manual
to
determine which attributes are
controllable
Ilumicode
Start Address 001–512 Sets the DMX starting address
PERSON
VW 2-channel: WW, CW control
VW+D 3-channel: WW, CW control + dimmer
ARC 1 3-channel: RGB control
ARC 1 + D 4-channel: RGB control + dimmer
ARC2 4-channel: RGBW(A) control
ARC2 + D 5-channel: RGBW(A) control + dimmer
ARC3 5-channel: RGBWA control
ARC3 + D 6-channel: RGBWA control + dimmer
ARC FULL 7-channel: RGB control + dimmer
REMOTE Reserved for future use
SOLID 1-channel: Dimmer
SPECIAL 1 See each product’s User Manual
SPECIAL 2
CALIB WHITE 01–11
RED
000–255
Determines the white balance for the color
macros
GREN
BLUE
COOL
WARM
RGBTOW AMBE Determines the white balance when
RGBTOW is active
DIMMER
OFF Dimmer works in linear mode
DIM 1
Dimmer works in non-linear mode, from
fast to slow
DIM 2
DIM 3
DIM 4

Operation
-10- RDM2go User Manual Rev. 1
Menu Map (Cont.)
Main Level Programming Levels Description
Ilumicode
(Cont.)
STATIC
RED
000–255 Configures the static color
GREN
BLUE
COOL
WARM
AMBE
SOLD
STRB 00–20 Configures strobe speed
SETTINGS COLOR
OFF Maximum output, unbalanced white
RGBTOW White output is as per CALIB >
RGBTOW settings
UC Output matches that of product’s
previous versions
RESET NO/YES Restores factory defaults
Send DMX T001 –
T512
000–
255
(000
–
100)
Edit Mode Normal Adjust each channel individually
All Adjust all channels together in
preconfigured increments.
Show Level As Decimal Determines how the dimmer levels
are displayed on the screen
Percent
Clear All Channels Sets all channels to “0”
Dmx
Sequence
Play
Sequence
Up/
Down:
Speed 0.1”–60.0”
Uses Up/Down keys to adjust the
Speed of the sequence
Left/
Right:
Fade
Uses Left/Right keys to adjust the
Fade Time of each step in the
sequence
Enter: Play/Stop Plays the DMX sequence
Edit
Sequence
Step
001
–
100
Scene
End Of
Sequence –
032
Set-up and edit the DMX sequence
Delete Sequence No/Yes Deletes/reset the DMX sequence
Store Scene Scene
1–32 Records current DMX values
Load Scene Loads a previously recorded scene

Operation
RDM2go User Manual Rev. 1 -11-
Menu Map (Cont.)
Main Level Programming Levels Description
Receive DMX R001–R512 Show Level As Decimal Determines how the dimmer levels are
displayed on the screen
Percent
Store Scene Scene 1–32 Records the current DMX values as a
scene
Load Scene Playing Scene 1–32 Scene 1–32 Loads a previously recorded scene
Cable Test In –––––– –––––– Out Tests the cable for any breaks or shorts in
the line.
Power
Options
Off Power saver feature is turned off
1 Minute Product is powered off after 1 min of
inactivity
5 Minute Product is powered off after 5 min of
inactivity
10 Minute Product is powered off after 10 min of
inactivity
Cable Test Chart
Good Bad Pin 2
Pin 1 Shorted to Pin 3

Operation
-12- RDM2go User Manual Rev. 1
RDM The RDM2go uses Remote Device Management (RDM) software that allows feedback to make
changes to connected RDM compatible products.
1. Go to the RDM main level.
2. The RDM2go will scan for RDM compatible products, Discovering... will display on the
screen.
a. No Fixtures Found – No RDM compatible products were found. Be sure your
connected products are RDM compatible check all connections and try again.
3. Select from the list of RDM compatible products displayed.
4. Select and adjust each of the available of attributes.
RDM Product
Attributes Below are some examples of more common attributes that will be listed on the LCD after
choosing from the list of available RDM compatible products. Each of these attributes may or
may not be changeable depending on each type of individual product.
•Label: Allows user input such as identity information to be stored on the products memory.
•Model: This is the name of the product that was entered at the factory level. This attribute
cannot be changed.
•Man.: Manufacture identity. This attribute cannot be changed.
•Start Address: Shows current DMX address and allows the user to change it.
•Pers.: Shows current product personality and allows user to change it.
•DMX Slots: Shows how many DMX addresses that products personality takes up. This
attribute cannot be changed.
•Slot Options:Gives a description of what each channel in that DMX personality does. This
attribute may not be available on all products.
•Moving Light Options:Gives options like P/T invert and P/T Swap. This attribute may not
be available on all products.
•Sensors Menu:Shows information from the different sensors like the temperature of
product
•Display Options:Allows user input to change the backlight level and direction of the
products display and allows user to change the address.
For more information about RDM protocol and associated attributes, go to
Ilumicode
This Main Level selection contains all the parameters for all the compatible ILUMINARC
products it can control. Consult the corresponding product’s user manual to determine which
parameters on the Ilumicode V 2.21 apply to that specific product.
DMX Starting
Address 1. Go to Iumicode > Start Address.
2. Select a starting DMX address (001–512).
3. Press <ENTER> to send the new DMX address to the product. The display will show
“SEND…”
DMX Personality 1. Go to Iumicode > PERSON and select any DMX personality.
2. Make sure to rearrange the DMX addresses of all products in the current DMX universe to
avoid address overlapping.

Operation
RDM2go User Manual Rev. 1 -13-
DMX Values Refer to the compatible ILUMINARC product’s manual for the DMX Values that correspond to
that particular product.
•To change the DMX address of a single product, make sure that there is no other
product connected to the DMX cable.
•Some personalities on this list may not apply to your ILUMINARC product. Consult
the product’s manual for more information.
Static Colors 1. Go to Iumicode > STATIC.
2. Select a color or effect (RED, GREN, BLUE, COOL, WARM, AMBE, SOLD, or STRB).
3. Select a color value (000–255) or a strobe frequency (00–20).
Dimmer This setting gives the user four different options to simulate the dimming curve of an
incandescent lighting product.
1. Go to Iumicode > DIMMER.
2. Select a dimming curve (OFF or DIM1–4).
Procedure:
DIMMER Description
OFF Dimmer curve is linear with fader
DIM1 Non-linear (fastest)
DIM2 Non-linear (fast)
DIM3 Non-linear (slow)
DIM4 Non-linear (slowest)
Color
(Full Color
Products)
1. Go to Iumicode > SETTINGS > COLOR.
2. Select the color method (OFF, RGBTOW, UC).
Details:
OFF
•When the RGB faders are all set to “255,” the output is maximum.
RGBTOW
•When the RGB faders are all set to “255,” the output is the selected White color
().
UC
•When the RGB faders are all set to “255,” the output matches the same color output of
previous versions of this product.
Whites Setting 1. Go to Iumicode > CALIB.
2. Select a white color (WHITE 1–11) or RGB TO W.
3. Select an RGB color (RED, GREN, BLUE, COOL, WARM, or AMBE).
4. Configure the color value (000–255).
5. Repeat steps 3 and 4 for the other RGB colors to obtain a white color.
6. Repeat steps 2 through 5 for the other white colors.
Reset to Factory
Settings 1. Go to Iumicode > SETTINGS > RESET.
2. Select an option (YES/NO).
Details:
The product will assume its default values as per the corresponding manual.

Operation
-14- RDM2go User Manual Rev. 1
Send DMX This Main Level selection is a single universe of DMX. This allows control each of the 512
channels individually or all channels at the same time. Other features include:
•The ability to show levels on the screen as percentages or DMX values.
•Store and recall up to 32 different static scenes
•
Create a sequence up to 100 steps using 32 scenes with adjustable fade and speed.
Channel
Adjustment 1. Go to Send DMX.
2. Select a channel (T001–T512).
3. Choose a DMX Value (000–255)
4. Repeat Steps 2 and 3 for additional channel adjustment.
In Step #3 of thesection, the values may appear as percentages and/or the values of
every channel may change when trying to adjust only 1 channel. Refer to the
section to change these settings.
Send Options This programming level gives you various customization and programming options.
1. Go to Send DMX.
2. Press <ENTER> twice to get to the Send Options menu level.
Edit Mode 1. Go to Send DMX.
2. Press <ENTER> twice.
3. Go to Edit .
4. Press <ENTER> to choose All or Normal.
Show Level As 1. Go to Send DMX.
2. Press <ENTER> twice.
3. Go to Show Level As.
4. Press <ENTER> to choose Decimal or Percent.
Clear All Channels 1. Go to Send DMX.
2. Press <ENTER> twice.
3. Go to Clear All Channels.
4. Press <ENTER> to clear. This will bring you back to the Send DMX level.
Dmx Sequence 1. Go to Send DMX.
2. Press <ENTER> twice.
3. Go to Play Sequence.
4. Press <ENTER> to play/stop sequence.
5. Press <UP> or <DOWN> to adjust the speed between steps.
6. Press <LEFT> or <RIGHT> to adjust the fade time which is the time it takes for each step to
fade up to 100% and fade down to 0.
Store Scene 1. Go to Send DMX.
2. Press <ENTER> twice.
3. Go to Store Scene.
4. Press <ENTER>.
5. Press <UP> or <DOWN> to choose a scene (Scene 1– Scene 32).
6. Select a channel (T001–T512).
7. Choose a DMX Value (000–255)
8. Press <ENTER>
9. Repeat Steps 3 through 8 for additional channel adjustment.
The RDM2go stores the last scene that was changed. To start with a clean scene, refer to
section to set all the DMX channels to 0.

Operation
RDM2go User Manual Rev. 1 -15-
Load Scene 1. Go to Send DMX.
2. Press <ENTER> twice.
3. Go to Load Scene.
4. Press <ENTER>.
5. Press <UP> or <DOWN> to choose a scene (Scene 1– Scene 32).
-OR-
1. Go to Load Scene.
2. Press <ENTER> twice.
3. Press <UP> or <DOWN> to choose a scene (Scene 1– Scene 32).
Receive DMX This Main Level selection displays incoming DMX values for each channel and allows those
values to be recorded as a scene to be played back later.
View incoming
DMX Values 1. Go to Receive DMX.
2. Press <ENTER>.
Show Level As 1. Go to Receive DMX.
2. Press <ENTER> twice.
3. Go to Show Level As.
4. Press <ENTER> to choose Decimal or Percent.
Store Scene 1. Go to Receive DMX.
2. Press <ENTER> twice.
3. Go to Store Scene.
4. Press <ENTER> to record the current input as a scene.
Cable Test This Main Level selection tests data cables for continuity.Use the
to
determine which cables are good and which are in need of repair.
Using the Cable
Tester 1. Plug both ends of a DMX cable into the RDM2go.
2. Go to Cable Test.
3. Press <ENTER>.
Power Options This Main Level selection sets the amount of time the RDM2go remains turned on after the last
user input. This auto-off option can be set to 1 Minute, 5 Minute, 10 Minute, or Off. Choosing
Off means the product will stay on until the battery is exhausted.
Using the Power
Options 1. Go to Power Options.
2. Press <ENTER>.
3. Choose the amount of time you want the product to stay on (1 Minute, 5 Minute, 10
Minute, or Off).
4. Press <ENTER> to record the current input as a scene.
Information This Main Level selection provides information about current software and the products unique
identification code.

Technical Information
-16- RDM2go User Manual Rev. 1
5. Technical Information
Product
Maintenance To maintain optimum performance and minimize wear, clean this product frequently. Usage and
environment are contributing factors in determining the cleaning frequency.
As a rule, clean this product at least twice a month. Dust build-up reduces light output
performance and can cause overheating. This can lead to reduced light source life and
increased mechanical wear.
To clean your product:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the
external vents.
4. Clean all external surfaces with a mild solution of non-ammonia glass cleaner or isopropyl
alcohol.
5. Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
6. Wipe any dirt or grime to the outside edges of the lens surface.
7. Gently polish the lens surfaces until they are free of haze and lint.
Always dry the external surfaces thoroughly and carefully after cleaning them.