Chauvet Professional Rogue Outcast 1 Beam User manual

USER MANUAL
Model ID: ROGUEOUTCAST1BEAM

Rogue Outcast 1 Beam User Manual Rev. 1
Edition Notes
The Rogue Outcast 1 Beam User Manual includes a description, safety precautions, installation,
programming, operation, and maintenance instructions for the Rogue Outcast 1 Beam.
Trademarks
CHAUVET, the Chauvet logo, and Rogue Outcast 1 Beam are registered trademarks or trademarks of
Chauvet & Sons, LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries.
Other company and product names and logos referred to herein may be trademarks of their respective
companies.
Copyright Notice
The works of authorship contained in this manual, including, but not limited to, all designs, texts, and
images are owned by Chauvet.
© Copyright 2021 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
Manual Use
Chauvet authorizes its customers to download and print this manual for professional information purposes
only. Chauvet expressly prohibits the usage, copy, storage, distribution, modification, or printing of this
manual or its content for any other purpose without written consent from Chauvet.
Document Printing
For best results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If using A4
paper (210 x 297 mm), configure the printer to scale the content accordingly.
Intended Audience
Any person installing, operating, and/or maintaining this product should completely read through the guide
that shipped with the product, as well as this manual, before installing, operating, or maintaining this product.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However,
Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss,
damage or disruption caused by any errors or omissions in this document, whether such errors or
omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the
content of this document without any obligation to notify any person or company of such revision, however,
Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest
version from www.chauvetprofessional.com
Document Revision
This Rogue Outcast 1 Beam User Manual is the 1st edition of this document. Go to
www.chauvetprofessional.com for the latest version.

Color Strike M User Manual Rev. 1
Table of Contents
1
TABLE OF CONTENTS
1. Before You Begin ....................................................................... 3
What Is Included ........................................................................................... 3
Claims ........................................................................................................... 3
Manual Conventions ..................................................................................... 3
Symbols ........................................................................................................ 3
Expected LED Lifespan................................................................................. 3
Safety Notes.................................................................................................. 4
Personal Safety.................................................................................................. 4
Mounting and Rigging ........................................................................................ 4
Power and Wiring............................................................................................... 4
Operation ...................................................................................................... 4
2. Introduction ................................................................................ 5
Description .................................................................................................... 5
Features........................................................................................................ 5
Product Overview.......................................................................................... 5
Product Dimensions ...................................................................................... 6
3. Setup ........................................................................................... 7
AC Power...................................................................................................... 7
AC Plug .............................................................................................................. 7
Fuse Replacement ............................................................................................. 7
DMX Linking.................................................................................................. 7
DMX Personalities.............................................................................................. 7
Remote Device Management (RDM) ................................................................. 7
Gobo Wheel .................................................................................................. 8
Color Wheel .................................................................................................. 9
Mounting ....................................................................................................... 10
Orientation.......................................................................................................... 10
Rigging ............................................................................................................... 10
Procedure........................................................................................................... 10
Lamp Replacement....................................................................................... 11
Procedure........................................................................................................... 11
Increasing the Lamp’s Life ................................................................................. 12
4. Operation .................................................................................... 13
Control Panel Operation................................................................................ 13
Programming................................................................................................. 13
Control Panel Lock........................................................................................ 13
Menu Map .......................................................................................................... 14
DMX Values .................................................................................................. 16
19CH .................................................................................................................. 16
16CH .................................................................................................................. 20
Address......................................................................................................... 23
Run Mode...................................................................................................... 23
DMX Personality ................................................................................................ 23
Auto Test............................................................................................................ 23
Manual Test ....................................................................................................... 23

Table of Contents
Color Strike M User Manual Rev. 1
2
Setup............................................................................................................. 23
Pan Reverse ...................................................................................................... 23
Tilt Reverse ........................................................................................................ 23
Pan Angle........................................................................................................... 23
Tilt Angle ............................................................................................................ 24
BL.O. P/T Move.................................................................................................. 24
BL.O. Color Move............................................................................................... 24
BL.O. Gobo Move .............................................................................................. 24
Lamp Controls.................................................................................................... 24
Maintenance Timer ............................................................................................ 25
Reset Function ................................................................................................... 25
Factory Reset Function ...................................................................................... 26
System Information ....................................................................................... 26
Offset Mode................................................................................................... 27
Pan..................................................................................................................... 27
Tilt ...................................................................................................................... 27
Shutter 1............................................................................................................. 27
Shutter 2............................................................................................................. 27
Color................................................................................................................... 27
Gobo .................................................................................................................. 27
Prism 1 ............................................................................................................... 27
Rotating Prism 1................................................................................................. 27
Prism 2 ............................................................................................................... 27
Rotating Prism 2................................................................................................. 27
Focus ................................................................................................................. 27
Frost ................................................................................................................... 27
Mac 4 ................................................................................................................. 27
Mac 5 ................................................................................................................. 27
Mac 6 ................................................................................................................. 27
5. Technical Information ................................................................ 28
Product Maintenance .................................................................................... 28
6. Technical Specifications ........................................................... 29
Returns............................................................................................ 30
Contact Us ...................................................................................... 31

Page 3 of 29
Rogue Outcast 1 Beam User Manual Rev. 1
BEFORE YOU BEGIN
1. Before You Begin
What Is Included
Claims
Carefully unpack the product immediately and check the container to make sure all the parts are in the
package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from shipping, or show
signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier
immediately may invalidate your claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed
damage, file a claim with Chauvet within 7 days of delivery.
Manual Conventions
Symbols
Expected LED Lifespan
LEDs gradually decline in brightness over time, primarily because of heat. LEDs that are arranged in
clusters experience higher operating temperatures than single LEDs. For this reason, operating clustered
LEDs at their fullest intensity significantly reduces the LEDs’ lifespan. Under normal conditions, this
lifespan is 40,000 to 50,000 hours. If extending this lifespan is vital, lower the operating temperature by
improving the ventilation around the product, thus reducing the ambient temperature. In addition, limiting
the overall projection intensity may extend the LEDs’ lifespan.
• Rogue Outcast 1 Beam
• Seetronic Powerkon IP65 power cord
• 2 Omega brackets with mounting hardware
• Quick Reference Guide
Convention Meaning
1–512 A range of values
50/60 A set of values of which only one can be chosen
<SET> A button on the product’s control panel
Settings A product function or a menu option
Symbol Meaning
Electrical warning. Not following these instructions may cause electrical damage to
the product, accessories, or the user.
Critical installation, configuration, or operation information. Not following these
instructions may make the product not work, cause damage to the product, or cause
harm to the operator.
Important installation or configuration information. The product may not function
correctly if this information is not used.
Useful information.
The term “DMX” used throughout this manual refers to the USITT DMX512-A
digital data transmission protocol.
!

Page 4 of 29
BEFORE YOU BEGIN
Rogue Outcast 1 Beam User Manual Rev. 1
Safety Notes
Read all the following safety notes before working with this product. These notes contain important
information about the installation, usage, and maintenance of this product.
Personal Safety
• Avoid direct eye exposure to the light source while the product is on.
• Always disconnect the product from the power source before cleaning or replacing the fuse.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Do not touch the product’s housing when operating because it may be very hot.
Mounting and Rigging
• This product is intended for professional use only.
• This product is not intended for permanent outdoor installation.
• Do not submerge this product (IP65). Regular outdoor operation is fine.
• CAUTION: When transferring product from extreme temperature environments, (e.g., cold truck to
warm, humid ballroom) condensation may form on the internal electronics of the product. To avoid
causing a failure, allow product to fully acclimate to the surrounding environment before connecting
it to power.
• Always ask for help when mounting this product to avoid personal injuries or damage to the product
• Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent
surfaces.
• Make sure there are no flammable materials close to the product when operating.
• When hanging this product, always secure to a fastening device using a safety cable.
Power and Wiring
• If the external flexible cable or cord of this luminaire is damaged, it shall be replaced by a special
cord or cord exclusively available from the manufacturer or his service agent.
• The light source contained in this luminaire shall only be replaced by the manufacturer or his service
agent or a similar qualified person.
• Always make sure you are connecting the product to the proper voltage in accordance with the
specifications in this manual or on the product’s specification label.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
• Never connect the product to a dimmer pack or rheostat.
• Never disconnect this product by pulling or tugging on the power cable.
Operation
• Do not operate this product if there is damage on the housing, lenses, or cables. Have the damaged
parts replaced by an authorized technician at once.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
• Do not cover the ventilation slots when operating to avoid internal overheating.
• Do not aim this product toward the sun. The lenses could concentrate the solar energy and cause internal
overheating.
• The maximum ambient temperature is 113 °F (45 °C). Do not operate the product at higher temperatures.
• In the event of a serious operation problem, stop using this product immediately!
This product contains no user-serviceable parts. Any reference to servicing in this User
Manual will only apply to properly trained, certified technicians. Do not open the
housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this product.
If your Chauvet product requires service, contact Chauvet Technical Support.
!

Page 5 of 29
Rogue Outcast 1 Beam User Manual Rev. 1
INTRODUCTION
2. Introduction
Description
The Rogue Outcast 1 Beam is an IP65 moving head that outputs an intensely bright 300 W beam with 14-
position, individually controllable color wheel for solid and split hues. The outdoor-ready unit raises the bar
in dynamic effect options with its ability to focus down to a pencil-thin 1° beam for tight aerials, overlapping
8- and 5-facet prisms, frost for even light distribution, and 17 static gobos for even more creative options.
Control is over DMX and RDM.
Features
• Fully featured, IP65-rated, high-powered Spot/Beam/Wash combination fixture with an USHIO 400W,
6500K with 6,000 hour life expectancy lamp, two gobo wheels, two-layer prisms, and linear zoom.
• Rugged housing designed to withstand the elements in a temporary outdoor setting
• Fast and precise movement of pan and tilt functions
• Individually controllable and layerable 8- and 5-facet prisms
• 14-position color wheel for solid and split colors
• Frost for even light distribution
•Tight1
° beam for extremely focused areal effects
• 17 static gobos for massive visual impact
• DMX and RDM protocol control
• True 1-compatible power input
Product Overview
Menu buttons
Handles
Power input
Fuse
5-pin DMX in/out
Display screen

Page 6 of 29
INTRODUCTION
Rogue Outcast 1 Beam User Manual Rev. 1
Product Dimensions
13.9 in
354 mm
21.2 in
538 mm
17.2 in
438 mm
4.5 in
144 mm
14.7 in
372 mm
4.8 in
121 mm
8.9 in
226 mm
11 in
280 mm
13.9 in
354 mm

Page 7 of 29
Rogue Outcast 1 Beam User Manual Rev. 1
SETUP
3. Setup
AC Power
Each Rogue Outcast 1 Beam has an auto-ranging power supply that works with an input voltage range of
100 to 240 VAC, 50/60 Hz. To determine the power requirements for each Rogue Outcast 1 Beam, refer to
the label affixed to the product. You can also refer to the Technical Specifications chart in this manual.
The listed current rating indicates the maximum current draw during normal operation. For more
information, download Sizing Circuit Breakers from the Chauvet website: www.chauvetprofessional.com.
AC Plug
The Rogue Outcast 1 Beam comes with a power input cord terminated with a Seetronic Powerkon IP65
connector on one end and an Edison plug on the other end (U.S. market). If the power input cord that came
with the product has no plug, or if the plug needs to be changed, use the table below to wire the new plug.
Fuse Replacement
1. Disconnect this product from the power outlet.
2. Using a flat-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse and replace with another fuse of the same type and rating (T 5 A, 250 V).
4. Screw the fuse holder cap back in place and reconnect power.
DMX Linking
The Rogue Outcast 1 Beam can be linked to a DMX controller using a 5-pin DMX connection. If using other
DMX-compatible products with this product, each can be controlled individually with a single DMX controller.
DMX Personalities
The Rogue Outcast 1 Beam uses a 5-pin DMX data connection for the 20- and 25-channel DMX personalities.
• Refer to the Introduction for a brief description of each DMX personality.
• Refer to the Operation chapter to learn how to configure the Rogue Outcast 1 Beam to work in
these personalities.
•TheDMX Values section provides detailed information regarding the DMX personalities.
Remote Device Management (RDM)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate
bi-directionally along existing DMX cabling. Check the DMX controller’s User Manual or with the
manufacturer, as not all DMX controllers have this capability. The Rogue Outcast 1 Beam supports RDM
protocol that allows feedback to make changes to menu map options.
• Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure
the product has an appropriate electrical ground to avoid the risk of electrocution or fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 to 100% switch.
Connection Wire (U.S.) Wire (Europe) Screw Color
AC Live Black Brown Yellow or Brass
AC Neutral White Blue Silver
AC Ground Green/Yellow Green/Yellow Green
Make sure to disconnect the product’s power cord before replacing a blown fuse.
Always replace the blown fuse with another of the same type and rating.
!
!

Page 8 of 29
SETUP
Rogue Outcast 1 Beam User Manual Rev. 1
Gobo Wheel
The Rogue Outcast 1 Beam includes one gobo wheel with 17 fixed gobos plus open. The diagram shows
the gobo number on the wheel as numbered in the DMX Values tables.
1
2
3
4
5
6
7
8
9
10
11
12 13 14
15
16
17
Open

Page 9 of 29
Rogue Outcast 1 Beam User Manual Rev. 1
SETUP
Color Wheel
The Rogue Outcast 1 Beam includes one color wheel with 14 fixed colors plus open (white), as indicated
below. The diagram shows the color number on the wheel, as numbered in the DMX Values tables.
6
1
3
2
4
5
78
9
10
11
12
13
14

Page 10 of 29
SETUP
Rogue Outcast 1 Beam User Manual Rev. 1
Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.
For our CHAUVET Professional line of mounting clamps, go to http://trusst.com/products/.
Orientation
Always mount this product in a safe position, making sure there is adequate room for ventilation,
configuration, and maintenance.
Rigging
Chauvet recommends using the following general guidelines when mounting this product.
• Before deciding on a location for the product, make sure there is easy access to the product for
maintenance and programming purposes.
• Make sure that the structure onto which you are mounting the product can support the product’s
weight. See the Technical Specifications for weight information.
• When mounting the product overhead, always use a safety cable. Mount the product securely to a
rigging point, whether an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
• When power linking multiple products, mount the products close enough for power linking cables to
reach.
• The bracket adjustment knobs allow for directional adjustment when aiming the product to the desired
angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the knobs.
Procedure
The Rogue Outcast 1 Beam comes with a double-bracketed yoke to which you can either attach mounting
clamps (sold separately) for hanging or simply use as a floor stand. Make sure the clamps are capable of
supporting the weight of this product. Use at least one mounting point per product. For the CHAUVET
Professional line of mounting clamps, go to http://www.trusst.com/products.
Mounting Diagram
Omega bracket
Safety cable
(such as CH-05 from Chauvet)
Mounting clamp
(such as CTC-50 or CTC-50HCN
from Chauvet)

Page 11 of 29
Rogue Outcast 1 Beam User Manual Rev. 1
SETUP
Lamp Replacement
The Rogue Outcast 1 Beam is equipped with an USHIO NSL 300 W lamp. Follow the procedure below to
safely change the lamp.
Procedure
1. Turn the product off and disconnect it from power. Wait at least 15 minutes for the lamp to cool down.
Orient the bottom of the moving head so that the fan is facing upward.
2. Remove the bottom head cover by removing 8 Allen key screws. Remove the rubber gasket, and
detach the fan cable.
Disconnect the product from power before opening.
!
Fan cable

Page 12 of 29
SETUP
Rogue Outcast 1 Beam User Manual Rev. 1
3. Remove the two power cables from the lamp.
4. Pull the spring-loaded mechanism to get enough space to slide the lamp out.
5. Reverse the steps above to install the new lamp. Do not touch the glass with bare hands.
Increasing the Lamp’s Life
• ALWAYS turn the lamp off by using the DMX controller or the product’s control panel, then wait at
least 5 minutes before switching off the product. This will keep the fans running to extract any
remaining heat from the product’s head.
• DO NOT power cycle the product unless it is necessary.
• DO NOT re-strike the lamp immediately after turning it off. Chauvet recommends waiting
5 minutes before trying to re-strike the lamp.
• DO NOT touch the lamp without wearing gloves to avoid leaving grease on the bulb or on the
contacts that could reduce the lamp’s life.
• ALWAYS change the lamp when it has reached its recommended lifespan to avoid the risk of lamp
explosion.
Do not turn the product on without a lamp!
3
4
Lamp
!

Page 13 of 29
Rogue Outcast 1 Beam User Manual Rev. 1
OPERATION
4. Operation
Control Panel Operation
Programming
Refer to the Menu Map to understand the menu options. The menu map shows the main level and a
variable number of programming levels for each option.
• To go to the desired main level, press <MENU> repeatedly until the option shows on the display.
Press <ENTER> to select. This will take you to the first programming level for that option.
• To select an option or value within the current programming level, press <UP> or <DOWN> until
the option shows on the display. Press <ENTER> to select. In this case, if there is another
programming level, you will see that first option, or you will see the selected value.
• Press <MENU> repeatedly to exit to the previous main level.
Control Panel Lock
This setting enables you to activate or disable the control panel lock, which keeps unauthorized users from
changing the product’s settings.
1. Go to the Key Lock main level.
2. Select ON or OFF.
Button Function
<MENU> Exits from the current menu or function
<ENTER> Enables the currently displayed menu or sets the currently selected value in to the
current function
<UP> Navigates upward through the menu list or increases the numeric value when in a
function
<DOWN> Navigates downward through the menu list or decreases the numeric value when in a
function
The product will prompt for a passcode to access the product’s main
programming level when the control panel lock is activated. Enter the following
passcode: <UP>, <DOWN>, <UP>, <DOWN>, <ENTER>

Page 14 of 29
OPERATION
Rogue Outcast 1 Beam User Manual Rev. 1
Menu Map
Refer to the Rogue Outcast 1 Beam product page on www.chauvetprofessional.com for the latest menu map.
Main Level Programming Levels Description
Address 001–497 Sets the starting address
Run Mode
DMX 16CH Selects the DMX personality
19CH
Auto Test Auto test all functions
Manual
Test
Pan
0–255 Manually control and test all settings through
the control panel
Pan Fine
Tilt
Tilt Fine
P/T Speed
Dimmer
Dimmer Fine
Shutter
Color
Gobo
Prism1
Prism1 Rotate
Prism2
Prism2 Rotate
Focus
Frost
P/T Macro
P/T Ma. Speed
Special Function
Setup
Pan Reverse YES Reversed pan
NO Normal pan
Tilt Reverse YES Reversed tilt
NO Normal tilt
Screen Reverse
YES Inverted screen display
NO Normal screen display
AUTO Automatic screen display
Pan Angle
540 540° pan range
360 360° pan range
180 180° pan range
Tilt Angle
270 270° tilt range
180 180° tilt range
90 90° tilt range
BL. O. P/T Move YES Blackout while panning/tilting
NO Disable blackout while panning/tilting
BL. O. Color
Move
YES Blackout while color wheel is moving
NO Disable blackout while color wheel is moving
BL. O. Gobo
Move
YES Blackout while gobo wheels are moving
NO
Disable blackout while gobo wheels are moving

Page 15 of 29
Rogue Outcast 1 Beam User Manual Rev. 1
OPERATION
Setup
(continuation)
Lamp Settings
On/Off ON Turns lamp on/off
OFF
State/Power
On
ON Defines the status of lamp when powering up
product
OFF
Off via DMX YES Turns off the unit via DMX controller
NO
On if DMX On YES
Turns lamp on when DMX signal is detected
NO
Off if DMX Off YES Turns lamp off when DMX signal is lost
NO
Ignition Delay 0–255
Selects duration of delay between product
power on and lamp power on
Low Power
Delay 0–255 Selects the duration of delay when shutter is closed and lamp enters lower power state
Reset Lamp
Time
YES Resets lamp timer to 0
NO
Leaves lamp time unchanged
Maintenance
Timer
Interval 10–250
Defines amount of hours between
maintenance
Remain Time NO
Resets amount of time remaining in
maintenance cycle
RESET
Reset Function
Pan/Tilt
YES/NO Reset individual functions or all functions
from start-up
Shutter/Prism
Color
Gobo
Frost/Focus
All
Factory Settings YES Reverts the product back to the original
factory settings
NO
Sys Info
Disp Ver V_ Shows the software version
Running Mode _ _ _ Shows current running mode
DMX Address _ _ _ Shows current DMX address
Temperature _ _ C
Shows the product’s temperature in °C
Lamp On Time _ _ _ _
Shows the amount of time the lamp has been
on (provided the counter has been reset
upon installation of new lamp)
Remaining Time _ _ _ _ Shows the amount of time remaining in
maintenance cycle
UID _ _ _ _ _ _ _ _ _ _ _ _ Shows product UID
Main Level Programming Levels Description

Page 16 of 29
OPERATION
Rogue Outcast 1 Beam User Manual Rev. 1
DMX Values
19CH
Channel Function Value Percent/Setting
1Pan 000 255 0–100%
2Panfine 000 255 Fine control (16-bit)
3Tilt 000 255 0–100%
4Tiltfine 000 255 Fine control (16-bit)
5 Pan/tilt speed 000 255 Fast to slow
6 Dimmer 000 255 0–100%
7 Dimmer fine 000 255 Fine control (16-bit)
8Strobe
000 007 No function
008 015 On
016 131 Synchronized strobe, slow to fast
132 167 Fast off, slow on (slow to fast)
168 203 Slow off, fast on (slow to fast)
204 239 Pulse strobe, slow to fast
240 250 Random strobe, slow to fast
251 255 On
9Color wheel
(see Color Wheel)
000 004 Open
005 008 Red
009 012 Orange
013 016 Cyan
017 020 Green
021 024 Lime green
025 028 Lavender
029 032 Pink
033 036 Light yellow
037 040 Magenta
041 044 Blue
045 048 Yellow
049 052 CTB 3200K
053 056 CTO 6500K
057 060 UV
061 127 Split colors
128 189 Clockwise color scroll, fast to slow
190 193 Stop
194 255 Counterclockwise color scroll, slow to fast

Page 17 of 29
Rogue Outcast 1 Beam User Manual Rev. 1
OPERATION
10 Gobo wheel
(see Gobo Wheel)
000 003 Open
004 006 Gobo 1
007 009 Gobo 2
010 012 Gobo 3
013 015 Gobo 4
016 018 Gobo 5
019 021 Gobo 6
022 024 Gobo 7
025 027 Gobo 8
028 030 Gobo 9
031 033 Gobo 10
034 036 Gobo 11
037 039 Gobo 12
040 042 Gobo 13
043 045 Gobo 14
046 048 Gobo 15
049 051 Gobo 16
052 055 Gobo 17
056 059 Open
060 063 Gobo 1 shaking, slow to fast
064 067 Gobo 2 shaking, slow to fast
068 071 Gobo 3 shaking, slow to fast
072 075 Gobo 4 shaking, slow to fast
076 079 Gobo 5 shaking, slow to fast
080 083 Gobo 6 shaking, slow to fast
084 087 Gobo 7 shaking, slow to fast
088 091 Gobo 8 shaking, slow to fast
092 095 Gobo 9 shaking, slow to fast
096 099 Gobo 10 shaking, slow to fast
100 103 Gobo 11 shaking, slow to fast
104 107 Gobo 12 shaking, slow to fast
108 111 Gobo 13 shaking, slow to fast
112 115 Gobo 14 shaking, slow to fast
116 119 Gobo 15 shaking, slow to fast
120 123 Gobo 16 shaking, slow to fast
124 127 Gobo 17 shaking, slow to fast
128 189 Clockwise gobo scroll, fast to slow
190 193 Stop
194 255 Counterclockwise gobo scroll, slow to fast
11 Prism 1 000 004 No function
005 255 Prism insert
12 Rotating prism 1
000 127 Prism index
128 189 Clockwise rotation, fast to slow
190 193 Stop
194 255 Counterclockwise rotation, slow to fast
13 Prism 2 000 004 No function
005 255 Prism index
14 Rotating prism 2
000 127 Prism index
128 189 Clockwise rotation, fast to slow
190 193 Stop
194 255 Counterclockwise rotation, slow to fast
Channel Function Value Percent/Setting

Page 18 of 29
OPERATION
Rogue Outcast 1 Beam User Manual Rev. 1
15 Focus 000 255 0–100%
16 Frost 000 255 0–100%
17 Movement macros
000 007 No function
008 015 Effect 1
016 023 Effect 2
024 031 Effect 3
032 039 Effect 4
040 047 Effect 5
048 055 Effect 6
056 063 Effect 7
064 071 Effect 8
072 079 Effect 9
080 087 Effect 10
088 095 Effect 11
096 103 Effect 12
104 111 Effect 13
112 119 Effect 14
120 127 Effect 15
128 135 Effect 16
136 143 Effect 17
144 151 Effect 18
152 159 Effect 19
160 167 Effect 20
168 175 Effect 21
176 183 Effect 22
184 191 Effect 23
192 199 Effect 24
200 207 Effect 25
208 215 Effect 26
216 223 Effect 27
224 231 Effect 28
232 239 Effect 29
240 247 Effect 30
248 255 Effect 31
18 Movement macro
speed 000 255 Fast to slow
Channel Function Value Percent/Setting