Chauvet colorband PiX IP User manual

User Manual

Page 2 of 16 COLORband PiX™ IP User Manual (Rev. 1)
TABLE OF CONTENTS
1. Before You Begin................................................................................3
What Is Included ...........................................................................................3
Unpacking Instructions..................................................................................3
Claims...................................................................................................................3
Text Conventions ..........................................................................................3
Icons.............................................................................................................3
Disclaimer.....................................................................................................3
Product at a Glance.......................................................................................4
Safety Notes .................................................................................................4
2. Introduction.........................................................................................5
Product Overview..........................................................................................5
Product Dimensions......................................................................................5
3. Setup...................................................................................................6
AC Power......................................................................................................6
Power Linking........................................................................................................6
Mounting.......................................................................................................6
Orientation.............................................................................................................6
Rigging..................................................................................................................6
4. Operation ............................................................................................7
Control Panel Operation................................................................................7
Menu Map.....................................................................................................7
Configuration (DMX)......................................................................................7
DMX Personalities and Starting Address................................................................8
DMX Channel Assignments and Values.........................................................8
7-CH......................................................................................................................8
3-CH......................................................................................................................8
4-CH......................................................................................................................8
6-CH......................................................................................................................9
9-CH......................................................................................................................9
12-CH..................................................................................................................10
18-CH..................................................................................................................10
36-CH..................................................................................................................11
Configuration (Standalone)..........................................................................12
Static Color Mode ................................................................................................12
Automatic Mode...................................................................................................12
Custom Static Color Mode....................................................................................12
Touch Control Panel Lock ....................................................................................12
Master/Slave Mode..............................................................................................13
5. Technical Information ......................................................................14
Product Maintenance ..................................................................................14
6. Technical Specifications..................................................................15
Returns.......................................................................................................16
Contact Us..................................................................................................16

COLORband PiX™ IP User Manual (Rev. 1) Page 3 of 16
1.BEFORE YOU BEGIN
What Is
Included
•1 x COLORband PiX™ IP
•1 x DMX In Adapter
•1 x DMX Out Adapter
•1 x Power Cord
•1 x Warranty Card
•1 x Quick Reference Guide
Unpacking
Instructions
Immediately upon receipt, carefully unpack the product
and check the container to make
sure you have received all the parts indicated above in good condition.
Claims
If the container or the material inside the container (the product and
included
accessories) appear damaged from shipping, or show signs of mishandling,
upon receipt
notify the carrier immediately, not CHAUVET®.
Failure to do so in a timely manner may
invalidate your claim with the carrier. In addition, keep the container and all the pa
cking
material for inspection.
For other issues such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of receiving the
merchandise.
Text
Conventions
Convention
Meaning
1~512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Icons
Icon
Meaning
Critical installation, configuration, or operation information. Failure
to comply with this information may render the product partially or
completely inoperative, cause damage to the product, or cause
harm to the user.
Important installation or configuration information. Failure to
comply with this information may prevent the product from
functioning correctly.
Useful information.
Disclaimer
The information and specifications contai
ned in this document are subject to change
without notice. CHAUVET® assumes no responsibility or liability for any errors or
omissions that may appear in this manual.
CHAUVET® reserves the right to update the
existing document or to create a new document to correct any errors or omissions.
You can download the latest version of this document from www.chauvetlighting.com.
© Copyright 2012 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Author Date Editor Date
A. Diaz 6/18/12 S. Graham 6/20/12

Page 4 of 16 COLORband PiX™ IP User Manual (Rev. 1)
Product at a
Glance
Use on Dimmer

Auto Programs

Outdoor Use

Auto-ranging Power Supply

Sound Activated

Replaceable Fuse

DMX

User Serviceable

Master/Slave

Duty Cycle

Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•Always connect the product to a GFI (ground fault interrupter) circuit to avoid the
risk of electrocution.
•Always disconnect the product from the power source before cleaning.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor or outdoor use (IP65). Do not submerge the product.
•Always install the product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•Keep this User Manual for future consultation. If you sell the product to another
user, be sure that they also receive this document.

COLORband PiX™ IP User Manual (Rev. 1) Page 5 of 16
2.INTRODUCTION
Product Overview
Product Dimensions
Touch Display
DMX In
Power In
DMX Out
Power Out

Page 6 of 16 COLORband PiX™ IP User Manual (Rev. 1)
3.SETUP
AC Power
The COLORband PiX™ IP has an auto-
ranging power supply and it can work with an
input voltage range of 100~240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a GFI protected circuit (circuit
breaker or fuse).
Make sure the product has
an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product to
a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Power Linking The
product provides a power linking option via the pigtails located on the back of the
unit.
You can daisy chain up to 9 units on 120 VAC or up to 17 units on 230 VAC.
If you choose not to use the power linking feature, be sure to use the included screw on
cap to prevent any water from getting into the power cords.
The power linking information above corresponds to the North American version
of the product ONLY! If using the product in other markets, you must consult with
the local CHAUVET® distributor as power linking connectors and requirements
may differ in your country or region.
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The COLORband PiX™ IP
may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
•Before deciding on a location for the product, always make sure there is easy
access to the product for maintenance and programming purposes.
•Make sure that the structure onto which you are mounting the product
can support
the product’s weight. Please see the Technical Specifications
section of this manual
for weight information.
•When mounting the product overhead, always use a safety cable.
Mount the
product securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The bracket has a 13 mm hole, which is appropriate for
this purpose.
•When power linking multiple products, you must always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
Mounting Diagram
Text hereMounting Bracket

COLORband PiX™ IP User Manual (Rev. 1) Page 7 of 16
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display. Please refer to the Product Overview to see the button locations
on the control
panel.
Button Function
<MENU> Press to find an operation mode or to back out of the current menu
option
<UP> Press to scroll up the list of options or to find a higher value
<DOWN>
Press to scroll down the list of options or to find a lower value
<ENTER>
Press to activate a menu option or a selected value
Menu Map
Mode Programming Steps Description
Static Colors C--
C1 Red
C2 Green
C3 Blue
C4 Cyan
C5
Magenta
C6 Yellow
C7 White
Auto Programs P--
P1
7 Color Switching
P2
7 Color Fading
P3 3 Color Switching
P4
3 Color Fading
P5 Chase Program 1
P6 Chase Program 2
Program Speed
S--
S001-S100
Selects auto program speed
Slave Mode
SLA
A__1-A126
Sets Slave Mode
Custom Color
Mixing U--
r-- Red
g-- Green
b-- Blue
Touch Control
Panel Lock PASS ON Locks touch control panel
Password is
UP,DOWN,UP,DOWN,ENTER
OFF
DMX
Personalities
and Starting
Address
3-CH
d001-d512 Selects DMX personality and starting
address
4-CH
6-CH
7-CH
9-CH
12CH
18CH
36CH
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.

Page 8 of 16 COLORband PiX™ IP User Manual (Rev. 1)
DMX
Personalities
and Startin
g
Address
The COLORband PiX™ IP has two DMX personalities, a 3-
channel mode for basic
control and a 36-channel mode with more advanced control over the lights.
The COLORband PiX™ IP uses up to 36 DMX channels in its 36-
channel DMX mode,
which defines the highest configurable address to 477.
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
If you are not familiar with the DMX protocol, you may refer to the DMX Primer at
www.chauvetlighting.com.
To select the DMX personality, do the following:
1. Press <MENU> repeatedly until 3-CH, 4-CH, 6-CH, 7CH, 9-CH, 12CH, 18CH or
36CH shows on the display.
2. Press <ENTER> to choose your DMX personality when it appears on the display.
To then choose your starting address:
1. The display should show d001once you’ve selected your DMX personality using the
steps above.
2. Use <UP> or <DOWN> to select the starting address.
3. Press <ENTER>.
DMX Channel Assignments and Values
7-CH
Channel Function Value Setting
1
Red
000

255
0~100%
2
Green
000 255
0~100%
3
Blue
000 255
0~100%
4 Color Macros
000

015
Nofunction
016 255
Color Macros
5 Speed 000 255
Speed (slow to fast)
(when Ch. 6 is between 032-233)
Strobe
(Ch. 1-Ch. 4 only)
000 015
No function
016 255
0-30 Hz
6 RGB Mode
000 031
No function
032 063
Pulse effect 0~100%
064 095
Pulse effect 100%-0
096 114
Pulse effect 100%-0-100%
115 127
Chase program
128 159
Auto fade transition
160 191
Auto snap transition (3 colors)
192 223
Auto snap transition (7 colors)
224

255
Auto programs
7
Dimmer
000 255
0~100%
3-CH
Channel Function Value Setting
1
Red
000 255
0~100%
2
Green
000 255
0~100%
3
Blue
000 255
0~100%
4-CH
Channel
Function
Value
Setting
1
Red
000 255
0~100%
2
Green
000 255
0~100%
3
Blue
000

255
0~100%
4
Dimmer
000 255
0~100%

COLORband PiX™ IP User Manual (Rev. 1) Page 9 of 16
6-CH
Channel Function Value Setting Section
1
Red
000 255
0~100%
1
2
Green
000 255
0~100%
3
Blue
000 255
0~100%
4
Red
000 255
0~100%
2
5
Green
000 255
0~100%
6
Blue
000 255
0~100%
9-CH
Channel
Function
Value
Setting
Section
1
Red
000 255
0~100%
1
2
Green
000 255
0~100%
3
Blue
000 255
0~100%
4
Red
000 255
0~100%
2
5
Green
000 255
0~100%
6
Blue
000 255
0~100%
7
Red
000 255
0~100%
3
8
Green
000 255
0~100%
9
Blue
000 255
0~100%

Page 10 of 16 COLORband PiX™ IP User Manual (Rev. 1)
12-CH
Channel Function Value Setting Section
1
Red
000 255
0~100%
1
2
Green
000 255
0~100%
3
Blue
000 255
0~100%
4
Red
000 255
0~100%
2
5
Green
000 255
0~100%
6
Blue
000 255
0~100%
7
Red
000 255
0~100%
3
8
Green
000 255
0~100%
9
Blue
000 255
0~100%
10
Red
000 255
0~100%
4
11
Green
000 255
0~100%
12
Blue
000

255
0~100%
18-CH
Channel Function Value Setting Section
1
Red
000 255
0~100%
1
2
Green
000 255
0~100%
3
Blue
000

255
0~100%
4
Red
000 255
0~100%
2
5
Green
000 255
0~100%
6
Blue
000 255
0~100%
7
Red
000 255
0~100%
3
8
Green
000

255
0~100%
9
Blue
000 255
0~100%
10
Red
000 255
0~100%
4
11
Green
000 255
0~100%
12
Blue
000 255
0~100%
13
Red
000

255
0~100%
5
14
Green
000 255
0~100%
15
Blue
000 255
0~100%
16
Red
000 255
0~100%
6
17
Green
000 255
0~100%
18
Blue
000

255
0~100%

COLORband PiX™ IP User Manual (Rev. 1) Page 11 of 16
36-CH
Channel Function Value Setting Section
1
Red
000 255
0~100%
1
2
Green
000 255
0~100%
3
Blue
000 255
0~100%
4
Red
000 255
0~100%
2
5
Green
000 255
0~100%
6
Blue
000 255
0~100%
7
Red
000 255
0~100%
3
8
Green
000 255
0~100%
9
Blue
000 255
0~100%
10
Red
000 255
0~100%
4
11
Green
000 255
0~100%
12
Blue
000

255
0~100%
13
Red
000 255
0~100%
5
14
Green
000 255
0~100%
15
Blue
000 255
0~100%
16
Red
000 255
0~100%
6
17
Green
000

255
0~100%
18
Blue
000 255
0~100%
19
Red
000 255
0~100%
7
20
Green
000 255
0~100%
21
Blue
000 255
0~100%
22
Red
000

255
0~100%
8
23
Green
000 255
0~100%
24
Blue
000 255
0~100%
25
Red
000 255
0~100%
9
26
Green
000 255
0~100%
27
Blue
000 255
0~100%
28
Red
000 255
0~100%
10
29
Green
000 255
0~100%
30
Blue
000 255
0~100%
31
Red
000 255
0~100%
11
32
Green
000 255
0~100%
33
Blue
000 255
0~100%
34
Red
000 255
0~100%
12
35
Green
000 255
0~100%
36
Blue
000 255
0~100%

Page 12 of 16 COLORband PiX™ IP User Manual (Rev. 1)
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product that is operating in any standalone mode
to a DMX string
connected to a DMX controller. Product
s in standalone mode may transmit DMX
signals that could interfere with the DMX signals from the controller.
Static Color Mode
To enable the Static Color Mode, do the following:
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to choose a color (C1-C7).
4. Press <ENTER>.
Automatic Mode
To enable the Automatic Mode, follow the instructions below:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to choose your auto program (P1-P6).
4. Press <ENTER>.
You can adjust the speed of the automatic program as well.
1. Press <MENU> repeatedly until S-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to adjust the d
uration of each step of the automatic program
from S001(slow) to S100 (fast).
4. Press <ENTER>.
Custom Static
Color Mode
To enable the Custom Static Color Mode, follow the instructions below:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER> to choose between colors (r--, g--, b--).
3. Press <UP> or <DOWN> to choose the intensity of the color (r000-100).
4. Repeat the steps to mix additional colors to create the color you need.
5. Press <ENTER>.
Touch Control
Panel Lock
To enable the touch panel lock, follow the instructions below:
1. Press <MENU> repeatedly until PASS shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until ON
shows on the display to enable the touch panel
lock.
To disable the touch panel lock so you can resume functionality, follow the steps below:
1. Press <UP>, <DOWN>, <UP>, <DOWN>, <ENTER> to disable the
touch panel
lock.
2. Press <MENU> to move through the menus as normal.
In situations where water may flow onto the touch display, use the Touch Panel
Control Lock so that the water does not reset the product’s settings.

COLORband PiX™ IP User Manual (Rev. 1) Page 13 of 16
Master/Slave
Mode
The Master/Slave mode allows a single COLORband PiX™ IP unit (the “master”) to
control the actions of one or more COLORband PiX™ IP
units (the “slaves”) without the
need of a DMX controller. The master unit will be set to operate in a standalone mode
while the slave units will be set to operate in Slave Mode. Once set and connected, the
slave units will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Press <MENU>repeatedly until SLA shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to 001.
4. Connect the DMX input of the first slave unit to the DMX output of the master unit.
5. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
6. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in a standalone mode.
2. Make the master unit the first unit in the daisy chain.
•Configure all the slave units b
efore connecting the master unit to the daisy
chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller
may interfere with the signals from the
master unit.
•Do not connect more than 31 slave units to the master unit.

Page 14 of 16 COLORband PiX™ IP User Manual (Rev. 1)
5.TECHNICAL INFORMATION
Product
Maintenance
Dust build up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life.
To maintain optimum performance and
minimize wear, you should clean your lighting products at least twice a month. However,
be aware that usage and environmental conditions could be contributing factors to
increase the cleaning frequency.
To clean the product, follow the instructions below:
•Unplug the product from power.
•Wait until the product is cold.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
•Clean all external optics and glass/transparent surfaces with a mild soap solution,
ammonia-free glass cleaner, or isopropyl alcohol.
•Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
•Softly drag any dirt or grime to the outside of the external optics or glass/transparent
surface.
•Gently polish the external optics and glass/transparent surfaces until they are free of
haze and lint.
Always dry the external optics and glass/transparent
surfaces carefully after
cleaning them.

COLORband PiX™ IP User Manual (Rev. 1) Page 15 of 16
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
39 in (993 mm)
3.9 in (100 mm)
6.8 in (173 mm)
13.5 lbs (6.1 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
98 W
103 W
Operating
0.7 A
0.4 A
Power linking current (units)
8 A (9 units)
8 A (17 units)
Fuse
F 2 A, 250 V (internal)
F 2 A, 250 V (internal)
Power I/O
US/Worldwide
UK/Europe
Power input connector
Proprietary
Proprietary
Power output connector
Proprietary
Proprietary
Power Cord plug
Edison (US)
Local plug
Light Source
Type
Power
Lifespan
LED
3 W
50,000 hours
Color
Quantity
Current
Tri-color
12
350 mA
Photo Optic
Parameter
Illuminance @ 2 m
1,952 lux
Beam angle
20º
Field angle
34°
Strobe rate
0–30 Hz
Thermal
Maximum External Temp.
Minimum Startup Temp.
Cooling System
113° F (45° C)
-4° F (-20° C)
Convection
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Proprietary
3, 4, 6, 7, 9, 12, 18, 36
Ordering
Product Name
Item Code
Item Number
COLORband PiX™ IP
03030543
COLORBANDPIXIP

Page 16 of 16 COLORband PiX™ IP User Manual (Rev. 1)
In case you need to return a product or request support, follow the procedure below:
•If you live in the U.S., contact CHAUVET® World Headquarters (see below).
•If you live in the UK or Ireland, contact CHAUVET® Europe Ltd. (see below).
•If you live in any other country, DO NOT contact CHAUVET®. Instead, contact your
distributor of record. See www.chauvetlighting.com for distributors outside the U.S.,
United Kingdom, or Ireland.
If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of
record and follow their instructions on how to return CHAUVET® product
s to
them. Visit our website for contact details.
Returns
Call the corresponding CHAUVET®
Tech Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product. Be pr
epared to
provide the model number, serial number, and a brief description of the cause for the
return.
You must send the merchandise prepaid, in its original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write t
he following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•The RMA number
•A brief description of the problem
Be sure to pack the product
properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. As a suggestion, proper UPS packing or double-
boxing is always a safe method to use.
CHAUVET®
reserves the right to use its own discretion to repair or replace
returned product(s).
Contact Us
World Headquarters
CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
United Kingdom & Ireland
CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk