Chauvet Pro-D6 User manual

Snapshot
OK on Dimmer
Outdoor OK
Sound Activated
DMX512
Master/Slave
115V/230V Switch
Circuit Breaker
User Serviceable
Duty Cycle
Pro-D6™
USER MANUAL
3000 N 29th Ct, Hollywood, FL 33020 U.S.A.
[phone] – [phone]
FAX [phone]
www.chauvetlighting.com

TABLE OF CONTENTS
1. BEFORE YOU BEGIN................................................................................................................................3
WHAT IS INCLUDED......................................................................................................................................... 3
UNPACKING INSTRUCTIONS............................................................................................................................. 3
AC POWER ................................................................................................................................................... 3
CONTACT US................................................................................................................................................. 3
SAFETY INSTRUCTIONS................................................................................................................................... 4
2. INTRODUCTION ........................................................................................................................................ 5
FEATURES..................................................................................................................................................... 5
PRODUCT OVERVIEW ..................................................................................................................................... 6
3. SETUP........................................................................................................................................................ 7
FIXTURE LINKING ........................................................................................................................................... 7
Data Cabling ........................................................................................................................................... 7
DMX Data Cable............................................................................................................................... 7
Cable Connectors............................................................................................................................. 8
3-Pin to 5-Pin Conversion Chart....................................................................................................... 8
SETTING UP A DMX SERIAL DATA LINK............................................................................................................ 8
MOUNTING.................................................................................................................................................... 9
Orientation........................................................................................................................................ 9
Rigging ............................................................................................................................................. 9
4. OPERATING INSTRUCTIONS................................................................................................................... 9
NAVIGATING THE CONTROL PANEL .................................................................................................................. 9
NOTE:LINE AMUST BE USED WHEN ONLY ONE LINE IS NEEDED IN ORDER FOR THE UNIT TO FUNCTION PROPERLY.
MENU MAP...................................................................................................................................................10
Menu Functions .....................................................................................................................................11
User Configurations ...............................................................................................................................11
To SET the DMX address:...............................................................................................................11
To set maximum output value in dmx mode: ...................................................................................11
To manually set dimming:................................................................................................................11
GENERAL TROUBLESHOOTING........................................................................................................................12
TECHNICAL SUPPORT....................................................................................................................................13
5. APPENDIX.................................................................................................................................................13
DMX PRIMER...............................................................................................................................................13
GENERAL MAINTENANCE ...............................................................................................................................14
RETURNS PROCEDURE..................................................................................................................................14
CLAIMS........................................................................................................................................................14
TECHNICAL SPECIFICATIONS ..........................................................................................................................15
Pro-D6 User Manual 2 2/18/2008 12:58 PM

1. BEFORE YOU BEGIN
What is included
¾1 x Pro-D6™
¾Warranty Card
¾User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power
To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average
current draw under normal conditions. All fixtures must be powered directly off a switched circuit and
cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch. Before applying power to a fixture, check that the
source voltage matches the fixture’s requirement. Check the fixture or device carefully to make sure
that if a voltage selection switch exists that it is set to the correct line voltage you will use.
Warning! Verify that the input voltage specified on your unit matches the line voltage applied.
Damage to your fixture may result if the line voltage applied does not match the
voltage indicated on the unit. All fixtures must be connected to circuits with a
suitable Earth Ground.
Contact Us
World Wide
General Information CHAUVET
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support CHAUVET
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com
Pro-D6 User Manual 3 2/18/2008 12:58 PM

Safety Instructions
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this
product.
•Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
•This product is intended for indoor use only!
•To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no
flammable materials close to the unit while operating.
•The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing lamp or fuse and be sure to
replace with same lamp source.
•Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use
its carrying handles.
•Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate fixture at temperatures higher
than this.
•In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•Never connect the device to a dimmer pack.
•Make sure the power cord is never crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET at: 954-929-1115.
Pro-D6 User Manual 4 2/18/2008 12:58 PM

2. INTRODUCTION
Features
CONTROL FEATURES
•6-channel DMX-512 dimmer/switch
•Dimmer curve selection for each channel: square, switch or linear
•Each channel can be set as either dimmer or relay
•Each channel can be set to any DMX address
ADDITIONAL FEATURES
•Dual 20A power lines (requires 2 separate circuits)
•Individual switch, circuit breaker and plug per line
•Accommodates different voltages per line (simultaneously)
Pro-D6 User Manual 5 2/18/2008 12:58 PM

Product Overview
Line A
(
Channel 1-3
)
DMX Out
Line B
(Channels 4-6)
Line B
Circuit Breake
r
Line A
Circuit Breake
r
DMX In
Line B
Power
Cord
Line A
Power Switch
Line B
Power Switch
Line A
Power
Cord
20A Plug
Connection
Pro-D6 User Manual 6 2/18/2008 12:58 PM

3. SETUP
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a serial data link determines the number
of fixtures the data link can support.
Important: Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA-485
standard no more than 32 devices should be connected on one data link. Connecting more than 32
fixtures on one serial data link without the use of a DMX optically-isolated splitter may result in
deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 meters (1640 ft.)
Maximum recommended number of fixtures on a serial data link: 32 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
DMX DATA CABLE
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable will
have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor and shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
POWER CONNECTION
The Pro-D6 has been designed to work on multiple input voltages (115V and 230V) simultaneously,
and comes fitted with 20 amp connectors for this purpose. For example, Line A can be plugged into
115V and Line B can be plugged into 230V. Any voltage between 100 and 264 volts may be used.
Pro-D6 User Manual 7 2/18/2008 12:58 PM

CABLE CONNECTORSCABLE CONNECTORS
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
COMMON
DMX
+
DMX -
INPUT OUTPUT
1
3
2
1
3
2
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
Termination reduces signal errors. To
avoid signal transmission problems
and interference, it is always
advisable to connect a DMX signal
terminator.
1
3
2
DMX connector configuration
CAUTION Do not allow contact between the common and the fixture’s chassis ground. Grounding the common
can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to
verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.
CAUTION Do not allow contact between the common and the fixture’s chassis ground. Grounding the common
can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to
verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.
3-PIN TO 5-PIN CONVERSION CHART3-PIN TO 5-PIN CONVERSION CHART
Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
CHAUVET Model No: DMX5M, or DMX5F.
The chart below details a proper cable conversion:
Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
CHAUVET Model No: DMX5M, or DMX5F.
The chart below details a proper cable conversion:
3PIN TO 5PIN CONVERSION CHART3 PIN TO 5PIN CONVERSION CHART
ConductorConductor 3 Pin Female (output)3 Pin Female (output) 5 Pin Male (Input)5 Pin Male (Input)
Ground/Shield Pin 1 Pin 1
Data ( - ) signal Pin 2 Pin 2
Data ( + ) signal Pin 3 Pin 3
Do not use Do not use
Do not use Do not use
This drawing provides a
general illustration of the
DMX Input/Output panel of
a lighting fixture.
Universal DMX Controller
Setting up a DMX Serial Data Link
1. Connect the (male) 3 pin connector side of
the DMX cable to the output (female) 3 pin
connector of the controller.
2. Connect the end of the cable coming from
the controller which will have a (female) 3
pin connector to the input connector of the
next fixture consisting of a (male) 3 pin
connector.
3. Then, proceed to connect from the output
as stated above to the input of the following
fixture and so on.
CHAUVET Certified DMX Data Cables
Order Code Description
DMX1.5 DMX Cable 1.5m/4.9ft
DMX4.5 DMX Cable 4.5m/14.8ft
DMX10 DMX Cable 10m/32.8ft Continue the link
Pro-D6 User Manual 8 2/18/2008 12:58 PM

Mounting
ORIENTATION
This fixture may be mounted in any position provided there is adequate room for ventilation.
RIGGING
Hanging Clamp
It is important never to obstruct the fan or vents pathway. Mount the
fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the
fixture by loosening both knobs and tilting the fixture. After finding the
desired position, retighten both knobs.
•When selecting installation location, take into consideration lamp
replacement access and routine maintenance.
•Safety cables must always be used. Note!
Clamp is sold separatel
•Never mount in places where the fixture will be exposed to rain, high
humidity, extreme temperature changes or restricted ventilation.
y
.
4. OPERATING INSTRUCTIONS
Navigating the Control Panel
Access control panel functions using the four panel buttons located directly underneath the LCD
Display.
ENTER MENU
Button Function
<UP> Scrolls through menu options in ascending
order
<DOWN> Scrolls through menu options in descending
order
<ENTER> Used to select and store the current menu
or option within a menu
<MENU> Used to access the menu or to return to a
previous menu option
The Control Panel LED Display shows the menu items you select from the menu map on page 10.
When a menu function is selected, the display will show immediately the first available option for the
selected menu function. To select a menu item, press <ENTER>.
Pressing the <MENU> button will allow access to the top of the menu map. What appears on the
bottom line of the display is one of the four choices in the menu map. Use the <UP> and <DOWN>
buttons to navigate the menu map and menu options. Press the <ENTER> button to access the menu
function currently displayed, or to enable a menu option. To return to the previous option or menu
without changing the value, press the <MENU> button.
Note: Line A must be used when only one line is needed in order for the unit to function properly.
Pro-D6 User Manual 9 2/18/2008 12:58 PM

Menu Map
Pro-D6 User Manual 10 2/18/2008 12:58 PM