Checkpoint 2200 Instruction Manual

Classification [Protected] P/N:706515
© 2015 Check Point Software Technologies Ltd. All rights reserved.
For a list of our trademarks, please refer to: www.checkpoint.com/copyright.html.
For a list of our Third Party Copyright notices, please refer to: www.checkpoint.com/3rd_party_copyright.html
Check Point 2200 and 2200B
Installing and Removing Memory
706515
Protected
2015
Important - We recommend that only experienced personnel install
or remove hardware components. Installing or removing
components incorrectly can permanently damage the appliance.
Preparing the Appliance
Before you start to install or remove memory DIMMs, make sure that:
You can connect to the WebUI or CLI to shut down the appliance.
The appliance is in a clean environment and on a level surface.
You can physically access and open the cover of the appliance.
You have the Check Point memory DIMM upgrade kit.
Important - To protect the appliance and the memory modules
from electrostatic discharge damage, make sure that you are
properly grounded before you touch these components. Read the
Health and Safety Information in the Check Point 2200 Appliances
Getting Started Guide before you start to prepare the appliance.
We recommend that you use the grounding wrist strap that is
included in the upgrade kit.

2
Upgrade Kit Contents
Installation guide - Check Point 2200 and 2200B Installing and
Removing Memory
Memory DIMMs
Screwdriver
Upgrade kit sticker
ESD grounding strap (anti-static)
To prepare the appliance:
1. Use one of these options to shut down the appliance:
From the WebUI or the CLI
Use the power switch to turn off the power
2. Remove the power cords from the appliance.
3. Remove the warranty sticker from the appliance cover screw.
4. Turn over the appliance, so that it is lying on its cover.
5. Remove the appliance cover screws.
Note - Only use the screwdriver that is included in the upgrade kit to
open and replace the appliance cover.
6. Turn over the appliance, so that the cover is at the top.
7. Put on the ESD strap and attach the other end to a grounding point.
8. Remove the top cover from the appliance.

3
Check Point 2200 and 2200B lying on its cover
Item
Description
1
Bottom of the appliance
2
Four appliance cover screws
Note - Two screws are located on the bottom of the
appliance

4
DIMM Configuration
These are the memory configurations for the 2200 and 2200B appliances:
2200 appliance (default) - One 2GB DIMM in the lower slot.
2200 appliance (upgraded) - Two 2GB DIMMs, one in the lower and one
in the upper slot. Total RAM 4GB.
2200B appliance - One 4GB DIMM in the lower slot.
To upgrade a 2200 appliance to a 4GB configuration:
Insert the additional 2GB DIMM in the upper slot.
To replace a DIMM:
1. Remove the old DIMM from the appliance.
2. Insert the new one.

5
Installing Memory DIMMs
Item
Description
1
Front panel ports
2
Hard disk drive
3
Fan
4
Memory socket with two DIMM slots

6
To remove a memory DIMM from the appliance:
1. Find the DIMM memory socket on the system board.
The basic memory configuration of the appliance ships with one DIMM
installed.
2. Using your index fingers, press on the white retaining clips outward.
3. Remove the DIMM from the memory socket.

7
To insert memory DIMMs in the appliance:
1. Find the DIMM memory socket on the system board.
2. Align the DIMM diagonally to the lower memory socket.
Note - The top of the DIMM is smooth. The bottom edge has two
different-length sets of contacts, which connect to the slots on the
socket. Only touch the top of the DIMM. Pressing on other DIMM
components can damage the hardware.
3. Firmly press down on the DIMM and lock it into the lower socket.
The retaining clips move into the lock position as you press the DIMM
into the socket.
Important - Make sure that there are no leftover parts inside the
appliance.
4. For an upgraded 2200 appliance, repeat the previous steps for the
second DIMM.
5. Make sure the DIMM is installed correctly.
a) Replace the appliance cover without using the appliance cover
screws.
b) Connect the power cord to the appliance.
c) Turn on the appliance.
d) Make sure that the appliance starts correctly.
6. Use the appliance cover screws to secure the cover on the appliance.

8
Attaching the New Warranty Sticker
After you install the new DIMM, attach the new warranty sticker on the
appliance.
Important - Failing to attach the new warranty sticker correctly
will void the appliance warranty.
To attach the new warranty sticker:
1. Make sure that the appliance operates correctly.
2. Attach the new warranty sticker from the upgrade kit to the appliance.
The warranty sticker covers an appliance cover screw.
3. Clearly write this information on the sticker:
Date of upgrade
Current RAM memory configuration of the appliance