Chenbro Chassis RM21400 Installation and operating manual

RM21400 Chassis
Installation Reference Guide
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
1
RM21400 Chassis Installation Reference Guide

Copyright
This document is copyrighted, 2002, by Chenbro Micom Co., Ltd. and all rights
are reserved. Chenbro Micom Co., Ltd. reserves the right to make
improvements to the products described in this document at any time without
prior notice. Specifications are thus subject to change without notice.
No part of this document may be reproduced, copied, translated, or transmitted
in any form or by any means without the prior written permission of Chenbro
Micom Co., Ltd. Information provided in this document is intended to be
accurate and reliable. However, Chenbro Micom Co., Ltd., assumes no
responsibility for its use, nor for any infringements upon the rights of
3rd parties that may result from its use.
@Copyright Chenbro Micom Co., Ltd.
All rights reserved
Nov. 2002
Version 1.0
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
2
RM21400 Chassis Installation Reference Guide

Table of Contents
Chapter 1 General Information.........................................................................4
1.1 Specification........................................................................................4
1.2 Features..............................................................................................4
Chapter 2 SCSI Backplane Installation ............................................................6
2.1 Remove the top cover.........................................................................6
2.2 Remove the fan bracket......................................................................6
2.3 Remove the HDD drawer....................................................................7
2.4 Install the SCSI backplane assembly..................................................8
2.5 Connect LED and switch wires ......................................................... 11
2.6 Reattach the fan bracket and top cover ............................................16
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
3
RM21400 Chassis Installation Reference Guide

Chapter 1 General Information
1.1 Specification
Model Name RM214
Standard EIA-RS310D
M/B Form Factor ATX/Extended ATX
CPU Support DP Xeon/AMD Athlon
Dimension (D x W x H) 610mm x 430mm x 88.1mm
24" x 16.9" x 3.47"
HDD Tray 6
5¼" 1 x 5¼" drive + Slim CD-ROM
Exposed 3½" 1 x 3½" drive + Slim FDD Drive Bays
Internal 3½" N/A
PSU Type 350W ~ 600W PSU
Slot Opening 3 or 6
Cooling subsystem
3 x 8cm middle fans
Optional 2 x 4cm rear fans
Optional CPU cooler
Indicators LEDs for Power ON/OFF,
HDD / LAN activity & fan failure
Switch Power ON/OFF & Alarm Reset
Riser card (option) 32-bit or 64-bit PCI
Backplane (option) Ultra 160 SCSI or ATA 100 IDE
Construction SGCC
Net weight 12kg (chassis only)
Cubic feet 4
20’ 200Container information
(Single packing) 40’ 424
1.2 Features
 Easy Installation & Maintenance
- Screw-less installation for slim CD-ROM and slim FDD
- 6 x 1" front access Ultra 160 Hot-Swap HDD trays
- Optional 32-bit active PCI and passive 64-bit PCI riser card
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
4
RM21400 Chassis Installation Reference Guide

- Compliance with Dual Intel Xeon or Dual AMD MP Server boards
 Validated Thermal Solution
- Optional 4cm fan on rear panel for pulling out heated air efficiently.
 System Monitoring
- Buzzer alarm for Fan failure and overheat warning
- Support Alarm reset
 Application Strength
- Designed for high density front end server
- Ideal for NAS and RAID application and also for general purpose
server
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
5
RM21400 Chassis Installation Reference Guide

Chapter 2 SCSI Backplane Installation
2.1 Remove the top cover
1 Remove three screws on top cover.
2 Push top cover backward and life off the top cover.
3
2.2 Remove the fan bracket
1 Remove two screws on left & right side of fan bracket.
2 Lift off the fan bracket from chassis.
3 Set the fan bracket and screws aside for reattachment later.
2
1
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
6
RM21400 Chassis Installation Reference Guide

2.3 Remove the HDD drawer
1 Push the blue door lock to right-hand side; the handle will be release
automatically.
2
1
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
7
RM21400 Chassis Installation Reference Guide
2 Use the handle to pull HDD drawer out a little bit.

2
1
3 Repeat the same operation for the other 5 drawers.
4 Rear view of HDD trays.
2.4 Install the SCSI backplane assembly
1. Insert the SCSI backplane assembly into chassis.
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
8
RM21400 Chassis Installation Reference Guide

2. Check whether the SCSI bracket assembly is installed properly.
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
9
RM21400 Chassis Installation Reference Guide

3. Fasten the screws to fix the SCSI backplane assembly.
4. Push the HDD drawers back to drive trays.
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
10
RM21400 Chassis Installation Reference Guide

2.5 Connect LED and switch wires
There is one 2 x 9 pin connector on left-bottom side on SC SI backplane. This
connector provides several LED and switch connections for devices. The detail
pin definition is listed below.
Pin 1 Device 1 Power LED - Pin 2 Device 1 Power LED +
Pin 3 Device 1 Access LED + Pin 4 Device 1 Access LED -
Pin 5 Device 2 Power LED - Pin 6 Device 2 Power LED +
Pin 7 Device 2 Access LED + Pin 8 Device 2 Access LED -
Pin 9 Device 3 Power LED - Pin 10 Device 3 Power LED +
Pin 11 Device 3 Access LED + Pin 12 Device 3 Access LED -
Pin 13 Fail LED - Pin 14 Fail LED +
Pin 15 N/A Pin 16 N/A
Pin 17 Reset - Pin 18 Reset +
1. Check the pin number of “Reset SW” on connector.
Pin 1 Device 1 Power LED - Pin 2 Device 1 Power LED +
Pin 3 Device 1 Access LED + Pin 4 Device 1 Access LED -
Pin 5 Device 2 Power LED - Pin 6 Device 2 Power LED +
Pin 7 Device 2 Access LED + Pin 8 Device 2 Access LED -
Pin 9 Device 3 Power LED - Pin 10 Device 3 Power LED +
Pin 11 Device 3 Access LED + Pin 12 Device 3 Access LED -
Pin 13 Fail LED - Pin 14 Fail LED +
Pin 15 N/A Pin 16 N/A
Pin 17 Reset - Pin 18 Reset +
2. Plug “Reset SW” connector into pin 17 & 18 on connector.
3. Plug another “Reset SW” connector into another SCSI backplane.
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
11
RM21400 Chassis Installation Reference Guide

4. Check the pin number of “Fail LED” connector.
Pin 1 Device 1 Power LED - Pin 2 Device 1 Power LED +
Pin 3 Device 1 Access LED + Pin 4 Device 1 Access LED -
Pin 5 Device 2 Power LED - Pin 6 Device 2 Power LED +
Pin 7 Device 2 Access LED + Pin 8 Device 2 Access LED -
Pin 9 Device 3 Power LED - Pin 10 Device 3 Power LED +
Pin 11 Device 3 Access LED + Pin 12 Device 3 Access LED -
Pin 13 Fail LED - Pin 14 Fail LED +
Pin 15 N/A Pin 16 N/A
Pin 17 Reset - Pin 18 Reset +
5. Plug “LED” connector into pin 13 & 14. The black wire indicates the
ground pin of LED.
6. Plug another “LED” connector into another SCSI backplane.
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
12
RM21400 Chassis Installation Reference Guide

7. Check the pin numbers of HDD LED connectors.
Pin 1 Device 1 Power LED - Pin 2 Device 1 Power LED +
Pin 3 Device 1 Access LED + Pin 4 Device 1 Access LED -
Pin 5 Device 2 Power LED - Pin 6 Device 2 Power LED +
Pin 7 Device 2 Access LED + Pin 8 Device 2 Access LED -
Pin 9 Device 3 Power LED - Pin 10 Device 3 Power LED +
Pin 11 Device 3 Access LED + Pin 12 Device 3 Access LED -
Pin 13 Fail LED - Pin 14 Fail LED +
Pin 15 N/A Pin 16 N/A
Pin 17 Reset - Pin 18 Reset +
8. Plug HDD LED cables into connectors properly. The green wire
should be at the upper side. The LED cables can be separated to
three groups. Each group contains one yellow LED (HDD access)
and one green LED (power).
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
13
RM21400 Chassis Installation Reference Guide

9. Plug the LED with red wire to the lowest LED len.
10. Plug the green LED with green wire to the second lowest LED len.
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
14
RM21400 Chassis Installation Reference Guide

11. Repeat step 9 & 10 till all LED are installed properly.
12. Use the same way to install the LED on another SCSI backplane. Till
now, the installation of LED is completed.
13. Plug the power connectors to SCSI backplane.
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
15
RM21400 Chassis Installation Reference Guide

14. Plug the power connectors for another SCSI backplane.
15. Attach the SCSI cable to the unused SCSI connector.
2.6 Reattach the fan bracket and top cover
1. Plug two of the fan power connectors on fan bracket onto SCSI
backplane. The left fan connector should be connected to M/B.
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
16
RM21400 Chassis Installation Reference Guide

2. Reattach the fan bracket and arrange the cables properly.
3. Fasten the screws that are detached in section 2.2.
4. Put the top cover back and fasten the screws. Please check section
2.1 for detail locations of screws. The installation of SCSI backplane
is finished now.
1
2
Chenbro Micom CO., LTD.
15Fl., No. 150, Jian Yi Road, Chung Ho City,
Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
www.chenbro.com.tw
17
RM21400 Chassis Installation Reference Guide