CHERUBINI Domotic TX User manual

A530065
ISTRUZIONI - INSTRUCTIONS - EINSTELLANLEITUNGEN
INSTRUCTIONS - INSTRUCCIONES
I
GB
D
F
E
TX DOMOTICO
DOMOTIC TX
DOMOTIC TX SENDER
TX DOMOTIQUE
TX DOMÓTICO

1 BLUE
2 BROWN
3 RED
4 YELLOW
5 GREEN
APPLICATION TX DOMOTIC
8
Domotic control unit / Timer
Receiver
A530065
ENGLISH
Push-button
UP/DOWN
with
interlocking
Garda RX
Wave RX
Wave RX V25
Senso RX
Tronic RX
Clima RX
Clima Plus RX
Garda
Roll
Ocean
Micro

9
TECHNICAL SPECIFICATION
- Power supply 230 Vac
- Power consumption 1,5 W
- Transmission frequency 433,92 MHz
- Decoder system Rolling code
- Modulation AM/ASK
- Operating range in open spaces 150 m
- Operating temperature -10°C +55°C
- Dimensions (excluding wiring) 40 x 40 x 20 mm
- Weight 80 g
ENGLISH
GUARANTEE
Failure to comply with these instructions annuls CHERUBINI’s responsibilities and
guarantee.
EU DECLARATION OF CONFORMITY
CHERUBINI S.p.A. declares that the product is in conformity with the relevant Union
harmonisation legislation:
Directive 2014/53/EU,
Directive 2011/65/EU.
The full text of the EU declaration of conformity is available upon request at the
following website: www.cherubini.it.

10
ELECTRICAL CONNECTIONS
ATTENTION!
All installations and electrical
connections must be carried
out by qualied and competent
person.
ENGLISH
KEY TO SYMBOLS
LED
SET
short motor
rotation in one
direction
long motor rotation
in other direction
double short
rotation
Disconnect the
power supply
Power up
SET
Press button
SET
Press button A
A
Press buttons A and B
at the same time
+
A B
GIRO
Down
Stop
Up
A
B
C
Skipper
A
B
C

11
OPERATING MODES
ENGLISH
WIRING DIAGRAM
The domotic transmitter has two operating modes:
- STANDARD MODE: suitable for connection to a domotic control unit.
Commands are:
Up: Contact maintained longer than 1 second between up and common.
Down: Contact maintained longer than 1 second between down and common.
Stop: No contact between up/down and common.
Activating the tilting mode (only with Clima RX and Clima Plus RX motors): Contact
maintained longer than 1 second between up, down and common.
Note: the command transmission occurs after contact is maintained for longer
than 1 second.
- ADVANCED MODE: Suitable for direct connections to wall-mounted selectors (instable
type preferably).
Commands are:
Up: Contact between up and common.
Down: Contact between down and common.
Stop: New contact on the previously selected direction.
Activating the tilting mode (only with Clima RX and Clima Plus RX motors): Quick
sequence - no longer than 0,5 seconds - between the up and down with the common.
Note for both modes: the radio transmission of each command will be repeated
three times - within few seconds - in case of disturbed reception.
DOMOTIC
TX
BLUE
BROWN
RED (COMMON)
YELLOW (UP)
GREEN (DOWN)
- DOMOTIC CONTROL UNIT
- UP/DOWN SELECTOR
Garda RX
Wave RX
Wave RX V25
Senso RX
Tronic RX
Clima RX
Clima Plus RX

12
SETTING THE FIRST REMOTE CONTROL
SETTING THE DOMOTIC TRANSMITTER
This operation can only be performed when the motor is new, or after a total delete of
the memory.
T1: First remote control to be set
To associate the transmitter to a motor, a remote control must be already memorised on
the motor. The setting sequence is the following:
Tn: Already programmed remote control
During this step, power up only one motor at time!
T1T1 T1 (2 sec)
TnTn (2 sec)
SET
ENGLISH
The domotic transmitter is factory set to operate in standard mode.
The mode can be changed from standard to advanced mode and vice versa with the
following command sequence:
- Disconnect the power supply, wait 2 seconds.
- Hold the SET button down and power up.
- Release the set button as soon as the LED blinks (around 2 sec).
When the Domotic TX comes on it indicates the mode set:
- One LED blink: standard mode
- Two LED blinks: advanced mode.
2 sec
2 sec
SET SET
LED LED
3
MODE CHANGING
+
A B B B
+
A B B

13
DOMOTIC TX INSTALLATION EXAMPLE
- You can use an existing wall socket to command a motor, without having to add extra
wires to the wiring.
- Thanks to its small size (40x40x20), you can insert the Domotic TX in a built-in socket.
- You can use switches of existing kind, so as not to change the look of the living space.
ENGLISH
DELETING DOMOTIC TRANSMITTER
To delete the transmitter from the motor, an already programmed remote control must be
used. The deleting sequence is the following:
Tn: Already programmed remote control
TnTn (2 sec)
SET
+
A B
A

Rev. 4 05/2018 - Cod: A4518_6B40
CHERUBINI Deutschland GmbH
Siemensstrasse, 40 - 53121 Bonn - Deutschland
Tel. [phone] / 35 | Fax [phone]
[e-mail] | www.cherubini-group.de
CHERUBINI France S.a.r.l.
ZI Du Mas Barbet
165 Impasse Ampère
30600 Vauvert -France
Tél. [phone] | Fax [phone]
[e-mail] | www.cherubini.fr
CHERUBINI Iberia S.L.
Avda. Unión Europea 11-H
Apdo. 283 - P. I. El Castillo
03630 Sax Alicante - Spain
Tel. [phone] | Fax [phone]
[e-mail] | www.cherubini.es
CHERUBINI S.p.A.
Via Adige 55
25081 Bedizzole (BS) - Italy
Tel. [phone] | Fax [phone]
[e-mail] | www.cherubini.it