INOR APAQ C130 TC User manual

MEASURE OF SUCCESS
USER INSTRUCTIONS
Programmable
2-wire Transmitter
for Thermocouple
The user instruction must be read prior to adjustment and/or installation.
All information subject to change without notice.
© INOR 10/2021 - 4008975501 - MA APAQ C130 TC R01 en
GENERAL INFORMATION
APAQ C130TC is a low cost, non-isolated, easy-to-use 2-wire transmitter, for
thermocouple input, intended to be used in industrial environment.
The transmitter is configured from a mobile device via NFC
communication, by using the app INOR Connect. Inor Connect is available
for free download on App Store, Google Play Store and Huawei AppGallery.
C130TC
MEASURE OF SUCCESS
DATA (short form)
CONFIGURATION
Input 2-wire connection
TC type B - Pt30Rh-Pt6Rh (IEC 60584) 0...+1820 °C / +32...+3308 °F
TC type E - NiCr-CuNi (IEC 60584) -270…+1000 °C / -454...+1832 °F
Input impedance 10 MΩ
Maximum wire loop resistance
Output
Internal or fixed
Sensor failure indication Upscale (≥21.0 mA) or downscale (≤3.6 mA)
NAMUR Compliance Current limitations and failure currents acc.
Adjustable filtering level
Ambient temperature
Storage and operation -40 to +85 °C / -40 to +185 °F
Galvanic isolation None
Power supply 6 to 32 VDC
Accuracy
Mounting DIN B-head or larger
Conguration App INOR Connect via NFC™
Factory settings
Input 0 to 1000 °C
Output 4 to 20 mA
Sensor error indication Upscale
This product should not be mixed with other kind of scrap, after usage.
It should be handled as an electronic/electric device.
www.inor.com, www.inor.se
INOR Process AB, PO Box 9125, SE-200 39 Malmö, Sweden,
Phone: [phone], Fax: [phone], E-mail: [e-mail]
INOR Transmitter OY, Unikkotie 13, FI-01300 Vantaa, Finland,
Phone:[phone], Fax: [phone], E-mail: myynti@inor.
INOR Transmitter GmbH, Am See 24, D-47279 Duisburg, Germany,
Phone: [phone], Fax: [phone], E-mail: [email protected]
KROHNE Temperature Division INOR, 55 Cherry Hill Drive,
Beverly, MA 01915, United States
Phone: [phone], Fax: [phone], E-mail: [email protected]
1.
TC type J - Fe-CuNi (IEC 60584)
TC type K - NiCr-NiAl (IEC 60584)
TC type N - NiCrSi-NiSi (IEC 60584)
TC type R - Pt13Rh-Pt (IEC 60584)
TC type S - Pt10Rh-Pt (IEC 60584)
TC type T - Cu-CuNi (IEC 60584)
-210…+1200 °C / -346...+2192 °F
-270…+1300 °C / -454...+2372 °F
-270…+1300 °C / -454...+2372 °F
-50...+1750 °C / -58...+3182 °F
-50…+1750 °C / -58...+3182 °F
-270…+400 °C / -454...+752 °F
Cold Junction Compensation
In-head transmitter (TC sensor): 5 kΩ
4-20 mA, temperature linear
Warm-up time After a max. 20 minutes the accuracy
specifications are reached
(due to the internal cold junction)
RoHS, China RoHS Directive: 2011/65/EU and 2015/863/EU
Harmonized standard: EN IEC 63000
China RoHS 2
TC type R, S, T
TC type E, J, K
TC type N (-100...+1300 °C )
Max. of ±1 °C or ±0.2% of span
Max. of ±1 °C or ±0.2% of span
TC type N (-270...-100 °C )±2.0 °C / ±3.6 °F
2.
Launch the app by clicking on the App icon or holding
your mobile device against the transmitter on the part
of the device where NFC is located (only possible with
Android).
Click on “Read Configuration” and hold your mobile
device against the transmitter as explained in the
first section.
a. Sensor type
b. Measuring range
c. Upscale ordownscale sensor error indication
d. Filter level
e. TAG-number
f. Password
3.
4.
Type K
TC type B
Max. of ±2.0 °C or ±0.2% of span
to NAMUR NE 43
0.4 to 26 sec.
See Data Sheet
Max. of ±3.6 °F or ±0.2% of span
Max. of ±1.8 °F or ±0.2% of span
Max. of ±1.8 °F or ±0.2% of span
Once you have set the desired values in the app, you transfer it to the
transmitter by clicking the transfer button and holding the mobile device
against the transmitter until a green check box appears confirming that
the transfer has been completed.
CJC accuracy Typical ±1 °C / ±1.8 °F (max ±3 °C /
±5.4 °F) within ambient temperature range
Before making a configuration of APAQ C130TC you need to do following:
Make sure that you have a mobile device with NFC communication
activated. Download the app INOR Connect to your mobile device.
Required versions:
iOS: iOS 13 or later and Android:
Iphone 7 or later for NFC Android 4.4 or later
Configuration procedure:
In the app you can edit the following:

INSTALLATION
MOUNTING
Head mounting kit
ORDERING INFORMATION
LIMITED WARRANTY
APAQ C130TC 70C1300211
Head mounting kit 70ADA00017
DIN-rail Adapter + Screw (10 pcs) 70ADA00027
OUTPUT LOAD DIAGRAM
53/2.08
DIN-rail
Adapter
mm/inches
APAQ C130TC is designed to fit inside connection heads type DIN B
or larger. The larger center hole, diameter 7 mm/0.28 inch,
facilitates the pulling through of the sensor leads or an insert tube,
greatly simplifying the mounting procedure.
Connect input, output and power supply acc. to
“CONNECTIONS”. A convinient way to install the transmitter is
to use the INOR mounting kits for in-head and DIN rail mounting.
In order to minimize measuring errors make sure the connecting
screws are tightened enough, 0.5-0.6 Nm.
!
CONNECTIONS
INOR Process AB, or any other aliated company within the Inor Group (hereinafter
jointly referred to as ”Inor”), hereby warrants that the Product will be free from
defects in materials or workmanship for a period of ve (5) years from the date of
delivery (”Limited Warranty”). This Limited Warranty is limited to repair or replace-
ment at Inor’s option and is eective only for the rst end-user of the Product. Upon
receipt of a warranty claim, Inor shall respond within a reasonable time period as to
its decision concerning:
1 Whether Inor acknowledges its responsibility for any asserted defect in
materials or workmanship; and, if so,
2 the appropriate cause of action to be taken (i.e. whether a defective
product should be replaced or repaired by Inor).
This Limited Warranty applies only if the Product:
1 is installed according to the instructions furnished by Inor;
2 is connected to a proper power supply;
3 is not misused or abused; and
4 there is no evidence of tampering, mishandling, neglect, accidental damage,
modication or repair without the approval of Inor or damage done to
the Product by anyone other than Inor.
This Limited Warranty is provided by Inor and contains the only express war-
ranty provided.
INOR SPECIFICALLY DISCLAIMS ANY EXPRESS WARRANTY NOT
PROVIDED HEREIN AND ANY IMPLIED WARRANTY, GUARANTEE
OR REPRESENTATION AS TO SUITABILITY FOR ANY PARTICULAR
PURPOSE, PERFORMANCE, QUALITY AND ABSENCE OF ANY HID-
DEN DEFECTS, AND ANY REMEDY FOR BREACH OF CONTRACT,
WHICH BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION,
OPERATION OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING,
INCLUDING IMPLIED WARRANTIES OF MER-CHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. EXCEPT AS PROVIDED HER-
EIN, INOR FURTHER DISCLAIMS ANY RESPONSIBILITY FOR LOSSES,
EXPENSES, INCONVENIENCES, SPECIAL, DIRECT, SECONDARY OR
CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE
OF THE PRODUCT.
Products that are covered by the Limited Warranty will either be repaired or replaced
at the option of Inor. Customer pays freight to Inor, and Inor will pay the return
freight by post or other “normal” way of transport. If any other type of return freight
is requested, customer pays the whole return cost.
The transmitters are delivered with either a default factory setting or
congured according to customer’s specication.
Maximum load depending on power supply Formula for
the max. permissible output load for APAQ C130TC:
Load
R =(U-6)/0.022
DIMENSIONS
TC Connection
How to mount on DIN-rail Adapter
Step 1
Step 2
10/0.39
T/C
Input
Output