Cheyenne HAWK SPIRIT User manual

HAWK
PE
N
®
Gebrauchsanleitung
Operating instructions
Gebruiksaanwijzing
Instructions
Istruzioni per l‘uso
Instrucciones de uso
Manual de instruções
Oδηγίες
Opskrift
Bruksanvisning
Ohjeet
Instrukcja obsługi
Instrukce
Navodila nt pl za uporabo
Utasítás
инструкции
说明
HAWK spirit
HAWK thunder

2 Cheyenne HAWK spirit & HAWK thunder
8
7
1
2
34
5
6
A
B
7
56
HAWK SPIRIT (A) HAWK THUNDER (B)

Cheyenne HAWK spirit & HAWK thunder
Operating instructions
Contents
1 About these operating
instructions......................................... 29
1.1 Display of warning notices .... 29
1.2 Symbol used in these operating
instructions ................................ 30
2 Important safety notices................. 30
2.1 General safety information.... 30
2.2 Product-dependent safety
information................................. 30
2.3 Important hygiene and safety
regulations.................................. 31
2.4 Contra-indications.................... 31
2.5 Side-eects................................ 32
2.6 Required qualification ............. 33
2.7 Intended use............................... 33
2.8 Symbols on the packaging .... 34
3 Scope of delivery............................... 34
4 HAWK SPIRIT and HAWK THUNDER
product information ......................... 35
4.1 Technical data............................ 35
4.2 Operating conditions................ 35
4.3 Accessories................................ 35
5 Preparing the HAWK SPIRIT or
HAWK THUNDER for use................. 36
5.1 Disinfecting equipment........... 36
5.2 Assembling and disassembling
the handle and drive................ 37
5.3 Fitting the protective sleeve.. 37
5.4 Connecting the power unit..... 39
5.5 Safety cartridge replacement41
5.6 Checking equipment................ 42
6 Using the HAWK SPIRIT or
HAWKTHUNDER................................ 43
6.1 Setting the needle protrusion43
6.2 Setting the piercing
frequency.................................... 43
6.3 Loading with ink........................ 44
7 Cleaning and maintaining the
HAWKSPIRIT or HAWKTHUNDER44
7.1 Material compatibilities.......... 45
7.2 Disinfecting surfaces............... 45
7.3 Cleaning surfaces..................... 46
7.4 Cleaning handle in an
ultrasonic bath .......................... 46
7.5 Sterilizing handle in
an autoclave............................... 46
8 Transport and storage conditions 46
9 Disposal of equipment..................... 47
10 For questions or problems............. 47
11 Manufacturer declarations............. 48
11.1Warranty declaration............... 48
11.2Declaration of Conformity...... 49
28
HAWK
PE
N
®
HAWK spirit
HAWK thunder
EN
English
Version 2.0
04/2016
Translation of the
original operating
instructions.
The original
operating
instructions were
written in German.

29EN
Cheyenne HAWK spirit & HAWK thunder
1 About these operating
instructions
These operating instructions apply to the
Cheyenne HAWK SPIRIT and HAWKTHUN-
DER tattooing machines and to their
accessories. They contain important infor-
mation about how to operate and maintain
these products safely and in the intended
manner.
These operating instructions do not con-
tain all of the information needed for safe
operation of the tattooing machines and
their accessories. Note the following addi-
tional documents:
Operating instructions for the Cheyenne
Power Unit and/or an external power unit
and, if applicable, a foot switch
Information about safety cartridges and
tattoo inks
Safety data sheets about disinfectants
and cleaning agents
Health and safety information and statu-
tory provisions relating to tattooing
1.1 Display of warning notices
Warning notices draw attention to the risk
of personal injury and damage to materials
and are structured as follows:
SIGNAL WORD
Type of hazard
Consequences
!Remedy
Element Meaning
Indicates a risk of injury
Signal
word
Specifies the severity of the
hazard (see following table)
Type of
hazard
Gives the type and source of
the hazard
Conse-
quences
Describes potential conse-
quences of non-compliance
Remedy Indicates how to avoid
ahazard
Signal
word Meaning
Warning Indicates a hazard that can
lead to death or to serious
injury if the hazard is not
avoided
Caution Indicates a hazard that can
lead to minor to relatively
serious injury if the hazard is
not avoided

30 EN Cheyenne HAWK spirit & HAWK thunder
Signal
word Meaning
Attention Indicates potential risks to
the environment, property
or the tattooing equipment if
this hazard is not avoided.
1.2 Symbol used in these operating
instructions
Symbol Meaning
!Call for action
List point
-List sub-point
2 Important safety
notices
2.1 General safety information
!Read these operating instructions care-
fully and completely.
!Keep these operating instructions in
areadily accessible location for everyone
who uses, cleans, disinfects, sterilizes,
stores or transports the HAWK SPIRIT
and HAWK THUNDER.
!When transferring the HAWK SPIRIT
or HAWK THUNDER to another person,
always include these operating instruc-
tions.
!Follow the safety regulations applicable
to tattooing in your country. Keep your
tattoo studio in a hygienic, clean condition
and provide sucient lighting.
!Use the HAWK SPIRIT or HAWK THUNDER,
its accessories and the power unit as
well as all connecting cables in perfect
technical condition.
!Only use genuine safety cartridges, ac-
cessories and spare parts from Chey-
enne.
2.2 Product-dependent safety
information
!Never modify your HAWK SPIRIT or
HAWKTHUNDER; the safety cartridges
or other accessories.
!Prevent fluids from entering the drive
unit.
!During the tattooing process, protect
the drive and its connecting cables with
a protective sleeve (see chapter 5.3 on
page 37). Also protect the power unit
with a plastic sheet.
!If you are not using your HAWK SPIRIT or
HAWK THUNDER, switch it oand place
it in a location so that it cannot fall down.
!Observe the technical data (chapter 4.2
on page 35) and observe the operat-
ing conditions (chapter 4.1 on page 35)

31EN
Cheyenne HAWK spirit & HAWK thunder
and transport and storage conditions
(chapter 8 on page 46).
!HandovertheHAWKSPIRITorHAWKTHUNDER
to a specialist retailer for inspection if it exhibits
any external signs of damage or if it does not
function in the usual manner.
2.3 Important hygiene and safety
regulations
To prevent infectious diseases resulting
from tattooing being transmitted to the
customer or to the tattoo artist:
!Before use, follow the steps required to
disinfect the equipment (see chapter 5.1
on page 36).
!During the tattooing process, wear
disposable nitrile or latex gloves and
disinfect them before use.
!Before applying a tattoo, clean the
aected areas of the customer's skin
with a mild cleaning and disinfectant
agent. When selecting an appropriate
disinfectant,take note of the applicable
regulations in your country.
!For every customer and each ink,
always use new, sterile-packaged safety
cartridges. Before each usage, ensure
that the packaging is undamaged and
that the use-by date has not passed.
!Dispose of used or defective safety car-
tridges in a sharps container (safety box)
in accordance with the regulations appli-
cable in your country.
!Prevent safety cartridges coming into
contact with contaminated objects,
e.g.clothing. Dispose of contaminated
safety cartridges immediately.
!Always use dermatologically safe inks
designed specifically for tattooing.
!Avoid contact with freshly tattooed skin.
Protect freshly tattooed areas of skin
from dirt and from exposure to UV light
and sunlight.
!Checkona regularbasisiftheHAWKSPIRIT
or HAWK THUNDER has become visibly
contaminated by the return flow of inks
or bodily fluids. If this has happened,
in addition to regular disinfection, you
must perform all the steps described in
chapter “Cleaning and maintaining the
HAWK SPIRIT or HAWKTHUNDER” (see
chapter 7 on page 44).
2.4 Contra-indications
Tattooing is not permitted in case of the
following:
Haemophilia/blood vessel conditions
Uncontrolled diabetes mellitus
Treatment of areas of skin with dermatitis
complaints (e.g. skin tumors, celoids or
extreme celoid tendency, solar ceratosis,
warts or moles)

32 EN Cheyenne HAWK spirit & HAWK thunder
Feverish infections and infectious diseas-
es such as hepatitis conditions of types
A, B, C, D, E or F or HIV
Immune system diseases
Epilepsy
Acute cardio-vascular problems
Under the influence of alcohol or drugs
In the following cases, tattooing cannot
be performed until such time as normal
health is restored:
Acute dosages of anticoagulants (e.g. Warfarin,
Heparin, Phenprocoumon or Salicic acid)
Acute chemotherapy, radiotherapy or
high-dosage corticosteroid therapy
Systemic infections or acute local skin
infections (e.g. with the herpes virus)
Allergy to topical anesthetics (local an-
esthesia)
Pregnancy and breast-feeding
Temporary locally restricted contra-
indications exist in the following cases:
Eczema, exanthema or open wounds
Acute conjunctivitis
Scars less than six months old
Areas of skin after plastic surgery treat-
ment less than twelve months previously
Areas of skin after filler injections less
than six months previously
If there is the slightest doubt about cus-
tomer safety, do not commence treatment
or terminate treatment immediately and
seek medical attention.
The treatment must be terminated imme-
diately in the event of:
Excessive sensations of pain
Excessive release of fluids from the
wound
Fainting / dizziness
2.5 Side-eects
In a few cases, the tattooing process may
result in minor side eects.
!Inform the customer about all risks and
about the side-eects described below.
Frequent:
Pain on the day after tattooing
Inflammation reactions, haematomas,
erythema and oedema in the first three
to five days after tattooing
Skin irritations (e.g. itching or heating),
which normally wear oduring the first
12 to 48 hours after tattooing
Rare:
Hyper-pigmentation with body's own pig-
ments, in particular on dark skin types,
but that disappear completely a few
weeks later
Formation of scabs, small pimples or
skin eruptions if skin is not cleaned care-
fully after tattooing

33EN
Cheyenne HAWK spirit & HAWK thunder
Retinoid reaction (slight irritation up to
peeling of skin)
Possible heating of the tattooed area
when exposed to PET and MRT radiation
Contact allergy to ink pigments or aller-
gic reactions to other components of the
aseptic ink
Furthermore, the following problems can
occur in response to tattooing:
Ink shade dierences
Pigment loss
2.6 Required qualification
The HAWK SPIRIT and HAWK THUNDER
may only be used by people who have
acquired the following knowledge:
Basic knowledge of the tattooing process,
in particular correct insertion depth and
frequency
Knowledge of the hygiene and safety
regulations (see chapter 2.3 on page 31)
Knowledge of the impact of tattoo ink be-
low the skin
Knowledge of the risks and side-eects
(see chapters “2.4 Contra-indications”
on page31 and “2.5 Side-eects” on
page32).
2.7 Intended use
The HAWK SPIRIT and HAWK THUINDER
are professional tattooing machines for
the application of tattoos to the human
skin in dry, clean and smoke-free environ-
ments, and under hygienic conditions. They
must be prepared, used and maintained in
the manner described in these operating
instructions. In particular, the applicable
provisions for workplace layout must be
observed, and all safety cartridges used
must be sterile.
Intended use also includes thoroughly reading
andunderstandingthese operatinginstructions,
in particular the chapter “2 Important safety
notices”.
Unintended use is defined as using the
HAWK SPIRIT, HAWK THUNDER or their
accessories in a way not described in these
operating instructions, or failing to comply
with its operating conditions. In particular
the tattooing of mucous membranes, or
the eyes, and the tattooing of minors is
prohibited.

34 EN Cheyenne HAWK spirit & HAWK thunder
2.8 Symbols on the packaging
The following symbols are found on the
HAWK SPIRIT, HAWK THUNDER and acces-
sory packages:
Symbol Meaning
Satisfies the requirements
of directives 2006/42/EC
(machinery directive) and
2004/108/EC (EMC directive)
Observe instructions for use!
Manufacturer
Date of manufacture
Catalogue number
NSerial number
Batch code
Sterilized with ethylene oxide
Use-by date
Attention!
Temperature limit
Humidity limit
Store in a dry place
Fragile
Cannot be use if packaging is
damaged
Do not reuse!
Dispose of properly as used
electronic equipment!
3 Scope of delivery
See insert.

35EN
Cheyenne HAWK spirit & HAWK thunder
4 HAWK SPIRIT and HAWK
THUNDER product information
The HAWK SPIRIT and HAWK THUNDER are
high-performance tools. They have a sig-
nificantly higher piercing force and piercing
frequency than conventional tools. Despite
this added performance, they are consider-
ably quieter with less vibration.
The HAWK SPIRIT is an all-around tattooing
machine with a shorter needle stroke. It is
especially well-suited for filling and shad-
owing. The HAWK THUNDER has alonger
needle stroke is especially well-suited for
lines and contours.
4.1 Technical data
SPIRIT THUNDER
Nominal voltage 6 to 12.5V DC
Power intake 2.5W (max. 5W)
Starting current
for max. 30 ms 1.9A 2.5A
Piercing
frequency 60 to 160 Hz
Stroke 2.5 mm 4 mm
Needle
protrusion 0 to 4 mm
Electrical
connection 3.5 mm jack
Drive Precision motor – DC
Operating mode Continuous operation
Dimensions
including handle
Approx. 110 x 57 x
28 mm
Weight including
handle Approx. 130 g
4.2 Operating conditions
Ambient
temperature
+10 to +35°C
+50 to +95°F
Relative
humidity 30 to 75%
Air pressure 700 to 1070hPa
4.3 Accessories
The following accessories can be pur-
chased from your local specialist retailer:
Cheyenne handles
Cheyenne safety cartridges
Cheyenne Power Units
Cheyenne foot switch
Cable adapters
Protective sleeves for the handle
Protective sleeves for the drive and con-
nection cable

36 EN Cheyenne HAWK spirit & HAWK thunder
5 Preparing the HAWK SPIRIT or
HAWK THUNDER for use
ATTENTION
Damage from condensate
If the HAWK SPIRIT or HAWK THUNDER
is exposed to significant variation in tem-
perature, e.g. during transport, conden-
sate can form inside which can damage
the electronics.
!Ensure that the HAWK SPIRIT or HAWK
THUNDER has reached ambient tem-
perature before using it. If it was ex-
posed to high temperature fluctuations,
wait for at least 3 hours for every 10°C
of temperature dierence before put-
ting it into operation.
!Only use the HAWK SPIRIT or HAWK
THUNDER at ambient temperatures of
+10 to +35°C.
5.1 Disinfecting equipment
ATTENTION
Damage to drive caused by fluid
If disinfectant gets inside the drive, this
can corrode the electrical and mechani-
cal components.
!Never immerse the drive in disinfectant.
ATTENTION
Product damage caused by non-
approved disinfectants
Disinfectants that are not compatible
with the materials of the product can
damage its surface.
!Always use disinfectants that are
approved, i.e. that comply with stipula-
tions in your country.
!Note the list of recommended disinfec-
tants in chapter “7.1 Material compat-
ibilities” on page45.
!Switch othe voltage supply to your
HAWK SPIRIT or HAWK THUNDER.
!Check on a regular basis if the HAWK
SPIRIT or HAWK THUNDER has become
heavily contaminated by the return flow
of inks or bodily fluids. In such cases,
perform the steps described in chap-
ter “7 Cleaning and maintaining the
HAWK SPIRIT or HAWKTHUNDER” on
page44.
!Wipe down the connecting cables, the
drive and the handle with a soft cloth
moistened with disinfectant.

37EN
Cheyenne HAWK spirit & HAWK thunder
5.2 Assembling and disassembling
the handle and drive
Handles are available in dierent
diameters. The assembly procedure is the
same for each.
For assembly:
!Fit the piston (3) in the handle (1).
!Adjust the angle between the drive (4)
and index (2) so that your HAWK SPIRIT
or HAWK THUNDER is comfortable in
your hand.
The index marks the position of the upper
and lower part of the safety cartridge.
!Tighten the fixing nut(5) to the mechani-
cal stop without changing the adjusted
angle.
!Ensure that the index(2) does not turn
while you turn the handle. Tighten the
fixing nut as necessary.
For disassembly:
!Unscrew the fixing nut.
!Remove the handle from the drive.
The piston comes out of the handle.
5.3 Fitting the protective sleeve
CAUTION
Infection from contaminated protective
sleeve
Failure to replace the protective sleeve
for the handle can lead to a transmission
of illnesses.
2
3
4
1
5
2

38 EN Cheyenne HAWK spirit & HAWK thunder
!Use a new protective sleeve for the
handle for each customer.
ATTENTION
Damage to drive caused by fluid
If fluid gets inside the drive or on the
connection, this can corrode the electrical
and mechanical components.
!Always use one protective sleeve(1)
for the handle and a second protective
sleeve(2) for the drive and connection
cable as described below.
In order to fit the protective sleeve (1) on
the handle:
!If already inserted: Remove the safety
cartridge from the handle (see chapter
“5.5 Safety cartridge replacement” on
page41).
!Slide the protective sleeve (1) completely
over the connecting cable.
!Insert the safety cartridge (3) through the
hole of the protective sleeve (1) into the
handle (see chapter “5.5 Safety cartridge
replacement” on page41).
The safety cartridge fixes the protective
sleeve (1) and simultaneously seals the
opening.
1
2
1
13

39EN
Cheyenne HAWK spirit & HAWK thunder
In order to fit the protective sleeve (2) on
the connection cable and drive:
!If already inserted: Remove the connec-
tion cable from the HAWK SPIRIT or the
HAWK THUNDER.
!Cut oa section of protective sleeve of an
appropriate length.
!Slide this section of protective sleeve
completely over the connecting cable.
!Connect the connection cable (see the
next chapter).
!Pull the end of the protective sleeve(2)
completely over the HAWK SPIRIT or
HAWK THUNDER.
!Ensure that the two protective sleeves
overlap. For instance, fix them with
arubber band or adhesive film.
5.4 Connecting the power unit
CAUTION
Risk of short circuits and risk of mild
electric shocks
If cable or cable connection is visibly
damaged, there is a risk of electric shock
and damage to the electronics.
!Perform a visual inspection of the
HAWK SPIRIT or HAWK THUNDER and
the cable for signs of damage, e.g.
adefective cable connection.
!Never bend the connecting cable while
in operation.
!Observe the operating instructions for
the particular power unit.
CAUTION
Cables constitute a trip hazard
People can stumble over inappropriately
routed cables and get injured.
!Route all cables so that no-one can
stumble over them or pull them ac-
cidentally.
13 2

40 EN Cheyenne HAWK spirit & HAWK thunder
There are four ways to supply power to the
HAWK SPIRIT or HAWK THUNDER: 1. Connecting it to a Cheyenne Power
Unit with the connecting cable pro-
vided in the scope of delivery (recom-
mended)
2. Connection to a third-party power unit
with the 6.3mm jack and the cable
adapter supplied
3. Connection to a third-party power
unit with the cinch socket and anad-
ditional cable adapter
4. Connection to a third-party power unit
using the optional Y-cable adapter
with banana plug – The red banana
plug must be connected to the positive
terminal while the black banana plug
must be connected to the negative
terminal of the third-party power unit.
The third-party power unit must deliver
approx. 6 to 13V DC. If more than about
13V is connected to the HAWK SPIRIT
or HAWKTHUNDER, it will shut down
automatically.
!Connect the cinch socket of the con-
necting cable (supplied) to the DC power
connection of the HAWK SPIRIT or HAWK
THUNDER.
!Plug the cinch plug of the connecting
cable completely into the socket on the
tattoo machine power unit.
If you are using an third party power unit,
connect up its terminals correctly, as
described in the operating instructions of
the third party power unit.
1.
2.
3. 4.
Third-party power unit
PU

41EN
Cheyenne HAWK spirit & HAWK thunder
!Cover the power unit or the third party
power unit with a plastic sheet.
5.5 Safety cartridge replacement
WARNING
Risk of injury from needles
Injuries caused by contaminated needles
of the safety cartridges can lead to the
transmission of diseases.
!Only use original Cheyenne safety car-
tridges. The installed safety membrane
on these safety cartridges prevents the
ingress of ink into the drive, and also
prevents pathogens from entering the
appliance through the safety cartridge.
!Never hold the safety cartridge by its
tip or the bayonet connector.
!Switch othe HAWK SPIRIT or
HAWKTHUNDER before replacing the
safety cartridge.
!When removing a used safety cartridge,
ensure that no ink remnants can run
into the handle.
!Never push the needles out of the safe-
ty cartridge by hand.
!Check during the removal of a used
safety cartridge that the needles are
completely retracted into the safety
cartridge.
!Dispose of used safety cartridges that
are no longer required for the current
application (see chapter “9 Disposal of
equipment” on page47).
!The safety cartridges are supplied in
sterile packaging. Do not remove them
from their packaging until immediately
before you intend to use them.
!Always put down the HAWK SPIRIT
or HAWK THUNDER so that the safety
cartridge is not supporting it.
!Seek medical attention if injured by
acontaminated needle.

42 EN Cheyenne HAWK spirit & HAWK thunder
!Switch othe voltage supply to your
HAWK SPIRIT or HAWK THUNDER.
!Insert the safety cartridge in the opening
in the handle, as illustrated below.
The safety cartridge only fits in the
opening in two directions.
!Rotate the safety cartridge clockwise
approx. 45°.
The index (1) marks the position of the
upper (2) or lower part of the safety
cartridge.
!Check that the safety cartridge is firmly
seated.
!To remove the safety cartridge, turn it
counterclockwise and remove it from the
handle.
5.6 Checking equipment
!Conduct a visual inspection of the equip-
ment:
- Are there any visible signs of external
damage (e.g. bends in the connecting
cable or bent piston)?
- Are there any exposed cables?
-Are the safety cartridge and
theneedles correctly aligned?
!Switch one the HAWK SPIRIT or
HAWKTHUNDER and perform an audio
test: Can you hear any unusual operating
noises, or is the unit running loudly?
!If you detect anything unusual, refer to
chapters “10 For questions or problems”
and “11.1 Warranty declaration” on
page48.
!If the HAWK SPIRIT or HAWK THUNDER is
no longer operating safely, take it out of
service and consult your local specialist
retailer.
Approx. 45°

43EN
Cheyenne HAWK spirit & HAWK thunder
6 Using the HAWK SPIRIT or
HAWK THUNDER
6.1 Setting the needle protrusion
CAUTION
Risk of injury from excessive protrusion
of needle
A large needle protrusion permits a deep
piercing depth. If needle protrusion and
piercing depth are excessive, this can
damage the subcutaneous layer.
!Start with just a short length of needle
protruding.
!Switch on the power.
!Adjust the needle protrusion while the
HAWK SPIRIT or HAWK THUNDER is
switched on; to do this, turn the handle.
Turning clockwise increases the protru-
sion of the needle:
Turning counterclockwise reduces the
protrusion of the needle:
The needle protrusion changes by
approx. 0.1mm per detent.
!Ensure that the index does not turn while
you turn the handle.
6.2 Setting the piercing frequency
CAUTION
Risk of injury due to high piercing
frequency
If the piercing frequency is too high, the
skin can be cut.
!Always start at a low piercing frequen-
cy, e.g. 70.
+
Max.
-
Min.

44 EN Cheyenne HAWK spirit & HAWK thunder
!Switch on the power supply of the
Cheyenne power unit and/or third-party
power unit.
!Set an appropriate piercing frequency.
The piercing frequency must suit the
characteristics of the customer's skin,
the needle protrusion and piercing depth
when working, as well as the operating
speed.
With a Cheyenne Power Unit the piercing
frequency can be adjusted in 10 increments
using the arrow keys.
With a third-party power unit, the pierc-
ing frequency can be adjusted via the out-
put voltage: The permitted voltage range
of approx. 6 to 12.5V equates roughly to
a piercing frequency range of 60 to 170
needle insertions per second. 10V equates
to about 130 needle insertions per second
at idle speed. If the output voltage exceeds
about13V, the HAWK SPIRIT or HAWK
THUNDER switches oautomatically.
6.3 Loading with ink
!Immediately before use, dip the tip of the
safety cartridge in the desired color of ink
for 2 to 3 seconds with the unit running.
Avoid contact with the ink container.
The ink is picked up by the needles.
!Alternatively, the ink can be filled into
the opening on the safety cartridge using
asterile pipette. Never fill in too much
ink so that it is not ejected through the
opening.
7 Cleaning and maintaining
the HAWK SPIRIT or
HAWKTHUNDER
CAUTION
Risk of short circuits and risk of mild
electric shocks
If components of the HAWK SPIRIT or
HAWK THUNDER are dismantled and
cleaned while still powered, there is
arisk of mild electric shock and damage
to the electronics in the drive unit.
!Switch othe voltage supply to your
HAWK SPIRIT or HAWK THUNDER be-
fore you begin with cleaning and main-
tenance work.
ATTENTION
Damage to drive caused by fluid
If cleaning fluid or disinfectant gets inside
the drive, this can corrode the electrical
and mechanical components.
!Never immerse the drive in cleaning
fluid or disinfectant.
!Never use an autoclave or an ultra-
sonic bath to clean the drive and the
connecting cable.

45EN
Cheyenne HAWK spirit & HAWK thunder
!Pay attention to compatibility of mate-
rials when selecting cleaning agents
and disinfectants (see the following
chapter “7.1 Material compatibilities”).
7.1 Material compatibilities
!Wherever possible, use one of the
following disinfectants
Manufacturer Product Exposure time
Antiseptica Big Spray
'new' 1 to 5mins
Bode
Chemie Bacillol 30s to 1min
Ecolab Incidin
Foam 1 to 2mins
Schülke &
Mayr
Mikrozid
Liquid 1 to 2mins
Based on the following material compat-
ibilities, you can assess which other clean-
ing agents and disinfectants are suitable
!However, check the material compatibility
in an inconspicuous location.
The anodized aluminum components of
the HAWK SPIRIT and HAWK THUNDER are
resistant to:
Weak acids (e.g. acetic acid ≤10%, citric
acid ≤10%)
Aliphatic fluorocarbons (e.g. pentane,
hexane)
Ethanol
Most inorganic salts and their aqueous
solutions (e.g. sodium chloride, calcium
chloride, magnesium sulphate)
The anodized aluminum components of the
HAWK SPIRIT and HAWK THUNDER are not
resistant to:
Strong acids (e.g. hydrochloric acid,
sulphuric acid, nitric acid)
Oxidizing acids (e.g. peracetic acid)
Lyes (e.g. caustic soda, ammonia and all
substances with a pH value >7)
Aromatic/halogenized fluorocarbons
(e.g. phenol, chloroform) as well as
acetone and benzene
7.2 Disinfecting surfaces
Before and after each usage:
!Disinfect all surfaces of the HAWK SPIRIT
or HAWK THUNDER and its accessories
as described in chapter “5.1 Disinfecting
equipment” on page36.