Chicago Electric 35633 User manual

9” ANGLE GRINDER
MODEL 35633
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
For technical questions and replacement parts, please call 1-800-444-3353
Copyright © 1996 by Harbor Freight Tools®. All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
®
Warning: There are certain applications for which this
tool was designed. Harbor Freight Tools strongly rec-
ommends that this tool not be modified and/or used
for any application other than which it was designed.
All accessories must be rated for at least the RPM
speed recommended on the tool’s warning label.
Wheels and other accessories running over rated
speed can fly apart and cause injury.
For safest operation, it is recommended that only these
accessories be used with this product:
Abrasive Cut-Off Discs and Wheels - Flap Wheels - Wire Brushes - Wire Wheel Brushes
Always use an approved and proper guard when using the above mentioned accessories. Each
accessory must have the correct arbor size and must fit properly on the shoulder bushing. Make
sure accessories are tightened down securely.
CAUTION: NEVER INSTALL A CARBIDE TIPPED OR STEEL CIRCULAR SAW BLADE FOR USE ON
THIS ANGLE GRINDER. NEVER INSTALL A WOOD CARVING BLADE, CARVING DISC WITH SAW
CHAIN CUTTERS, OR A CUTTING CARVING DISC ON THIS ANGLE GRINDER.
Revised Cover Page 05/03

4
VOLTAGEWARNING
Beforeconnectingthe tool toapower source (receptacle,outlet,etc) be surethevoltage supplied is
aboutthe same as that specifiedon the nameplate of thetool. If on says 120Vand theother says 110V
thenthere will benocomplications. Never try toplug a 110Vtoolintoa220Voutlet,ortheotherway
around. Theplugandoutlet have completely differentshapes. Thisisbecause a power source witha
voltagegreater than that specifiedon the toolcanresult in aSERIOUS INJURYtothe user -- aswell
as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with
voltage(110V)lessthanthenameplaterating(220V)isharmfultothemotor.
EXTENSIONCORDS
Your tool isdouble insulated andhas a two-prongplug, you mayuse either atwo - orthree - prong
extensioncord. Onlyuserounded jacket extension cordslistedby the Underwriters Laboratories(UL).
Makesurethe cord isratedfor outdoor use ifyouplan on usingthetool outside; if youplanon indoor
use,you may also use aoutdoor ratedcord. Extension cords rated for outdooruse have the letters
“WA”on the cord jacket.
Theextensioncordmusthaveaminimumwiresizedependingontheamperageofthetoolandthe
lengthoftheextensioncord. This size issignifiedbyitsAWG(AmericanWireGauge)rating;the
smallerthegauge,the greater thecable’scapacity. Ifyou areusingtwo or more cords,thetotallength
ofthecombinedcords must be used todeterminetheminimumAWG rating. Eachofthecordsused
mustmeetthisrating.
Your tool asa 14amp rating. For extension cord lengthsup to 75 feet, youmust usea cord with a
AWGrating of atleast14; for longerlengths, theAWGrating must be12. Donot use morethan 175
feetofextensioncord.
Alwaysinspectextension cords foranydamage. If there areanyloose, frayed orexposedwires,
damagedinsulation,ordefectiveconnections,replacethecord.
HarborFreightToolscan supply ULlisted and outdoor rated cordsinmultipleAWGratingsifneeded.
UNPACKING
Makesureyourtoolhas come complete with all accessories. Your package should includethegrinder,
reversiblesidehandle, steel wheelguard,one wrench and areplacement set of carbonbrushes. Ifa
pieceismissingcontactHarborFreightToolsCustomerSatisfactionatthenumberonthecoverofthis
manual.
OPERATIONS
SelectingWheels:
1.Make sure the wheel you select is rated for at least 8000 RPM.
2.Usesiliconcarbidegrindingwheelsforconcreteandstone.
3.Usealuminumoxide wheelsforferrousmetals. REV02/04