Christie Secure II Series Use and care manual

Secure Series II LCD
Panels
Technical Reference
020-001915-01

NOTICES
COPYRIGHT AND TRADEMARKS
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.
GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this document.
Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary depending on conditions
beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of
printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose. Christie
will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material. Canadian
manufacturing facility is ISO 9001 and 14001 certified.
WARRANTY
Products are warranted under Christie’s standard limited warranty, the details of which are available at https://www.christiedigital.com/help-center/warranties/ or by
contacting your Christie dealer or Christie.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your product. Failure to perform maintenance as required, and in accordance
with the maintenance schedule specified by Christie, will void the warranty.
REGULATORY (if applicable)
The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of the
product in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user’s own expense. Changes
or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
CAN ICES-3 (A) / NMB-3 (A)
이 기기는 업무용(A급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다.
ENVIRONMENTAL
The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol means that electrical and
electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according to local
regulations. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to conserve the environment we
live in!

Secure Series II LCD Panels Technical Reference 3
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Serial communications...........................................................................................................7
RS232 communication parameters.......................................................................................7
Setting up the Ethernet ......................................................................................................7
Command and response format ..............................................................................................7
Direct command format (display from the control system)......................................................7
Value adjust format (display from the control system)............................................................8
Status check command format (display from the control system) ............................................8
Status check response format (control system from the display)..............................................8
OK acknowledgement.........................................................................................................8
Error acknowledgement......................................................................................................9
Serial command list...............................................................................................................9
Set Power Control ...............................................................................................................17
Source Change ...................................................................................................................17
Set Picture Mode.................................................................................................................18
Set Backlight On/Off............................................................................................................18
Increase/Decrease Brightness...............................................................................................18
Increase/Decrease Contrast .................................................................................................19
Increase/Decrease Black level ...........................................................................................19
Increase/Decrease Saturation...............................................................................................19
Increase/Decrease Sharpness...............................................................................................20
Set Color temperature .........................................................................................................20
Increase/Decrease Red gain .................................................................................................21
Increase/Decrease green gain ..............................................................................................21
Increase/Decrease blue gain.................................................................................................21
Set HDR10 on/off................................................................................................................22
Run Picture reset ................................................................................................................22
Set sound input ..................................................................................................................22
Increase/Decrease Volume...................................................................................................23
Increase/Decrease Balance ..................................................................................................23
Set Language .....................................................................................................................24
Set OSD Time.....................................................................................................................24

Content
Secure Series II LCD Panels Technical Reference 4
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Set Power Save...................................................................................................................25
Set Interface Select.............................................................................................................25
Set OPS/HDMI4 EDID ..........................................................................................................25
Set Gamma........................................................................................................................26
Set Auto Source Switch........................................................................................................26
Set Low Latency Mode .........................................................................................................27
Run Factory Reset...............................................................................................................27
Set Preset Mode..................................................................................................................27
Set Multi-window Mode........................................................................................................28
Set Input of window1 ..........................................................................................................28
Set Input of window2 ..........................................................................................................29
Set Input of window3 ..........................................................................................................29
Set Input of window4 ..........................................................................................................30
Run Preset Reset.................................................................................................................30
Remote Control Key ............................................................................................................31
Set Sound Mute ..................................................................................................................31
Set Brightness....................................................................................................................33
Set Contrast.......................................................................................................................33
Set Black Level ...................................................................................................................33
Set Saturation ....................................................................................................................34
Set Sharpness ....................................................................................................................34
Set Red Gain ......................................................................................................................34
Set Green Gain ...................................................................................................................35
Set Blue Gain .....................................................................................................................35
Set Volume ........................................................................................................................35
Set Balance........................................................................................................................36
Set Power Off Mode.............................................................................................................36
Set Preset Mode..................................................................................................................36
Get Power Status ................................................................................................................38
Get Input Source ................................................................................................................38
Get Picture Mode.................................................................................................................39
Get Brightness....................................................................................................................39
Get Contrast.......................................................................................................................39
Get Saturation....................................................................................................................40

Content
Secure Series II LCD Panels Technical Reference 5
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Get Sharpness....................................................................................................................40
Get Color Temperature ........................................................................................................40
Get Red Gain......................................................................................................................41
Get Green Gain...................................................................................................................41
Get Blue Gain .....................................................................................................................41
Get HDR10.........................................................................................................................42
Get Audio Input ..................................................................................................................42
Get Volume........................................................................................................................42
Get Balance........................................................................................................................43
Get Language.....................................................................................................................43
Get OSD Turn Off................................................................................................................44
Get Power Save ..................................................................................................................44
Get OPS/HDMI4 EDID..........................................................................................................44
Get Preset Mode .................................................................................................................45
Get Power Off Mode.............................................................................................................45
Get Interface Select ............................................................................................................46
Get Gamma........................................................................................................................46
Get Auto Source Switch .......................................................................................................47
Get Low Latency Mode.........................................................................................................47
Get Multi-window Mode........................................................................................................47
Get window1 Input..............................................................................................................48
Get window2 Input..............................................................................................................48
Get window3 Input..............................................................................................................49
Get window4 Input..............................................................................................................49
Get Sound Mute..................................................................................................................50
Serial communications.........................................................................................................51
Configuring the RS232 port ..................................................................................................51
Configuring the Ethernet port ...............................................................................................51
Examples: Serial commands and responses............................................................................52
Serial command list.............................................................................................................52
Power control..................................................................................................................53
Input Source ......................................................................................................................54
Backlight............................................................................................................................54
Contrast.............................................................................................................................55
Brightness..........................................................................................................................55

Content
Secure Series II LCD Panels Technical Reference 6
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Saturation..........................................................................................................................55
Sharpness..........................................................................................................................56
Backlight On/Off .................................................................................................................56
Color Temperature ..............................................................................................................57
Red Gain............................................................................................................................57
Green Gain.........................................................................................................................57
Blue Gain...........................................................................................................................58
Baudrate Adjustment...........................................................................................................58
Remote Control...................................................................................................................59
Reset All ............................................................................................................................59
Serial Number Read ............................................................................................................59
Model Name Read ...............................................................................................................60
Firmware Version Read........................................................................................................60
Scheme Selection................................................................................................................61

Secure Series II LCD Panels Technical Reference 7
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
In addition to using the display keypad or remote control unit, you can control the display using a serial
(RS232) link or Ethernet connection to send commands and receive responses to those commands.
The display uses a simple text-based control protocol to take requests from control devices and to provide
responses to such devices. This section describes how to send control messages over a serial link between the
display and an automation/control system or a PC running a terminal emulation program.
The RS232 IN port has several communication parameters.
Parameter
Value
Default baud rate
115200
Parity
None
Data bits
8
Stop bits
1
Flow control
None
The panel support 115200, 38400, 19200, 9600 baud rate. To change the baud rate, on the panel go to
Factory menu and change the baud rate.
Learn how to configure the Ethernet port.
1. Connect the control computer to the RJ45 connector on the display panel.
2. If using TCP/IP, UDP socket program, complete the following to configure the Ethernet port on the
system:
a. Set the IP address(check at LAN setting OSD).
b. Set the port number (TCP/IP: 5000, UDP: 5001).
Commands sent from an automation/control system or PC to the display must have the following format.
Format : [HEAD][SET ID][COMMAND][END]
Example (Power on) : K:ALLPON

External control–ASCII protocol
Secure Series II LCD Panels Technical Reference 8
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
• [HEAD] indicates the start of the command data (always K:).
• [SET ID] is the display ID (always ALL).
• [COMMAND] is the command data (3 Bytes).
• [END] indicates the end of the command data (always a period (.)).
Format : [HEAD][SET ID][COMMAND][VALUE][END]
Example (Volume level 50%) : K:ALLVOL050
• [HEAD] indicates the start of the command data (always K:).
• [SET ID] is the display ID (always ALL).
• [COMMAND] is the command data (3 Bytes).
• [VALUE] is the parameter setting for the command (000 to 100).
• [END] indicates the end of the command data (always a period(.)).
Format : [HEAD][SET ID][COMMAND][END]
Example (Volume level) : K:ALLVOL?
• [HEAD] indicates the start of the command data (always K:).
• [SET ID] is the display ID (always ALL).
• [COMMAND] is the command data (3 Bytes).
• [END] indicates the end of the command data (always question mark (?)).
Format : [SET ID][:][COMMAND][=][REPLY]
Example (Volume level 50%) : ALL:VOL=050
• [SET ID] is the display ID (always ALL).
• [:] is always colon (:).
• [COMMAND] is the command data (3 Bytes).
• [=] is always equal sign (=).
• [Reply] is the reply data (3 Bytes).
The Product transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
Format : [ALL][:][Command][=][A]

External control–ASCII protocol
Secure Series II LCD Panels Technical Reference 9
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Example : ALL:PON=A
If an error occurs, it returns NG.
Format : [ALL][:][Command][=][N]
Example : ALL:PON=N
Main item
Control item
Command
Value
Reply
Direct Control
Power Key Off
POF
Direct Control
Power Key On
PON
Direct Control
Source change to DP1
SH0
Direct Control
Source change to DP2
SH1
Direct Control
Source change to HDMI1
SH2
Direct Control
Source change to HDMI2
SH3
Direct Control
Source change to HDMI3
SH4
Direct Control
Source change to HDMI4
SH5
Direct Control
Source change to OPS/HDMI
SH7
Direct Control
Source change to OPS/DP
SH8
Direct Control
Picture Mode Standard
PM0
Direct Control
Picture Mode Dynamic
PM1
Direct Control
Picture Mode User
PM2
Direct Control
Backlight on
BLN
Direct Control
Backlight off
BLF
Direct Control
Brightness 1step Up
BLU
Direct Control
Brightness 1step Down
BLD
Direct Control
Contrast 1step Up
CTU
Direct Control
Contrast 1step Down
CTD
Direct Control
Black Level 1step Up
BRU
Direct Control
Black Level 1step Down
BRD
Direct Control
Color 1step Up
STU
Direct Control
Color 1step Down
STD
Direct Control
Sharpness 1step Up
SPU
Direct Control
Sharpness 1step Down
SPD
Direct Control
Color temperature set to
Studio1
CT0
Direct Control
Color Temperature set to
Studio2
CT1

External control–ASCII protocol
Secure Series II LCD Panels Technical Reference 10
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Main item
Control item
Command
Value
Reply
Direct Control
Color Temperature set to
Warm
CT2
Direct Control
Color temperature set to
Normal
CT3
Direct Control
Color Temperature set to Cool
CT4
Direct Control
Color Temperature set to User
CT5
Direct Control
Red Gain 1step Up
RGU
Direct Control
Red Gain 1step Down
RGD
Direct Control
Green Gain 1step Up
GGU
Direct Control
Green Gain 1step Down
GGD
Direct Control
Blue Gain 1step Up
BGU
Direct Control
Blue Gain 1step Down
BGD
Direct Control
HDR10 Off
HDF
Direct Control
HDR10 On
HDO
Direct Control
Picture Reset
PIR
Direct Control
Sound DP1
AI0
Direct Control
Sound DP2
AI1
Direct Control
Sound HDMI1
AI2
Direct Control
Sound HDMI2
AI3
Direct Control
Sound HDMI3
AI4
Direct Control
Sound HDMI4
AI5
Direct Control
Sound OPS/HDMI
AI7
Direct Control
Sound OPS/DP
AI8
Direct Control
Volume Up
VLU
Direct Control
Volume Down
VLD
Direct Control
Balance 1step Down
BCD
Direct Control
Balance 1step Up
BCU
Direct Control
OSD Language German
LGE
Direct Control
OSD Language English
LES
Direct Control
OSD Language Spanish
LSP
Direct Control
OSD Language French
LFR
Direct Control
OSD Language Italiano
LIT
Direct Control
OSD Language Korean
LKR
Direct Control
OSD Language Russian
LRU
Direct Control
OSD Time Off
OT0
Direct Control
OSD Time 5Sec
OT1
Direct Control
OSD Time 10Sec
OT2
Direct Control
OSD Time 20Sec
OT3
Direct Control
Power Save Off
PSF

External control–ASCII protocol
Secure Series II LCD Panels Technical Reference 11
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Main item
Control item
Command
Value
Reply
Direct Control
Power Save On
PSN
Direct Control
Interface Select Off
UA0
Direct Control
RS-232
UA1
Direct Control
OPS/RS-232
UA2
Direct Control
OPS/HDMI4 EDID - UHD
EDU
Direct Control
OPS/HDMI4 EDID - FHD
EDF
Direct Control
Gamma 2.2
GST
Direct Control
Gamma DICOM
GDC
Direct Control
Auto Souce Switch Off
AIF
Direct Control
Auto Souce Switch On
AIO
Direct Control
Low Latency Mode Off
LLF
Direct Control
Low Latency Mode On
LLO
Direct Control
Factory Reset
FTR
Direct Control
Preset select10
RN0
Direct Control
Preset select1
RN1
Direct Control
Preset select2
RN2
Direct Control
Preset select3
RN3
Direct Control
Preset select4
RN4
Direct Control
Preset select5
RN5
Direct Control
Preset select6
RN6
Direct Control
Preset select7
RN7
Direct Control
Preset select8
RN8
Direct Control
Preset select9
RN9
Direct Control
Multi-Window Mode Single
WM0
Direct Control
Multi-Window Mode Dual1
WM1
Direct Control
Multi-Window Mode Dual2
WM2
Direct Control
Multi-Window Mode Dual3
WM3
Direct Control
Multi-Window Mode Dual4
WM4
Direct Control
Multi-Window Mode Triple1
WM5
Direct Control
Multi-Window Mode Triple2
WM6
Direct Control
Multi-Window Mode Triple3
WM7
Direct Control
Multi-Window Mode Triple4
WM8
Direct Control
Multi-Window Mode Quad
WM9
Direct Control
Window1 Input DP1
W10
Direct Control
Window1 Input DP2
W11
Direct Control
Window1 Input HDMI1
W12
Direct Control
Window1 Input HDMI2
W13
Direct Control
Window1 Input HDMI3
W14

External control–ASCII protocol
Secure Series II LCD Panels Technical Reference 12
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Main item
Control item
Command
Value
Reply
Direct Control
Window1 Input HDMI4
W15
Direct Control
Window1 Input OPS/HDMI
W17
Direct Control
Window1 Input OPS/DP
W18
Direct Control
Window2 Input DP1
W20
Direct Control
Window2 Input DP2
W21
Direct Control
Window2 Input HDMI1
W22
Direct Control
Window2 Input HDMI2
W23
Direct Control
Window2 Input HDMI3
W24
Direct Control
Window2 Input HDMI4
W25
Direct Control
Window2 Input OPS/HDMI
W27
Direct Control
Window2 Input OPS/DP
W28
Direct Control
Window3 Input DP1
W30
Direct Control
Window3 Input DP2
W31
Direct Control
Window3 Input HDMI1
W32
Direct Control
Window3 Input HDMI2
W33
Direct Control
Window3 Input HDMI3
W34
Direct Control
Window3 Input HDMI4
W35
Direct Control
Window3 Input OPS/HDMI
W37
Direct Control
Window3 Input OPS/DP
W38
Direct Control
Window4 Input DP1
W40
Direct Control
Window4 Input DP2
W41
Direct Control
Window4 Input HDMI1
W42
Direct Control
Window4 Input HDMI2
W43
Direct Control
Window4 Input HDMI3
W44
Direct Control
Window4 Input HDMI4
W45
Direct Control
Window4 Input OPS/HDMI
W47
Direct Control
Window4 Input OPS/DP
W48
Direct Control
Preset Reset
PRT
Direct Control
Remote control Source key
RSO
Direct Control
Remote control Up key
RUP
Direct Control
Remote control Down key
RDN
Direct Control
Remote control Right key
RRT
Direct Control
Remote control Left key
RLT
Direct Control
Remote control Select key
REN
Direct Control
Remote control Menu key
RMN
Direct Control
Remote control Info key
RIF
Direct Control
Mute On
MON
Direct Control
Mute Off
MOF

External control–ASCII protocol
Secure Series II LCD Panels Technical Reference 13
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Main item
Control item
Command
Value
Reply
Value Adjust
Brightness setting
BLT
000 to 100
Value Adjust
Contrast setting
CON
000 to 100
Value Adjust
Black Level setting
BRT
000 to 100
Value Adjust
Color setting
SAT
000 to 100
Value Adjust
Sharpness Value setting
SHA
000 to 100
Value Adjust
Red Gain Setting
RGN
000 to 100
Value Adjust
Green Gain Setting
GGN
000 to 100
Value Adjust
Blue Gain Setting
BGN
000 to 100
Value Adjust
Volume
VOL
000 to 100
Value Adjust
Balance
BCT
000 to 100
Value Adjust
Preset mode
PRS
000 to 020
Value Adjust
Power off mode standby
PWM
000 to 002
Value Adjust
Power off mode sleep
PWM
000 to 002
Value Adjust
Power off mode deep sleep
PWM
000 to 002
Status check
Power status
PWR
000=on
001=off(power save)
002=off(RS232,
remote control)
Status check
Selected Window Status
WIN
001=Window1
002=Window2
003=Window3
004=Window4
Status check
Picture Mode
PMT
000=Standard
001=Dynamic
002=User
Status check
Brightness Setting
BLT
000 to 100
Status check
Contrast Value Setting
CON
000 to 100
Status check
Black Level Value Setting
BRT
000 to 100
Status check
Color Setting
SAT
000 to 100
Status check
Sharpness Value Setting
SHA
000 to 100
Status check
Color temperature
CTT
000 = Studio1
001 = Studio2
002 = Warm
003 = Normal
004 = Cool
005 = User
Status check
Red Gain Setting
RGN
000 to 100
Status check
Green Gain Setting
GGN
000 to 100
Status check
Blue Gain Setting
BGN
000 to 100
Status check
HDR10
HDS
000=Off, 001=On
Status check
Audio Input Status
AUT
000 = DP1
001 = DP2

External control–ASCII protocol
Secure Series II LCD Panels Technical Reference 14
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Main item
Control item
Command
Value
Reply
002 = HDMI1
003 = HDMI2
004 = HDMI3
005 = HDMI4
007OPS-HDMI
008OPS-DP
Status check
Volume
VOL
000 to 100
Status check
Balance
BCT
000 to 100
Status check
OSD Language
LAT
000 = English
001 = German
002 = Spanish
003 = French
004 = Italian
005 = Russian
006 = Korean
Status check
OSD Turn Off
OTT
000 = Off
001 = 5 seconds
002 = 10 seconds
003 = 20 seconds
Status check
Power Save
PST
000=Off, 001=On
Status check
Power Off Mode
PWM
000 = Standby
001 = Sleep
002 = Deep Sleep
Status check
Movie Mode Status
MMT
000 = Off
001 = Low
002 = Middle
003 = High
Status check
UART Status
UAT
000 = Off
001 = RS232
002 = OPS RS232
Status check
OPS/HDMI4 EDID Status
EDI
000 = UHD
001 = FHD
Status check
Gamma Status
GMT
000 = Off
001 = On
Status check
Auto Source Switch Status
AIS
000 = Off
001 = On
Status check
Low Latency Mode
LLS
000 = Off
001 = On
Status check
Preset Mode status
PRS
000 = Multi mode off
001 = Preset1
002 = Preset2
003 = Preset3
004 = Preset4
005 = Preset5
006 = Preset6

External control–ASCII protocol
Secure Series II LCD Panels Technical Reference 15
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Main item
Control item
Command
Value
Reply
007 = Preset7
008 = Preset8
009 = Preset9
010 = Preset10
011 = Preset11
012 = Preset12
013 = Preset13
014 = Preset14
015 = Preset15
016 = Preset16
017 = Preset17
018 = Preset18
019 = Preset19
020 = Preset20
Status check
Multi-Window Mode Status
WMT
000 = Single
001 = Dual1
002 = Dual2
003 = Dual3
004 = Dual4
005 = Triple1
006 = Triple2
007 = Triple3
008 = Triple4
009 = Quad
Status check
Window1 Source Status
W1S
000 = DP1
001 = DP2
002 = HDMI1
003 = HDMI2
004 = HDMI3
005 = HDMI4
007 = OPS-HDMI
008 = OPS-DP
Status check
Window2 Source Status
W2S
000 = DP1
001 = DP2
002 = HDMI1
003 = HDMI2
004 = HDMI3
005 = HDMI4
007 = OPS-HDMI
008 = OPS-DP
Status check
Window3 Source Status
W3S
000 = DP1
001 = DP2
002 = HDMI1
003 = HDMI2
004 = HDMI3
005 = HDMI4
007 = OPS-HDMI
008 = OPS-DP

External control–ASCII protocol
Secure Series II LCD Panels Technical Reference 16
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Main item
Control item
Command
Value
Reply
Status check
Window4 Source Status
W4S
000 = DP1
001 = DP2
002 = HDMI1
003 = HDMI2
004 = HDMI3
005 = HDMI4
007 = OPS-HDMI
008 = OPS-DP
Status check
Current source
SRC
000 = DP1
001 = DP2
002 = HDMI1
003 = HDMI2
004 = HDMI3
005 = HDMI4
007 = OPS-HDMI
008 = OPS-DP
Status check
Mute Status
MUT
000 = Off
001 = On

Secure Series II LCD Panels Technical Reference 17
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
The following commands provide direct command control.
Sets the power control.
Command (ASCII)
Description
Values
K:ALLPOF.
Turns off the power.
—
K:ALLPON.
Turns on the power.
—
Set the power contorl to off:
K:ALLPOF.
Result:
ALL:POF=A
Changes the source.
Command (ASCII)
Description
Values
K:ALLSH0.
Sets the source to DP1.
—
K:ALLSH1.
Sets the source to DP2.
K:ALLSH2.
Sets the source to HDMI1.
K:ALLSH3.
Sets the source to HDMI2.
K:ALLSH4.
Sets the source to HDMI3.
K:ALLSH5.
Sets the source to HDMI4.
K:ALLSH7.
Sets the source to OPS HDMI.
K:ALLSH8.
Sets the source to OPS DP.
Set the sourcel to DP1:
K:ALLSH1.
Result:
ALL:SH1=A

Direct command control
Secure Series II LCD Panels Technical Reference 18
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Sets the picture mode.
Command (ASCII)
Description
Values
K:ALLPM0.
Sets the picture mode to standard.
—
K:ALLPM1.
Sets the picture mode to dynamic.
K:ALLPM2.
Sets the picture mode to user.
Set the picture mode to standard:
K:ALLPM0.
Result:
ALL:PM0=A
Enables or disables the backlight.
Command (ASCII)
Description
Values
K:ALLBLN.
Turns on the backlight.
—
K:ALLBLF.
Turns off the backlight.
Enable the backlight:
K:ALLBLN.
Result:
ALL:BLN=A
Increase or decrease the backlight by one step. Set Picture mode to user.
Command (ASCII)
Description
Values
K:ALLBLU.
Increases the brightness by one step.
—
K:ALLBLD.
Decreases the brightness by one step.

Direct command control
Secure Series II LCD Panels Technical Reference 19
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Increase the brightness by one step:
K:ALLBLU.
Result:
ALL:BLU=A
Inceases or decreases the contrast by one step. Set Picture mode to user.
Command (ASCII)
Description
Values
K:ALLCON.
Increases the contrast by one step.
—
K:ALLCON.
Decreases the contrast by one step.
Increase the contrast one step:
K:ALLCON.
Result:
ALL:CON=A
Increases or decreases the black level by one step. Set Picture mode to user.
Command (ASCII)
Description
Values
K:ALLBLU.
Increases the black level by one step.
—
K:ALLBLD.
Decreases the black level by one step.
Increase the black level by one step:
K:ALLBRU.
Result:
ALL:BRU=A
Increases or decreases the saturation by one step. Set Picture mode to user.

Direct command control
Secure Series II LCD Panels Technical Reference 20
020-001915-01 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Command (ASCII)
Description
Values
K:ALLSTU.
Increases the saturation by one step.
—
K:ALLSTD.
Decreases the saturation by one step.
Increase the saturation by one step:
K:ALLSTU.
Result:
ALL:STU=A
Increases or decreases the sharpness by 10 steps. Set Picture mode to user.
Command (ASCII)
Description
Values
K:ALLSPU.
Increases the sharpness by ten steps.
—
K:ALLSPD.
Decreases the sharpness by ten steps.
Increase by sharpness by ten steps:
K:ALLSPU.
Result:
ALL:SPU=A
Set the color temperature.
Command (ASCII)
Description
Values
K:ALLCT0.
Sets the color temperature to studio1.
—
K:ALLCT1.
Sets the color temperature to studio2.
K:ALLCT2.
Sets the color temperature to warm.
K:ALLCT3.
Sets the color temperature to normal .
K:ALLCT4.
Sets the color temperature to cool.
K:ALLCT5.
Sets the color temperature to user.
Set the picture mode to standard: