Christie APS Series User manual

APS Series
LWU650-APS, LWU530-APS
User’s Manual (Detailed)
Operating Guide
020-001523-01

1
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
LCD Projector
LWU650-APS/LWU530-APS
User's Manual (detailed)
Operating Guide
Thank you for purchasing this projector.
►Before using this product, please read all manuals for this
product. Be sure to read Safety Guide rst. After reading them, store them in a
safe place for future reference.
WARNING
NOTE
Various symbols are used in this manual. The meanings of these symbols are
described below.
About this manual
WARNING
CAUTION
This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.
This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect handling.
Please refer to the pages written following this symbol.

NOTICE This entry notices of fear of causing trouble.
• The information in this manual is subject to change without notice.
• The illustrations in this manual are for illustrative purposes. They may differ
slightly from your projector.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.

2
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Contents
Introduction ............... 3
Features ......................3
Checking the contents of package ....3
Part names ....................4
Projector, Control panel, Ports,
Remote control
Setting up ................. 7
Arrangement ...................7
Connecting with your devices
.....10
Connecting to a power supply
.....17
Fastening the cable
.............17
Using the security bar and slot ....18
Remote control ............ 20
Installing the batteries ...........20
About the remote control signal ...21
Changing the frequency of remote
control signal ..................21
Power on/off .............. 22
Turning on the power ...........22
Turning off the power ...........23
Operating ................ 24
Adjusting the volume ............24
Temporarily muting the sound .....24
Selecting an input signal .........25
Selecting an aspect ratio .........25
Limiting OSD display ............26
Adjusting the projector's elevator ....27
Adjusting the zoom and focus .....28
Adjusting the lens shift ..........29
Using the automatic adjustment feature . . 30
Correcting the distortion .........31
Using the magnify feature ........34
Temporarily freezing the screen ...35
Temporarily blanking the screen ...35
PbyP ( Picture by Picture) /
PIP (Picture in Picture) 36
Using the menu function .........40
Indication in OSD,
Containing items of each menu
EASY MENU. . . . . . . . . . . . . . . 43
IMAGE SETTINGS menu ..... 45
SIZE AND POSITION menu ... 49
INPUT menu .............. 52
SETUP menu .............. 57
AUDIO menu .............. 64
MENU PREFERENCES ...... 65

OPTION menu ............. 70
NETWORK menu ........... 85
SECURITY menu ........... 86
Maintenance .............. 93
Cleaning and replacing the air lter . . 93
Inserting or replacing the
internal clock battery . 95
Other care ....................96
Troubleshooting ........... 98
Related messages .............98
Regarding the indicator lamps ...100
Resetting all settings ...........104
Phenomena that may be easy to
be mistaken for machine defects . . 104
Specications ............ 112


3
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Introduction
Introduction
• Keep the original packing materials, for future reshipment. Be sure
to use the original packing materials when moving the projector. Use special
caution for the lens.
NOTE
The projector provides you with the broad use by the following features.
Checking the contents of package
ü This projector has a variety of I/O ports that supposedly cover for any
business scene. The HDMITM and HDBaseTTM ports can support various
image equipment which have digital interface to get clearer pictures on a
screen.
ü This projector can be controlled and monitored via LAN connection.
Furthermore, you can use the designated USB wireless adapter (optional) to
establish wireless LAN connection.
ü The built-in 16W speaker can deliver sufcient sound volume in a large space
like a classroom without external speakers.
ü Has an HDCR and an eClarity features which are original image stabilizer for
a clearer image.
Please see the Contents of package section in the User’s Manual (concise)
which is a book. Your projector should come with the items shown there. Contact
your dealer immediately if any items are missing.
Features
►Keep small parts away from children and pets. Take care
not to put in the mouth. If swallowed, consult a physician immediately for
emergency treatment.
WARNING

4
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Introduction
Part names
Projector
(1) Speaker (24, 64)
(2) Filter cover (93)
The air lter and intake vent are inside.
(3) Elevator feet (x3) (27)
(4) Remote sensor (21)
(5) Lens (96)
(6) Lens cover
(7) Intake vents
(8) Control panel (5)
(9) FOCUS ring (28)
(10) ZOOM ring (28)
(11) AC (AC inlet) (17)
(12) Exhaust vent
(13) Ports (5)
(14) Security bar (18)
(15) Security slot (18)
(16) Spacer (x 2) (27)
(17) Battery cover (95)
►Do not open or remove any portion of the product, unless the
manuals direct it.
►Do not subject the projector to unstable conditions.
►Do not apply a shock or pressure to this product.
►Do not look into the lens and the openings on the projector while the light
source is on, since the projection ray may cause a trouble on your eyes.
►Keep any object away from concentrated projection light beam. Blocking the
beam by something causes high temperature and could result in re or smoke.
WARNING
►Do not touch around the exhaust vents during use or
just after use, since it is too hot.
►Do not attach anything onto the lens except the lens cover of this
projector because it could damage the lens, such as melting the lens.
CAUTION
(continued on next page)
(7)
(6) (8)
(2)
(3)
(1) (12)
(11)
(9)
(7)
(10)
(4)
(5)
(13)
(14)
(15)
(16)
(17)

5
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Introduction
Part names (continued)
Control panel
(1) STANDBY/ON button (22)
(2) INPUT button (25)
(3) MENU button (40)
(4) STATUS DETAIL indicator (100)
(5) POWER/STATUS indicator (100)
Ports(10 ~ 15)
(1) LAN port
(2) WIRELESS port
(3) HDMI 1 port
(4) HDMI 2 port
(5) HDBaseT port
(6) AUDIO IN1 port
(7) AUDIO IN2 port
(8) AUDIO IN3 (R,L) ports
(9) AUDIO OUT port
(10) COMPUTER IN1 port
(11) COMPUTER IN2 / MONITOR OUT port
(12) CONTROL port
(13) VIDEO port
(continued on next page)
(1) (3)
(2) (5)
(4)
(10)
(8)
(3)(2) (4)
(13)
(12)
(11)
(1)
(7)(5)(9) (6)

6
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Part names (continued)
• Any button marked with “*” is not supported on this projector (99).
NOTE
Back of
the remote control
(1) INPUT button (25)
(2) MY BUTTON 1 button (73, 74)
(3) MY BUTTON 2 button (73, 74)
(4) STANDBY/ON button (22)
(5) ASPECT button (25)
(6) PbyP button
(7) AUTO button (30)
(8) FREEZE button (35)
(9) MAGNIFY ON button (34)
(10) FOCUS + button *
(11) ZOOM + button *
(12) VOLUME + button (24)
(13) MAGNIFY OFF
button (34)
(14) FOCUS - button *
(15) ZOOM - button *
(16) VOLUME - button (24)
(17) PAGE UP button
(18) GEOMETRY button (31)
(19) PICTURE button
(20) MUTE button (24)
(21) PAGE DOWN button
(22) INTERACTIVE button *
(23) NETWORK button
(24) BLANK button (35)
(25) ESC button (21)
(26) MENU button (40)
(27) ENTER button (40)
(28) OSD MSG button
(29) RESET button (40)
(30) ▲/▼/◄/►cursor buttons (40)
(31) Battery cover (20)
(3)
(4)
(7)
(8)
(11)
(12)
(15)
(16)
(20)
(19)
(24)
(23)
(26)
(27)
(29)
(31)
ASPECT
BLANK
ESC MENU
RESET
AUTO
PAGE
DOWN
ON
OFF
FREEZE
UP
ENTER
FOCUS
-
+
ZOOM
-
+
INPUT
INTERACTIVE
MYBUTTON
1 2
PbyP
MAGNIFY VOLUME
-
+
GEOMETRY PICTURE MUTE
NETWORK
OSD MSG
(2)
(1)
(6)
(5)
(10)
(9)
(14)
(13)
(17)
(18)
(21)
(22)
(25)
(30)
(28)
Remote control
Introduction

7
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Setting up
Arrangement
Refer to table T-1 in the end of Setup Guide to determine the screen size and
projection distance.
The values shown in the table are calculated for a full size screen.
(continued on next page)
a Screen size (diagonal)
b Projection distance (±10%, from the projector’s end)
c1 , c2 Screen height (±10%)
• The screen position may shift after installation if the projector is
suspended from the ceiling or other location due to the exibility of the plastic
projector body. If readjustment is necessary, consult with your dealer or service
personnel.
NOTE
Setting up
Install the projector according to the
environment and manner the projector will be
used in.
This projector will perform in a free tilt
angle, as shown in the gures below.
For the case of installation in a special
state such as ceiling mount, the specied
mounting accessories and service may be
required. Before installing the projector,
consult your dealer about your installation.
Tilt 360°
Horizontal 360° Vertical 360° (combination of
horizontal and vertical)

8
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Setting up
Arrangement (continued)
WARNING
(continued on next page)
►Install the projector where you can access the power
outlet easily. If an abnormality should occur, unplug the projector urgently.
Otherwise it could cause a re or electric shock.
►Do not subject the projector to unstable conditions. If the projector falls
or topples over, it could result in injury or damage to the projector and the
surrounding things. Using a damaged projector could result in a re and an
electric shock.
• Do not place the projector in unstable places, such as an inclined surface,
places subject to vibration, on top of a wobbly table or cart, or a surface that is
smaller than the projector.
• Do not put the projector on its side, front or rear position.
• Do not attach nor place anything on the projector unless otherwise specied in
the manual.
• Do not use any mounting accessories except the accessories specied by the
manufacturer. Read and keep the manuals of the accessories used.
• For special installation such as ceiling mounting, be sure to consult your dealer
beforehand.
►
Do not install the projector near thermally conductive or ammable
things. Such things when heated by the projector could result in a re and burns.
• Do not place the projector on a metal stand.
►Do not place the projector where any oils, such as cooking or machine
oil, are used. Oil may harm the product, resulting in malfunction, or falling from
the mounted position. Do not use adhesive such as threadlocker, lubricant and
so on.
►Do not place the projector in a place where it may get wet. Getting the
projector wet or inserting liquid into the projector could cause a re and an
electric shock, and damage the projector.
• Do not place the projector near water, such as in a bathroom, kitchen, or
poolside.
• Do not place the projector outdoors or by the window.
• Do not place anything containing liquid near the projector.

9
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Setting up
Arrangement (continued)
►Place the projector in a cool place with sufcient
ventilation. The projector may shutdown automatically or may malfunction if its
internal temperature is too high.
Using a damaged projector could result in a re and an electric shock.
• Do not place the projector in direct sunlight or near hot objects such as heaters.
• Do not place the projector where the air from an air conditioner or similar unit
will blow on it directly.
• Keep a space of 50 cm or more between a side of the projector and other
objects such as walls.
• Do not place the projector on carpet, cushions or bedding.
• Do not stop up, block nor cover the projector's vent holes. Do not place
anything around the projector that could be sucked in or stuck to the projector's
intake vents.
• Do not place the projector at places that are exposed to magnetic elds, doing
so can cause the cooling fans inside the projector to malfunction.
• When you use the projector with the air lter facing towards the ceiling, it is
clogged more frequently. Clean the air lter periodically.
►Avoid placing the projector in smoky, humid or dusty place. Placing the
projector in such places could cause a re, an electric shock and malfunction of
the projector.
• Do not place the projector near humidiers. Especially for an ultrasonic
humidier, chlorine and minerals contained in tap water are atomized and could
be deposited in the projector causing image degradation or other problems.
• Do not place the projector in a smoking area, kitchen, passageway
or by the window.
• Position the projector to prevent light from directly hitting the projector's remote
sensor.
• Positional deviation or distortion of a projected image, or shift of the focus
may occur due to ambient conditions, and so on. They tend to occur until the
operation becomes stable, especially within about 30 minutes after the light
source is turned on. Check and readjust them as necessary.
• Do not place the product in a place where radio interference may be caused.
• Keep heat-sensitive things away from the projector. Otherwise, they may be
damaged by the heat from the projector.
CAUTION
NOTICE
• When the ambient temperature is around 35 to 40°C, the brightness
of light source is reduced automatically.
NOTE

10
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Setting up
Connecting with your devices
Before connecting the projector to a device, consult the manual of the device to
conrm that the device is suitable for connecting with this projector and prepare
the required accessories, such as a cable in accord with the signal of the device.
Consult your dealer when the required accessory did not come with the product or
the accessory is damaged.
After making sure that the projector and the devices are turned off, perform
the connection, according to the following instructions. Refer to the gures in
subsequent pages.
Before connecting the projector to a network system, be sure to read Network
Guide too.
►Use only the appropriate accessories. Otherwise it could
cause a re or damage the projector and devices.
• Use only the accessories specied or recommended by the projector’s
manufacturer. It may be regulated under some standard.
• Neither disassemble nor modify the projector and the accessories.
• Do not use the damaged accessory. Be careful not to damage the accessories.
Route a cable so that it is neither stepped on nor pinched out.
WARNING
►For a cable with a core at only one end, connect the end
with the core to the projector. That may be required by EMI regulations.
CAUTION
• Plug-and-Play is a system composed of a computer, its operating system
and peripheral equipment (i.e. display devices). This projector is VESA DDC
2B compatible. Plug-and-Play can be used by connecting this projector to a
computer that is VESA DDC (display data channel) compatible.
- Take advantage of this feature by connecting a computer cable to the
COMPUTER IN 1 port (DDC 2B compatible). Plug-and-Play may not work
properly if any other type of connection is attempted.
- Please use the standard drivers in your computer as this projector is a Plug-
and-Play monitor.
• Do not turn on or off the projector while connected to a device in
operation, unless that is directed in the manual of the device. Otherwise it may
cause malfunction in the device or projector.
• The function of some input ports can be selected according to your usage
requirements. Check the reference page indicated beside each port in the
following illustration. (11 ~ 15)
• Be careful not to mistakenly connect a connector to a wrong port. Otherwise it
may cause malfunction in the device or projector.
- When connecting a connector to a port, make sure that the shape of the
connector ts the port.
- Tighten the screws to connect a connector equipped with screws to a port.
- Use the cables with straight plugs, not L-shaped ones, as the input ports of
the projector are recessed.
About Plug-and-Play capability
NOTE
(continued on next page)

11
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Setting up
Connecting with your devices (continued)
(continued on next page)
• Before connecting the projector to a computer, consult the computer’s
manual and check the compatibility of the signal level, the synchronization
methods and the display resolution output to the projector.
- Some signal may need an adapter to input this projector.
- Some computers have multiple screen display modes that may include some
signals which are not supported by this projector.
- Although the projector can display signals with a resolution up to
4K(4096x2160), the signal will be converted to the projector’s panel resolution
before being displayed. The best display performance will be achieved if the
resolutions of the input signal and the projector panel are identical.
• If you connect this projector and a notebook computer, you need output the
display to an external monitor, or output simultaneously to the internal display
and an external monitor. Consult the computer's manual for the setting.
• Depending on the input signal, the automatic adjustment function of this
projector may take some time and not function correctly.
- Note that a composite sync signal or sync-on-green signal may confuse the
automatic adjustment function of this projector (30).
- If the automatic adjustment function does not work correctly, you may not see
the dialog to set the display resolution. In such a case, use an external display
device. You may be able to see the dialog and set an appropriate display
resolution.
NOTE
Computer
HDMI
AUDIO
OUT DISPLAY RS-232C

12
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Connecting with your devices (continued)
(continued on next page)
► Before connecting the projector to a network system, be sure
to obtain the consent of the administrator of the network.
►Do not connect the LAN port to any network that might have the excessive
voltage.
►The designated USB wireless adapter that is sold as an option is required to
use the wireless network function of this projector.
►Do not use any extension cable or device when connecting the adapter to
the projector. Before you insert or pull out the USB wireless adapter from the
projector, turn off the power of the projector and pull out the power cord’s plug
from the outlet. Do not touch the USB wireless adapter while the projector is
receiving AC power.
►To connect both the LAN cable and USB device to the projector, use a LAN
cable that is  at on the side where the plug’s wire is visible. Otherwise, both of
them cannot be connected correctly, or the wire may break (malfunction).
CAUTION
Setting up
RS-232CLAN RS-232C
Computer External device
Access
point
USB wireless
adapter
(optional)

13
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
(continued on next page)
Setting up
Connecting with your devices (continued)
VCR/DVD/Blu-ray DiscTM player
COMPONENT
Cb/Pb Y Cr/Pr RL VIDEO
AUDIO
OUT HDMI
• HDBaseTTM is a technology to transmit image, sound, ethernet or serial
control signal via LAN cable.
• Go to the following URL regarding the device of other company that supports
HDBaseTTM and has been conrmed compatible with this projector.
http://www.christiedigital.com
• LAN or HDBaseTTM input port can be selected as ethernet signal input by
switching in the menu.
• Use LAN cables of up to 100m long. (Up to 70m long for 4K signal.)
Exceeding this length, the image and sounds will be deteriorated, and even
experience malfunction on LAN transmission.
• Qualied cable is required for HDBaseTTM connection.
About HDBaseT™connection

14
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Setting up
(continued on next page)
• The HDMITM port of this model is compatible with HDCP (High-
bandwidth Digital Content Protection) and therefore capable of displaying a
video signal from HDCP compatible DVD players or the like.
- The HDMITM port supports the following signals.
Video signal : 480i@60, 480p@60, 576i@50, 576p@50, 720p@50/60,
1080i@50/60, 1080p@50/60, 4k@24/25/30
Audio signal : Format Linear PCM
Sampling frequency 48kHz / 44.1kHz / 32kHz
- This projector can be connected with another equipment that has HDMITM
connector, but with some equipment the projector may not work properly,
something like no video.
- Be sure to use an HDMITM cable that has the HDMITM logo.
- Use a Category 2-certied HDMITM cable to input 1080p@50/60,
4k@24/25/30 signal to the projector.
- When the projector is connected with a device having DVI connector, use a
DVI to HDMITM cable to connect with the HDMITM input.
NOTE
Connecting with your devices (continued)

15
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Setting up
Connecting with your devices (continued)
Monitor
Speakers
(with an amplier)
R
L
RGB IN

16
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Setting up
Use the supplied cable tie to fasten the cables.
It is recommended to fasten the HDMI cables by using the HDMI cable holder and
the Cable tie to prevent them from coming off. Use a Cable tie with the size of 2.0
x 4.0mm or smaller.
►Do not fasten the cables other than HDMI.
►To fasten the cable, use a supplied Cable tie or plastic tie
with the size of 2.0 x 4.0mm or smaller. A metallic tie may cause damage to the
cables and tie holder.
►Do not bind the cables too tightly. The cables or the hole might be damaged.
WARNING
CAUTION
Remove the screw located on the lower side of
HDMI connector and use it to attach the HDMI
cable holder.
With cable tieNo cable tie
screw
HDMI cable holder Cable tie - medium
HDMI
HDMI
Connecting with your devices (continued)
Fastening the cable

17
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
AC
Power
cord
POWER/STATUS
indicator
Connecting to a power supply
1. Put the connector of the power cord into the
AC (AC inlet) of the projector.
2. Firmly plug the power cord’s plug into the outlet.
In a couple of seconds after the power supply
connection, the POWER/STATUS indicator will
light up in steady orange.
►Please use extra caution when connecting the power cord, as
incorrect or faulty connections may result in re and/or electrical shock.
• Do not touch the power cord with a wet hand.
• Only use the power cord that came with the projector. If it is damaged, consult
your dealer to get a new one. Never modify the power cord.
• Only plug the power cord into an outlet whose voltage is matched to the power
cord. The power outlet should be close to the projector and easily accessible.
Unplug the power cord for complete disconnection.
• Do not distribute the power supply to multiple devices. Doing so may overload
the outlet and connectors, loosen the connection, or result in re, electric shock
or other accidents.
• Connect the ground terminal for the AC inlet of this unit to the ground terminal
of the building using an appropriate power cord (bundled).
WARNING
Please remember that when the DIRECT POWER
ON function is activated (71), the connection of the
power supply makes the projector turn on.
When the AUTO POWER ON function is activated and
the projector is receiving an input signal, it is turned on
by connecting to the power supply (71).
►This product is also designed for IT power systems with a phase-to-
phase voltage of 220 to 240 V.
NOTICE
Fastening the cable
Use the supplied cable tie to fasten the cable.
Setting up
Cable tie - large

18
LWU650-APS/LWU530-APS
User's Manual - Operating Guide 020-001523-01 Rev. 1 (11-2018) LIT MAN USRAPS Series
Using the security bar and slot
A commercially available anti-theft chain or
wire can be attached to the security bar on
the projector. Refer to the  gure to choose
an anti-theft chain or wire.
Also, this product has the security slot for
the Kensington lock.
For details, see the manual of the security
tool.
►Do not use the security bar and slot to prevent the projector
from falling down, since it is not designed for it.
WARNING
►Do not place anti-theft chain or wire near the exhaust vents.
It may become too hot.
CAUTION
• The security bar and slot is not comprehensive theft prevention
measures. It is intended to be used as supplemental theft prevention measure.
NOTE
Setting up
Anti-theft chain or wire
Security bar
19mm
12mm
14mm
Security slot