Christie CineLife+ RGB PLF Assembly instructions

Installation and Setup Guide
020-103072-04
CineLife+ RGB PLF
CP4440-RGB, CP4450-RGB

NOTICES
COPYRIGHT AND TRADEMARKS
Copyright © 2021 Christie Digital Systems USA Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.
GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this
document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary
depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on
information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied
warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection
with the performance or use of this material. Manufacturing facilities in Canada and China are ISO 9001 certified.
Warranty
Products are warranted under Christie’s standard limited warranty, the details of which are available at https://www.christiedigital.com/help-center/
warranties/ or by contacting your Christie dealer or Christie.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your product. Failure to perform maintenance as required, and in
accordance with the maintenance schedule specified by Christie, will void the warranty. For preventative maintenance schedules, refer to
www.christiedigital.com.
REGULATORY
The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at the user’s own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment
CAN ICES-3 (A) / NMB-3 (A)
이 기기는 업무용(A급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다.
ENVIRONMENTAL
The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol means that electrical
and electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according
to local regulations. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to conserve the
environment we live in!

Content
Safety precautions.................................................6
General safety precautions............................................. 6
Laser safety precautions...............................................6
AC power precautions.................................................7
Light intensity hazard distance...........................................7
Product labels.....................................................11
General hazards................................................. 11
Mandatory action.................................................12
Electrical labels..................................................12
Additional hazard labels............................................ 12
Introduction..................................................... 14
Product documentation...............................................14
Related documentation.............................................15
Projector components................................................16
Chiller components................................................. 18
List of components..................................................19
Key features......................................................19
Contact your dealer.................................................19
Technical support...................................................20
Installing and setting up............................................21
Site requirements.................................................. 21
Power specifications.................................................22
Preparing the installation site...........................................22
Lifting and positioning the projector.......................................22
Connecting to power................................................ 25
Connecting to an uninterruptible power supply................................ 29
Installing the lens..................................................31
Installing the touch panel............................................. 33
Projector power modes...............................................34
Setting up the chiller unit............................................. 35
Connecting the chiller communication cable................................35
Connecting the chiller power cable......................................37
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 3
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

Connecting the coolant lines..........................................39
Installing the chiller duct............................................41
Filling and starting the chiller.........................................41
Setting the chiller setpoint...........................................43
Maintaining the chiller..............................................44
System operation for CP4440-RGB and CP4450-RGB projectors......................44
Turning the projector on or off.......................................... 44
Logging on to the projector............................................ 45
Turning the light source on or off.........................................45
Activating marriage.................................................45
Completing the installation checklist.......................................45
Video Input panel................................................. 46
HDMI video source..................................................47
HDMI video formats...............................................47
SDI video source...................................................49
SDI video formats................................................49
Integrated Media Block (IMB) video source...................................54
Series 2 IMB video formats.......................................... 54
HDMI video source connection from an IMB................................57
SDI video source connection from an IMB................................. 57
Using channels to set input signal parameters...........................58
Managing the light source...........................................60
Creating a new laser file for CP4440-RGB and CP4450-RGB........................ 60
Modifying an existing laser file.......................................... 62
Copying existing laser settings to a new file..................................62
Deleting a laser file................................................. 63
Adjusting the image............................................... 64
Calibrating the Intelligent Lens System.....................................64
Correcting vignetting................................................ 64
Adjusting tilt and leveling the projector.....................................64
Correcting keystone effect.............................................65
Displaying a test pattern..............................................66
Adjusting the integrator rod and fold mirror..................................66
Adjusting the boresight...............................................69
Adjusting DMD convergence............................................72
Content
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 4
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

Correcting on-screen color.............................................73
Regulatory...................................................... 74
Safety......................................................... 74
Electro-magnetic compatibility.......................................... 74
Emissions..................................................... 74
Immunity..................................................... 74
Environmental.................................................... 75
Content
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 5
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

Safety precautions
Learn about the safety precautions related to the Christie CineLife+ RGB PLF projector. This projector
is intended for use in a cinema environment.
General safety precautions
Read all safety and warning guidelines before installing or operating the projector.
Warning! If not avoided, the following could result in death or serious injury.
• TRIP OR FIRE HAZARD! Position all cables where they cannot contact hot surfaces, be pulled, be
tripped over, or damaged by persons walking on or objects rolling over the cables.
• This product must be installed within a restricted access location not accessible by the general
public.
• Only personnel who are trained on the precautions for the restricted access location can be
granted entry to the area.
• Install the product so users and the audience cannot enter the restricted area at eye level.
• ELECTRICAL and BURN HAZARD! Use caution when accessing internal components.
• High leakage current present when connected to IT power systems.
• FIRE AND SHOCK HAZARD! Use only the attachments, accessories, tools, and replacement parts
specified by Christie.
• FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.
• Lift equipment must be used to position the product.
• Do not install or operate the projector in any position that does not meet the stated product
specifications for alignment and orientation.
Caution! If not avoided, the following could result in minor or moderate injury.
• Only Christie qualified technicians are permitted to open product enclosures.
Laser safety precautions
Read all safety and warning guidelines before operating the projector laser.
Warning! If not avoided, the following could result in death or serious injury.
• Do not operate the cinema projector without all of its covers in place.
• LASER RADIATION HAZARD! This projector has a built-in Class 4 laser module. Never attempt to
disassemble or modify the laser module.
• Do not look directly into the lens when the light source is on. The extremely high brightness can
cause permanent eye damage.
• Possible hazardous optical radiation emitted from this product. (Risk group 3)
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 6
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

AC power precautions
Read all safety and warning guidelines before connecting to AC power.
Warning! If not avoided, the following could result in death or serious injury.
• SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by
Christie.
• FIRE AND SHOCK HAZARD! Do not attempt operation unless the power cord, power socket, and
power plug meet the appropriate local rating standards.
• SHOCK HAZARD! Do not attempt operation if the AC supply is not within the specified voltage
and current, as specified on the license label.
• SHOCK HAZARD! The optional UPS power cord must be inserted into an outlet with grounding.
• SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning,
removing components, or opening any enclosure.
• Install the product near an easily accessible AC receptacle.
Caution! If not avoided, the following could result in minor or moderate injury.
• FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.
• FIRE OR SHOCK HAZARD! Do not overload power outlets and extension cords.
• SHOCK HAZARD! Power supply uses double pole/neutral fusing.
Light intensity hazard distance
This projector has been classified as Risk Group 3 as per the IEC 62471-5:2015 standard due to
possible hazardous optical and thermal radiation being emitted.
Warning! If not avoided, the following could result in serious injury.
• PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be
permitted. Class 1 Laser Product - Risk Group 3 according to IEC 60825-1:2014 and IEC
62471-5:2015.
• PERMANENT/TEMPORARY BLINDNESS HAZARD! Operators must control access to the beam
within the hazard distance or install the product at the height that prevents exposure of
spectators' eyes within the hazard distance. The hazard zone must be no lower than 2.5 meters
(US installations) or 2.0 meters (global installations) above any surface upon which any persons
are permitted to stand and the horizontal clearance to the hazard zone must be a minimum 1.0
meters.
• EXTREME BRIGHTNESS! Do not place reflective objects in the product light path.
The following diagram and table show the zones for ocular and skin hazard distances:
Safety precautions
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 7
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

• A—Hazard zone. The region of space where the projection light from the laser-illuminated
projector is above emission limits for Risk Group 2. The light intensity may cause eye damage
after a momentary or brief exposure (before a person can avert his or her eyes away from the
light source). The light may cause skin burns to occur.
• B—Hazard distance. Operators must control access to the beam within the hazard distance or
install the product preventing potential exposure of the spectators' eyes from being in the
hazard distance.
• C—No access zone. Horizontal clearance of the no access zone must be a minimum of 1.0
meters.
• D—Vertical distance to hazard zone. The hazard zone must be no lower than 2.5 meters (US
installations) or 2.0 meters (global installations) above any surface upon which any persons
are permitted to stand.
• E—Represents the top view of the projector.
• F—Represents the side view of the projector.
The following table lists the hazard distance for the Christie projector lens with the zoom adjusted to
its most hazardous position.
For US and international hazard distances based upon IEC 62471-5:2015, Photobiological safety of
lamps and lamp systems – Part 5: Image projectors.
Projection Lens
(Throw Ratio 4K)
Part Number Hazard Distance (m)
CP4440-RGB and CP4450-
RGB
0.90:1 HB fixed lens 38-809071-XX 1.6
1.13-1.66:1 DLPCine HB zoom lens 108-342100-XX 2.7
1.13-1.72:1 Enhanced DC 4K HB zoom lens 163-141107-XX 2.9
1.35-1.84:1 Enhanced DC 4K HB zoom lens 163-142108-XX 3.1
1.31-1.85:1 DLPCine HB zoom lens 108-335102-XX 3.1
1.45-2.10:1 Enhanced DC 4K HB zoom lens 163-143109-XX 3.5
Safety precautions
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 8
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

Projection Lens
(Throw Ratio 4K)
Part Number Hazard Distance (m)
CP4440-RGB and CP4450-
RGB
1.45-2.17:1 DLPCine HB zoom lens 108-336103-XX 3.6
1.65-2.70:1 Enhanced DC 4K HB zoom lens 163-144100-XX 4.5
1.63-2.71:1 DLPCine HB zoom lens 108-337104-XX 4.5
1.95-3.26:1 DLPCine HB zoom lens 108-338105-XX 5.4
2.71-3.89:1 DLPCine HB zoom lens 108-278101-XX 6.4
1.13-1.66:1 DLPCine UHC zoom lens 163-103105-XX 2.5
1.13-1.72:1 Enhanced DC 4K UHC zoom lens 163-145101-XX 2.6
1.35-1.84:1 Enhanced DC 4K UHC zoom lens 163-146102-XX 2.7
1.31-1.85:1 DLPCine UHC zoom lens 163-104106-XX 2.7
1.45-2.10:1 Enhanced DC 4K UHC zoom lens 163-147103-XX 3.1
1.45-2.17:1 DLPCine UHC zoom lens 163-105107-XX 3.3
1.65-2.70:1 Enhanced DC 4K UHC zoom lens 163-148104-XX 3.8
1.63-2.71:1 DLPCine UHC zoom lens 163-106108-XX 3.8
1.95-3.26:1 DLPCine UHC zoom lens 163-107109-XX 4.7
2.71-3.89:1 DLPCine UHC zoom lens 163-108100-XX 5.6
The graph that follows is for reference only; use the hazard distances in the preceding table.
CP4440-RGB/CP4450-RGB Hazard distance for HB and UHC lenses
Safety precautions
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 9
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

For Installations in the United States
The following must be in place for laser-illuminated projector installations in the United States:
• The projection room shall be clearly identified by the posting of laser warning and restricted
access signs, and by restricting entry through physical means. The projection room sign must
display the warning "No direct exposure to beam shall be permitted".
• The Christie Laser Projection System Installation Checklist must be fully completed after the
installation and sent to [email protected]. A copy can remain on-site. This
checklist can be found as a separate document in the accessory box with the manual.
• Certain US states have additional laser regulatory requirements. Contact
[email protected] for additional regulatory requirements.
Safety precautions
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 10
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

Product labels
Learn about the labels that may be used on the product. Labels on your product may be yellow or
black and white.
General hazards
Hazard warnings also apply to accessories once they are installed in a Christie product that is
connected to power.
Fire and Shock Hazard
To prevent fire or shock hazards, do not expose this product to rain or moisture.
Do not alter the power plug, overload the power outlet, or use it with extension cords.
Do not remove the product enclosure.
Only Christie qualified technicians are authorized to service the product.
Electrical Hazard
Risk of electric shock.
Do not remove the product enclosure.
Only Christie qualified technicians are authorized to service the product.
Warning! If not avoided, the following could result in death or serious injury.
Electric shock hazard. To avoid personal injury, disconnect all power sources before
performing maintenance or service.
Electrocution hazard. To avoid personal injury, always disconnect all power sources
before performing maintenance or service procedures.
Laser hazard. To avoid personal injury, avoid eye or skin exposure to direct or
scattered radiations.
Caution! If not avoided, the following could result in minor or moderate injury.
Hot surface hazard. To avoid personal injury, allow the product to cool for the
recommended cool down time before touching or handling for maintenance or
service.
Moving fan blade. To avoid personal injury, keep hands clear and loose clothing tied
back. Always disconnect all power sources before performing maintenance or service
procedures.
Notice. If not avoided, the following could result in property damage.
Safety precautions
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 11
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

Mandatory action
Consult the service manual.
Disconnect all power sources before performing maintenance or service procedures.
Electrical labels
Indicates the presence of a protective earth ground.
Indicates the presence of an earth ground.
Additional hazard labels
Indicates Class 4 laser radiation when open. Avoid eye
or skin exposure to direct or scattered radiation.
CLASS 1 LASER PRODUCT IEC 60825-1:2014
Wavelengths:
CP4440-RGB: 450nm - 661nm
CP4450-RGB: 450nm - 645nm
FDA laser variance (US projectors only). This product is
in conformity with performance standards for laser
products under 21 CFR 1040, except with respect to
those characteristics authorized by Variance Number
2019-V-3343 effective on August 16, 2019.
Indicates a light hazard. Do not look directly into the
lens. The extreme high brightness can cause permanent
eye damage. Class 1 Laser Product - Risk Group 3
according to IEC 60825-1:2014 and IEC 62471-5:2015.
Safety precautions
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 12
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

Indicates high leakage current. Earth or ground
connection essential before connecting the power
supply.
Indicates a light hazard. Do not look directly into the
lens. The extreme high brightness can cause permanent
eye damage.
Indicates moving parts hazard for the motorized lens
mount. To avoid personal injury, keep hands clear and
clothing tied back.
Safety precautions
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 13
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

Introduction
This manual is intended for professionally trained operators of Christie high-brightness CineLife+ RGB
PLF projection systems.
For complete production documentation and technical support, go to www.christiedigital.com.
Product documentation
For installation, setup, and user information, see the product documentation available on the Christie
Digital Systems USA Inc. website. Read all instructions before using or servicing this product.
CP4440-RGB
To access the documentation from the Christie website:
• Go to http://bit.ly/2NwVsRy or
https://www.christiedigital.com/en-us/cinema/cinema-products/digital-cinema-projectors/
christie-cp4440-rgb
• Scan the QR code using a QR code reader app on a smartphone or tablet.
CP4450-RGB
To access the documentation from the Christie website:
• Go to http://bit.ly/2UYil0V or
https://www.christiedigital.com/en-us/cinema/cinema-products/digital-cinema-projectors/
christie-cp4450-rgb
• Scan the QR code using a QR code reader app on a smartphone or tablet.
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 14
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

Related documentation
Additional information on the projector is available in the following documents.
•CineLife+ RGB PLF User Guide (P/N: 020-103073-XX)
•CineLife+ RGB PLF Product Safety Guide (P/N: 020-103071-XX)
•CineLife+ RGB PLF Service Guide (P/N: 020-103076-XX)
•CineLife+ 1.1.0 Serial Commands Guide (P/N: 020-103075-XX)
Introduction
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 15
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

Projector components
Learn about the components of the projector
.
Introduction
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 16
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

ID Component
A Projector lens
B Service access door
C Communications panel
External devices are connected here.
D Exhaust duct connection
E Touch panel
A touch-sensitive screen used to control the projector.
The touch panel is an optional feature on CP4415 and CP4420 projectors. If there is no
touch panel installed, use the Remote UI feature. See Using the Remote UI.
F AC input circuit breaker A
G AC input circuit breaker B
H UPS input
I AC receptacle B
J AC receptacle A
K Liquid cooling supply line connection
L Liquid cooling return line connection
M Communication connection for the chiller
N Adjustable feet
Turn the adjustable feet to increase or decrease the projector height.
Introduction
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 17
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

Chiller components
Learn about the components of the chiller
, which is used with CP4440-RGB and CP4450-RGB
projectors.
ID Component
A Coolant hose
B Reservoir fill cap
C Coolant inlet port
D Coolant outlet port
E Exhaust vent
F Communication signal terminal
G Power supply terminal
H Chiller coolant filter
I Coolant drain port
Related information
Setting up the chiller unit (on page 35)
Introduction
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 18
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

List of components
Verify that all components were received with the projector.
• Touch panel, touch panel harness, and panel mounting arm
• High security key to open the projector service access door
• Teyu Chiller CW-6200AN (P/N: 163-124108-XX)
• Chiller Setup Kit Plumbing (P/N: 163-149105-XX)
• Chiller Setup Kit Air Ducts (P/N: 163-150107-XX)
• Coolant Propylene Glycol (P/N: 003-006744-XX)
• Optional PLF Cinema Pedestal (P/N: 163-126100-XX)
An optional UPS inlet power cord is also available.
Key features
Understand the important features of the projector.
• Solid-state Christie RealLaser™ RGB laser illumination
• Three-chip 1.38 inch 4K DLP™ light engine
• Christie CineLife+™ electronics platform for ultra-fast processing
• High frame rate playback of 4K at 120 Hz, for premium, large format cinema venues
• Dual, direct-coupled laser modules integrated in the projector chassis
• Ability to work with Mystique software
• 4K 3D playback capability
• LiteLOC™ color lock feature for constant image brightness and color
• Compatible with ultra high contrast (UHC) lens suite
• External chiller unit with exhaust adapter (CP4440-RGB and CP4450-RGB projectors only)
Contact your dealer
Record the information about your installation and keep this information with your records to assist
with any servicing of your product. If you encounter a problem, contact your dealer.
Purchase record
Dealer:
Dealer or Christie Sales/Service contact phone number:
Serial number:
The serial number can be found on the license label located on the display panel.
Purchase date:
Installation date:
Introduction
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 19
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

Technical support
Technical support for Christie Cinema products is available at:
•[email protected]
• [phone]
• Christie Professional Services: [phone] or [email protected]
Introduction
CineLife+ RGB PLF Installation and Setup Guide–CP4440-RGB, CP4450-RGB 20
020-103072-04 Rev. 1 (03-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.