Christie Cinema 4k-rgb cp4315-rgb Assembly instructions

Installation and Setup Guide

020-102710-08

Cinema 4K-RGB

CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-

RGB

NOTICES

All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this

document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary

depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on

information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied

warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection

with the performance or use of this material. Manufacturing facilities in Canada and China are ISO 9001 certified.

Warranty

Products are warranted under Christie’s standard limited warranty, the details of which are available at https://www.christiedigital.com/help-center/

warranties/ or by contacting your Christie dealer or Christie.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your product. Failure to perform maintenance as required, and in

accordance with the maintenance schedule specified by Christie, will void the warranty. For preventative maintenance schedules, refer to

www.christiedigital.com.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at the user’s own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment

CAN ICES-3 (A) / NMB-3 (A)

이 기기는 업무용(A급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다.

ENVIRONMENTAL

The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol means that electrical

and electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according

to local regulations. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to conserve the

environment we live in!

Content

Safety precautions.................................................5

General safety precautions............................................. 5

Laser safety precautions...............................................5

AC power precautions.................................................6

Light intensity hazard distance...........................................6

Product labels.....................................................12

General hazards................................................. 12

Mandatory action.................................................13

Electrical labels..................................................14

Additional hazard labels............................................ 14

Laser labels....................................................14

Introduction..................................................... 16

Product documentation...............................................16

Related documentation.............................................17

Projector components (front)...........................................18

Projector components (rear)............................................19

List of components..................................................19

Key features......................................................20

Contact your dealer.................................................20

Technical support...................................................20

Installing and setting up............................................21

Site requirements.................................................. 21

Preparing the installation site...........................................21

Lifting and positioning the projector.......................................22

Connecting to power................................................ 23

Connecting to an uninterruptible power supply................................ 26

Installing the lens..................................................28

Installing the touch panel............................................. 29

Projector power modes...............................................30

Turning the projector on or off.......................................... 31

Logging on to the projector............................................ 31

Turning the light source on or off.........................................31

Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 3

020-102710-08 Rev. 1 (03-2021)

Activating marriage.................................................32

Completing the installation checklist.......................................32

Connecting devices and establishing communication.....................33

Projector head connections and status LEDs..................................33

Projector LED status indicators........................................34

SM and FIPS LED status indicators......................................35

LED status indicators..............................................35

Connecting the projector to a network..................................... 35

Connecting the devices to the 3D port......................................35

Managing the light source...........................................36

Creating a new laser file..............................................36

Modifying an existing laser file.......................................... 37

Copying existing laser settings to a new file..................................38

Deleting a laser file................................................. 38

Adjusting the image............................................... 39

Calibrating the Intelligent Lens System.....................................39

Correcting vignetting................................................ 39

Adjusting tilt and leveling the projector.....................................39

Correcting keystone effect.............................................40

Displaying a test pattern..............................................41

Adjusting the integrator rod and fold mirror..................................41

Adjusting the boresight...............................................44

Adjusting DMD convergence............................................47

Correcting on-screen color.............................................48

Regulatory...................................................... 49

Safety......................................................... 49

Electro-magnetic compatibility.......................................... 49

Emissions..................................................... 49

Immunity..................................................... 49

Environmental.................................................... 50

Content

Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 4

020-102710-08 Rev. 1 (03-2021)

Safety precautions

Learn about the safety precautions related to the Christie Cinema 4K-RGB projector. This projector is

intended for use in a cinema environment.

General safety precautions

Read all safety and warning guidelines before installing or operating the projector.

Warning! If not avoided, the following could result in death or serious injury.

• TRIP OR FIRE HAZARD! Position all cables where they cannot contact hot surfaces, be pulled, be

tripped over, or damaged by persons walking on or objects rolling over the cables.

• This product must be installed within a restricted access location not accessible by the general

public.

• Only personnel who are trained on the precautions for the restricted access location can be

granted entry to the area.

• Install the product so users and the audience cannot enter the restricted area at eye level.

• ELECTRICAL and BURN HAZARD! Use caution when accessing internal components.

• High leakage current present when connected to IT power systems.

• FIRE AND SHOCK HAZARD! Use only the attachments, accessories, tools, and replacement parts

specified by Christie.

• FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.

• A minimum of four people or appropriately rated lift equipment is required to safely lift, install,

or move the product.

• Do not install or operate the projector in any position that does not meet the stated product

specifications for alignment and orientation.

Caution! If not avoided, the following could result in minor or moderate injury.

• Only Christie qualified technicians are permitted to open product enclosures.

Laser safety precautions

Read all safety and warning guidelines before operating the projector laser.

Warning! If not avoided, the following could result in death or serious injury.

• Do not operate the cinema projector without all of its covers in place.

• LASER RADIATION HAZARD! This projector has a built-in Class 4 laser module. Never attempt to

disassemble or modify the laser module.

• Do not look directly into the lens when the light source is on. The extremely high brightness can

cause permanent eye damage.

• Possible hazardous optical radiation emitted from this product. (Risk group 3)

Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 5

020-102710-08 Rev. 1 (03-2021)

AC power precautions

Read all safety and warning guidelines before connecting to AC power.

Warning! If not avoided, the following could result in death or serious injury.

• SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by

Christie.

• FIRE AND SHOCK HAZARD! Do not attempt operation unless the power cord, power socket, and

power plug meet the appropriate local rating standards.

• SHOCK HAZARD! Do not attempt operation if the AC supply is not within the specified voltage

and current, as specified on the license label.

• SHOCK HAZARD! The optional UPS power cord must be inserted into an outlet with grounding.

• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product

by Christie qualified technicians or electricians before it can be connected to power.

• SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning,

removing components, or opening any enclosure.

• Install the product near an easily accessible AC receptacle.

Caution! If not avoided, the following could result in minor or moderate injury.

• FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.

• FIRE OR SHOCK HAZARD! Do not overload power outlets and extension cords.

• SHOCK HAZARD! Power supply uses double pole/neutral fusing.

Light intensity hazard distance

This projector has been classified as Risk Group 3 as per the IEC 62471-5:2015 standard due to

possible hazardous optical and thermal radiation being emitted.

Warning! If not avoided, the following could result in serious injury.

• PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be

permitted. Class 1 Laser Product - Risk Group 3 according to IEC 60825-1:2014 and IEC

62471-5:2015.

• PERMANENT/TEMPORARY BLINDNESS HAZARD! Operators must control access to the beam

within the hazard distance or install the product at the height that prevents exposure of

spectators' eyes within the hazard distance. The hazard zone must be no lower than 2.5 meters

(US installations) or 2.0 meters (global installations) above any surface upon which any persons

are permitted to stand and the horizontal clearance to the hazard zone must be a minimum 1.0

meters.

• EXTREME BRIGHTNESS! Do not place reflective objects in the product light path.

The following diagram and table show the zones for ocular and skin hazard distances:

Safety precautions

Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 6

020-102710-08 Rev. 1 (03-2021)

• A—Hazard zone. The region of space where the projection light from the laser-illuminated

projector is above emission limits for Risk Group 2. The light intensity may cause eye damage

after a momentary or brief exposure (before a person can avert his or her eyes away from the

light source). The light may cause skin burns to occur.

• B—Hazard distance. Operators must control access to the beam within the hazard distance or

install the product preventing potential exposure of the spectators' eyes from being in the

hazard distance.

• C—No access zone. Horizontal clearance of the no access zone must be a minimum of 1.0

meters.

• D—Vertical distance to hazard zone. The hazard zone must be no lower than 2.5 meters (US

installations) or 2.0 meters (global installations) above any surface upon which any persons

are permitted to stand.

• E—Represents the top view of the projector.

• F—Represents the side view of the projector.

The following table lists the hazard distance for the Christie projector lens with the zoom adjusted to

its most hazardous position.

For US market only, hazard distances based upon FDA guidance document 1400056, Classification and

Requirements for Laser Illuminated Projectors (LIPs), dated February 18, 2015.

CP4315-RGB, CP4320-RGB, CP4330-RGB

Projection Lens

(Throw Ratio 4K)

Part Number Hazard Distance (m)

CP4315-RGB CP4320-RGB CP4330-RGB

0.90:1 HB fixed lens 38-809071-XX 1.0 1.0 1.1

1.13-1.66:1 DLPCine HB

zoom lens

108-342100-XX 1.4 1.7 1.9

1.13-1.72:1 Enhanced

DC 4K HB zoom lens

163-141107-XX 1.5 1.7 2.0

Safety precautions

Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 7

020-102710-08 Rev. 1 (03-2021)

Projection Lens

(Throw Ratio 4K)

Part Number Hazard Distance (m)

CP4315-RGB CP4320-RGB CP4330-RGB

1.35-1.84:1 Enhanced

DC 4K HB zoom lens

163-142108-XX 1.6 1.8 2.2

1.31-1.85:1 DLPCine HB

zoom lens

108-335102-XX 1.6 1.8 2.2

1.45-2.10:1 Enhanced

DC 4K HB zoom lens

163-143109-XX 1.8 2.1 2.5

1.45-2.17:1 DLPCine HB

zoom lens

108-336103-XX 1.9 2.2 2.6

1.65-2.70:1 Enhanced

DC 4K HB zoom lens

163-144100-XX 2.2 2.6 3.2

1.63-2.71:1 DLPCine HB

zoom lens

108-337104-XX 2.2 2.6 3.2

1.95-3.26:1 DLPCine HB

zoom lens

108-338105-XX 2.8 3.2 3.8

2.71-3.89:1 DLPCine HB

zoom lens

108-278101-XX 3.3 3.8 4.5

3.89-5.43:1 DLPCine HB

zoom lens

108-279101-XX 4.6 5.3 6.3

4.98-7.69:1 DLPCine HB

zoom lens

108-280101-XX 6.6 7.8 8.9

1.13-1.66:1 DLPCine

UHC zoom lens

163-103105-XX 1.3 1.5 1.7

1.13-1.72:1 Enhanced

DC 4K UHC zoom lens

163-145101-XX 1.4 1.5 1.8

1.35-1.84:1 Enhanced

DC 4K UHC zoom lens

163-146102-XX 1.5 1.6 1.9

1.31-1.85:1 DLPCine

UHC zoom lens

163-104106-XX 1.5 1.7 1.9

1.45-2.10:1 Enhanced

DC 4K UHC zoom lens

163-147103-XX 1.7 1.8 2.1

1.45-2.17:1 DLPCine

UHC zoom lens

163-105107-XX 1.8 1.9 2.2

1.65-2.70:1 Enhanced

DC 4K UHC zoom lens

163-148104-XX 2.1 2.3 2.7

1.63-2.71:1 DLPCine

UHC zoom lens

163-106108-XX 2.1 2.3 2.7

1.95-3.26:1 DLPCine

UHC zoom lens

163-107109-XX 2.5 2.8 3.3

2.71-3.89:1 DLPCine

UHC zoom lens

163-108100-XX 3.0 3.4 3.8

Safety precautions

Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 8

020-102710-08 Rev. 1 (03-2021)

Projection Lens

(Throw Ratio 4K)

Part Number Hazard Distance (m)

CP4315-RGB CP4320-RGB CP4330-RGB

3.89-5.43:1 DLPCine

UHC zoom lens

163-109101-XX 4.3 4.8 5.3

4.98-7.69:1 DLPCine

UHC zoom lens

163-110103-XX 6.2 6.9 7.7

The graphs that follow are for reference only; use the hazard distances in the preceding table.

CP4315-RGB Hazard distance for HB and UHC lenses

Safety precautions

Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 9

020-102710-08 Rev. 1 (03-2021)

CP4320-RGB Hazard distance for HB and UHC lenses

CP4330-RGB Hazard distance for HB and UHC lenses

CP4325-RGB

For US market only, hazard distances based upon FDA guidance document 1400056, Classification and

Requirements for Laser Illuminated Projectors (LIPs), dated February 18, 2015.

Safety precautions

Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 10

020-102710-08 Rev. 1 (03-2021)

Projection Lens

(Throw Ratio 4K)

Part Number Hazard Distance

(m)

0.90:1 HB fixed lens 38-809071-XX 1.4

1.13-1.66:1 DLPCine HB zoom lens 108-342100-XX 2.3

1.31-1.85:1 DLPCine HB zoom lens 108-335102-XX 2.6

1.45-2.17:1 DLPCine HB zoom lens 108-336103-XX 3.2

1.63-2.71:1 DLPCine HB zoom lens 108-337104-XX 4.0

1.95-3.26:1 DLPCine HB zoom lens 108-338105-XX 4.3

2.71-3.89:1 DLPCine HB zoom lens 108-278101-XX 5.1

3.89-5.43:1 DLPCine HB zoom lens 108-279101-XX 8.3

1.13-1.66:1 DLPCine UHC zoom lens 163-103105-XX 1.8

1.31-1.85:1 DLPCine UHC zoom lens 163-104106-XX 2.5

1.45-2.17:1 DLPCine UHC zoom lens 163-105107-XX 3.0

1.63-2.71:1 DLPCine UHC zoom lens 163-106108 -XX 3.7

1.95-3.26:1 DLPCine UHC zoom lens 163-107109-XX 4.3

2.71-3.89:1 DLPCine UHC zoom lens 163-108100-XX 5.1

For all other markets, hazard distances based upon IEC 62471-5:2015, Photobiological safety of lamps

and lamp systems – Part 5: Image projectors.

Projection Lens

(Throw Ratio 4K)

Part Number Hazard Distance

(m)

0.90:1 HB fixed lens 38-809071-XX 1.0

1.13-1.66:1 DLPCine HB zoom lens 108-342100-XX 1.2

1.31-1.85:1 DLPCine HB zoom lens 108-335102-XX 1.4

1.45-2.17:1 DLPCine HB zoom lens 108-336103-XX 1.9

1.63-2.71:1 DLPCine HB zoom lens 108-337104-XX 2.4

1.95-3.26:1 DLPCine HB zoom lens 108-338105-XX 2.9

2.71-3.89:1 DLPCine HB zoom lens 108-278101-XX 3.4

3.89-5.43:1 DLPCine HB zoom lens 108-279101-XX 4.0

1.13-1.66:1 DLPCine UHC zoom lens 163-103105-XX 1.0

1.31-1.85:1 DLPCine UHC zoom lens 163-104106-XX 1.1

1.45-2.17:1 DLPCine UHC zoom lens 163-105107-XX 1.4

1.63-2.71:1 DLPCine UHC zoom lens 163-106108-XX 2.0

1.95-3.26:1 DLPCine UHC zoom lens 163-107109-XX 2.5

2.71-3.89:1 DLPCine UHC zoom lens 163-108100-XX 3.1

Safety precautions

Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 11

020-102710-08 Rev. 1 (03-2021)

For Installations in the United States

The following must be in place for laser-illuminated projector installations in the United States:

• The projection room shall be clearly identified by the posting of laser warning and restricted

access signs, and by restricting entry through physical means. The projection room sign must

display the warning "No direct exposure to beam shall be permitted".

• The Christie Laser Projection System Installation Checklist must be fully completed after the

installation and sent to [email protected]. A copy can remain on-site. This

checklist can be found as a separate document in the accessory box with the manual.

• Certain US states have additional laser regulatory requirements. Contact

[email protected] for additional regulatory requirements.

Product labels

Learn about the labels that may be used on the product. Labels on your product may be yellow or

black and white.

General hazards

Hazard warnings also apply to accessories once they are installed in a Christie product that is

connected to power.

Fire and Shock Hazard

To prevent fire or shock hazards, do not expose this product to rain or moisture.

Do not alter the power plug, overload the power outlet, or use it with extension cords.

Do not remove the product enclosure.

Only Christie qualified technicians are authorized to service the product.

Electrical Hazard

Risk of electric shock.

Do not remove the product enclosure.

Only Christie qualified technicians are authorized to service the product.

Safety precautions

Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 12

020-102710-08 Rev. 1 (03-2021)

Warning! If not avoided, the following could result in death or serious injury.

Electric shock hazard. To avoid personal injury, disconnect all power sources before

performing maintenance or service.

Electrocution hazard. To avoid personal injury, always disconnect all power sources

before performing maintenance or service procedures.

Optical radiation hazard. To avoid personal injury, never look directly at the light

source.

Voltage hazard. To avoid personal injury, always disconnect all power sources before

performing maintenance or service procedures.

Caution! If not avoided, the following could result in minor or moderate injury.

Hot surface hazard. To avoid personal injury, allow the product to cool for the

recommended cool down time before touching or handling for maintenance or

service.

Burn hazard. To avoid personal injury, allow the product to cool for the recommended

cool down time before handling for maintenance or service.

Moving parts hazard. To avoid personal injury, keep hands clear and loose clothing

tied back.

Moving fan blade. To avoid personal injury, keep hands clear and loose clothing tied

back. Always disconnect all power sources before performing maintenance or service

procedures.

Notice. If not avoided, the following could result in property damage.

General hazard.

Not for household use.

Mandatory action

Consult the service manual.

Safety precautions

Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 13

020-102710-08 Rev. 1 (03-2021)

Disconnect all power sources before performing maintenance or service procedures.

Electrical labels

Indicates the presence of a protective earth ground.

Indicates the presence of an earth ground.

Additional hazard labels

Indicates high leakage current. Earth or ground

connection essential before connecting the power

supply.

Indicates a light hazard. Do not look directly into the

lens. The extreme high brightness can cause permanent

eye damage.

Laser labels

CP4315-RGB FDA laser variance (US projectors only)

CP4320-RGB FDA laser variance (US projectors only)

CP4325-RGB FDA laser variance (US projectors only)

CP4330-RGB FDA laser variance (US projectors only)

CLASS 1 LASER PRODUCT IEC 60825-1:2014

CP4315-RGB wavelengths: 450 nm - 661 nm

CP4320-RGB wavelengths: 450 nm - 661 nm

CP4325-RGB wavelengths: 450 nm - 645 nm

CP4330-RGB wavelengths: 450 nm - 661 nm

Safety precautions

Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 14

020-102710-08 Rev. 1 (03-2021)

Indicates a light hazard. Do not look directly into the

lens. The extreme high brightness can cause permanent

eye damage.

Class 1 Laser Product - Risk Group 3 according to IEC

60825-1:2014 and IEC 62471-5:2015

Indicates Class 4 laser radiation when open. Avoid eye

or skin exposure to direct or scattered radiation.

Safety precautions

Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 15

020-102710-08 Rev. 1 (03-2021)

Introduction

This manual is intended for professionally trained operators of Christie high-brightness Cinema 4K-

RGB projection systems.

Only trained Christie qualified technicians who are knowledgeable about the hazards associated with

high-voltage, laser safety, and the high temperatures generated by the projector are authorized to

assemble and install the projector. Only Christie qualified technicians are authorized to service the

projector.

For complete production documentation and technical support, go to www.christiedigital.com.

Product documentation

For installation, setup, and user information, see the product documentation available on the Christie

website. Read all instructions before using or servicing this product.

1. Access the documentation from the Christie website:

CP4315-RGB

• Go to https://bit.ly/2JIHhtJ or https://www.christiedigital.com/en-us/cinema/cinema-

products/digital-cinema-projectors/christie-cp4315-rgb

• Scan the QR code using a QR code reader app on a smartphone or tablet.

CP4320-RGB

•Go to https://bit.ly/3n5y11r or https://www.christiedigital.com/en-us/cinema/cinema-

products/digital-cinema-projectors/christie-cp4320-rgb

• Scan the QR code using a QR code reader app on a smartphone or tablet.

CP4325-RGB

•Go to http://bit.ly/2BjQLBq or https://www.christiedigital.com/en-us/cinema/cinema-

products/digital-cinema-projectors/christie-cp4325-rgb

• Scan the QR code using a QR code reader app on a smartphone or tablet.

Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 16

020-102710-08 Rev. 1 (03-2021)

CP4330-RGB

•Go to https://bit.ly/36PfbWj or https://www.christiedigital.com/en-us/cinema/cinema-

products/digital-cinema-projectors/christie-cp4330-rgb

• Scan the QR code using a QR code reader app on a smartphone or tablet.

2. Switch to the Downloads tab.

Popular Projector manuals by other brands

InFocus

InFocus LASER PROJECTOR LP 540 Brochure & specs

InFocus

InFocus IN3114 quick start guide

Sanyo

Sanyo PLC-220P instruction manual

BenQ

BenQ PE8700 - DLP Projector - HD user manual

Panasonic

Panasonic PTD5500U - DLP PROJECTOR Brochure & specs

Epson

Epson PowerLite 420 user guide

Hitachi

Hitachi Innovate CP-RX94 Specifications

Epson

Epson G5150 - Wireless Lan Module 802.11A/B/G Declaration of conformity

JVC

JVC D-ILA DLA-RS45 Firmware upgrade guide

Epson

Epson PowerLite 1750 Installation handbook

Sony

Sony VPL-SX536 Service parts

Epson

Epson 410W - PowerLite WXGA LCD Projector Quick setup

Cube

Cube RIF 6 product manual

InFocus

InFocus SP5000 Software guide

Sony

Sony S Series manual

Epson

Epson V11H604320 installation guide

Sanus

Sanus FPA203 instruction manual

Digital Projection

Digital Projection HIGHlite Cine 260 HB user manual

Christie Cinema 4K-RGB CP4315-RGB Assembly instructions

Popular Projector manuals by other brands