Christie CP2306-RGBe User manual

CP2306-RGBe, CP2308-RGBe, CP2310-RGBe
User Manual
020-001835-02

NOTICES
COPYRIGHT AND TRADEMARKS
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.
GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this document.
Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary depending on conditions
beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of
printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose. Christie
will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material. Canadian
manufacturing facility is ISO 9001 and 14001 certified.
WARRANTY
Products are warranted under Christie’s standard limited warranty, the details of which are available at https://www.christiedigital.com/help-center/warranties/ or by
contacting your Christie dealer or Christie.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your product. Failure to perform maintenance as required, and in accordance
with the maintenance schedule specified by Christie, will void the warranty.
REGULATORY (if applicable)
The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of the
product in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user’s own expense. Changes
or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
CAN ICES-3 (A) / NMB-3 (A)
이 기기는 업무용(A급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다.
ENVIRONMENTAL
The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol means that electrical and
electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according to local
regulations. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to conserve the environment we
live in!

CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 3
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Disclaimer statement.................................................................Error! Bookmark not defined.
General precautions ............................................................................................................11
AC/power precautions..........................................................................................................11
Laser safety precautions ......................................................................................................12
Light intensity hazard distance..............................................................................................12
Product labels.....................................................................................................................13
General hazards ..............................................................................................................13
Mandatory action.............................................................................................................15
Electrical labels................................................................................................................15
Additional hazard labels....................................................................................................15
Product documentation........................................................................................................17
Related documentation.....................................................................................................17
Projector overview ..............................................................................................................17
Contact your dealer.............................................................................................................18
Key features.......................................................................................................................18
Understanding the Christie touch panel interface.....................................................................18
Technical support................................................................................................................19
Turning the projector on or off..............................................................................................20
Logging on to the projector...............................................................................................20
Logging out of the projector..............................................................................................20
Turning the touch panel on or off ..........................................................................................20
Calibrating the touch panel display.....................................................................................20
Turning the light source on or off ..........................................................................................21
Opening or closing the douser...............................................................................................21
Selecting a channel .............................................................................................................21
Adding a network time protocol server...................................................................................21
Deleting a network time protocol server.................................................................................22
Changing the time zone .......................................................................................................22
Changing the time format ....................................................................................................22

Content
CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 4
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Automatically adjusting the time for daylight saving time.........................................................23
Manually adjusting the time offset.........................................................................................23
Activating marriage.............................................................................................................23
Change the orientation of the projected image........................................................................23
Change the projector host name ...........................................................................................24
Change the temperature display ...........................................................................................24
Modifying an existing light source Power/LiteLOC™ file ............................................................25
Deleting a light source Power/LiteLOC™ file............................................................................25
Configuring notifications for lamp alarms ...............................................................................25
Advanced laser power adjustment.........................................................................................25
Adjusting the laser power using JM laser touch panel...............................................................26
Default user access permissions............................................................................................27
Adding a user account .........................................................................................................27
Changing user account permissions.......................................................................................27
Changing a user account password........................................................................................28
Deleting a user account .......................................................................................................28
Connecting the projector to the theater network .....................................................................29
Connecting the projector to network attached storage .............................................................29
Connecting the projector to a media or content network ..........................................................30
Activating SNMP..................................................................................................................30
Downloading MIB information...............................................................................................30
Selecting IMB preferences....................................................................................................32
Activating IMB marriage.......................................................................................................32
Content manager icons........................................................................................................33
Ingesting content and keys ..................................................................................................33
Canceling an ingest .............................................................................................................34
Viewing remaining NAS storage capacity................................................................................34
Filtering content by type ......................................................................................................34
Viewing available keys.........................................................................................................34
Filtering the key list.............................................................................................................34

Content
CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 5
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Deleting local content ..........................................................................................................35
Deleting keys......................................................................................................................35
Collapsing or expanding columns ..........................................................................................35
Viewing content details........................................................................................................35
Loading and playing content.................................................................................................35
Unloading content...............................................................................................................36
Creating a new playlist ........................................................................................................37
Reordering playlist content...................................................................................................37
Adding a time offset to a macro ............................................................................................37
Replacing playlist content.....................................................................................................38
Removing playlist content ....................................................................................................38
Copying a playlist................................................................................................................38
Opening an intermission playlist............................................................................................39
Viewing details about playlist content ....................................................................................39
Importing a playlist .............................................................................................................39
Exporting a playlist..............................................................................................................39
Deleting a playlist ...............................................................................................................40
Adding a channel for HDMI input...........................................................................................41
Adding a channel for IMB input .............................................................................................42
Editing an existing channel...................................................................................................43
Copying existing channel settings to a new channel.................................................................43
Changing the active channel .................................................................................................43
Viewing the channel list .......................................................................................................43
Moving a channel up or down the channel list.........................................................................44
Deleting a channel ..............................................................................................................44
Creating a MCGD file ...........................................................................................................45
Editing an existing MCGD file................................................................................................45
Copying existing MCGD file settings to a new file.....................................................................45
Deleting a MCGD file............................................................................................................46
Creating a TCGD file............................................................................................................46
Editing an existing TCGD file.................................................................................................46
Copying existing TCGD file settings to a new file .....................................................................47
Deleting a TCGD file ............................................................................................................47

Content
CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 6
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Activating the Intelligent Lens System ...................................................................................48
Creating a new ILS file.........................................................................................................48
Calibrating the ILS automatically...........................................................................................48
Editing ILS file settings ........................................................................................................49
Copying existing ILS file settings...........................................................................................49
Deleting an ILS file..............................................................................................................49
Resetting the lens ...............................................................................................................49
Creating a source file...........................................................................................................49
Editing source file settings....................................................................................................50
Copying existing source file settings to a new source file..........................................................50
Deleting a source file...........................................................................................................50
Creating a screen file...........................................................................................................51
Editing screen file settings....................................................................................................51
Copying existing screen file settings to a new screen...............................................................51
Deleting a screen file...........................................................................................................51
Performing digital convergence.............................................................................................52
Resetting digital convergence to the default settings ...............................................................52
Correcting keystone effect....................................................................................................53
Correcting dual projector horizontal keystone .........................................................................53
Correcting dual projector vertical keystone.............................................................................54
Correcting vignetting...........................................................................................................55
Adjusting vertical boresight ..................................................................................................55
Adjusting horizontal boresight ..............................................................................................56
Adjusting digital micromirror device convergence....................................................................57
Adjusting the fold mirror......................................................................................................58
Calibrating the color ............................................................................................................58
Masking the screen edges ....................................................................................................59
Displaying a test pattern......................................................................................................60
Turning off a test pattern.....................................................................................................60
Importing a test pattern.......................................................................................................60
Deleting a test pattern.........................................................................................................60
Scheduling a playlist, content, or automation .........................................................................61

Content
CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 7
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Editing a scheduled event.....................................................................................................61
Copying and pasting an existing scheduled event....................................................................62
Copying and pasting scheduled events for an entire day ..........................................................62
Cutting and pasting a scheduled event...................................................................................62
Deleting a scheduled event...................................................................................................62
Deleting scheduled events for an entire day ...........................................................................63
Changing the day of the week the scheduler starts..................................................................63
Turning the scheduler off .....................................................................................................63
Adding a new storage device ................................................................................................64
Editing storage device settings..............................................................................................64
Setting a storage device as a primary drive............................................................................64
Deleting a storage device .....................................................................................................65
Adding a remote ingest source..............................................................................................65
Editing remote ingest source settings ....................................................................................65
Deleting a remote ingest source............................................................................................65
Creating a 3D file................................................................................................................67
Editing an existing 3D file.....................................................................................................67
Copying a 3D file.................................................................................................................68
Deleting a 3D file ................................................................................................................68
Setting the global audio delay...............................................................................................69
Setting the audio output rate................................................................................................69
Mapping channels ...............................................................................................................69
Enabling Dolby Atmos..........................................................................................................70
Editing Dolby Atmos settings ................................................................................................70
Disabling Dolby Atmos.........................................................................................................70
Enabling multiple projectors .................................................................................................71
Adding a slave projector.......................................................................................................71
Enabling content synchronization ..........................................................................................71
Disabling multiple projectors ................................................................................................72
Disabling a slave projector ...................................................................................................72
Deleting a slave projector ....................................................................................................72

Content
CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 8
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Available macro actions .......................................................................................................73
Christie ACT actions ............................................................................................................74
JNIOR actions.....................................................................................................................74
Dolby Cinema processor actions............................................................................................75
SKA-3D actions...................................................................................................................75
Creating a macro ................................................................................................................76
Running a macro.................................................................................................................76
Adding an action item to an existing macro ............................................................................76
Adding a macro to an existing macro.....................................................................................77
Deleting a macro.................................................................................................................77
Adding an automation device to your auditorium.....................................................................77
Modifying automation device settings ....................................................................................78
Removing an automation device from your auditorium.............................................................78
Creating a new playlist trigger ..............................................................................................78
Editing existing playlist trigger settings..................................................................................79
Deleting a playlist trigger.....................................................................................................79
Creating a new global trigger................................................................................................79
Editing existing global trigger settings ...................................................................................79
Deleting a global trigger.......................................................................................................80
Importing a device library ....................................................................................................80
Viewing a device library .......................................................................................................80
Deleting a device library ......................................................................................................80
Importing a product enhancement.........................................................................................81
Enabling an enhancement ....................................................................................................81
Creating a new backup file ...................................................................................................82
Exporting a backup file ........................................................................................................82
Importing a backup file........................................................................................................82
Sorting backup files by name and date created.......................................................................83
Deleting a backup file ..........................................................................................................83
Adding an upgrade package .................................................................................................83
Viewing a list of available upgrade files ..................................................................................83
Installing an upgrade package ..............................................................................................83
Comparing upgrade packages...............................................................................................84

Content
CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 9
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Deleting an upgrade package................................................................................................84
Restoring settings from a backup file.....................................................................................84
Restoring factory default settings..........................................................................................84
Retrieving and downloading system logs................................................................................85
Running the projector interrogator ........................................................................................85
Downloading a certificate.....................................................................................................85
Inspecting ventilation ..........................................................................................................87
Inspecting and cleaning optics ..............................................................................................87
Recommended service kit.....................................................................................................88
Cleaning the lens ................................................................................................................88
Inspecting the card cage filter...............................................................................................88
Inspecting the light engine compartment filter........................................................................89
Cleaning a washable filter ....................................................................................................90
Replacing the lens...............................................................................................................91
Projector functionality..........................................................................................................92
Projector does not turn on ................................................................................................92
Cannot establish communication with projector ...................................................................92
Display issues.....................................................................................................................92
Flicker, shadows, or dimness.............................................................................................93
Blank screen with no display of cinema image .....................................................................93
Severe motion artifacts ....................................................................................................93
Image is vertically stretched or squeezed ...........................................................................93
Inaccurate display colors ..................................................................................................93
Accessing laser system diagnostics........................................................................................94
Assembling the touch panel..................................................................................................94
Safety................................................................................................................................95
Electro-magnetic compatibility..............................................................................................95
Emissions .......................................................................................................................95
Immunity .......................................................................................................................95
Environmental ....................................................................................................................96
International packaging recycling mark requirements...........................................................96

Content
CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 10
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.

CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 11
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Observe these important safety rules to avoid personal injury or damage to the projector.
This projector must be operated in an environment that meets the operating range, as listed in the projector
specifications (on page 32).
Warning! If not avoided, the following could result in death or serious injury.
• TRIP OR FIRE HAZARD! Position all cables where they cannot contact hot surfaces, be pulled,be
tripped over, or damaged by persons walking on or objects rolling over the cables.
• This product must be installed within a restricted access location not accessible by thegeneral
public.
• Only personnel who are trained on the precautions for the restricted access location canbe
granted entry to the area.
• ELECTRICAL and BURN HAZARD! Use caution when accessing internal components.
• High leakage current present when connected to IT power systems.
• Possible hazardous optical radiation emitted from this product. (Risk group 3 under IEC 62471-5)
• For protection from ultraviolet radiation, keep all product housings intact during operation.
• UV EXPOSURE! Protective UV safety glasses with side shields and Christie approvedprotective
safety clothing must be worn when performing optical adjustments or servicing the product.
• FIRE AND SHOCK HAZARD! Use only the attachments, accessories, tools, and replacement parts
specified by Christie.
• A minimum of four people or appropriately rated lift equipment is required to safely lift, install, or
move the product.
Caution! If not avoided, the following could result in minor or moderate injury.
• Only Christie qualified technicians are permitted to open product enclosures.
Warning! If not avoided, the following could result in death or serious injury.
• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product by
Christie qualified technicians or electricians before it can be connected to power.
• SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by
Christie.
• FIRE AND SHOCK HAZARD! Do not attempt operation unless the power cord, power socket, and
power plug meet the appropriate local rating standards.
• SHOCK HAZARD! The AC power cord must be inserted into an outlet with grounding.
• SHOCK HAZARD! Do not attempt operation if the AC supply is not within the specified voltage and
current, as specified on the license label.
• SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning,
removing components, or opening any enclosure.
• The appliance coupler and main power supply plug must be easily accessible for disconnecting the
product from the power source.

Safety precautions
CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 12
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Caution! If not avoided, the following could result in minor or moderate injury.
• Only Christie qualified technicians are permitted to open product enclosures.
• Install the product near an easily accessible AC receptacle.
• For products containing surge suppressors, you must adhere to the installation and power
requirements.
Read all safety and warning guidelines before operating the projector laser.
Warning! If not avoided, the following could result in death or serious injury.
• Do not operate the cinema projector without all of its covers in place.
• LASER RADIATION HAZARD! This projector has a built-in Class 4 laser module. Never attempt to
disassemble or modify the laser module.
• Do not look directly into the lens when the light source is on. The extremely high brightness can
cause permanent eye damage.
• Possible hazardous optical radiation emitted from this product. (Risk group 3)
This projector has been classified as Risk Group 3 as per the IEC62471 standard due to possible hazardous
optical and thermal radiation being emitted.
Warning! If not avoided, the following could result in death or serious injury.
• PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be
permitted.
• PERMANENT/TEMPORARY BLINDNESS HAZARD! Operators must control access to the beam within
the hazard distance or install the product at the height that prevents exposure of spectators' eyes
within the hazard distance. The hazard zone must be no lower than 2.5 meters (US installations)
or 2.0 meters (global installations) above any surface upon which any persons are permitted to
stand and the horizontal clearance to the hazard zone must be a minimum 1.0 meters.
• EXTREME BRIGHTNESS! Do not place reflective objects in the product light path.
The following diagram and table show the zones for ocular and skin hazard distances:

Safety precautions
CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 13
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
• A—Hazard zone. The region of space where the projection light from the projector is above emission
limits for Risk Group 2. The light intensity may cause eye damage after a momentary or brief
exposure (before a person can avert his or her eyes away from the light source). The light may cause
skin burns to occur.
• B—Hazard distance. Operators must control access to the beam within the hazard distance or install
the product preventing potential exposure of the spectators' eyes from being in the hazard distance.
• C—No access zone. Horizontal clearance of the no access zone must be a minimum of 1.0 meters.
• D—Vertical distance to hazard zone. The hazard zone must be no lower than 2.5 meters (US
installations) or 2.0 meters (global installations) above any surface upon which any persons are
permitted to stand.
• E—Represents the top view of the projector.
• F—Represents the side view of the projector.
Lens
Part number
Hazard distance (m)
1.2-1.72:1, 0.69" DLPCine zoom
108-494108-XX
1.51
1.33-2.1:1, 0.69" DLPCine zoom
108-495109-XX
1.51
1.62-2.7:1, 0.69" DLPCine zoom
108-496100-XX
1.51
2.09-3.9:1, 0.69" DLPCine zoom
108-497101-XX
1.51
For Installations in the United States
The following must be in place for laser-illuminated projector installations in the United States:
• The projection room shall be clearly identified by the posting of laser warning and restricted access
signs, and by restricting entry through physical means. The projection room sign must display the
warning "No direct exposure to beam shall be permitted".
• The Christie Laser Projection System Installation Checklist must be fully completed after the
installation and sent to [email protected]. A copy can remain on-site. This checklist
can be found as a separate document in the accessory box with the manual.
• Certain US states have additional laser regulatory requirements. Go to www.christiedigital.com for
additional regulatory requirements.
Learn about the labels that may be used on the product. Labels on your product may be yellow or black and
white.
Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to
power.
Fire and Shock Hazard

Safety precautions
CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 14
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
To prevent fire or shock hazards, do not expose this product to rain or moisture.
Do not alter the power plug, overload the power outlet, or use it with extension cords.
Do not remove the product enclosure.
Only Christie qualified technicians are authorized to service the product.
Electrical Hazard
Risk of electric shock.
Do not remove the product enclosure.
Only Christie qualified technicians are authorized to service the product.
General hazard.
Electrocution hazard. To avoid personal injury, always disconnect all power sources before performing
maintenance or service procedures.
Hot surface hazard. To avoid personal injury, allow the product to cool for the recommended cool down
time before performing maintenance or service.
Burn hazard. To avoid personal injury, allow the product to cool for the recommended cool down time
before performing maintenance or service.
Optical radiation hazard. To avoid personal injury, never look directly at the light source.
Moving parts hazard. To avoid personal injury, keep hands clear and loose clothing tied back.
Fan hazard. To avoid personal injury, keep hands clear and loose clothing tied back. Always disconnect all
power sources before performing maintenance or service procedures.
Voltage hazard. To avoid personal injury, always disconnect all power sources before performing
maintenance or service procedures.
Not for household use.

Safety precautions
CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 15
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Disconnect all power sources before performing maintenance or service procedures.
Consult the service manual.
Disconnect all power sources before performing maintenance or service procedures.
Indicates the presence of a protective earth ground.
Indicates the presence of an earth ground.
Indicates Class 4 laser radiation when open. Avoid eye or skin exposure to
direct or scattered radiation.
CLASS 1 LASER PRODUCT IEC 60825-1:2014
Wavelengths: 450 nm - 661 nm
FDA laser variance (US projectors only)
This product is in conformity with performance standards for laser products
under 21 CFR 1040, except with respect to those characteristics authorized by
Variance Number 2021-V-0348 effective on April 18, 2021.

Safety precautions
CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 16
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Indicates a light hazard. Do not look directly into the lens. The extreme high
brightness can cause permanent eye damage. Class 1 Laser Product - Risk
Group 3 according to IEC 60825-1:2014 and IEC 62471-5:2015
Indicates high leakage current. Earth connection essential before connecting
the power supply.
Indicates a light hazard. Do not look directly into the lens. The extreme high
brightness can cause permanent eye damage.

CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 17
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
This manual is intended for operators of Christie CP2306-RGBe, CP2308-RGBe, CP2310-RGBe projection
systems.
For complete production documentation and technical support, go to www.christiedigital.com.
For installation, setup, and user information, see the product documentation available on the Christie Digital
Systems USA Inc. website. Read all instructions before using or servicing this product.
1. Access the documentation from the Christie website:
Go to https://bit.ly/3lkZ48l or
https://www.christiedigital.com/products/cinema/projection/
Scan the QR code using a QR code reader app on a smartphone or tablet.
2. On the product page, select the model and switch to the Downloads tab.
Additional information on this product is available in the following documents.
• CP2306-RGBe, CP2308-RGBe, CP2310-RGBe Product Safety Guide (P/N: 020-103453-XX)
• CP2306-RGBe, CP2308-RGBe, CP2310-RGBe Installation and Setup Guide (P/N: 020-103451-XX)
• CP2306-RGBe, CP2308-RGBe, CP2310-RGBe Service Guide (P/N: 020-103454-XX)
• CineLife Serial Commands Guide (P/N: 020-102774-XX)
• CP2306-RGBe, CP2308-RGBe, CP2310-RGBe Specifications Guide (P/N: 020-103452-XX)
The Christie CP2306-RGBe, CP2308-RGBe, CP2310-RGBe is a compact 3DLP cinema projector suited for
theaters with screens up to 10.5 meters (35 feet).
The CP2306-RGBe, CP2308-RGBe, CP2310-RGBe provides an improved user interface and enhanced
functionality, supporting future higher speed video interfaces. The projector supports all external 3D systems
and can be stacked for dual-projection, 3D presentations.

Introduction
CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 18
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
Record the information about your installation and keep this information with your records to assist with any
servicing of your product. If you encounter a problem, contact your dealer.
Purchase record
Dealer:
Dealer or Christie Sales/Service contact phone number:
Serial number:
The serial number can be found on the license label located on the display panel.
Purchase date:
Installation date:
Understand the important features of the projector.
• Playback of cinema video, audio, and timed text
• Touch panel with 1280 X 800 resolution
• 3D ready
• DCI compliant
• Third-party IMB support
• Motorized lens mount
• High Frame Rate capable
• Standard support for High-bandwidth Digital Content Protection (HDCP)
• Content intake through USB 2.0, USB 3.0, or eSATA ports
• HDMI 1.4
• Support for multi-projector playback
• Simple Network Management Protocol (SNMP) support for remote status monitoring
Use the touch panel to control the projector and perform functions such as turning the light on or off, selecting
channels, and viewing status information.

Introduction
CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 19
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
A Left navigation menu—Access permissions
determine the available options. G Turns the light on or off.
B Current access permissions. H Opens and closes the douser.
C Projector name and IP address. I Turns test patterns on or off.
D Current date and time. J Displays channels.
E System status—To display all alarms, tap the
colored icon. K Displays macros.
F Turns the projector on or off. L Playback controls—See Loading and playing content (on
page32).
Technical support for Cinema products is available at:
•[email protected]
•[phone]
•Professional Services: [phone] or [email protected]

CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual 20
020-001835-02 Rev. 1 (05-2021)
Copyright © 2021 Christie Digital Systems USA, Inc. All rights reserved.
This section describes how to operate the projector and adjust projector settings. Only the skilled
professionals are permitted to operate the projector to ensure safe operation of the device.
Turn the projector on to display content or turn the projector off to conserve energy.
1. In the right toolbar, tap and hold Power.
Log on to the projector to access projector menus.
1. Tap Login.
2. In the User list, select a username.
3. Enter your password.
4. Tap Login.
Log out of the projector to restrict access to projector menus or to change access permissions.
1. Tap Logout.
Turn the touch panel on to view projector menus or turn the touch panel off to conserve energy.
1. To turn the touch panel on or off, on the top of the touch panel, press the Power button (A).
Calibrate the touch panel to improve its appearance and responsiveness to touch commands.
2. Log on to the projector.