Christie Inspire Series Assembly instructions

Inspire Series WUXGA
Installation and Setup Guide
020-001933-01

NOTICES
COPYRIGHT AND TRADEMARKS
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.
GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this
document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary
depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on
information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties
of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the
performance or use of this material. Canadian manufacturing facility is ISO 9001 and 14001 certified.
For the most current technical documentation and office contact information, visit www.christiedigital.com.
WARRANTY
Products are warranted under Christie’s standard limited warranty, the details of which are available at https://www.christiedigital.com/help-center/warranties/
or by contacting your Christie dealer or Christie.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your product. Failure to perform maintenance as required, and in
accordance with the maintenance schedule specified by Christie, will void the warranty.
REGULATORY
The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at the user's own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
CAN ICES-3 (A) / NMB-3 (A)
이기기는 업무용 (A 급)으로 전자파적합등록을 한기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며 , 가정 외의 지역에서 사용하는 것을 목적으로 합니다 .
ENVIRONMENTAL
The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol means that
electrical and electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and
according to local regulations. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to
conserve the environment we live in!

Inspire Series Installation and Setup Guide 3
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
Content
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Safety and warning guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
AC/power precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Installation safety and warning guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Laser safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Light intensity hazard distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Product labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Projector overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Contact your dealer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Key features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
How the projector works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
List of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Product documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Related documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Installation and setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Site requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Physical operating environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Projector components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Left view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Right view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Built-in keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Input/Output (I/O) panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
IR remote keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Positioning the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Installing the ceiling mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Adjusting the Projected Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Adjusting the Projector’s Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Stacking Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Cleaning or installing the filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Content
Inspire Series Installation and Setup Guide 4
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
Connecting to AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Turning on the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Turning off the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
LED status indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Shutter LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Setting up the projector lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Adjusting the zoom and focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Adjusting lens position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Resetting the lens to home position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Calculating the lens offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Connecting to devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Connecting to a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Connecting to video equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Configuring communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Setting network environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Adjusting LAN setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Adjusting WLAN setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Adjusting network setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Setting serial port baud rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Enabling serial port echo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Logging on to the web user interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Using the web interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Using the RS-232C interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Re-connecting the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Signal connectivity specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
VGA video formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
HDMI video formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
HDBaseT video formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Picture-in-picture/picture-by-picture (PIP/PBP) compatibility . . . . . . . . . . . . . . . . . . . . . . .49
Regulatory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Laser safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Electro-magnetic compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Inspire Series Installation Installation and Setup Guide 5
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
Introduction
This manual is intended for Christie qualified installers and trained operators of Inspire Series
projection systems.
For complete Inspire Series product documentation and technical support, go to
www.christiedigital.com.
This projector is intended for use in a non-cinema environment.
Safety and warning guidelines
Read all safety and warning guidelines before installing or operating the projector. This projector
must be operated in an environment that meets the operating range specification. Use only the
attachments and/or accessories recommended by Christie. Use of others may result in the risk of
fire, shock, or personal injury.
Warning! If not avoided, the following could result in death or serious injury.
• Do notoperate the product without all of its covers in place.
•FIRE HAZARD! Keep hands,clothes, and all combustible material away from the concentrated
light beam of the projector.
•TRIP OR FIRE HAZARD! Position all cables where they cannot contact hot surfaces, be pulled, be
tripped over, or damaged by persons walking on or objects rolling over the cables.
•SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning,
removing components, or opening any enclosure.
•OPTICAL RADIATION HAZARD! Disconnect the power plug from the AC outlet if the product is not
being used for an extended period of time.
•Do not allow anything to rest on the power cord.
•Do not use under the following conditions:
- In extremely hot, cold or humid environments.
(i) Ensure that the ambient room temperatureiswithin 5°C to 40°C (storage -10°C to 60°C)
(ii) Relative humidity is 10% to 85% RH(storage 5% to 90%RH).
-In areas susceptible to excessive dust and dirt.
-Near any appliance generating a strong magnetic field.
-In direct sunlight.

Introduction
Inspire Series Installation Installation and Setup Guide 6
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
AC/power precautions
Read all AC/power precautions before installing or operating the projector.
Installation safety and warning guidelines
Read all installation safety and warning guidelines before installing the projector.
Laser safety precautions
This product is classified as Class 1 Laser Product-Risk Group 2 according to IEC 60825-1:2014
complies with FDA regulations 21 CFR 1040.10 and 1040.11 as a Risk Group 2, LIP (Laser
Illuminated Projector) as defined in IEC 62471:2006 except for deviations pursuant to Laser Notice
No. 50, dated June 24, 2007.
Caution! If not avoided, the following could result in minor or moderate injury.
• Always provide proper ventilation for the product to prevent overheating.
• Only Christie qualified technicians are permitted to open product enclosures.
• All procedures must be performed by Christie qualified technicians.
Notice. If not avoided, the following may result in equipment or property damage.
• Do not expose the product to moisture.
• Always use a lens plug when installing or moving the product. This prevents contaminants from
entering the product.
• Only use cleaning solutions recommended by Christie. All other cleaning solutions may cause
product damage and will void the warranty.
Warning! If not avoided, the following could result in death or serious injury.
• FIRE HAZARD! Do not use a power cord, harness, or cable that appears damaged.
• FIRE OR SHOCK HAZARD! Do not overload power outlets and extension cords.
•SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by
Christie.
• FIRE AND SHOCK HAZARD! Do not attempt operation unless the power cord, power socket, and
power plug meet the appropriate local rating standards.
•SHOCK HAZARD! Do not attempt operation if the AC supply is not within the specified voltage
and current, as specified on the license label.
• SHOCK HAZARD! The AC power cord must be inserted into an outlet with grounding.
• SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning,
removing components, or opening any enclosure.
• Install the product near an easily accessible AC receptacle.
Warning! If not avoided, the following could result in death or serious injury.
• High leakage current present when connected to IT power systems.
Caution! If not avoided, the following could result in minor or moderate injury.
• ELECTRICAL and BURN HAZARD! Use caution when accessing internal components.
• Only Christie qualified technicians are authorized to use the tools provided in the toolbox.

Introduction
Inspire Series Installation Installation and Setup Guide 7
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
Warning! If not avoided, the following could result in death or serious injury.
• This projector has a built-in Class 4 laser module. Never attempt to disassemble or modify the
projector.
• Any operation or adjustment not specifically instructed in the User manual creates the risk of
hazardous laser radiation exposure.
• Do not open or disassemble the projector as this may cause damage or exposure to laser
radiation.
•Do not stare into beam when the projector is on. The bright light may result in permanent eye
damage.
• When turning on the projector, make sure no one within projection range is looking into the lens.
• Follow all installation, operation, adjustment, and maintenance procedures to avoid possible
exposure to hazardous laser radiation.

Introduction
Inspire Series Installation Installation and Setup Guide 8
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
Product labels
Learn about the labels that may be used on the product. Labels on your product may be yellow or
black and white.
General hazards
Hazard warnings also apply to accessories once they are installed in a Christie product that is
connected to power.
Electrical labels
Fire and Shock Hazard
To prevent fire or shock hazards, do not expose this product to rain or moisture.
Do not alter the power plug, overload the power outlet, or use it with extension cords.
Do not remove the product enclosure.
Only Christie qualified technicians are authorized to service the product.
Electrical Hazard
Risk of electric shock.
Do not remove the product enclosure.
Only Christie qualified technicians are authorized to service the product.
Notice! If not avoided, the following could result in property damage.
General hazard.
Indicates the presence of an earth ground.

Introduction
Inspire Series Installation Installation and Setup Guide 9
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
Laser labels
Do not look directly into the lens. The extremely high brightness can
cause permanent eye damage.
This projector has been classified as Class 1 Laser Product-Risk Group
2 according to the IEC 60825-1:2014 and IEC 62471- 5:2015
standard.
Indicates a light hazard. Do not look directly into the lens. The extreme
high brightness can cause permanent eye damage.
Class 1 Laser Product-Risk Group 2 according to Class 1 IEC 60825-
1:2014 and IEC 62471-5:2015.
Mount above the heads of children.
Christie recommends using a ceiling mount to place the product above
eye-level for children.
Make sure to adjust the feet of the top projector before stacking to
avoid damage to the lower projector.

Introduction
Inspire Series Installation Installation and Setup Guide 10
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
Projector overview
The Inspire Series is a high brightness, professional projector system designed with laser phosphor
technology and Digital Light Processing (DLP™) technology from Texas Instruments. With its
superior image quality and high brightness level, the product can be used for various large venue
application ranging from fixed installation, rental stage and LBE (Location Based Entertainment),
but not intended to use for domestic purpose.
Contact your dealer
Record the information about your projector and keep this information with your records to assist
with the servicing of your projector. If you encounter a problem with your Christie projector, contact
your dealer.
Key features
Understand the important features of the projector.
• WUXGA 1920 × 1200 resolution
• High picture quality with superb brightness performance
• Powered lens adjustment with lens memory function
• Projection lens compatibility:
DWU760-iS/DWU860-iS/DWU960-iS/DWU960ST-iS:
• Horizontal offset ranges with half image size: +/-110%
• Vertical offset ranges with half image size: +/-50%
Measurements comply with industry standards where offset is calculated as a ratio of the
number of pixels shifted up or down to half image size.
Purchase record
Dealer:
Dealer or Christie Sales/Service contact phone number:
Projector serial number:
The serial number can be found on the license label
Purchase date:
Installation date:
Ethernet settings
Default gateway:
Projector IP address:
Subnet mask:

Introduction
Inspire Series Installation Installation and Setup Guide 11
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
• Full HD 3D technology with frame sequential up to 120 Hz
• Christie Twist™ and Mystique™ allow for easy and quick blending and warping.
Support for Mystique™ camera based alignment system (sold separately)
• A wide range of connectivity including HDMI, HDBaseT, and 3D inputs
• Integrated HDBaseT solution supports HD video streaming through RJ45
• SNMP traps and email notifications
• 10-bit image processor electronics with modular design
• All video formats can be resized to full screen either horizontally or vertically while maintaining
aspect ratio.
• The projector can be operated using any of the following:
• The built-in keypad, the infrared (IR) remote keypad, a wired remote keypad, or a PC/
device using serial communications (Ethernet or RS232)
• A web page using Ethernet, or from a PC or device using a wireless USB dongle
How the projector works
The Inspire Series projector accepts a variety of input signals for a wide range of commercial
projection applications.
Designed with red and blue solid-state illumination light sources and phosphor technology, the red,
green and blue color elements are modulated by one Digital Micromirror Device (DMD) panel
responding to incoming data streams of digitized red, green, and blue color information. As these
digital streams flow from the source, light from the responding on pixels of the DMD panel is
reflected, converged, and then projected to the screen through projection lenses, where all pixel
reflections are superimposed in sharp full-color images.
List of components
This projector comes with all the items listed below. Check to make sure your package is complete.
If anything is missing, contact your dealer.
• IR remote keypad
• Product Safety Guide

Introduction
Inspire Series Installation Installation and Setup Guide 12
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
Product documentation
For installation, setup, and user information, see the product documentation available on the
Christie Digital Systems USA Inc. website at www.christiedigital.com. Read all instructions before
using or servicing this product.
1. Access the documentation from the Christie website:
• Go to this URL: https://bit.ly/3fXJcI3 or
https://www.christiedigital.com/products/projectors/all-projectors/inspire-series/
• Scan the QR code using a QR code reader app on a smartphone or tablet.
2. On the product page, select the model and switch to the Downloads tab.
Related documentation
Additional information on the projector is available in the following documents.
• Christie Inspire Series Product Safety guide (P/N: 020-001932-XX)
• Christie Inspire Series User Manual (P/N: 020-001934-XX)
• Christie Inspire Series Service Manual (P/N: 020-001935-XX)
• Inspire Series Serial API Commands Technical Reference (P/N: 020-103542-XX)

Inspire Series Installation and Setup Guide 13
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
Installation and setup
Learn how to install, connect, and optimize the projector display.
Site requirements
To safely install and operate the projector, the installation location must have restricted access for
authorized personnel only and meet these minimum requirements.
Physical operating environment
Provides specifications for the operating environment.
• Ambient temperature (operating): 0°C to 40°C (32°F to 104°F) up to 762 m (2500 feet)
• Humidity (non-condensing): 10% to 85% RH
• Operating altitude: 3048 m (10,000 feet) at 0°C to 30°C (32°F to 86°F) ambient temperature
Power connection
The projector uses an AC power system that allows the projector to operate at full brightness with a
power supply ranging from 100 to 240 VAC, depending on the models and regions. Operating the
device outside of the voltage range may cause unsatisfactory operation or damage to the projector.
Christie recommends a 20 A rated wall breaker for the installation. To ensure safe operation, only
use the AC power cord provided with the product or recommended by Christie. See Connecting to
AC power on page 28 for further information on the power requirements.
Physical specifications
Learn the dimensions and weight of the projector before installation.
• Projection size (L x W x H): 18.8” x 15.9” x 6.1” (480 x 406 x 157 mm)
• Shipping size (L x W x H): 25.5” x 22.4” x 14.9” (650 x 570 x 380 mm)
•Weight:
• DWU760-iS: 12.9 kg (28.4 lbs)
• DWU860-iS, DWU960-iS, and DWU960ST-iS: 13.85 kg (30.5 lbs)

Installation and setup
Inspire Series Installation and Setup Guide 14
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
• Shipping weight:
• DWU760-iS: 16.45 kg (36.2 lbs)
• DWU860-iS, DWU960-iS, and DWU960ST-iS: 17.4 kg (38.3 lbs)
Projector components
Identify the main components of the projector.
Front view
Identify the main components on the front of the projector.
ID Part name Description
1 LED status indicators Displays the status of the projector.
2 Projection lens Allows powered and automatic lens shifting and adjustment: vertical and
horizontal offsets, zoom, and focus.
3 Adjustable feet Raises or lowers the feet to level the projector.
4 Front IR sensor Receives signals from the IR remote keypad. Keep the signal path to the
sensors unobstructed for uninterrupted communication with the projector.
1
2
3
4

Installation and setup
Inspire Series Installation and Setup Guide 15
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
Rear view
Identify the main components on the rear of the projector.
Left view
Identify the main components on the left side of the projector.
ID Part name Description
1 Input/Output (I/O) panel Connects the projector to external devices.
2 Built-in keypad Controls the projector.
3 AC input Connects to the supplied power adapter.
4 Power button Powers the projector on or off.
5 Kensington lock Secures the projector to counter tops, tables, and so on.
ID Part name Description
1Cooling air vents (intake) Provides cooling to the projector. Keep these vents unobstructed to prevent
the projector from overheating.
ZOOM FOCUS
1
5
2
3
4
1

Installation and setup
Inspire Series Installation and Setup Guide 16
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
Right view
Identify the main components on the right side of the projector.
Built-in keypad
The built-in keypad controls the projector.
ID Part name Description
1Cooling air vents
(exhaust) Provides cooling to the projector. Keep these vents unobstructed to prevent the projector from overheating.
ID Button Description
1 Four Directional Select Keys Use to select items or make adjustments to your selection.
2LENS SHIFT Adjusts the lens setting.
3 ENTER Confirms your item selection.
4FOCUS Adjusts the image focus.
5KEYSTONE Adjusts keystone.
6 EXIT Exits the current page and returns to the previous page.
7 MENU Press MENU to launch the on-screen display (OSD) menu. To exit the OSD,
press MENU and EXIT again.
8Power Turns the projector on or off.
9ZOOM Adjusts the image size.
1
ZOOM FOCUS
7
9
81
2
3
5
6
4
S
T
W
X
S
X
T
W

Installation and setup
Inspire Series Installation and Setup Guide 17
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
Input/Output (I/O) panel
Identify the components of the Input/Output (I/O) panel.
ID Connector name ID Connector name
1 12V OUT 8 VGA IN
2 3D SYNC (IN) 9 HDMI OUT
3 3D SYNC (OUT) 10 HDMI1 (v2.0 4K)
4 USB (5V 1.5A) 11 HDMI2
5 AUDIO IN 12 LAN
6AUDIOOUT 13HDBaseT
7 RS232-C 14 REMOTE IN
123456
789101113 1214

Installation and setup
Inspire Series Installation and Setup Guide 18
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
IR remote keypad
The IR remote keypad communicates with the projector by way of wireless communications.
If you choose to use a cable, not supplied, it must be 20 m (65.7 ft) or less. If the length of cable
exceeds 20 m (65.7 ft), the IR remote keypad may not work correctly.
ID Button Description
1 SHUTTER Displays or blanks the video image.
2 ON Turns the projector on.
3 GAMMA Adjusts the mid-range levels.
4 BRIGHT Adjusts the amount of light in the image.
SHUTTER
VGA
HDMI2 DVI-D
BNC
DP
3G-SDI HDBaseT
PRESENT.
CVBS
HDMI1
16
17
18
19
20
21
22
24
25
26
27
28
29
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
23

Installation and setup
Inspire Series Installation and Setup Guide 19
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
5PIP
PBP Turns picture-in-picture/picture-by-picture (PIP/PBP) on or off.
6 SIZE Adjusts the PIP/PBP size.
7 Number Keys Enter a number, such as a channel, value, and so on. The on-screen display
(OSD) indicates if a function is not supported.
8 HELP Displays the instructions for source connection.
9MENU Displaysthemenus.
10 Arrow Keys Adjusts a setting up or down to navigate within a menu.
11 TEST Displays a test pattern.
12 AUTO Automatically optimizes an image.
13 OSD Hides or shows OSD menus.
14 KEYSTONE H Adjusts the horizontal keystone.
15 KEYSTONE V Adjusts the vertical keystone.
16 STANDBY Turns the projector off.
17 CONTR Adjusts the difference between dark and light.
18 HOT
KEY
Selects your preset key quickly.
19 SWAP Swaps the main and PIP/PBP images.
20 LAYOUT Adjusts the PIP/PBP layout.
21 FOCUS Adjusts the focus to improve image clarity as required.
22 ZOOM Adjusts the zoom to achieve a required image size.
23 PROJ Changes the IR remote keypad ID.
• To assign an ID, press PROJ + <1to 9>.
• To return to the universal IR remote ID, press PROJ + 0.
24 EXIT Returns to the previous level or exits menus if at the top level.
25 ENTER Selects a highlighted menu item, or changes or accepts a value.
26 INPUT Selects an input for the main or PIP/PBP image.
27 INFO Displays the projector information.
28 LENS H Adjusts the position of the image horizontally.
29 LENS V Adjusts the position of the image vertically.
ID Button Description

Installation and setup
Inspire Series Installation and Setup Guide 20
020-001933-01 Rev. 1 (10-2021)
Copyright ©2021 Christie Digital Systems USA Inc. All rights reserved.
Positioning the display
When you select a position for the projector, consider the size and shape of your screen, the
location of your power outlets, and the distance between the projector and the rest of your
equipment. Follow these general guidelines:
• Position the projector on a flat surface at a right angle to the screen. The projector (with the
standard lens) must be at least 1.33 m (4.3 ft) from the projection screen.
• Position the projector to the required distance from the screen. The distance from the lens of
the projector to the screen, the zoom setting, and the video format determine the size of the
projected image.
• Determine the lens throw ratio.
For more information detailing the throw ratio for each lens, refer to the Inspire Series Lens
Throw Ratios Technical Reference (P/N: 020-103497-XX).
• 360 degree free orientation operation
When installing the projector in portrait orientation, Christie recommends the built in keypad and
power inputs face upwards. This allows access to the built in keypad and power connections during
operation.