Chrysler PACIFICA 2018 User manual

 QUICK REFERENCE GUIDE
CHRYSLER PACIFICA

Adaptive Cruise Control
(ACC) — If Equipped
If your vehicle is equipped with Adaptive Cruise Con-
trol, the controls operate exactly the same as the
standard cruise control, with one difference. You can
set a specified distance you would like to maintain
between you and the vehicle in front of you.
• If the ACC sensor detects a vehicle ahead, ACC
will apply limited braking or acceleration automati-
cally to maintain a preset following distance while
matching the speed of the vehicle ahead.
NOTE:
Your vehicle will not exceed the cruise speed you have
set.
• If the sensor does not detect a vehicle directly
ahead of you, it functions like a standard cruise
control system, maintaining the speed you set.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Canadian
Residents).
Standard Cruise Control Switches
1 — Push Cancel
2 — Push Set+/Accel
3 — Push Resume
4 — Push On/Off
5 — Push Set-/Decel
Adaptive Cruise Switches
1 — Adaptive Cruise Control (ACC) On/Off
2 — Distance Setting – Decrease
3 — Distance Setting – Increase
SPEED CONTROL

Forward Collision Warning
With Mitigation — If
Equipped
The Forward Collision Warning (FCW) system can
provide the driver with active braking, audible and
visual warnings (within the instrument cluster display)
and may apply a brake jerk to warn the driver when it
detects a potential frontal collision. The warnings and
limited braking are intended to provide the driver with
enough time to react and avoid or mitigate the poten-
tial collision.
The system status can be selected to: “Off”, “Only
Warning”, and “Warning & Braking”. “Warning & Brak-
ing” status with “Medium” sensitivity are the default
settings, but can be changed within the Uconnect
settings under “Safety and Driving Assistance”.
FCW monitors the information from the forward-
looking sensor, as well as the Electronic Brake Control-
ler (EBC) and wheel speed sensors, to calculate the
probability of a collision. When the system determines
that a collision is probable, a warning message (both
audible and visual) will be displayed within the cluster
display along with a brake jerk warning (previously
enabled in the Uconnect Settings). When the system
senses the driver applying the brakes to avoid a prob-
able collision, additional brake force will be provided
to the vehicle. When the system determines a collision
with the vehicle in front of you is no longer probable,
the warning message will be deactivated.
NOTE:
The FCW feature can be customized and turned off
through the Uconnect System touchscreen.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Canadian
Residents).
LaneSense With Lane Keep
Assist — If Equipped
The LaneSense system uses a forward looking camera
to detect lane markings and measure vehicle position
within the lane boundaries. The LaneSense system is
operational at speeds above 37 mph (60 km/h) and
below 112 mph (180 km/h).
Turning LaneSense ON Or OFF
The LaneSense button is located on the switch panel
below the Uconnect display.
The LaneSense system will retain the last system state,
on or off, from the previous ignition cycle.
LaneSense Button
SAFETY FEATURES

LaneSense Warning Message
The LaneSense system will indicate the current lane
drift condition through the instrument cluster display.
The visual warning depicted in the instrument cluster
display will vary depending on the unintentional lane
departure conditions, as described next.
The LaneSense indicator in the instrument cluster
display will be solid green when both lanes are de-
tected and the system is “armed” to provide visual and
torque warnings when the driver unintentionally drifts
out of the lane (no turn signal applied). When the
vehicle approaches a lane marker, the telltale will turn
solid yellow. The yellow telltale will begin flashing
yellow when the vehicle is crossing the lane marker.
The LaneSense system will also provide a haptic warn-
ing in the form of a torque applied to the steering
wheel to prompt the driver to remain within the lane
boundaries. The driver may manually override the
haptic warning by applying torque to the steering
wheel at any time.
When the LaneSense system is on but not armed, the
telltale in the instrument cluster display will be solid
white. This occurs when only the left, right, or neither
lane has been detected. If a single line is detected and
the driver unintentionally drifts across the detected
lane marking (no turn signal applied), the system is
ready to provide only visual warnings to prompt the
driver to remain within the lane. When only a single
lane marking is detected, a haptic (torque) warning
will not be provided and a visual warning will only be
provided for the detected lane.
NOTE:
The LaneSense system can be customized through
the Uconnect System touchscreen. Under “Safety and
Driving Assistance” there are two menu items:
• Warning: Early, Med, Late
• Strength: Low, Med, High
When operating conditions have been met, the
LaneSense system will monitor if the driver’s hands
are on the steering wheel and provide an audible
and visual warning to the driver when the driver’s
hands are not detected on the steering wheel. The
system will cancel if the driver does not return their
hands to the wheel.
For further information, telltale icons, and applicable
warnings and cautions, please refer to the
Owner’s Manual at www.mopar.com/en-us/care/
owners-manual.html (U.S. Residents) or
www.owners.mopar.ca (Canadian Residents).

ParkSense Rear Or
ParkSense Front And Rear
Park Assist — If Equipped
The ParkSense Park Assist system provides visual and
audible indications of the distance between the rear
fascia and a detected obstacle when backing up, e.g.
during a parking maneuver. If equipped with front
sensors, visual and audible indications will also be pro-
vided for obstacles in front of the vehicle (the front
sensors can also give indications when moving in re-
verse). The vehicle brakes may be automatically ap-
plied and released when performing a reverse parking
maneuver if the system detects a possible collision
with an obstacle.
• The four ParkSense sensors, located in the rear
fascia/bumper, monitor the area behind the vehicle
that is within the sensor’s field of view. These sen-
sors can detect obstacles from approximately
12 inches (30 cm) up to 79 inches (200 cm) from
the rear bumper while the vehicle is in REVERSE.
• The six ParkSense sensors (if equipped), located in
the front fascia/bumper, monitor the area in front
of the vehicle that is within the sensors’ field of view.
These sensors can detect obstacles from approxi-
mately 12 inches (30 cm) up to 47 inches (120 cm)
from the front fascia/bumper in the horizontal di-
rection, depending on the location, type, and ori-
entation of the obstacle.
•
When an obstacle is detected, a warning will display
in the instrument cluster and a chime will sound
(when “Sound and Display” is selected from the Cus-
tomer Programmable Features section of the
Uconnect System screen). As the vehicle moves
closer to the object, the chime rate will change from
single 1/2 second tone, to slow, to fast, to continuous.
• If the system detects a potential impact with an
object, the vehicle brakes may be applied.
Enabling And Disabling ParkSense
ParkSense can be enabled and disabled with the
ParkSense switch, located on the switch panel below
the Uconnect display.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Canadian
Residents).
ParkSense Switch
PARKSENSE

Parksense Active Park
Assist System
The ParkSense Active Park Assist system is intended
to assist the driver during parallel and perpendicular
parking maneuvers by identifying a proper parking
space, providing audible/visual instructions, and con-
trolling the steering wheel. The ParkSense Active Park
Assist system is defined as “semi-automatic” since the
driver maintains control of the accelerator, gear selec-
tor and brakes. Depending on the driver's parking
maneuver selection, the ParkSense Active Park Assist
system is capable of maneuvering a vehicle into a
parallel or a perpendicular parking space on either side
(i.e., driver side or passenger side).
NOTE:
• The driver is always responsible for controlling the
vehicle, responsible for any surrounding objects,
and must intervene as required.
• The system is provided to assist the driver and not
to substitute the driver.
• During a semi-automatic maneuver, if the driver
touches the steering wheel after being instructed to
remove their hands from the steering wheel, the
system will cancel, and the driver will be required to
manually complete the parking maneuver.
• The system may not work in all conditions (e.g.
environmental conditions such as heavy rain, snow,
etc., or if searching for a parking space that has
surfaces that will absorb the ultrasonic sensor
waves).
• New vehicles from the dealership must have at least
30 miles (48 km) accumulated before the
ParkSense Active Park Assist system is fully cali-
brated and performs accurately. This is due to the
system’s dynamic vehicle calibration to improve the
performance of the feature. The system will also
continuously perform the dynamic vehicle calibra-
tion to account for differences such as over or
under inflated tires and new tires.
Enabling And Disabling The ParkSense Active Park
Assist System
The ParkSense Active Park Assist system can be en-
abled and disabled with the ParkSense Active Park
Assist switch, located on the switch panel below the
Uconnect display.
ParkSense Active Park Assist Switch Location

To enable the ParkSense Active Park Assist system,
push the ParkSense Active Park Assist switch once
(LED turns on).
To disable the ParkSense Active Park Assist system,
push the ParkSense Active Park Assist switch again
(LED turns off).
When the ParkSense Active Park Assist system is
enabled the “Active ParkSense Searching - Push OK
to Switch to Perpendicular” message will appear in the
instrument cluster display. You may switch to perpen-
dicular parking if you desire. Push the OK button on
the left side steering wheel switch to change your
parking space setting. You may switch back to parallel
parking if you desire.
Refer to your Owner's Manual at www.mopar.com/
en-us/care/owners-manual.html (U.S. Residents) or
www.owners.mopar.ca (Canada Residents) for further
details.
Rear Back-Up Camera —
If Equipped
Your vehicle may be equipped with the ParkView Rear
Back-Up Camera that allows you to see an on-screen
image of the rear surroundings of your vehicle when-
ever the gear selector is put into REVERSE. The
ParkView Rear Back-Up Camera image will be dis-
played on the Uconnect Display, located on the center
stack of the instrument panel. The ParkView Rear
Back-Up Camera is located on the rear of the vehicle
above the rear license plate.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Canadian
Residents).
Surround View Camera
System — If Equipped
Your vehicle may be equipped with the Surround View
Camera System that allows you to see an on-screen
image of the surroundings and top view of your ve-
hicle whenever the gear selector is put into REVERSE
or a different view is selected through the "on screen
soft buttons". The top view of the vehicle will show
which doors are open. The image will be displayed on
the touchscreen display along with a caution note
“Check Entire Surroundings” across the top of the
screen. After five seconds, this note will disappear.
The Surround View Camera System is comprised of
four cameras located in the front grille, rear liftgate
and side mirrors.
NOTE:
The Surround View Camera System has program-
mable settings that may be selected through the
Uconnect System.
PARKVIEW

When the vehicle is shifted out of REVERSE (with
camera delay turned ON), the camera image will con-
tinue to be displayed for up to 10 seconds after shifting
out of REVERSE, unless the vehicle speed exceeds
8 mph (13 km/h) or the vehicle is shifted into PARK or
the ignition is switched to the OFF position.
When the vehicle is shifted out of REVERSE (with
camera delay turned OFF), the surround view camera
mode is exited and the last known screen appears
again. There is a touch screen button (X) to disable
the display of the camera image.
Modes of Operation
Additional camera modes can be selected when the
vehicle is in any gear and the surround view camera
system is activated by pressing the soft key located in
the “Controls” screen or the “Apps” screen in the
Uconnect system.
Deactivation
The system can be deactivated in the following con-
ditions:
• The speed of the vehicle reaches greater than
8 mph (13 km/h).
• The vehicle is out of REVERSE for greater than
10 seconds.
• The vehicle shifted into PARK.
• If the vehicle is in any gear other than REVERSE,
press the “X” button.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Canadian
Residents).
Memory Seats — If Equipped
This feature allows the driver to store up to two differ-
ent memory profiles for easy recall through a memory
switch. Your vehicle is equipped with two key fobs.
One key fob can be linked to memory position 1 and
the other can be linked to memory position 2.
The memory positions can also be programmed to
recall the same positions when the unlock button is
pushed.
Memory Seat Buttons
SEATS

To Create A New Memory Profile
1. Cycle the vehicle’s ignition to the ON/RUN posi-
tion (Do not start the engine).
2. Adjust all memory profile settings to desired pref-
erences (i.e., seat, side mirror, power tilt and tele-
scopic steering column [if equipped], and radio
station presets).
3. Push and release the S (Set) button on the memory
switch.
4. Within five seconds, push and release either of the
memory buttons (1) or (2). The instrument cluster
display will show which memory position has been
set.
NOTE:
Memory profiles can be set without the vehicle in
PARK, but the vehicle must be in PARK to recall a
memory profile.
Linking And Unlinking The Remote Keyless Entry
Key Fob To Memory
Your key fob can be programmed to recall one of two
pre-programmed memory profiles by pushing the un-
lock button on the key fob.
To program your key fob, perform the following:
1. Cycle the vehicle’s ignition to the OFF position.
2. Select a desired memory profile (1 or 2).
3. Once the profile has been recalled, push and re-
lease the set (S) button on the memory switch.
4. Push and release button (1) or (2) accordingly.
“Memory Profile Set” (1 or 2) will display in the
instrument cluster.
5. Push and release the lock button on the key fob
within ten seconds.
NOTE:
Your key fob can be unlinked to your memory settings
by pushing the set (S) button, and then, within ten
seconds, pushing the unlock button on the key fob.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Canadian
Residents).
Stow ‘n Go Seating —
If Equipped
On vehicles equipped with Stow 'n Go seating, the
second and third row seats can be folded into the floor
for convenient storage.
Auto Advance ‘n Return — If Equipped
With the Auto Advance ‘n Return feature, the front
seat will move forward with the push of a button. This
allows the front seat to move to a location that will not
interfere when the second row seat is stowed.
NOTE:
The Auto Advance ‘n Return feature is available to
both the front driver and passenger power seats, if
equipped.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Canadian
Residents).

Power Adjustment (Rear
Seats) — If Equipped
Third Row Power Recline
The power recline feature, located on the trim panel
next to the seat, adjusts the seatback angle forward/
rearward for occupant comfort.
Push and hold the forward or rearward button, the seat
will move in the direction of the button push. Release
the button when the desired position is reached.
Third Row Power Stow ‘n Go Seat
A one-touch power folding seat switch is located in
the right rear trim panel accessible from the cargo area
as part of a switch bank. You can also adjust the 3rd row
recline angle using the switch bank.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Canadian
Residents).
Rear Panel Power Switch Bank
1 — Open To Normal
2 — Stow
3 — Fold Forward/Rearward
4 — Right/Left Seats/Both Seats

Hands-Free Sliding Doors –
If Equipped
To open the Hands-Free Sliding Doors, use a straight
in and out kicking motion under the vehicle in the
general location below the door handle(s). Do not
move your foot sideways or in a sweeping motion or
the sensors may not detect the motion.
When a valid kicking motion is completed, the sliding
door will chime, the hazard lights will flash and the
sliding door will open almost instantaneously. This
assumes all options are enabled in the radio.
NOTE:
• To open the Hands-Free Sliding Doors requires a
valid Passive Entry key fob within 5 ft (1.5 m) of the
door handle. If a valid Passive Entry key fob is not
within 5 ft (1.5 m), the door will not respond to any
kicks.
• The Hands-Free Sliding Door will only operate
when the transmission is in Park.
• The Hands-Free Sliding Doors will reverse while
opening and closing if anything obstructs the door,
provided it meets sufficient resistance.
• If a power sliding door encounters multiple ob-
structions within the same cycle, the system will
automatically stop.
• The Hands-Free Sliding Doors feature may be
turned on or off in Uconnect Settings. The Hands-
Free Sliding Doors feature should be turned off
during Jacking, Tire Changing, and Vehicle
Service.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Canadian
Residents).
Hands-Free Sliding Doors
HANDS-FREE SLIDING
DOORS/LIFTGATE

Hands-Free Liftgate —
If Equipped
To open the Hands-Free Liftgate, use a straight in and
out kicking motion under the vehicle activation zone in
the general location below the liftgate door handle.
Do not move your foot sideways or in a sweeping
motion or the sensors may not detect the motion.
Vehicles Equipped With A Trailer Tow Package
If your vehicle is equipped with the Trailer Tow
Package, the hands-free activation zone(s) for the
Power Liftgate will be located on the left and right
side of the receiver. Use a straight kicking motion
under either activation zone to open the Hands-
Free Liftgate.
When a valid kicking motion is completed, the liftgate
will chime, the hazard lights will flash and the liftgate
will open after approximately 1 second. This assumes
all options are enabled in the radio.
NOTE:
• To open the Hands-Free Liftgate requires a valid
Passive Entry key fob within 5 ft (1.5 m) of the door
handle. If a valid Passive Entry key fob is not within
5 ft (1.5 m), the liftgate will not respond to any kicks.
• The Hands-Free Liftgate feature may be turned on
or off in Uconnect Settings. The Hands-Free Lift-
gate feature should be turned off during Jacking,
Tire Changing, and Vehicle Service.
NOTE:
• The Hands-Free Liftgate will only operate when
the transmission is in Park.
• If anything obstructs the Hands-Free Liftgate while
it is opening, the liftgate will automatically reverse
to the closed position, provided it meets sufficient
resistance.
• There are pinch sensors attached to the side of the
liftgate opening. Light pressure anywhere along
these strips will cause the liftgate to return to the
open position.
• If the power liftgate encounters multiple obstruc-
tions within the same cycle, the system will auto-
matically stop. If this occurs, the liftgate must be
operated manually.
Hands-Free Liftgate Activation Zone Hands-Free Liftgate Trailer Tow
Activation Zones

• The power liftgate will release, but not power open,
in temperatures below −12° F (−24° C). Be sure to
remove any buildup of snow or ice from the liftgate
before opening the liftgate.
• If the liftgate is left open for an extended period of
time, the liftgate may need to be closed manually
to reset power liftgate functionality.
Gas props support the liftgate in the open position.
However, because the gas pressure drops with tem-
perature, it may be necessary to assist the props when
opening the liftgate in cold weather.
NOTE:
Allow the power system to open the liftgate. Manually
pushing or pulling the liftgate may activate the liftgate
obstacle detection feature and stop the power opera-
tion or reverse its direction.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Canadian
Residents).
Stow ‘n Vac Integrated
Vacuum — If Equipped
Your vehicle may be equipped with an integrated
vacuum system. This vacuum is for in-vehicle use only
and should only be used on dry materials and on
in-vehicle surfaces. It is located in the rear trim panel
behind the sliding door on the driver’s side of the
vehicle.
NOTE:
Read all vacuum instructions, located in the lower
access panel, before using. When using your vacuum,
basic precautions should be followed.
Front Storage Compartments
1 — Vacuum Nozzle Storage Location
2 — Attachment Compartment
UTILITY FEATURES

For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Canadian
Residents).
Electric Park Brake (EPB)
Your vehicle is equipped with an Electric Park Brake
(EPB) system that offers simple operation and some
additional features that make the park brake more
convenient and useful.
The park brake switch is located in the integrated
center stack.
To engage the park brake manually, push the Electric
Park Brake Switch.
To disengage the park brake manually, the ignition
switch must be in the ON/RUN position. Press the
brake pedal, then push the park brake switch down
momentarily.
The park brake will disengage automatically when the
ignition is in the ON/RUN position, the transmission is
in DRIVE or REVERSE, the driver’s seat belt is buck-
led, and an attempt is made to drive away by pressing
the accelerator pedal.
The new Auto Park Brake feature can be used to apply
the park brake automatically every time you park the
vehicle. Auto Park Brake can be enabled and disabled
in the Settings menu in Uconnect.
SafeHold is a new feature that will automatically apply
the park brake under certain conditions. The EPB
monitors the status of the driver’s seat belt, driver’s
door, and pedal positions to determine if the driver
may have exited while the vehicle is still capable of
moving and will then automatically apply the park
brake to prevent the vehicle from rolling.
Vacuum System Access Panels
1 — Upper Access Panel
2 — Lower Access Panel
Electric Park Brake Switch
STARTING AND
OPERATING

NOTE:
• You may hear a slight whirring sound from the back
of the vehicle while the park brake engages or
disengages.
• Once the park brake is fully engaged, the BRAKE
warning lamp in the instrument cluster and the LED
indicator on the switch will illuminate. Once the
park brake is fully disengaged, the BRAKE warning
lamp in the instrument cluster and the LED indica-
tor on the switch will extinguish.
• If your foot is on the brake pedal while you are
engaging or disengaging the park brake, you may
notice a small amount of brake pedal movement.
• The park brake can be engaged even when the
ignition switch is OFF; however, it can only be
disengaged when the ignition switch is in the ON/
RUN position.
• The EPB fault lamp will illuminate if the EPB switch
is held for longer than 20 seconds in either the
released or applied position. The light will extin-
guish upon releasing the switch.
• Refer to “Electric Park Brake” in the “Starting And
Operating” section in your Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Cana-
dian Residents) for further details.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Canadian
Residents).
Engine STOP/START
System (ESS) — If Equipped
The STOP/START system was developed to reduce
emissions by stopping the engine automatically dur-
ing a vehicle stop if the conditions are met and the
brake is depressed. The system defaults back ON at
every ignition cycle.
STOP/START Off Switch

Releasing the brake pedal, pressing the accelerator
pedal, or shifting out of DRIVE (D) will start the
engine.
How do I manually turn off/on the engine STOP/
START system?
• Press the STOP/START OFF switch (located on
the instrument panel). The light on the switch will
illuminate when the system is off. The light on the
switch will turn off when system is on.
What are possible reasons the engine does not
autostop?
• The hood is ajar. • The transmission is
not in a forward gear.
• Driver’s door is open. •
Cabin heating or cool-
ing is in process and an
acceptable cabin tem-
perature has not been
achieved.
• Driver’s seat belt is
unbuckled.
• The vehicle has not
reached a speed of
5 mph (8 km/h) after
the previous autostop.
• Many of these reasons are displayed as a STOP/
START message in the instrument cluster display
on the STOP/START screen. The system must be
in the “STOP/ START READY” state to autostop.
To access the STOP/START section of the instru-
ment cluster display, use the display controls. Refer
to the “Starting and Operating” section of your
Owner’s Manual at www.mopar.com/en-us/
care/owners-manual.html (U.S. Residents) or
www.owners.mopar.ca (Canadian Residents) for a
complete list of possible events in which the engine
does not autostop.
How do I know I am in an autostop?
•
The engine will shut down, the ta-
chometer will move to the zero posi-
tion and the STOP/START telltale will
illuminate in the instrument cluster.
How do I start the engine while in an autostop?
• While in a forward gear, the engine will start when
the brake pedal is released or the throttle pedal is
depressed. The transmission will automatically re-
engage upon engine restart.
STOP/START Message

Automatic High Beam —
If Equipped
This system automatically controls the operation of
the headlamp high beams as oncoming vehicles ap-
proach.
• The Automatic High Beam Headlamp Control can
be turned on or off using the Uconnect System.
• Push the turn signal lever away from you.
• With the headlight switch in the “AUTO” position,
the high beams are controlled automatically.
• Pull the turn signal lever toward you to manually
deactivate the system.
• To improve system recognition of crossing traffic,
and to limit use in a residential area, the vehicle
must be moving at a speed greater than 20 mph
(32 km/h) before the Automatic High Beam Mod-
ule (AHBM) begins requesting high beam
activation.
NOTE:
If the windshield or Automatic High Beam Headlamp
Control mirror is replaced, the mirror must be re-
aimed to ensure proper performance. See a local au-
thorized dealer.
Vehicle User Guide
Access your Owner’s Information right through your
Uconnect 4 or 4C NAV touchscreen system — If
Equipped.
To access the Vehicle User Guide on your Uconnect
Touchscreen: Press the Uconnect Apps button, then
press the Vehicle User Guide icon on your touch-
screen. No Uconnect registration is required.
NOTE:
Vehicle User Guide features are not available while the
vehicle is moving. If you try to access while the vehicle
is in motion, the system will display: Feature not avail-
able while the vehicle is in motion.
Pre-Installed Features
tq;rrYour User Guide —
Updated in real-time
Available when and where
you need it
Touchscreen convenience Customizable interface
Maintenance schedules
and information
Multilingual
Comprehensive icon & symbol glossary
Features
SiriusXM Guardian keeps you connected to your ve-
hicle. You have access to safety, remote and security
services.
In-Vehicle Features
SiriusXM Guardian enhances your ownership and
driving experience by connecting your vehicle to an
operable network. When connected to an operable
network, you have access to:
• SOS Call: Connect to a live agent who contact
emergency services and stays on the line with you
until help arrives.
Vehicle User Guide Home Screen
LIGHTS VEHICLE USER GUIDE
— IF EQUIPPED SIRIUSXM GUARDIAN — IF EQUIPPED

• Customer Care Assistance: Speak with a live agent
when you press the ASSIST button on your rear-
view mirror to get Roadside Assistance or support.
Remote Services
SiriusXM Guardian helps you activate features from a
distance. The remote services are:
• Vehicle Finder helps you find where you parked
your car.
• Send & Go allows you to send preset destinations
to your navigation system for easy access on the go.
• Remote Door Lock/Unlock lets you unlock or lock
your doors from any distance.
• Remote Horn & Lights allows you to sounds your
horn and flash your lights to easily find your car.
• Receive monthly Vehicle Health Reports, and
Alerts whenever a problem is detected under the
hood.
Security Services
The Uconnect Mobile App helps you activate fea-
tures from a distance. The remote services are:
• Receive text or email notifications if your vehicle's
security alarm goes off.
• Receive stolen vehicle assistance, using GPS tech-
nology to help authorities locate your vehicle if it is
stolen.
SiriusXM Guardian remote services can be used with
the Uconnect app from virtually anywhere.
For further information on SiriusXM Guardian or the
Uconnect Mobile App, refer to your Uconnect Own-
er’s Manual Supplement.
Activation
To use SiriusXM Guardian emergency, remote and
security services, you must activate your SiriusXM
Guardian account.
1. Press the Apps icon on the bottom of your in-
vehicle touchscreen.
2. Select the “Activate Services” icon from your list of
apps.
3. Select “Customer Care” to speak with a SiriusXM
Guardian Customer Care agent who will activate
services in your vehicle, or select “Enter Email” to
activate on the web.
Once you have activated your services, you’re only a
few steps away from using remote services.
To use SiriusXM Guardian remote services, download
the Uconnect Mobile app:
• Once downloaded, use your Owner Account login
and password to open the app.
• Include similar language: You will use your
SiriusXM Guardian PIN to execute these remote
services.
Mobile App

• Press the “Location” button on the bottom menu
bar of the app to bring up a map to locate your
vehicle or send a location to your Uconnect Navi-
gation, if equipped.
• Press the “Settings” side menu in the upper left
corner of the app to bring up app settings and
access the Assist Call Centers.
For further information:
• U.S. residents visit: siriusxm.com/guardian
• Canadian residents visit: siriusxm.com/guardian/ca
Vehicle Finder And Send &
Go
Two of the most convenient remote features of the
Uconnect Mobile App are Vehicle Finder and Send &
Go.
Vehicle Finder
Vehicle Finder allows you to find the location of your
vehicle when you have lost it. You can also sound the
alarm and flash the lights to make finding your vehicle
even easier. To find your vehicle:
1. Press the “Location” tab on the Uconnect Mobile
App bottom bar.
2. Select the “Vehicle” icon to determine the location
of your vehicle.
3. Select the “Find Route” button that appears, once
your vehicle is located.
4. Select your preferred Navigation App to route a
path to your vehicle.
Send & Go
Send & Go allows you to search for a destination on
your mobile device and then send the route to your
vehicle’s native navigation system. To send a naviga-
tion route to your vehicle:
1. Press the “Location” tab on the Uconnect Mobile
App bottom bar.
2. Either type in the destination you would like to
navigate to, or search through one of the catego-
ries provided.
3. Select the destination you want to route to from the
list that appears.
4. Press the “Send To Vehicle” button, and then con-
firm the destination by pressing “Yes,” to send the
navigation route to the Uconnect Navigation in
your vehicle.
5. Finally, confirm the route inside your vehicle by
pressing the “Go Now” option on the pop-up that
appears on the touchscreen, when the vehicle is
started.

NOTE:
The Owner’s Mobile App content is applicable to
vehicles sold in the U.S. market and are not available
from the Canadian App Store or Google Play Store.
Key Features
• Owner Information For Your Vehicle
• Accident Assistant
• Online Service Scheduling
• Roadside Assistance
• Maintenance History
• And More
To get this FREE application, go directly to the App
Store or Google Play Store and enter the search key-
word “Chrysler”.
The Chrysler Vehicle Owner’s Information Applica-
tion is the essential app for owners of Chrysler brand
vehicles. The app puts driver and lifestyle information
right in the palm of your hand, anywhere you go.
Whether it’s providing information about specific
product features, taking a tour through your vehicle’s
equipment, staying up to date on your vehicle’s health,
knowing what steps to take following an accident, or
scheduling your next appointment, we know you’ll find
the app an important extension of your Chrysler ve-
hicle. Simply download the FREE app, select your
make and model and enjoy the ride.
Features/Benefits
• Available for free on iOS and Android smart-
phones and tablets.
• Select Chrysler brand vehicles from model year
2011 to current model year.
• You can also add other Jeep, Dodge, Ram, FIAT, or
Alfa Romeo vehicles.*
• Easy access to vehicle information anywhere you
go using categories, bookmarks, search and an A-Z
index.
• Vehicle information such as operating instructions,
maintenance, service history, vehicle controls and
emergency procedures.
• Find a dealer or an FCA-certified repair facility.
• Easily document and email an accident report.
• A parking reminder that allows you to drop a pin on
your location and navigate back to your vehicle.
• Contact customer care with one click.
• Access to vehicle heritage, parts, accessories, and
social media networks.
• Schedule your next service appointment.
• Available in English and Spanish.
*App supports selected vehicles from model year
2011 to present.
To get this FREE application, go directly to the App
Store or Google Play Store and enter the search key-
word “Chrysler”.
CHRYSLER VEHICLE
OWNER’S MOBILE APP