Cincoze DI-1000 Series User manual

Rugged Embedded Computer
6th Generation Intel® Core™ (Skylake-U)
High Performance, Compact and Modular Rugged Embedded Computer
DI-1000 Series
DOC No: DI-20170309001

DI-1000 Series
Rugged Embedded Computer | User’s Manual
2
Contents
Preface
Revision …………………………………………….……..………………..……….. 05
Copyright Notice ……………………………………………………………..……… 05
Acknowledgement …………………………………………….……….................... 05
Disclaimer ………………………………………………………….………….…….. 05
Declaration of Conformity ……………………………………….………….……… 05
Product Warranty Statement ……………………………………….……….…….. 06
Technical Support andAssistance ………………………………….……….……. 07
Conventions Used in this Manual …………………………………….…….…….. 07
Safety Precautions …..…………………………………….…………….……..….. 08
Package Contents ……………………………………………….……….………… 09
Ordering Information …..………………………………........................................ 09
Optional Modules & Accessories …..………………………………...................... 10
Chapter 1 Product Introductions
1.1 Overview ………………………………………….…………….………. 12
1.2 Highlights ………………………………………….……………………. 12
1.3 Product Pictures……..…………………………….……………………. 13
1.4 Key Features …………………..………………….…………….………. 13
1.5 Hardware Specification ………………………….……..……………… 14
1.6 System I/O ……………………………………….…………………….. 15
1.6.1 Front………………………………………………………………... 15
1.6.2 Rear………………………………………………………………… 16
1.7 Mechanical Dimension ………………………….………..……………. 17
Chapter 2 System Pin Definitions and Settings
2.1 Settings …………………………….…………………………………..... 19
2.2 Location of Connectors , Jumpers and Switches ……………………. 19
2.2.1 Top View…………………………………………………………… 19
2.2.2 Bottom View…………………………………………………......... 20
2.3 Connector / Jumper / Switch Definition…………….…..……..…….....21
2.4 Definition of Switches .……...……………......................................... 22
2.5 Definition of Connectors …..….……..……….................................... 24
Chapter 3 Optional Module Pin Definitions and Settings
3.1 CFM-IGN Power Ignition Module Connector Location.……………..... 29
3.2 Definitions of Switches…………………..………………………………. 29
Chapter 4 System Setup
4.1 Disassembling the System for Installation …………..…..…….……... 32
4.2 Installing Components on Top Side…………………....…………….... 34
4.2.1 Installing SO-DIMM Memory……………………………….......... 34
4.2.2 Installing a Mini-PCIe/mSATACard…....……………....…………35
4.2.3 InstallingAntennas………………………………………………….37
4.3 Installing Components on Bottom Side…………..…....…………….... 40
4.3.1 Installing a SATAHard Drive…....……………............................ 40
4.3.2 Installing a CFM-IGN Power Ignition Module….......…………… 41
4.3.3 Installing a High Speed CMI Module …....……...………………. 43
4.4 Assembling the System….…………………………..….…………….... 46
4.4.1 Installing Thermal Pad …………………………………………….46
4.4.2 Installing Top Cover ………………………………………………..48
4.4.3 Installing Bottom Cover ……………………………………………49
4.5 Installing Components at Front Side……………………....…….…......50
4.5.1 Removing the Front Cover Plate……………...…………………. 50
4.5.2 Installing a SATAHard Drive at Front Side …....……………….. 50

DI-1000 Series
Rugged Embedded Computer | User’s Manual
3
4.5.3 Installing a SIM Card …....…………………....………………….. 53
4.5.4 Installing the Front Cover Plate …....……………………………. 54
4.6 Wall Mount Brackets………………………….……………..…………...54
4.7 DIN-Rail Mount Brackets…………….…….………………………….... 56
4.8 VESA Mount ……………………………………………..….…………... 58
4.9 Side Mount Brackets………..…………………..……..………………... 59
Chapter 5 BIOS Setup
5.1 BIOS Introduction …….……….…………….…….…..….……………. 62
5.2 Main Setup ……..……….………………….…..….………………....... 63
5.2.1 System Date ……..…………………………………………….... 63
5.2.2 System Time ………..…………………………………………... 63
5.3 Advanced Setup ………………………………………………………… 64
5.3.1 ACPI Settings ……..……………………………………………. 64
5.3.2 AMT Configuration ……………………………………………... 65
5.3.3 PCH-FW Configuration ………………………………..………. 66
5.3.4 F81866 Super IO Configuration …………………..…………... 67
5.3.5 Hardware Monitor …………………………………………….... 68
5.3.6 S5 RTC Wake Settings …………………………..…….…….... 69
5.3.7 Serial Port Console Redirection ……………..……………..... 70
5.3.8 CPU Configuration ……………………………..………….….... 70
5.3.9 SATAConfiguration ..…………………………..…………….... 71
5.3.10 CSM Configuration ………....……………………………..….... 73
5.3.11 Asmedia SATAController Configuration………………..…..... 74
5.3.12 USB Configuration …………………………………………….… 75
5.3.13 Intel® I210 Gigabit Network Connection
Intel® Ethernet Connection I219-LM………………………….. 76
5.4 Chipset Setup …...……….………………….…..….…..…………….... 77
5.4.1 System Agent (SA) Configuration …………………………….. 77
5.4.2 PCH-IO Configuration ………………………………………….. 78
5.5 Security Setup …...……….………………….…..….…..…………….... 81
5.5.1 Administrator Password …….………………………………….. 81
5.5.2 User Password …….………………………………………..….. 81
5.6 Boot Setup …...……….….………………….…..….…..………..…….. 82
5.6.1 Setup Prompt Timeout………………………………………….. 82
5.6.2 Bootup NumLock State ………………………………………… 82
5.6.3 Quiet Boot ………………………………………………….……. 82
5.6.4 Fast Boot ……………..…………………………………………. 82
5.6.5 New Boot Option Policy …….…………………………….……. 82
5.6.6 Hard Drive BBS Priority.…………………………………….……82
5.7 Save & Exit …...……….….………………….…..….…..…………….... 83
5.7.1 Save Changes and Exit ………………..……………………...... 83
5.7.2 Discard Changes and Exit ……………………………………….83
5.7.3 Save Changes and Reset ………………………………………. 83
5.7.4 Discard Changes and Reset ….………………………………… 83
5.7.5 Save Changes …………………………………………………… 83
5.7.6 Discard Changes ………………………………………………… 83
5.7.7 Restore Defaults ………………………….……………………… 83
5.7.8 Save as User Defaults ………………..………………………… 83
5.7.9 Restore User Defaults ..………………….……………………… 83

DI-1000 Series
Rugged Embedded Computer | User’s Manual
4
Chapter 6 Product Application
6.1 Digital I/O (DIO) Application……………………….…..….……………..85
6.1.1 Digital I/O Programming Guide ………………………………... 85
6.2 (DIO) Hardware Specification ……………………………………..….. 90
6.2.1 DIO Connector Definitions ..….……………………………….... 91

DI-1000 Series
Rugged Embedded Computer | User’s Manual
5
Revision
Preface
Revision Description Date
1.0 New Release 2017/03/09
Copyright Notice
© 2016 by Cincoze Co., Ltd. All rights are reserved. No parts of this manual may be copied, modified,
or reproduced in any form or by any means for commercial use without the prior written permission of
Cincoze Co., Ltd. All information and specification provided in this manual are for reference only and
remain subject to change without prior notice.
Acknowledgement
Cincoze is a registered trademark of Cincoze Co., Ltd. All registered trademarks and product names
mentioned herein are used for identification purposes only and may be trademarks and/or registered
trademarks of their respective owners.
Disclaimer
This manual is intended to be used as a practical and informative guide only and is subject to change
without notice. It does not represent a commitment on the part of Cincoze. This product might include
unintentional technical or typographical errors. Changes are periodically made to the information
herein to correct such errors, and these changes are incorporated into new editions of the publication.
Declaration of Conformity
FCC
This equipment has been tested and found to comply with the limits for a ClassA digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
CE
The product(s) described in this manual complies with all application European Union
(CE) directives if it has a CE marking. For computer systems to remain CE compliant,
only CE-compliant parts may be used. Maintaining CE compliance also requires proper
cable and cabling techniques.

DI-1000 Series
Rugged Embedded Computer | User’s Manual
6
Product Warranty Statement
Warranty
Cincoze products are warranted by Cincoze Co., Ltd. to be free from defect in materials and
workmanship for 2 years from the date of purchase by the original purchaser.
During the warranty period, we shall, at our option, either repair or replace any product that proves to
be defective under normal operation.
Defects, malfunctions, or failures of the warranted product caused by damage resulting from natural
disasters (such as by lightening, flood, earthquake, etc.), environmental and atmospheric disturbances,
other external forces such as power line disturbances, plugging the board in under power, or incorrect
cabling, and damage caused by misuse, abuse, and unauthorized alteration or repair, and the product
in question is either software, or an expendable item (such as a fuse, battery, etc.), are not warranted.
RMA
Before sending your product in, you will need to fill in Cincoze RMA Request Form and obtain a RMA
number from us. Our staff is available at any time to provide you with the most friendly and immediate
service.
RMA Instruction
Customers must fill in Cincoze Return MerchandiseAuthorization (RMA) Request Form and
obtain a RMA number prior to returning a defective product to Cincoze for service.
Customers must collect all the information about the problems encountered and note anything
abnormal and describe the problems on the “Cincoze Service Form” for the RMA number apply
process.
Charges may be incurred for certain repairs. Cincoze will charge for repairs to products whose
warranty period has expired. Cincoze will also charge for repairs to products if the damage
resulted from acts of God, environmental or atmospheric disturbances, or other external forces
through misuse, abuse, or unauthorized alteration or repair. If charges will be incurred for a
repair, Cincoze lists all charges, and will wait for customer’s approval before performing the
repair.
Customers agree to insure the product or assume the risk of loss or damage during transit, to
prepay shipping charges, and to use the original shipping container or equivalent.
Customers can be send back the faulty products with or without accessories (manuals, cable,
etc.) and any components from the system. If the components were suspected as part of the
problems, please note clearly which components are included. Otherwise, Cincoze is not
responsible for the devices/parts.
Repaired items will be shipped along with a "Repair Report" detailing the findings and actions
taken.
Limitation of Liability
Cincoze’ liability arising out of the manufacture, sale, or supplying of the product and its use, whether
based on warranty, contract, negligence, product liability, or otherwise, shall not exceed the original
selling price of the product. The remedies provided herein are the customer’s sole and exclusive
remedies. In no event shall Cincoze be liable for direct, indirect, special or consequential damages
whether based on contract of any other legal theory.

DI-1000 Series
Rugged Embedded Computer | User’s Manual
7
Technical Support and Assistance
1. Visit the Cincoze website at www.cincoze.com where you can find the latest information about the
product.
2. Contact your distributor or our technical support team or sales representative for technical support
if you need additional assistance. Please have following information ready before you call:
Product name and serial number
Description of your peripheral attachments
Description of your software (operating system, version, application software, etc.)
A complete description of the problem
The exact wording of any error messages
Conventions Used in this Manual
This indication alerts operators to an operation that, if not strictly
observed, may result in severe injury.
WARNING
This indication alerts operators to an operation that, if not strictly
observed, may result in safety hazards to personnel or damage to
equipment.
CAUTION
This indication provides additional information to complete a task easily.
NOTE

DI-1000 Series
Rugged Embedded Computer | User’s Manual
8
Safety Precautions
Before installing and using this device, please note the following precautions:
1. Read these safety instructions carefully.
2. Keep this User’s Manual for future reference.
3. Disconnected this equipment from any AC outlet before cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and must be
easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause
damage.
7. Make sure the voltage of the power source is correct before connecting the equipment to the
power outlet.
8. Use a power cord that has been approved for using with the product and that it matches the
voltage and current marked on the product’s electrical range label.The voltage and current rating
of the cord must be greater than the voltage and current rating marked on the product.
9. Position the power cord so that people cannot step on it. Do not place anything over the power
cord.
10.All cautions and warnings on the equipment should be noted.
11.If the equipment is not used for a long time, disconnect it from the power source to avoid damage
by transient overvoltage.
12.Never pour any liquid into an opening. This may cause fire or electrical shock.
13.Never open the equipment. For safety reasons, the equipment should be opened only by qualified
service personnel.
If one of the following situations arises, get the equipment checked by service personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it work according to the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
14. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer.

DI-1000 Series
Rugged Embedded Computer | User’s Manual
9
Package Contents
Before installation, please ensure all the items listed in the following table are included in the package.
Item Description Q’ty
1 Embedded System 1
2 CPU Heatsink Thermal Pad 1
3 Utility DVD Driver 1
4 Screw Pack 1
5 Wall Mounting Kit 1
6 Power Terminal Block Connector 1
7 Remote Power On/Off Terminal Block Connector 1
8 DIO Terminal Block Connector 2
9 DVI-I to VGAAdaptor 1
Note: Notify your sales representative if any of the above items are missing or damaged.
Ordering Information
Model No. Product Description
DI-1000-i5 6th Generation Intel® Core™ i5-6300U High Performance, Compact
and Modular Rugged Embedded Computer

DI-1000 Series
Rugged Embedded Computer | User’s Manual
10
Model No. Description
CFM-IGN102 CFM Module with Power Ignition Sensing Control Function, Selectable 12V/24V (68 x 25 mm)
CMI-LAN104/UB0712 CMI Module with 4x Intel GbE LAN, RJ45 Port, 1x Universal Bracket (82.5 x 19.5 mm)
CMI-PoE114/UB0712 CMI Module with 4x PoE+, Intel GbE LAN, RJ45 Port, Individual Port 25.5W, 1x Universal Bracket
(82.5 x 19.5 mm)
CMI-M12LAN104/UB0710 CMI Module with M12 Connector, 4x Intel GbE LAN, 1x Universal Bracket (82.5 x 19.5 mm)
CMI-M12PoE114/UB0710 CMI Module with M12 Connector, 4x PoE+, Intel GbE LAN, Individual Port 25.5W, 1x Universal
Bracket (82.5 x 19.5 mm)
MEC-COM-M212/UB0703 Mini-PCIe Module with 2x COM Ports, 2x Universal Brackets (82.5 x 19.5 mm)
MEC-FIR-M003/UB0701 Mini-PCIe Module with 1x 1394A Port, 2x 1394B Ports, 1x Universal Bracket (82.5 x 19.5 mm)
MEC-LAN-M002-R1
/UB0711 Mini-PCIe Module with 2x LAN Ports, 1x Universal Bracket (82.5 x 19.5 mm)
MEC-USB-M002
/UB0714/CB0101 Mini-PCIe Module with 2x USB 3.0 Ports, 1x Universal Bracket (82.5 x 19.5 mm), 1x Cable for
MEC-USB (15cm)
DIN01 DIN-RAIL Mount Kit, KMRH-K175
SIDE01 SIDE Mount Kit (175 x 51.6 x 60 mm)
GSM60A12-CIN1 Adapter AC/DC 12V 5A 60W with 3pin Terminal Block Plug 5.0mm Pitch, with Tubes
GS120A24-CIN1 Adapter AC/DC 24V 5A 120W with 3pin Terminal Block Plug 5.0mm Pitch, with Tubes
Optional Modules & Accessories

Product Introductions
Chapter 1

DI-1000 Series
Rugged Embedded Computer | User’s Manual
12
1.1 Overview
1.2 Highlights
Cincoze DI-1000 Series is a high-performance, compact and modular fanless embedded
computer powered by 6th generation Intel® Core™ mobile processor (Skylake-U), it integrates
Intel® HD graphic engine and accommodates one DDR4 socket up to 16 GB which allows DI-
1000 Series to fulfill all kinds of high-end computing demands. Extremely compact size with
dimension 203 x 142 x 66.8 mm, comprising unbeatable I/O such as DVI-I, DP, 2x LAN, 6x COM,
6x USB, 8x Optical Isolated DIO, PS/2, Mic-in, Line-out, and remote power on/off switch,
supporting two full-size Mini-PCIe slots for wireless communication and I/O expansion,
accommodating two 2.5” SATA HDD/SSD bay for RAID 0/1 function, making DI-1000 series
unmatchable in the market for its size and functions. DI-1000 Series weighs only 1.65 kg
supporting 4 types of mounting mechanisms (Wall, DIN, Side and VESA) allowing it to be
installed everywhere. The unique Cincoze’s CMI (Combined Multiple I/O), CFM (Control
Function Module) and MEC (Mini-PCIe Card) technologies allow DI-1000 Series to be expanded
according to the specific needs. The options of ready-to-use modules including Multi-LAN, PoE,
M12 connections, Power Ignition Sensing and various types of I/O interface, making DI-1000
series application-ready platform for factory automation, machine vision, in-vehicle, and mobile
surveillance applications.
High Performance
• Onboard 6th Generation Intel® Core™ Mobile Processor
• Performance Enhanced by Intel® 14 nm Technology
• Extremely Low Power Consumption 15W TDP
• Intel® HD Graphics Supports Triple Independent Display
Resolution Up to Ultra HD 4K
Compact Size
• Compact Size 203 x 142 x 66.8 mm with Light Weight 1.65 kg
• Rich I/O for Greater Device Connectivity (DVI, DisplayPort, 2x
GbE LAN, 6x COM, 6x USB, 8x Optical Isolated DIO, PS/2
Modular Design
• CMI (Combined Multiple I/O) Technology for LAN, PoE and
M12 X-Coding Connector Expansion
• CFM (Control Function Module) Technology for Power
Ignition Sensing (IGN) Function Expansion
• Mini-PCIe Module Kits for Various I/O Expansion

DI-1000 Series
Rugged Embedded Computer | User’s Manual
Rear
13
1.3 Product Pictures
Front
• Onboard 6th Generation Intel® Core™ Mobile Processor (BGA Type)
• 1x DDR4 SO-DIMM Socket, 2133MHz, Supports Up to 16 GB
• Triple Independent Display (DVI-I, DisplayPort)
• Compact Size 203 x 142 x 66.8 mm with Light Weight 1.65 kg
• 1x Hot-swappable 2.5” SATA HDD/SSD Bay and 1x Internal 2.5” SATA HDD/SSD Bay, Supports RAID 0/1
• Rich I/O Including DVI, DP, 2x GbE LAN, 6x COM, 6x USB, 8x Optical Isolated DIO
• Supports Cincoze CMI Technology for LAN, PoE & M12 X-Coding Connector Expansion
• Supports Cincoze CFM Technology for Power Ignition Sensing (IGN) Function Expansion
• Cincoze MEC Module Kits for Various I/O Expansion
• 2x Full-size Mini-PCIe Slots for Wireless and I/O Expansion
• Wide Operating Temperature (-40°C to 70°C)
• EN50155 & E-Mark* for Railway & In-vehicle Applications (*Pending)
1.4 Key Features

DI-1000 Series
Rugged Embedded Computer | User’s Manual
14
System
Processor
• Onboard Intel® Core™ i5-6300U Processor
(3M Cache, up to 3.00 GHz, 15W TDP)
Chipset
• SoC
BIOS
• AMI 8Mbit SPI BIOS
Memory
• 1x DDR4 260-pin SO-DIMM Socket, Support up to 16 GB
(2133MHz, Un-buffered and Non-ECC type)
Graphics
• Integrated Intel® HD Graphics
• Three Independent Display
Audio
• Realtek® ALC888-GR
• High Definition Audio
I/O Interface
• 1x DVI-I Connector, Resolution 1920 x 1080
• 1x DisplayPort Connector, Resolution 3840 x 2160
• 2x GbE LAN (Support Wake-on-LAN, Teaming, Jumbo Frame,
IEEE 1588v2 and PXE), RJ45
- GbE1: Intel I210AT
- GbE2: Intel I219LM
• 6x RS-232/422/485 with Auto Flow Control (Support 5V/12V), DB9
• 4x USB 3.0 (Type-A) & 2x USB 2.0 (Type-A)
• 1x PS/2, 6-Pin Mini-DIN Female Connector
• 8x Optical Isolated DIO (4x DI, 4x DO), 10-Pin Terminal Block
Support 5~48V
• 1x Line-out, Phone Jack 3.5mm
• 1x Mic-in, Phone Jack 3.5mm
• 1x ATX Power On/Off Button
• 1x AT/ATX Mode Switch
• 1x Clear CMOS Switch
• 1x Remote Power On/Off Connector, 2-Pin Terminal Block
Storage
• 2x 2.5” SATA HDD/SSD Bay, Support RAID 0/1 (Gen3)
(One Internal, One Front Accessible & Hot-swappable)
• 2x mSATA (shared by Mini-PCIe socket) (Gen2)
Expansion
• 1x CFM Interface for Cincoze CFM Modules
• 1x CMI Interfaces for Cincoze CMI Modules
• 2x Full-size Mini-PCIe Sockets for Wireless & I/O Expansion
• 1x SIM Socket
1.5 Hardware Specification
Other Function
• Support CFM (Control Function Module) Technology
• Support CMI (Combined Multiple I/O) Technology
• Support Instant Reboot Technology (0.2 sec)
• SuperCap Integrated for CMOS Battery Maintenance-free
• Watchdog Timer: Software Programmable Supports 1~255
sec. System Reset
Power Requirement
• Support AT/ATX Power Type
• Power Input Voltage 9~48VDC
• One 3-Pin Terminal Block Connector
• Optional Power Adapter AC/DC 12V/5A 60W or 24V/5A 120W
Physical
• Dimension (WxDxH): 203 x 142 x 66.8 mm
• Weight: 1.65 kg
• Extruded Aluminum with Heavy Duty Metal
• Support Wall / Side / DIN-RAIL / VESA Mounting
• Fanless Design
• Cable-less Design
• Unibody Chassis
• Jumper-less Design
Protection
• Reverse Power Input Protection
• Over Voltage Protection: 58V
• Over Current Protection: 15A
• ESD Protection: +/-15kV (air), +/-8kV (contact)
• Surge Protection: 3kW
MTBF
• Time: 360,145 Hours
• Calculation Model: Telcordia SR-332 Issue 3, Method 1, Case 3
• Environment: GB, GC
• Temperature: 40°C
Operating System
• Windows® 10
• Windows® 8.1
• Windows® 7
Environment
• Operating Temperature: -40°C to 70°C
(With extended temperature peripherals; Ambient with air flow;
According to IEC60068-2-1, IEC60068-2-2, IEC60068-2-14)
• Storage Temperature: -40°C to 85°C
• Relative Humidity: 95% RH @ 40°C (Non-condensing)
• Shock: Operating, 50 Grms, Half-sine 11 ms Duration
(w/ SSD, according to IEC60068-2-27)
• Vibration: Operating, 5 Grms, 5-500 Hz, 3 Axes
(w/ SSD, according to IEC60068-2-64)
• EMC: CE, FCC Class A
• Railway: EN50155, EN50121-3-2
• In-vehicle: E-Mark (Pending)

DI-1000 Series
Rugged Embedded Computer | User’s Manual
1.6.1 Front
15
1.6 System I/O
ATX Power On/Off Button
Press to power-on or power-off the system
AT/ATX Mode Select Switch
Used to select AT or ATX power mode
Power LED
Indicates the power status of the system
HDD LED
Indicates the status of the hard drive
USB 2.0 Port
Used to connect USB 2.0/1.1 device
SIM Card Slot
Used to inserts a SIM card
IGN Setting Switch
Used to set up IGN function
Clear CMOS Switch
Used to clear CMOS to reset BIOS
Removable 2.5” SATA HDD/SSD Bay
Used to inserts a 2.5” HDD/SSD
Mic-in
Used to connect a microphone
Line-out
Used to connect a speaker
COM Port
COM #3 ~ COM #6 support RS232/422/485
serial device
Remote Power On/Off Terminal Block
Used to plug a remote power on/off terminal
block
Universal I/O Bracket
Used to customized I/O output with optional
modules

DI-1000 Series
Rugged Embedded Computer | User’s Manual
1.6.2 Rear
16
DC IN Terminal Block
Used to plug a DC power input with terminal
block
DVI-I Port
Used to connect a DVI monitor or connect
optional split cable for dual display mode
DisplayPort Port
Used to connect the system with DisplayPort
monitor
PS/2 Port
Used to connect the PS/2 device
LAN Port
Used to connect the system to a local area
network
USB 3.0 Port
Used to connect USB 3.0/2.0/1.1 device
COM Port
COM #1 ~ COM #2 support RS232/422/485
serial device
Digital I/O Terminal Block
The Digital I/O terminal block supports 4
digital input and 4 digital output
Antenna Hole
Used to install an antenna jack

DI-1000 Series
Rugged Embedded Computer | User’s Manual
Unit: mm
17
1.7 Mechanical Dimension

System Pin Definitions and
Settings
Chapter 2

DI-1000 Series
Rugged Embedded Computer | User’s Manual
19
2.1 Settings
When setting the jumpers, ensure that the jumper caps are placed on the correct pins. When
the jumper cap is placed on both pins, the jumper is short. If you remove the jumper cap, or
place the jumper cap on just one pin, the jumper is open. Refer to below for examples of the 2-
pin and 3-pin jumpers when they are short (on) and open (off).
1 2
Open
1 2
Short
Two-Pin Jumpers
1 2 3
Pins 1 and 2 are short
1 2 3
All pins are open 1 2 3 Pins 2 and 3 are short
Three-Pin Jumpers
2.2 Location of the Connectors, Jumpers and Switches
2.2.1 Top View

DI-1000 Series
Rugged Embedded Computer | User’s Manual
20
2.2.2 Bottom View