Cincoze P2000 Series User manual

CN-TB-QP22-44_V1.0
Convertible Embedded Computer
Convertible Embedded Computer
6th Generation Intel® Core™ U Series (Skylake)
Fanless Computer with CFM & CDS Interface
P2000 Series
DOC No: P2000_R1.30_20180129001

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0 2
Contents
Preface
Revision …………………………………………….……..……………….……….. 04
Copyright Notice …………………………………………………………………… 04
Acknowledgement …………………………………………….………................... 04
Disclaimer ………………………………………………………….……………….. 04
Declaration of Conformity ……………………………………….………………… 04
Product Warranty Statement ……………………………………….…………….. 05
Technical Support and Assistance ………………………………….……………. 06
Conventions Used in this Manual …………………………………….………….. 06
Safety Precaution …..…………………………………….…………….………….. 07
Package Contents ……………………………………………….……….………… 08
Ordering Information …………………………………………….……….………… 08
Optional Accessories …………...……………………………………...................... 09
Chapter 1 Product Introductions
1.1 Overview ………………………………………….…………………….. 11
1.2 Highlights ………………………………………….…………………….. 11
1.3 Product Pictures……..…………………………….…………………….. 12
1.4 Key Features …………………..………………….…………………….. 12
1.5 Hardware Specification ………………………….……..……………… 13
1.6 System I/O ……………………………………….……………………… 14
1.3.1 Front ……………………………………………………………… 14
1.3.2 Rear ………….………………………………….………………... 14
1.3.3 Left …………………………………………..….………………... 15
1.3.4 Right …………………………………………….………………... 15
1.3.5 Top ………………………………..….…….…………………….. 16
1.7 Mechanical Dimension ………………………….………..……………. 17
Chapter 2 Jumpers, Switches and Connectors
2.1 Jumper Settings …………………………….………………………..... 19
2.2 Location of Jumpers, Switches and Connectors ………….……….... 19
2.2.1 Top View ……………………………….………………………… 19
2.2.2 Bottom View …………………………………………………….. 20
2.3 List of Jumpers, Connectors and Switches ……….…..….………..... 21
2.4 Definition of Switches .……...……………........................................ 22
2.5 Definition of Connectors …..….……..………................................... 26
Chapter 3 System Setup
3.1 Removing the Top Cover ……...…………………………..…………... 38
3.2 Installing a Half Size Mini PCIe Card ……………………………….... 39
3.3 Installing a Full Size Mini PCIe Card ………………....…………….... 40
3.4 Installing a mSATA Card ………………….…………....…………….... 41
3.5 Installing Antennas …………………………………..….…………….... 42
3.6 Installing a SO-DIMM Module ……………………………....…….….... 44
3.7 Installing a PCI(e) Card ……………………………..….……………... 45
3.8 Installing Thermal Pad of Thermal Block………….….…………….... 47
3.9 Installing a Power Ignition Daughter Board (Optional) …………….... 48
3.10 Installing a PoE Daughter Board (Optional) …..…..….……………... 49
3.11 Installing the Top Cover ………………………...…..….…………….... 50
3.12 Installing a SATA Hard Drive at Front Pane………..….……………… 51
3.13 Installing a SATA Hard Drive on Bottom Side …..…….……………... 54
3.14 Installing a SIM Card ……………………….………..….……………… 56

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0 3
3.15 Installing a CFast Card ………….…..……..………..….……………... 57
3.16 Connecting with CV Display Module……………..….……………...... 58
3.17 VESA Mount ………………....……..……….…..….…………………... 61
3.18 Wall Mount ………………….……..……….…..….………………..…... 62
Chapter 4 BIOS Setup
4.1 BIOS Introduction …….……….…………….…….…..….…………... 65
4.2 Main Setup ……..……….………………….…..….………………...... 66
4.2.1 System Date …….…………………………………………….... 66
4.2.2 System Time ………..…………………………………………... 66
4.3 Advanced Setup ……………………………………………………….. 67
4.3.1 ACPI Settings ……..……………………………………………. 67
4.3.2 AMT Configuration ……………………………………………... 68
4.3.3 PCH-FW Configuration ………………………………..………. 69
4.3.4 F81866 Super IO Configuration …………………..…………... 70
4.3.5 Hardware Monitor …………………………………………….... 71
4.3.6 S5 RTC Wake Settings …………………………..………….... 72
4.3.7 Serial Port Console Redirection ……………..……………..... 73
4.3.8 CPU Configuration ……………………………..………….….... 73
4.3.9 SATA Configuration ..…………………………..……………..... 74
4.3.10 CSM Configuration ……..………………………………..…..... 76
4.3.11 Asmedia SATA Controller Configuration ………………..….... 78
4.3.12 USB Configuration …………………………………………….. 79
4.4 Chipset Setup …...……….………………….…..….…..……………... 80
4.4.1 System Agent (SA) Configuration …………………………….. 80
4.4.2 PCH-IO Configuration ………………………………………….. 81
4.5 Security Setup …...……….………………….…..….…..……………... 83
4.5.1 Administrator Password …….………………………………….. 83
4.5.2 User Password …….………………………………………..….. 83
4.5.3 HDD Security Configuration ………………………………..….. 83
4.6 Boot Setup …...……….….………………….…..….…..………..……... 84
4.6.1 Setup Prompt Timeout………………………………………….. 84
4.6.2 Bootup NumLock State ………………………………………….84
4.6.3 Quiet Boot ………………………………………………….……. 84
4.6.4 Boot Option ………………….………………………………….. 84
4.6.5 Fast Boot ……………..…………………………………………. 84
4.6.6 New Boot Option Policy …….…………………………….……. 84
4.6.7 Hard Drive BBS Priorities …..…………………………………. 84
4.7 Save & Exit …...……….….………………….…..….…..…………….... 85
4.7.1 Save Changes and Exit ………………..……………………...... 85
4.7.2 Discard Changes and Exit ………………………………………. 85
4.7.3 Save Changes and Reset ………………………………………. 85
4.7.4 Discard Changes and Reset ….………………………………… 85
4.7.5 Save Changes …………………………………………………… 85
4.7.6 Discard Changes ………………………………………………… 85
4.7.7 Restore Defaults ………………………….……………………… 85
4.7.8 Save as User Defaults ………………..………………………… 85
4.7.9 Restore User Defaults ..………………….……………………… 85
Chapter 5 Product Application
5.1 Digital I/O (DIO) application …..…………………….…..….………….. 87
5.1.1 Digital I/O Programming Guide ………………………………... 87
5.2 P2000 Digital I/O (DIO) Hardware Specification …………………….. 95
5.2.1 P2000 DIO Connector Definition ……………………………..... 96

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0 4
Revision
Preface
Revision
Description
Date
1.0
New
Release
2016/09/21
1.1
IGN Board Pin Define (CFM
-IGN100 Only) Revised
2016/11/07
1.2
Added 1.5
support dimension of add-on card
2016/06/21
1.21
Modified the table and sample code of DIO
2017/12/04
1.30
Modified steps of system Setup
2018/01/29
1.40
Modified
P2002-i3 Series Products Information
2018/09/07
Copyright Notice
© 2014 by Cincoze Co., Ltd. All rights are reserved. No parts of this manual may be copied, modified,
or reproduced in any form or by any means for commercial use without the prior written permission of
Cincoze Co., Ltd. All information and specification provided in this manual are for reference only and
remain subject to change without prior notice.
Acknowledgement
Cincoze is a registered trademark of Cincoze Co., Ltd. All registered trademarks and product names
mentioned herein are used for identification purposes only and may be trademarks and/or registered
trademarks of their respective owners.
Disclaimer
This manual is intended to be used as a practical and informative guide only and is subject to change
without notice. It does not represent a commitment on the part of Cincoze. This product might include
unintentional technical or typographical errors. Changes are periodically made to the information
herein to correct such errors, and these changes are incorporated into new editions of the publication.
Declaration of Conformity
FCC
This equipment has been tested and found to comply with the limits for a Class Adigital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
CE
The product(s) described in this manual complies with all application European Union
(CE) directives if it has a CE marking. For computer systems to remain CE compliant,
only CE-compliant parts may be used. Maintaining CE compliance also requires proper
cable and cabling techniques.

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0 5
Product Warranty Statement
Warranty
Cincoze products are warranted by Cincoze Co., Ltd. to be free from defect in materials and
workmanship for 2 years from the date of purchase by the original purchaser.
During the warranty period, we shall, at our option, either repair or replace any product that proves to
be defective under normal operation.
Defects, malfunctions, or failures of the warranted product caused by damage resulting from natural
disasters (such as by lightening, flood, earthquake, etc.), environmental and atmospheric disturbances,
other external forces such as power line disturbances, plugging the board in under power, or incorrect
cabling, and damage caused by misuse, abuse, and unauthorized alteration or repair, and the product
in question is either software, or an expendable item (such as a fuse, battery, etc.), are not warranted.
RMA
Before sending your product in, you will need to fill in Cincoze RMA Request Form and obtain a RMA
number from us. Our staff is available at any time to provide you with the most friendly and immediate
service.
◼RMA Instruction
⚫Customers must fill in Cincoze Return MerchandiseAuthorization (RMA) Request Form and
obtain a RMA number prior to returning a defective product to Cincoze for service.
⚫Customers must collect all the information about the problems encountered and note anything
abnormal and describe the problems on the “Cincoze Service Form” for the RMA number apply
process.
⚫Charges may be incurred for certain repairs. Cincoze will charge for repairs to products whose
warranty period has expired. Cincoze will also charge for repairs to products if the damage
resulted from acts of God, environmental or atmospheric disturbances, or other external forces
through misuse, abuse, or unauthorized alteration or repair. If charges will be incurred for a
repair, Cincoze lists all charges, and will wait for customer’s approval before performing the
repair.
⚫Customers agree to insure the product or assume the risk of loss or damage during transit, to
prepay shipping charges, and to use the original shipping container or equivalent.
⚫Customers can be send back the faulty products with or without accessories (manuals, cable,
etc.) and any components from the system. If the components were suspected as part of the
problems, please note clearly which components are included. Otherwise, Cincoze is not
responsible for the devices/parts.
⚫Repaired items will be shipped along with a "Repair Report" detailing the findings and actions
taken.
Limitation of Liability
Cincoze’ liability arising out of the manufacture, sale, or supplying of the product and its use, whether
based on warranty, contract, negligence, product liability, or otherwise, shall not exceed the original
selling price of the product. The remedies provided herein are the customer’s sole and exclusive
remedies. In no event shall Cincoze be liable for direct, indirect, special or consequential damages
whether based on contract of any other legal theory.

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0 6
Prefaces
This indication alerts operators to an operation that, if not strictly
observed, may result in severe injury.
WARNING
This indication alerts operators to an operation that, if not strictly
observed, may result in safety hazards to personnel or damage to
equipment.
CAUTION
This indication provides additional information to complete a task easily.
NOTE
Technical Support and Assistance
1. Visit the Cincoze website at www.cincoze.com where you can find the latest information about the
product.
2. Contact your distributor or our technical support team or sales representative for technical support
if you need additional assistance. Please have following information ready before you call:
⚫Product name and serial number
⚫Description of your peripheral attachments
⚫Description of your software (operating system, version, application software, etc.)
⚫A complete description of the problem
⚫The exact wording of any error messages
Conventions Used in this Manual

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0 7
Safety Precautions
Before installing and using this device, please note the following precautions:
1. Read these safety instructions carefully.
2. Keep this User’s Manual for future reference.
3. Disconnected this equipment from any AC outlet before cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and must be
easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause
damage.
7. Make sure the voltage of the power source is correct before connecting the equipment to the
power outlet.
8. Use a power cord that has been approved for using with the product and that it matches the
voltage and current marked on the product’s electrical range label. The voltage and current rating
of the cord must be greater than the voltage and current rating marked on the product.
9. Position the power cord so that people cannot step on it. Do not place anything over the power
cord.
10.All cautions and warnings on the equipment should be noted.
11.If the equipment is not used for a long time, disconnect it from the power source to avoid damage
by transient overvoltage.
12.Never pour any liquid into an opening. This may cause fire or electrical shock.
13.Never open the equipment. For safety reasons, the equipment should be opened only by qualified
service personnel.
If one of the following situations arises, get the equipment checked by service personnel:
⚫The power cord or plug is damaged.
⚫Liquid has penetrated into the equipment.
⚫The equipment has been exposed to moisture.
⚫The equipment does not work well, or you cannot get it work according to the user's manual.
⚫The equipment has been dropped and damaged.
⚫The equipment has obvious signs of breakage.
14. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer.

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0 8
Package Contents
Before installation, please ensure all the items listed in the following table are included in the package.
Item
Description
Q’ty
1
P2002 / P2002E System
1
2
Utility DVD Driver
1
3
Screw Pack
1
4
Wall / CDS Mounting Kit
1
5
Power Terminal Block Connector
1
6
Fan Terminal Block Connector
1
7
DIO Terminal Block Connector
2
8
Remote Power On/Off Terminal Block Connector
1
Note: Notify your sales representative if any of the above items are missing or damaged.
Ordering Information
Model No.
Product Description
P2002-i5-R10 Intel® 6th Generation Core™ i5-
6300U Fanless Computer with CFM and
CDS Interface
P2002E-i5-R10 Intel® 6th Generation Core™ i5-6300U Expandable Fanless Computer
with CFM and CDS Interface
P2002E-i5-E4-R10 Intel® 6th Generation Core™ i5-6300U Expandable Fanless Computer
with CFM and CDS Interface, 1x PCIex4 Expansion
P2002E
-i5-PI-R10 Intel® 6th Generation Core™ i5-6300U Expandable Fanless Computer
with CFM and CDS Interface, 1x PCI Expansion
P2002-i3-R10 Intel® 6th Generation Core™ i3-
6100U Fanless Computer with CFM and
CDS Interface
P2002E-i3-R10 Intel® 6th Generation Core™ i3-6100U Expandable Fanless Computer
with CFM and CDS Interface
P2002E-i3-E4-R10 Intel® 6th Generation Core™ i3-6100U Expandable Fanless Computer
with CFM and CDS Interface, 1x PCIex4 Expansion
P2002E
-i3-PI-R10 Intel® 6th Generation Core™ i3-6100U Expandable Fanless Computer
with CFM and CDS Interface, 1x PCI Expansion

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0 9
Optional Accessories
Model No.
Product Description
CFM-IGN100-R10 Power Ignition Sensing Control Function Module
CFM-PoE100-R10 PoE Control Function Module, individual port 25.5W (50 x 44 x 15 mm)
(For P2002 only)
CFM-PoE101-R10 PoE Control Function Module, individual port 25.5W (50 x 44 x 33 mm)
(For P2002E only)
MEC
-COM-M212-05 Mini-PCIe module with 2x RS-
232 Serial Ports, 1x Universal bracket (154
x 17 x 11 mm)
MEC
-COM-M334-05 Mini-PCIe module with 4x RS-232/422/485 Serial Ports,1x Universal
bracket (154 x 17 x 11 mm)
MEC
-LAN-M002-05 Mini-
PCIe module with 2x LAN Ports, 1x Universal bracket (154 x 17 x 11
mm)
MEC
-USB-M002-05 Mini-
PCIe module with 2x USB 3.0 Ports, 1x Universal bracket (154 x 17 x
11 mm)
MEC
-FIR-M003-05 Mini-PCIe module with 1x 1394APort, 2x 1394B Ports, 1x Universal
bracket (154 x 17 x 11 mm)
RC
-E4-100-R10 Riser Card 1 x PCIex4 (For P2002E only)
RC
-PI-100-R10 Riser Card 1 x PCI (For P2002E only)

Product Introductions
Chapter 1

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0 11
1.1 Overview
1.2 Highlights
Cincoze P2002/P2002Eis a high performance fanless embedded and display computer
powered by Intel® 6th generation Core™ U series processor with only 15 watt power
consumption. The advanced graphics engine supports triple independent display with 1x VGA,
1x DVI-D and 1x CDS interface. P2002/P2002E provides great connectivity with rich I/O
including 2x GbE LAN, 5x USB and 6x COM ports. P2002/P2002E also supports 3 types of
storage devices including 2.5" SATA HDD, CFast and mSATA. The accessible design of these
storage devices allows quick data access and easy maintenance.
P2002/P2002E supports CFM Technology which allows you to extend PoE and IGN function
with additional modules. And thanks to Cincoze’s exclusive CDS Technology, P2002/P2002E
also acts as an engine of panel PC for CV-100 Series.
P2002/P2002E is truly a rugged computing system by supporting wide operating temperature
from -25°Cto 70°C, wide range DC power input from 9V to 48V, high tolerance of shock and
vibration, various kinds of industrial protection and the integrated SuperCap for battery
maintenance-free, those features allow P2002/P2002Eto be easily deployed in harsh
environment and critical applications.
CDS Technology
CDS (Convertible Display Systems) is patented technology from Cincoze, which is a
revolutionary panel PC solution that offers features of modular design, configured on demand,
scalability, transformability and Plug & Play.
CFM Technology
CFM (Control Function Module) is a technology created by Cincoze, it enables function
enhancement by adding specific function daughter board. CFM Technology allows
P2002/P2002E to support PoE and IGN function for various applications.
Instant Reboot
P2002/P2002E supports 0.2 second instant reboot for critical application.
SuperCap
SuperCap is extremely high volume capacitor, which can be recharged automatically when
power is connected (without power Min. 50 days /Max. 70 days), you never need to change
CMOS battery, and it makes P2002/P2002E a truly reliable and maintenance-free system.

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0
P2002E
12
1.3 Product pictures
Front
Rear
Side (Left)
Side (Right)
P2002
Front
Rear
Side (Left)
Side (Right)
• Onboard Intel® 6th Generation Core™ U Series Processor (15W)
• 2x DDR4 SO-DIMM Socket, Support Up to 32 GB
• Advanced Graphics Engine Support Triple Independent Display
• 2x 2.5” SATA HDD Bay, 1x mSATA and 1x CFast Socket
• 2x Full Size Mini-PCIe Socket
• 1x PCI or 1x PCIex4 Socket (For P2002E only)
• Support CFM (Control Function Module) Technology
• Support 2x PoE+, Individual Port Offers Max. 25.5W (with optional CFM module)
• Support Ignition Sensing Function (IGN) (with optional CFM module)
• Rich I/O (2x GbE LAN, 6x COM, 5x USB, 16x Isolated DIO)
• Support Instant Reboot Technology
• Support CDS Technology for Convertible Panel PC
• Wide Operating Temperature (-25°C to 70°C)
• SuperCap integrated for Battery Maintenance-Free
1.4 key Features

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0 13
Processor System
• Onboard 6th Intel® Core™ U processors (Skylake)
-Intel® Core™ i5-6300U processor
(3M Cache, up to 3.00 GHz)
-Intel® Core™ i3-6100U processor
(3M Cache, 2.30 GHz)
- TDP: 15 W
- BIOS: AMI 64Mbit SPI BIOS
Memory
• 2x DDR4 260-pin SO-DIMM socket, support up to 32 GB
(2133MHz, un-buffered and non-ECC type)
Graphics
• Intel® HD Graphics 520
• Triple independent display with 1x VGA, 1x DVI-D
and 1x CDS interface
Audio
• Realtek® ALC888-GR
• High Definition Audio
I/O Interface
• 1x VGA (Up to 1920 x 1080 @ 60Hz), DB-15
• 1x DVI-D (Up to 1920 x 1080 @ 60Hz)
• 1x CDS Interface, Compact PCI Connector
• 2x GbE LAN (Support WoL, Teaming, Jumbo Frame and
PXE), RJ45
- GbE1: Intel I219LM
- GbE2: Intel I210AT
• 2x PoE+ (with Optional CFM PoE Module)
- Comply with IEEE 802.3at
- Individual Port Offers Up to 25.5W
• 6x RS-232/422/485 with Auto Flow Control, DB9
- Supports 5V/12V Selectable by DIP Switch
• 4x USB 3.0, Type-A
• 1x USB 2.0, Type-A
• 16x Isolated DIO (8x DI/8x DO), 20-Pin Terminal Block
• 1x Line-out & 1x Mic-in, Phone Jack 3.5mm
• 1x Power On/Off Switch
• 1x Reset Button
• 1x AT/ATX Switch
• 1x Remote Power On/Off Connector, 2-Pin Terminal Block
• 1x External FAN Connector, 4-Pin Terminal Block
Storage
• 2x 2.5” SATA HDD/SSD Bay, Support RAID 0/1 (Gen3)
• 2x mSATA (One Shared by Mini-PCIe Socket) (Gen2)
• 1x CFast Socket (Gen3)
Expansion
• 1x CFM PoE interface
• 1x CFM IGN interface
• 2x Full-size Mini-PCIe Socket
• 1x PCI or 1x PCIex4 Socket (For P2002E only)
Support maximum dimension of add-on card(H x L):
100mm x 200mm
• 1x Universal I/O Bracket
• 1x SIM Socket
• 4x Antenna Hole
1.5 Hardware Specification
Other Function
• Support CDS Technology
• Support CFM Technology
• Support Instant Reboot Technology (0.2 sec)
• Support Power Ignition Sensing (IGN)
• Support OSD Function
(LCD On/Off, Brightness Up, Brightness Down for CDS
Display Module)
• Internal Speaker AMP 2W + 2W
• SuperCap Integrated
• Watchdog Timer:
Software Programmable Supports 1~255 sec. System Reset
Power Requirement
• Support AT/ATX Power Mode
• Power Input Voltage 9~48VDC
• One 3-pin Terminal Block Connector
• Optional Power Adapter AC/DC 12V/5A 60W or 24V/5A
120W
Physical
• Dimension (WxDxH): 254.5 x 220 x 54 mm (P2002)
254.5 x 220 x 72 mm (P2002E)
• Weight: : 2.92 kg (P2002)
3.18 kg (P2002E)
• Extruded Aluminum with Heavy Duty Metal
• Support Wall / VESA / CDS Mounting
• Fanless Design
• Jumper-less Design
Protection
• Reverse Power Input Protection
• Over Voltage Protection: 58V
• Over Current Protection: 15A
• ESD Protection: +/-15kV (air), +/-8kV (contact)
• Surge Protection: 3kW
Operating System
• Windows® 10
• Windows® 8.1
• Windows® 7
• Linux® Kernel 3.X
Environment
• Operating Temperature: -25°C to 70°C
(with extended temperature peripherals; Ambient with air
flow; According to IEC60068-2-1, IEC60068-2-2,
IEC60068-2-14)
• Storage Temperature: -40°C to 85°C
• Relative Humidity: 40°C @ 95% RH (Non-condensing)
• Shock: Operating, 50 Grms, Half-sine 11 ms Duration
(with SSD, according to IEC60068-2-27)
• Vibration: Operating, 5 Grms, 5-500 Hz, 3 Axes
(with SSD, according to IEC60068-2-64)
• EMC: CE, FCC Class A

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0
DC IN
Used to plug a DC power input with terminal block
DVI-D
Used to connect to an monitor with digital signal
interface
VGA
Used to connect to an monitor with analog signal
interface
LAN
Used to connect to local area network
Line-out
Used to connect to a external speaker
Mic-in
Used to connect to a microphone
USB 3.0
Used to connect to USB 3.0/2.0/1.1 compatible
devices
USB 2.0
Used to connect to USB 2.0/1.1 compatible devices
Digital I/O Terminal Block
The Digital I/O terminal block supports 16 isolated
DIO (8 digital input and 8 digital output)
Fan Power Terminal Block
Used to connect to an external fan
SW: Remote Power On/Off Terminal Block
Used to connect to remote power on/off switch
COM
Used to connect to RS-232/422/485 serial devices
1.3.1 Front
14
1.6 System I/O
P2002EP2002
CFast and SIM Card
CFast card and SIM card slot
HDD/SSD
2.5” SATA HDD/SSD Bay, Support RAID 0/1
Power On/Off Switch
Power-on or power-off the system
1.3.2 Rear
P2002EP2002

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0
P2002EP2002
Antenna Hole
Used to connect an antenna for optional Mini-PCIe
WiFi module
Universal I/O Bracket
Used to expand I/O for Mini-PCIe module
AT/ATX Switch
Used to select AT or ATX power mode
Reset Button
Used to reset the system
Power LED
Indicates the power status of the system
HDD LED
Indicates the status of the hard disk drive
OSD Function (For CDS Display Module)
- LCD On/Off
Press to turn-on or turn-off the backlight of display
-Increase Brightness
Press to increase brightness of the screen
- Decrease Brightness
Press to decrease brightness of the screen
1.3.3 Left
P2002EP2002
15
Antenna Hole
Used to connect an antenna for optional Mini-PCIe
WiFi module
COM
Used to connect to RS-232/422/485 serial devices
1.3.4 Right

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0 16
VESA Mounting Hole
These are mounting holes for VESA mount (75x75mm and 100x100mm)
1.3.5 Top
P2002EP2002

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0
Unit: mm
Unit: mm
17
1.7 Mechanical Dimension
P2002E
P2002

Jumpers, Switches
& Connectors
Chapter 2

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0 19
2.1 Jumpers Settings
When setting the jumpers, ensure that the jumper caps are placed on the correct pins. When
the jumper cap is placed on both pins, the jumper is short. If you remove the jumper cap, or
place the jumper cap on just one pin, the jumper is open. Refer to below for examples of the 2-
pin and 3-pin jumpers when they are short (on) and open (off).
12
Open
1 2
Short
Two-Pin Jumpers
12 3
Pins 1 and 2 are short
123
All pins are open 12 3 Pins 2 and 3 are short
Three-Pin Jumpers
2.2 Location of Jumpers, Switches and Connectors
2.2.1 Top View

P2000 Series
Convertible Embedded Computer | User’s Manual
CN-TB-QP22-44_V1.0 20
2.2.2 Bottom View