Cincoze DS-1100 Series User manual

Rugged Embedded Computer
6th Generation Intel® Core™ i3 / i5 / i7 (Skylake-S)
High Performance, Modular and Expandable Rugged Embedded Computer
DS-1100 Series
DOC No: DS-20161107002

DS-1100 Series
Rugged Embedded Computer | User’s Manual
2
Contents
Preface
Revision …………………………………………….……..……………….……….. 04
Copyright Notice …………………………………………………………………… 04
Acknowledgement …………………………………………….………................... 04
Disclaimer ………………………………………………………….……………….. 04
Declaration of Conformity ……………………………………….………………… 05
Product Warranty Statement ……………………………………….…………….. 06
Technical Support and Assistance ………………………………….……………. 07
Conventions Used in this Manual …………………………………….………….. 07
Safety Precaution …..…………………………………….…………….………….. 08
Package Contents ……………………………………………….……….………… 09
Ordering Information …………………………………………….……….………… 09
Optional Modules & Accessories …..………………………………...................... 10
Chapter 1 Product Introductions
1.1 Overview ………………………………………….…………………….. 12
1.2 Highlights ………………………………………….…………………….. 12
1.3 Product Pictures……..…………………………….…………………….. 13
1.4 Key Features …………………..………………….…………………….. 13
1.5 Hardware Specification ………………………….……..……………… 14
1.6 System I/O ……………………………………….……………………… 15
1.3.1 Front ……………………………………………………………… 15
1.3.2 Rear ………….………………………………….………………... 16
1.7 Mechanical Dimension ………………………….………..……………. 18
Chapter 2 Pin Definitions and Settings
2.1 Jumper Settings …………………………….………………………..... 21
2.2 Location of Jumpers, Switches and Connectors ………….……….... 22
2.2.1 Top View ……………………………….………………………… 22
2.2.2 Bottom View …………………………………………………….. 23
2.3 List of Jumpers, Connectors and Switches ……….…..….………..... 24
2.4 Definition of Switches .……...……………........................................ 25
2.5 Definition of Connectors …..….……..………................................... 26
Chapter 3 System Setup
3.1 Disassembling the System for Installation …………..…..…………... 36
3.2 Installing the CPU ……………………………………....…………….... 39
3.3 Installing a Mini-PCIe /mSATA Card on Top Side …....…………….... 42
3.4 Installing Antennas …………………………………..….…………….... 44
3.5 Installing a SATA Hard Drive on Top Side ………………....…….….... 46
3.6 Installing a Low Speed CMI Module ……….……………..…………... 48
3.7 Installing a High Speed CMI Module …….………………………….... 51
3.8 Installing a Mini-PCIe/mSATA Card at Bottom Side ...….…………... 55
3.9 Installing SO-DIMM Memory……………………..……..……………… 56
3.10 Installing a CFM-IGN Power Ignition Module ....……...……………... 59
3.11 Installing the Internal FAN ………..….………………………………… 60
3.12 Installing a PCI/PCIe Add-on Card …………………………….……... 62
3.13 Assembling the System ………………...…………..….…………….... 66
3.14 Installing a SATA Hard Drive at Front Side ...….………………..…... 69
3.15 Installing a SIM Card ……………………….………..….……………... 72
3.16 Installing the CMOS Battery ………………………..….…………….... 73
3.17 Fasten the Cover …………..……....……….…..….…………………... 75

DS-1100 Series
Rugged Embedded Computer | User’s Manual
3
3.18 Install an External Fan …….……..……….…..….………………..…... 75
3.19 Wall Mount Brackets ……..……....……….…..….…………….……... 78
Chapter 4 BIOS Setup
4.1 BIOS Introduction …….……….…………….…….…..….…………... 81
4.2 Main Setup ……..……….………………….…..….………………...... 82
4.2.1 Unlock Hide …….…………………………………………….... 82
4.2.2 System Date ……..…………………………………………….... 82
4.2.3 System Time ………..…………………………………………... 82
4.3 Advanced Setup ……………………………………………………….. 83
4.3.1 ACPI Settings ……..……………………………………………. 83
4.3.2 AMT Configuration ……………………………………………... 84
4.3.3 PCH-FW Configuration ………………………………..………. 85
4.3.4 F81866 Super IO Configuration …………………..…………... 86
4.3.5 Hardware Monitor …………………………………………….... 87
4.3.6 S5 RTC Wake Settings …………………………..………….... 88
4.3.7 Serial Port Console Redirection ……………..……………..... 89
4.3.8 CPU Configuration ……………………………..………….….... 89
4.3.9 SATA Configuration ..…………………………..……………..... 90
4.3.10 PCI Subsystem Settings ………....……………………..…..... 92
4.3.11 CSM Configuration ……..………………………………..…..... 94
4.3.12 USB Configuration …………………………………………….. 96
4.4 Chipset Setup …...……….………………….…..….…..……………... 97
4.4.1 System Agent (SA) Configuration …………………………….. 97
4.4.2 PCH-IO Configuration ………………………………………….. 98
4.5 Security Setup …...……….………………….…..….…..……………... 101
4.5.1 Administrator Password …….………………………………….. 101
4.5.2 User Password …….………………………………………..….. 101
4.6 Boot Setup …...……….….………………….…..….…..………..……... 102
4.6.1 Setup Prompt Timeout………………………………………….. 102
4.6.2 Bootup NumLock State ………………………………………….102
4.6.3 Quiet Boot ………………………………………………….……. 102
4.6.4 Fast Boot ……………..…………………………………………. 102
4.6.5 New Boot Option Policy …….…………………………….……. 102
4.7 Save & Exit …...……….….………………….…..….…..…………….... 103
4.7.1 Save Changes and Exit ………………..……………………...... 103
4.7.2 Discard Changes and Exit ………………………………………. 103
4.7.3 Save Changes and Reset ………………………………………. 103
4.7.4 Discard Changes and Reset ….………………………………… 103
4.7.5 Save Changes …………………………………………………… 103
4.7.6 Discard Changes ………………………………………………… 103
4.7.7 Restore Defaults ………………………….……………………… 103
4.7.8 Save as User Defaults ………………..………………………… 103
4.7.9 Restore User Defaults ..………………….……………………… 103
Chapter 5 Product Application
5.1 Digital I/O (DIO) Application……………………….…..….……………..105
5.1.1 Digital I/O Programming Guide ………………………………... 105
5.2 CMI-CD, CMI-ICD Digital I/O (DIO) Hardware Specification ……….. 110
5.2.1 CMI-CD, CMI-ICD Connector Definitions ..….………………... 111

DS-1100 Series
Rugged Embedded Computer | User’s Manual
4
Revision
Preface
Revision Description Date
1.0 New Release 2016/11/18
1.1 Add E-Mark Certified / ICD-100 Isolated COM Pin Definition 2017/3/22
Copyright Notice
© 2016 by Cincoze Co., Ltd. All rights are reserved. No parts of this manual may be copied, modified,
or reproduced in any form or by any means for commercial use without the prior written permission of
Cincoze Co., Ltd. All information and specification provided in this manual are for reference only and
remain subject to change without prior notice.
Acknowledgement
Cincoze is a registered trademark of Cincoze Co., Ltd. All registered trademarks and product names
mentioned herein are used for identification purposes only and may be trademarks and/or registered
trademarks of their respective owners.
Disclaimer
This manual is intended to be used as a practical and informative guide only and is subject to change
without notice. It does not represent a commitment on the part of Cincoze. This product might include
unintentional technical or typographical errors. Changes are periodically made to the information
herein to correct such errors, and these changes are incorporated into new editions of the publication.

DS-1100 Series
Rugged Embedded Computer | User’s Manual
5
Declaration of Conformity
FCC
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
CE
The product(s) described in this manual complies with all application European Union
(CE) directives if it has a CE marking. For computer systems to remain CE compliant,
only CE-compliant parts may be used. Maintaining CE compliance also requires proper
cable and cabling techniques.
E-Mark
The "E" mark is based on ECE regulations issued by the Economic Commission for
Europe. It is an organizational part of the UN and the members are EU countries and
many others. Therefore, the acceptance of approved components is much broader,
especially in the eastern part of Europe. It is necessary to confirm whether a particular
country has accepted (signed) the application of an ECE-regulation; as the application it
is not mandatory for the countries.

DS-1100 Series
Rugged Embedded Computer | User’s Manual
6
Product Warranty Statement
Warranty
Cincoze products are warranted by Cincoze Co., Ltd. to be free from defect in materials and
workmanship for 2 years from the date of purchase by the original purchaser.
During the warranty period, we shall, at our option, either repair or replace any product that proves to
be defective under normal operation.
Defects, malfunctions, or failures of the warranted product caused by damage resulting from natural
disasters (such as by lightening, flood, earthquake, etc.), environmental and atmospheric disturbances,
other external forces such as power line disturbances, plugging the board in under power, or incorrect
cabling, and damage caused by misuse, abuse, and unauthorized alteration or repair, and the product
in question is either software, or an expendable item (such as a fuse, battery, etc.), are not warranted.
RMA
Before sending your product in, you will need to fill in Cincoze RMA Request Form and obtain a RMA
number from us. Our staff is available at any time to provide you with the most friendly and immediate
service.
RMA Instruction
Customers must fill in Cincoze Return Merchandise Authorization (RMA) Request Form and
obtain a RMA number prior to returning a defective product to Cincoze for service.
Customers must collect all the information about the problems encountered and note anything
abnormal and describe the problems on the “Cincoze Service Form” for the RMA number apply
process.
Charges may be incurred for certain repairs. Cincoze will charge for repairs to products whose
warranty period has expired. Cincoze will also charge for repairs to products if the damage
resulted from acts of God, environmental or atmospheric disturbances, or other external forces
through misuse, abuse, or unauthorized alteration or repair. If charges will be incurred for a
repair, Cincoze lists all charges, and will wait for customer’s approval before performing the
repair.
Customers agree to insure the product or assume the risk of loss or damage during transit, to
prepay shipping charges, and to use the original shipping container or equivalent.
Customers can be send back the faulty products with or without accessories (manuals, cable,
etc.) and any components from the system. If the components were suspected as part of the
problems, please note clearly which components are included. Otherwise, Cincoze is not
responsible for the devices/parts.
Repaired items will be shipped along with a "Repair Report" detailing the findings and actions
taken.
Limitation of Liability
Cincoze’ liability arising out of the manufacture, sale, or supplying of the product and its use, whether
based on warranty, contract, negligence, product liability, or otherwise, shall not exceed the original
selling price of the product. The remedies provided herein are the customer’s sole and exclusive
remedies. In no event shall Cincoze be liable for direct, indirect, special or consequential damages
whether based on contract of any other legal theory.

DS-1100 Series
Rugged Embedded Computer | User’s Manual
7
Technical Support and Assistance
1. Visit the Cincoze website at www.cincoze.com/warranty.php where you can find the latest
information about the product.
2. Contact your distributor or our technical support team or sales representative for technical support
if you need additional assistance. Please have following information ready before you call:
Product name and serial number
Description of your peripheral attachments
Description of your software (operating system, version, application software, etc.)
A complete description of the problem
The exact wording of any error messages
Conventions Used in this Manual
This indication alerts operators to an operation that, if not strictly
observed, may result in severe injury.
WARNING
This indication alerts operators to an operation that, if not strictly
observed, may result in safety hazards to personnel or damage to
equipment.
CAUTION
This indication provides additional information to complete a task easily.
NOTE

DS-1100 Series
Rugged Embedded Computer | User’s Manual
8
Safety Precautions
Before installing and using this device, please note the following precautions:
1. Read these safety instructions carefully.
2. Keep this User’s Manual for future reference.
3. Disconnected this equipment from any AC outlet before cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and must be
easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause
damage.
7. Make sure the voltage of the power source is correct before connecting the equipment to the
power outlet.
8. Use a power cord that has been approved for using with the product and that it matches the
voltage and current marked on the product’s electrical range label. The voltage and current rating
of the cord must be greater than the voltage and current rating marked on the product.
9. Position the power cord so that people cannot step on it. Do not place anything over the power
cord.
10.All cautions and warnings on the equipment should be noted.
11.If the equipment is not used for a long time, disconnect it from the power source to avoid damage
by transient overvoltage.
12.Never pour any liquid into an opening. This may cause fire or electrical shock.
13.Never open the equipment. For safety reasons, the equipment should be opened only by qualified
service personnel.
If one of the following situations arises, get the equipment checked by service personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it work according to the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
14. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer.

DS-1100 Series
Rugged Embedded Computer | User’s Manual
9
Package Contents
Before installation, please ensure all the items listed in the following table are included in the package.
Item Description Q’ty
1 Embedded System 1
2 Utility DVD Driver 1
3 Heat Sink Pack 1
4 Screw Pack 1
5 Wall Mounting Kit 1
6 Power Terminal Block Connector 1
7 Remote Power On/Off Terminal Block Connector 2
8 Fan Terminal Block Connector 1
9 DVI-I to VGA Adaptor 1
Note: Notify your sales representative if any of the above items are missing or damaged.
Ordering Information
Model No. Product Description
DS-1100-R10 6th Generation Intel® Core™ i3/ i5/ i7 (Skylake-S) High Performance,
Modular and Expandable Rugged Embedded Computer
DS-1101-R10
6th Generation Intel® Core™ i3/ i5/ i7 (Skylake-S) High Performance,
Modular and Expandable Rugged Embedded Computer with One
PCI/PCIe Expansion Slot
DS-1102-R10
6th Generation Intel® Core™ i3/ i5/ i7 (Skylake-S) High Performance,
Modular and Expandable Rugged Embedded Computer with Two
PCI/PCIe Expansion Slots

DS-1100 Series
Rugged Embedded Computer | User’s Manual
10
Optional Modules & Accessories
Model No. Description
CFM-IGN101 CFM Module with Power Ignition Sensing Control Function, Selectable 12V/24V (43 x 36 mm)
CMI-CD100/FB20 CMI Module with 4x RS-232/422/485 Serial Ports, 8x Optical Isolated DIO (4 in/4 out), 1x DS-1100
Front Bezel
CMI-CD100/FB21 CMI Module with 4x RS-232/422/485 Serial Ports, 8x Optical Isolated DIO (4 in/4 out), 1x DS-1101
Front Bezel
CMI-CD100/FB22 CMI Module with 4x RS-232/422/485 Serial Ports, 8x Optical Isolated DIO (4 in/4 out), 1x DS-1102
Front Bezel
CMI-ICD100/FB20 CMI Module with 4x Electrical Isolated RS-232/422/485 Serial Ports, 8x Optical Isolated DIO
(4 in/4 out), 1x DS-1100 Front Bezel
CMI-ICD100/FB21 CMI Module with 4x Electrical Isolated RS-232/422/485 Serial Ports, 8x Optical Isolated DIO
(4 in/4 out), 1x DS-1101 Front Bezel
CMI-ICD100/FB22 CMI Module with 4x Electrical Isolated RS-232/422/485 Serial Ports, 8x Optical Isolated DIO
(4 in/4 out), 1x DS-1102 Front Bezel
CMI-LAN104/UB0612 CMI Module with 4x Intel GbE LAN, RJ45 Port, 1x Universal Bracket (67 x 15 mm)
CMI-PoE104/UB0612 CMI Module with 4x PoE+, Intel GbE LAN, RJ45 Port, Individual Port 25.5W, 1x Universal Bracket
(67 x 15 mm)
CMI-M12LAN104/UB0610 CMI Module with M12 Connector, 4x Intel GbE LAN, 1x Universal Bracket (67 x 15 mm)
CMI-M12PoE104/UB0610 CMI Module with M12 Connector, 4x PoE+, Intel GbE LAN, Individual Port 25.5W, 1x Universal
Bracket (67 x 15 mm)
FAN-EX100 External Fan with 4pin Terminal Block Plug, Mounting Bracket
FAN-UB100 Fan with 4pin Connector, Universal Bracket
MEC-COM-M212/UB0303 Mini-PCIe Module with 2x COM Ports, 2x Universal Brackets (65 x 16 mm)
MEC-FIR-M003/UB0301 Mini-PCIe Module with 1x 1394A Port, 2x 1394B Ports, 1x Universal Bracket (65 x 16 mm)
MEC-LAN-M002-
R1/UB0311 Mini-PCIe Module with 2x LAN Ports, 1x Universal Bracket (65 x 16 mm)
MEC-USB-M002/UB0314 Mini-PCIe Module with 2x USB 3.0 Ports, 1x Universal Bracket (65 x 16 mm)
PAH-101 Power Adapter Holder for GS120A24 (200 x 78 x 46 mm)
PAH-201 Power Adapter Holder for GS220A24 (243 x 95 x 57 mm)
GS120A24-CIN1 Adapter AC/DC 24V 5A 120W with 3pin Terminal Block Plug 5.0mm Pitch, TUBES
GS220A24-CIN1 Adapter AC/DC 24V 9.2A 220W with 3pin Terminal Block Plug 5.0mm Pitch, with TUBES
RC-E16-01 Riser Card with 1x PCIex16 Slot
RC-PI-01 Riser Card with 1x PCI Slot
RC-E16E1-01 Riser Card with 1x PCIex16, 1x PCIex1 Slots
RC-E8E8-01 Riser Card with 2x PCIex8 Slots
RC-E16PI-01 Riser Card with 1x PCIex16, 1x PCI Slots
RC-PIPI-01 Riser Card with 2x PCI Slots

Product Introductions
Chapter 1

DS-1100 Series
Rugged Embedded Computer | User’s Manual
12
1.1 Overview
1.2 Highlights
Cincoze DS-1100 Series is a high-performance fanless embedded computer powered by 6th
generation Intel® Core™ platform (Skylake-S) supporting a wide range of desktop CPUs
(socket-type, LGA1151), and accommodates two DDR4 sockets up to 32 GB which allows DS-
1100 Series to fulfill all kinds of high-end computing requirements. DS-1100 Series provides
powerful functionalities such as rich I/Os, Power over Serial, Electrical Isolated Serial Ports,
Optical Isolated Digital I/O, multiple LAN, Power over Ethernet, M12 connectors, RAID 0/1,
Power Ignition Sensing and Instant Reboot. Thanks to Cincoze’s CMI & CFM Technology, it
allows you to configure DS-1100 Series according to your specific needs with ready-to-use
modules. DS-1100 Series also supports maximum 2 PCI/PCIe expansion slots with different
combination of interfaces for expanding all kinds of application add-on cards. DS-1100 Series is
truly a rugged computing system with features of wide operating temperature (-40°C to 70°C),
wide range DC power input (from 9V to 48V), high tolerance of shock and vibration, high-
standard industrial protections and the integrated SuperCap for battery-free operation. DS-1100
Series is suitable to deploy in a harsh environment and for critical applications, and it is totally
maintenance-free.
High Performance
• Supports Intel® 6th-gen Skylake-S Series CPUs (65W/35W)
• Performance Enhanced by Intel® 14 nm Technology
• Intel® HD Graphics Supports Triple Independent Display
Resolution Up to 4K
• Intel® Q170 Chipset Brings More High-speed I/Os
Powerful Functionalities
Fully Modular and Expandable
• CMI (Combined Multiple I/O) Technology for I/O expansion
• CFM (Control Function Module) Technology for Adding
Power Ignition Sensing Function
• Mini-PCIe Modules and Dedicated I/O Brackets Are Available
• PCI/PCIe Slot with Different Combination of Interfaces
• Rich I/Os
• Power over Serial
• Electrical Isolated Serial Port
• Optical Isolated Digital I/O
• Power Ignition Sensing
• Multiple LAN
• Power over Ethernet
• RAID 0/1
• Instant Reboot
• M12 Connectors

DS-1100 Series
Rugged Embedded Computer | User’s Manual
Rear
13
1.3 Product Pictures
DS-1100
Front
• Supports Intel® 6th-Gen Core™ i3 / i5 / i7 Socket-type CPU (LGA1151)
• 2x DDR4 SO-DIMM Socket, 2,133MHz, Supports Up to 32 GB
• Triple Independent Display (DVI-I, DP, DP/HDMI)
• 2x 2.5" SATA HDD/SSD bay (Gen3), Supports RAID 0/1
• PCI/PCIe Slot with Different Combination of Interfaces (For DS-1101 & DS-1102 only)
• 2x CMI Interfaces with 6 Types of Optional Modules for I/O Expansion
• 1x CFM Interface for Adding Optional Power Ignition Sensing (IGN) Module
• Supports 3x Full-size Mini-PCIe Slot for Wireless & I/O Expansion
• Wide Operating Temperature (-40°C to 70°C)
• EN50155 / EN50121-3-2 Certified for Railway Application
• E-Mark Certified for In-vehicle Computing
1.4 Key Features
DS-1102
DS-1101

DS-1100 Series
Rugged Embedded Computer | User’s Manual
14
System
Processor
• Intel® Core™ i7-6700TE Processor (8M Cache, up to 3.40 GHz, 35W TDP)
• Intel® Core™ i5-6500TE Processor (6M Cache, up to 3.30 GHz, 35W TDP)
• Intel® Core™ i3-6100TE Processor (4M Cache, 2.70 GHz, 35W TDP)
• Intel® Pentium® Processor G4400TE (3M Cache, 2.40 GHz, 35W TDP)
• Intel® Celeron® Processor G3900TE (2M Cache, 2.30 GHz, 35W TDP)
• Intel® Core™ i7-6700 Processor (8M Cache, up to 4.00 GHz, 65W TDP)
• Intel® Core™ i5-6500 Processor (6M Cache, up to 3.60 GHz, 65W TDP)
• Intel® Core™ i3-6100 Processor (3M Cache, 3.70 GHz, 51W TDP)
• Intel® Pentium® Processor G4400 (3M Cache, 3.30 GHz, 54W TDP)
• Intel® Celeron® Processor G3900 (2M Cache, 2.80 GHz, 51W TDP)
Chipset
Intel® Q170
BIOS
AMI 16Mbit SPI BIOS
Memory
• 2x DDR4 260-pin SO-DIMM socket, support up to 32 GB
(2133MHz, un-buffered and non-ECC type)
Graphics
• Intel® HD Graphics supports triple independent display
(DVI-I, DP, DP/HDMI)
Audio
• Realtek® ALC888-GR, High Definition Audio
I/O Interface
• 1x DVI-I Connector, Resolution 1920 x 1080
• 1x DisplayPort Connector, Resolution 3840 x 2160 (DP1)
• 1x DisplayPort/HDMI Connector (DP2)
DP Resolution 3840 x 2160, HDMI Resolution 1920 x 1080
• 2x GbE LAN (Support WoL, Teaming, Jumbo Frame and PXE), RJ45
- GbE1: Intel I219LM
- GbE2: Intel I210AT
Optional CMI module available:
• 4x GbE LAN, RJ45 Port
• 4x GbE LAN, M12 Port
• PoE+ (with optional CMI module)
• 4x PoE+, RJ45 Port (IEEE 802.3at, Offers Up to 25.5W Per Port)
• 4x PoE+, M12 Port (IEEE 802.3at, Offers Up to 25.5W Per Port)
• 2x RS-232/422/485 with Auto Flow Control (Support 5V/12V), DB9
Optional CMI module available:
• 4x RS-232/422/485 (Support 5V/12V), DB9
• 4x Electrical Isolated RS-232/422/485, DB9
• 6x USB 3.0 & 2x USB 2.0 (Type-A)
• Optical Isolated DIO (with optional CMI module)
• 4x DI/4x DO, 10-Pin Terminal Block
• 1x Line-out & 1x Mic-in, Phone Jack 3.5mm
• 1x ATX Power On/Off Switch
• 1x AT/ATX Mode Switch
• 1x Clear CMOS Switch
• 1x Remote Power On/Off Connector, 2-Pin Terminal Block
• 1x Remote Reset Connector, 2-Pin Terminal Block
• 1x External FAN Connector, 4-Pin Terminal Block
Storage
• 2x 2.5” SATA HDD/SSD Bay, Support RAID 0/1 (Gen3)
• 3x mSATA (shared by Mini-PCIe socket) (Gen2)
1.5 Hardware Specification
Expansion
• 1x CFM Interface
• 2x CMI Interfaces
• 3x Full-size Mini-PCIe Sockets
• 1x SIM Socket
• PCI/PCIe Expansion:
DS-1101: 1x PCI/PCIe Expansion slot
Optional Riser Card: • 1x PCIex16 • 1x PCI
DS-1102: 2x PCI/PCIe Expansion slots
Optional Riser Card: •1x PCIex16, 1x PCIex1 • 2x PCIex8
•1x PCIex16, 1x PCIx1 • 2x PCI
Other Function
• Support CFM (Control Function Module) Technology
• Support CMI (Combined Multiple I/O) Technology
• Support Instant Reboot Technology (0.2 sec)
• SuperCap Integrated for CMOS Battery Maintain-free
• Watchdog Timer: Software Programmable Supports 1~255 sec. System Reset
• Power Ignition Sensing (IGN) Function (with optional CFM module)
12V/24V Selectable
Power Requirement
• Support AT/ATX Power Type
• Power Input Voltage 9~48VDC
• One 3-Pin Terminal Block Connector
• Power Adapter AC/DC 24V/5A 120W or 24V/9.2A 220W (Optional)
Physical
• Dimension (WxDxH) / Weight:
DS-1100: 227 x 261 x 88 mm, 4.70 kg
DS-1101: 227 x 261 x 108 mm, 5.22 kg
DS-1102: 227 x 261 x 128 mm, 5.70 kg
• Extruded Aluminum with Heavy Duty Metal
• Support Wall Mounting
• Unibody Chassis
• Fanless Design
• Jumper-less Design
Protection
• Reverse Power Input Protection
• Over Voltage Protection: 58V
• Over Current Protection: 15A
• ESD Protection: +/-15kV (air), +/-8kV (contact)
• Surge Protection: 3kW
• Operating System: Windows® 10 / 8.1 / 7
Environment
• Operating Temperature:
35W TDP Processor: -40°C to 70°C
51~65W TDP Processor: -40°C to 50°C
(With extended temperature peripherals; Ambient with air flow;
According to IEC60068-2-1, IEC60068-2-2, IEC60068-2-14)
• Storage Temperature: -40°C to 85°C
• Relative Humidity: 40°C @ 95% RH (Non-condensing)
• EMC: CE, FCC Class A
• Railway: EN50155, EN50121-3-2
• E-Mark: E13 (10R-05 14229)

DS-1100 Series
Rugged Embedded Computer | User’s Manual
1.3.1 Front
15
1.6 System I/O
ATX power on/off switch
Press to power-on or power-off the system
AT/ATX Mode Select Switch
Used to select AT or ATX power mode
Power LED
Indicates the power status of the system
Temperature LED
Indicates the temperature of the system
HDD LED
Indicates the status of the hard drive
Digital I/O LED
Indicates the working status of digital
input/ output
Ethernet LED
Indicates the status of the LAN ports
USB 3.0 Port
Used to connect USB 3.0/2.0/1.1 device
USB 2.0 Port
Used to connect USB 2.0/1.1 device
DisplayPort/HDMI
Used to connect the system with DisplayPort
or HDMI monitor
SIM card, CMOS Battery, and 2.5”
Removable HDD Bay
Used to inserts a SIM card, CMOS battery,
and 2.5” HDD
DS-1100
DS-1101

DS-1100 Series
Rugged Embedded Computer | User’s Manual
1.3.2 Rear
16
DS-1102
DC IN Terminal Block
Used to plug a DC power input with terminal
block
External Fan Terminal Block
Used to plug a external fan with terminal block
DVI-I Port
Used to connect a DVI monitor or connect
optional split cable for dual display mode
PS/2 Port
Used to connect the PS/2 device
LAN Port
Used to connect the system to a local area
network
DisplayPort
Used to connect the system with DisplayPort
Monitor
USB 3.0 Port
Used to connect USB 3.0/2.0/1.1 device
USB 2.0 Port
Used to connect USB 2.0/1.1 device
Antenna Hole
Used to install an antenna jack
COM Port
COM 1 ~ COM 2 support RS232/422/485
serial device
Mic-in
Used to connect a microphone
Line-out
Used to connect a speaker
Remote Power on/off and Remote Power
Reset Terminal Block
Used to plug a remote power on/off and
remote power reset with terminal block
Universal I/O Bracket
Used to customized I/O output

DS-1100 Series
Rugged Embedded Computer | User’s Manual
17
DS-1101
DS-1102
DS-1100

DS-1100 Series
Rugged Embedded Computer | User’s Manual
Unit: mm
18
1.7 Mechanical Dimension
DS-1100
Unit: mm
DS-1101

DS-1100 Series
Rugged Embedded Computer | User’s Manual
Unit: mm
19
DS-1102

Pin Definitions and Settings
Chapter 2