Fujitsu DESKPOWER 5000 Series User manual

DESKPOWER 5000 Series User’s Manual
Fujitsuendeavourstoensurethattheinformationinthisdocumentiscorrect,butacceptsnoliability
for any error or omission in the same. Any procedures described in this document for operating
Fujitsuproductsshouldbereadandunderstoodbytheoperatorbeforesuchproductsareused.
ToensurethatFujitsuproductsfunctionwithoutrisktosafetyandhealth,suchproceduresshould
be strictly observed by the operator. The development of Fujitsu products and services is
continuous and published information may not be up to date. Any particular issue of a product
maycontainfacilitiesnotdescribedherein.ItisimportanttocheckthecurrentpositionwithFujitsu.
SpecificationsandstatementsastoperformanceinthisdocumentareFujitsuestimatesintended
for general guidance. They may require adjustment in particular circumstances and should
therefore not be taken as formal offers or commitments.
DESKPOWER is a trademark of Fujitsu Limited. The following are registered trademarks of
MiscrosoftCorporation:MS,MS-DOS,Windows®NT,Windows®forWorkgroups,Windows®95,
Windows® 98. Celeron,Pentium II and III are the registered trade mark of Intel Corporation.
Phoenix and the Phoenix logo are registered trademarks of Phoenix Technologies, Ltd. Intel®
Pentium™andMMX™technology are trademarksof IntelCorporation. ATIGraphic Chip:RAGE
PROTURBOandRAGEXLaretheregisteredtrademarksofATITechnologies,Inc.Awardisthe
registered trademark of Award Software International Inc.
All Rights Reserved. Copyright©Fujitsu Limited, 2000
The use of screens is permitted by Microsoft Corporation in the United States.
All other products are trademarks or registered trademarks of their respective companies.
© Copyright 2000 Fujitsu Limited. All rights reserved. No part of this publication may be copied,
reproduced, or translated without the prior written consent of Fujitsu Limited. No part of this
publicationmaybestoredortransmittedinanyelectronicformwithoutthewrittenconsentofFujitsu
Limited.
Fujitsu PC (Asia) Pte Ltd
200 Pandan Loop
#05-03 Pantech 21
The Computer Centre
Singapore 128388
Tel : [phone]
Fax : [phone]
01-Intro 25/4/00, 10:36 am1

IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions carefully. Save these instructions for future reference.
2. Follow all warnings and instructions marked on the product.
3. Unplugthisproductfromthewalloutletbeforecleaning.Donotuseliquidcleanersoraerosolcleaners.
Use a damp cloth for cleaning.
4. Do not use this product near water.
5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious
damage to the product.
6. Slotsandopeningsinthecabinetandthebackorbottomareprovidedforventilation;toensurereliable
operationoftheproductandtoprotectitfromoverheating,theseopeningsmustnotbeblockedorcovered.
The openingsshouldneverbeblockedbyplacingtheproductonabed,sofa,rug,orothersimilarsurface.
This product should never be placed near or over a radiator or heat register, or in a built-in installation
unless proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking label. If you are not
sure of the type of power available, consult your dealer or local power company.
8. Thisproductis equipped with a 3-wire grounding-type plug, a plug having athird (grounding) pin.This
willonlypluginto a grounding-type power outlet. This isasafetyfeature.Ifyou are unable to insert the
plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose
of the grounding-type plug.
9. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on
the cord.
10. If an extension cord is used with this product, make sure that the total ampere rating of the equipment
plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure
that the total rating of all products plugged into the wall outlet does not exceed 15 amperes.
11. Never push objects of any kind into this product through cabinet slots as they may touch dangerous
voltage points that could result in a fire or electric shock. Never spill liquid of any kind on the product.
12. Do not attempt to service this product yourself, as opening or removing covers may expose you to
dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
13. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally when the operating instructions are followed. Adjust
only those controls that are covered by the operating instructions since improper adjustment
of other controls may result in damage and will often require extensive work by a qualified
technician to restore the product to normal condition.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct change in performance, indicating a need for service.
14. CAUTION. When replacing the battery, be sure to install it with the polarities in the correct position.
There is a danger of explosion if the battery is replaced with an incorrect type or is mistreated. Do not
recharge,disassembleordisposeofinfire.Replaceonlywiththesameorequivalenttyperecommeded
by the manufacturer. Dispose of the used battery according to the manufacturer’s instructions.
15. Use only the proper type of power supply cord set (provided in your accessories box) for this unit. It
shouldbe a detachable type: UL listed/CSA certified, BS1363,ASTA,SS145certified, rated 10A250V
minimum, VDE approved or its equivalent. Maximum length is 15 feet (4.6 meters).
01-Intro 25/4/00, 10:36 am2

Greetings
○○○○○○○
We thank you for purchasing the Fujitsu DESKPOWER 5000 personal computer.
This manual explains how to use the hardware of the DESKPOWER 5000.
Please read this manual carefully to ensure correct use of the DESKPOWER 5000.
This unit may malfunction if the power source is interrupted suddenly, for example, due to
lightning. Fujitsu recommends the use of an AC non-interruptible power supply unit.
(Based on guidelines for the prevention of sudden voltage interruptions by Japan Electronic
Industry Development Association (JEIDA).
This unit is class B information technology equipment based on the Voluntary Control Council
for Interference (VCCI) standard by Information Technology Equipment and may create
interference if used near radio or television receivers.
Use the unit in accordance with information provided in the manual.
This unit conforms to the Personal Computer Industry Standard (PC-11-1988) of the Japan
Electronic Industry Development Association (JEIDA).
This unit conforms to the harmonic guideline.
Because this product includes cargo based on the “Foreign Exchange and Foreign Trade
Control Act,” the export of this product may require permission in accordance with said act.
Fujitsu, who is a participant of the International Energy Star Program, determines
that this product conforms to the International Energy Star Program Standard.
The International Energy Star Program is an international program for
promoting energy conservation of office equipment such as computers and
strives to develop and promote products capable of efficient energy use. This program is open
to all manufacturers, and the products to be developed include computers, displays, printers,
facsimiles, and copy machines. The same standard and markings ( ) are used among
participating countries.
The energy-saving function of this product, however, may not be applicable because of
limitations with the operating system (such as Windows NT).
01-Intro 25/4/00, 10:36 am3

Conventions used in this manual
○○○○○○○
●Warning icons
Various icons and icon/word combinations are used in this manual to encourage users to use
the equipment so as to minimize personal risk and prevent property damage. The icons are
explained as follows. The user should be familiar with the icons before responding to the
corresponding instructions. Indicatesa hazardous situation that could result in fatalor serious
woundifthe correct procedure is not applied.
Indicatesahazardous situation that could result in personal injury and/or
propertydamage if the correct procedure is not applied.
The following icons are also used with the above icon/word combinations to prevent personal
injury and/or property damage.
Theicon thatindicates the corresponding instruction is a warning.
Theillustration displayed inside or beside the icon showswhat the
warningactually means.
Theicon that indicates the corresponding instruction is a banned
action.Theillustration displayed inside or beside the icon showswhat is
actuallybanned.
Theicon ●that indicates the corresponding instruction is acommand to
proceed.Theillustration displayed inside or beside the icon shows what
toproceed.
● Representing keys and use thereof
In the text of the manual, keyboard keys are represented using only necessary characters as
shown below.
Example: [Ctrl] key, [Enter] key, and [→] key
When more than one key is to be pressed simultaneously, the keys are represented using "+"
between keys as shown below:
Example: [Ctrl] + [F3] and [Shift] + [↑]
● Representing buttons
Buttons displayed on the screen are enclosed in square brackets, [and], as shown below:
Example: [OK]
● Command entries
In the text of the manual, a command is represented as shown below:
A blank (shown with [↑]) between characters indicates that the [Space] key (long bar on the
front of the keyboard) is to be pressed once. Command names are represented in lowercase
but may be entered using uppercase letters.
WARNING
CAUTION
diskcopy a: a:
↑↑
01-Intro 25/4/00, 10:36 am4

● Conventions used in the text of the manual
The symbols used in the text of the manual have meanings as explained below:
Point indicates information necessary to run hardware or software.
Help indicates information explaining how to terminate an incorrect operation
or troubleshoot.
● Screen display examples
Screen displays provided in this manual are examples and may be different from those
(including file names) actually appearing on the display screen.
● Illustrations
Illustrations in this manual are an example using (mainly) the DESKPOWER 5000 (CD-ROM
drive-equipped model) and may be different from those actually appearing on your PC screen
depending on the model type and options installed.
●Custom-made options
Descriptions in this manual are based on the standard specifications.
Note that when custom-made options are installed, memory capacity, hard disk capacity, and
other specifications differ from the standard.
● Referencing products
In this manual, products are described using abbreviations as listed below:
Windows 95 refers to Microsoft®Windows®95 operating system.
Windows 98 refers to Microsoft®Windows®98 operating system.
Windows NT refers to Microsoft®Windows NT®Workstation operating system Version 4.0.
MS-DOS refers to Microsoft(R) MS-DOS(R) operating system Version 6.2/V.
ICU refers to ISA Configuration Utility.
The terms "your PC," "the PC," "your PC main unit," and "the PC main unit" refer to the
DESKPOWER 5000
Point
???
Help
01-Intro 25/4/00, 10:36 am5

Electric shock
WARNING
To prevent electric shock,
switch off the PC and
connected peripherals and
unplug power cords from
respective outlets before
disassembling the unit and
installing a built-in option.
Electric shock
WARNING
To prevent electric
shock and/or fire, do
not remove the cover
of this unit, which
includes a high
voltage section.
Warning and caution labels
○○○○○○○
The PC bears warning and caution labels as shown below.
The warning and caution labels must not be removed or damaged.
●Rear of the PC main unit
WARNING
●Before mounting or dismounting an optional unit in/from your PC, switch
off the PC and all connected units and unplug all power cords from
respective outlets to prevent electric shock.
Electric shock
● Inside the PC main unit
01-Intro 25/4/00, 10:36 am6

Chapter 1 Installation and Connection
This chapter outlines precautions that should be noted when
installing the PC and explains how to connect various cables.
Consult this chapter before assembling the PC.
Chapter 2 Basic Operations
This chapter explains basic operations required to use the PC,
such as how to switch the power on and off and how to proceed
with storage media.
Consult this chapter.
Chapter 3 Installing Internal Options
This chapter explains how to install internal options such as hard
disk and expansion cards.
Consult this chapter as required.
Chapter 4 BIOS Setup
This chapter explains the BIOS Setup program required for
installing an internal option in your PC or setting it in the power
saving mode.
Consult this chapter as required.
Chapter 5 Troubleshooting
This chapter explains how to proceed if your PC does not operate
correctly or if an error message appears.
Consult this chapter as required.
Appendix
This appendix provides the name of each component of your PC,
information relevant to PC maintenance, the specification of the
PC main unit, and a list of precautions.
Consult this appendix.
Manual configuration
Man
1
2
3
4
5
Appendix
01-Intro 25/4/00, 10:36 am7

Contents
Con
Chapter 1 Installation and Connection ............................................ 1
1 Installation ............................................................................. 2
Installation location .................................................................................... 2
Example of installing the PC...................................................................... 2
Preventing electromagnetic interference with aTV or radio....................... 3
2 Connection ............................................................................ 4
Attaching CRT display, keyboard, mouse, and LAN cables ....................... 5
Connecting the power cord ........................................................................ 6
Upon completion of all connections ........................................................... 6
Chapter 2 Basic Operations .............................................................. 7
1 Switching on.......................................................................... 8
2 Switching off ....................................................................... 10
Turning off the power via Windows 95/98 ................................................ 10
Turning off the power via Windows NT .................................................... 11
3 Reset .................................................................................... 12
Resetting the PC via Windows 95/98....................................................... 12
Resetting the PC via Windows NT........................................................... 12
Resetting the PC via Windows 2000........................................................ 13
4 Floppy Disk.......................................................................... 14
Handling precautions ............................................................................... 14
Mounting and dismounting a floppy disk.................................................. 14
5 CD-ROM ............................................................................... 16
Handling precautions ............................................................................... 16
Mounting and dismounting a CD-ROM disk ............................................ 17
6 Hard Disk ............................................................................. 18
What is a hard disk? ................................................................................ 18
Handling precautions ............................................................................... 18
Chapter 3 Installing Internal Options ............................................. 19
1 Introduction ......................................................................... 20
Handling precautions ............................................................................... 20
Installing positions of internal options ...................................................... 21
Removing the upper cover ....................................................................... 22
Removing the front panel......................................................................... 22
02-Contents 25/4/00, 10:36 am8

2 Installing Memory Modules................................................ 23
Memory.................................................................................................... 24
Installing an additional memory ............................................................... 24
Removing the memory............................................................................. 25
3 Installing Expansion Cards................................................ 26
Expansion cards for PCI bus (Plug & Play compatible cards) ................. 27
Expansion cards for ISA bus.................................................................... 27
Expansion card installation procedure for a PC using Windows 95/98.... 28
Expansion card installation procedure for a PC using Windows NT ........ 29
Starting and terminating the ICU (For a PC using Windows NT)............. 30
Installing an expansion card .................................................................... 31
4 Installing Expansion Bay Options..................................... 34
Replacing a internal hard disk equipped as standard.............................. 36
Installing internal options to 3.5-inch expansion bays.............................. 38
Installing internal options to 5-inch expansion bays ................................ 42
Chapter 4 BIOS Setup...................................................................... 45
1 Preface ................................................................................. 46
What is BIOS setup? ............................................................................... 46
Starting BIOS setup ................................................................................. 46
Key functions ........................................................................................... 47
Exiting BIOS setup................................................................................... 48
Menus ...................................................................................................... 48
2 Main Menu ........................................................................... 49
Details on setup items ............................................................................. 49
3 Detail Menu.......................................................................... 53
Details on setup items ............................................................................. 53
4 Security Menu ..................................................................... 63
Details on setup items ............................................................................. 63
Setting a password .................................................................................. 66
Changing passwords ............................................................................... 69
Deleting passwords.................................................................................. 69
5 Power Menu ......................................................................... 70
Details on setup items ............................................................................. 70
6 Boot Menu ........................................................................... 77
Details on setup items ............................................................................. 77
7 Info Menu ............................................................................. 79
Details on setup items ............................................................................. 79
8 Exit ....................................................................................... 81
Details on setup items ............................................................................. 81
02-Contents 25/4/00, 10:36 am9

Chapter 5 Troubleshooting .............................................................. 83
1 Error Messages ................................................................... 84
Error messages displayed by the PC....................................................... 84
Correcting errors...................................................................................... 87
2 Troubleshooting .................................................................. 88
Troubleshooting information on the computer main unit and peripheral
units ................................................................................................... 88
Troubleshooting information on Windows 95/98 ...................................... 89
If an error recurs ...................................................................................... 90
Appendix
1 Name and Function of Each Component.......................... 93
Front of the PC main unit ......................................................................... 93
Rear of the PC main unit ......................................................................... 95
Inside the PC main unit............................................................................ 97
Motherboard/riser board .......................................................................... 97
2 Standard Specifications ..................................................... 99
PC main unit specifications...................................................................... 99
LAN adapter specifications ....................................................................101
Sound specifications .............................................................................. 101
Resources.............................................................................................. 101
Connector specifications........................................................................ 103
3 Cleaning Method ............................................................... 105
Cleaning the PC main unit ..................................................................... 105
Cleaning the keyboard ........................................................................... 105
Cleaning a CD-ROM.............................................................................. 105
Cleaning the mouse............................................................................... 105
Cleaning a floppy disk drive ................................................................... 107
4 Supplement ....................................................................... 107
Peripheral devices and cables ............................................................... 107
Note on using the display ...................................................................... 107
Note on using an analog liquid crystal display....................................... 107
Digital display output.............................................................................. 107
Installing a display card (Windows 95 or 98 model)............................... 109
Replacing the display............................................................................. 109
Display and power save mode ............................................................... 109
About USB (Windows 95/98/2000) ........................................................ 109
Wake up On LAN ................................................................................... 110
Power Saving Function .......................................................................... 110
LAN Cable ............................................................................................. 110
LAN Adapter .......................................................................................... 110
USB Keyboard (Windows 98 model) ..................................................... 110
CD-ROM drive ....................................................................................... 111
Intel®processor serial number............................................................... 111
Mouse with scroll function(wheel).......................................................... 111
Restartup after installing LANDDesk®Client manager 6.0
(Windows 95/98/NT model) ............................................................. 111
02-Contents 25/4/00, 10:36 am10

Chapter 1 Installation and
Connection
This chapter outlines precautions that should be noted when installing the PC
and explains how to connect various cables.
1 Installation ................................................................................................... 2
2 Connection .................................................................................................. 4
1
03-Chap1 25/4/00, 10:36 am1

2
Installation
This section provides notes on installing and using the PC.
Installation location
○○○○○○○
Do not install the PC in the following areas:
- Area exposed to moisture, dust, or smoke
- Area poorly ventilated
- Area having open flames
- Area that may expose the PC to water
- Area exposed to direct sunlight or high temperatures.
- Area having temperatures below 10 ˚C.
- Area that are unusually small or crowded
- Area having a strong magnetic field (close to a TV or speaker)
- Area exposed to strong vibration and areas that are unstable such as an inclined surface
Example of installing the PC
○○○○○○○
Install the PC as follows.
Point
Confirm that the ventilation holes at the rear or on the bottom of the PC main unit are not
blocked when installing the PC.
Keyboard
PC main unit
Mouse
CRT display
04-Chap1(2-6) 25/4/00, 10:36 am2

3
1
Preventing electromagnetic interference with a TV or radio
○○○○○○○○○
Your PC complies with the VCCI Standard restricting electromagnetic interference with a TV
or radio. However, the computer may interfere with a TV or radio depending on the installation
location.
To prevent the PC from interfering with TV or radio reception, note the following:
●Precautions to be taken by the PC user
- Do not use the PC with the cover removed.
- Use the specified cable to connect the PC with a peripheral. Do not use an unauthorized
cable.
- After installing a cable, ensure that the connector is firmly attached and the screws (if any)
are tight.
- Do not plug the PC in the same outlet as a TV or radio.
●Precautions to be taken by the TV or radio
- Do not place a TV or radio near the PC.
- Position TV or radio antennas in such a way that interference is minimized.
- Stay away the antenna line of a TV or radio near from the PC.
- Use coaxial cables as antenna feeders.
If interference with TV or radio reception continues after switching off the PC and peripherals,
check the above items again.
04-Chap1(2-6) 25/4/00, 10:36 am3

4
WARNING
● To prevent electric shock, ground the
device (if required) before providing
power to the equipment.
To prevent fire, do not connect the ground
wire to a gas pipe.
● To prevent electric shock, unplug the PC
main unit and connected equipment
before attaching and detaching a CRT
display, keyboard, mouse, LAN cables,
and power cords.
● To prevent electric shock, fire, and/or
malfunction, ensure that the display,
keyboard, and mouse are all Fujitsu brand
products.
CAUTION
● Ensure that cables are connected
correctly.
Using the PC and peripherals when
connected incorrectly may result in a
malfunction.
●To prevent a fire and/or malfunction,
connect only the specified device to the
AC service outlet (if provided).
● To prevent injury and/or malfunction, do
not touch PC board components that are
not specified.
Point
To connect a LAN cable, use a twisted pair cable, which must
be purchased separately as it is not included with your PC
package.
Connection
Connect the display, keyboard, and power cord to your PC main unit
Connect the LAN cable.
Secure one end of the twisted
pair cable (purchased
separately) to the LAN
connector at the rear of the
PC main unit.
Connect the LAN cable.
Secure the other end of the
twisted pair cable (purchased
separately) to the network
connector.
Electric shock
Electric shock
Electric shock
Failure
Fire
Injury
04-Chap1(2-6) 25/4/00, 10:36 am4

5
1
Attaching CRT display, keyboard, mouse, and LAN cables
○○○○○○○
Point
This section explains how to connect the CRT display so as to supply power from the PC main
unit. In this case, the power cord included with the CRT display is not used.
Connect the power cord to
the CRT display.
Secure one end of the power
cord (for CRT) to the inlet at
the rear of the CRT display. Connect the power cord to
the outlet.
Secure the other end of the
power cord (for CRT) to the
outlet at the rear of the PC
main unit.
Connect the keyboard.
Secure the keyboard cable
connector to the keyboard
connector (ensuring that the
colors of the keyboard
connector and keyboard label
at the rear of the PC main
unit match and that the icon
on the keyboard cable
connector housing is facing
Connect the CRT cable to the
PC main unit.
Secure the CRT cable
connector to the CRT
connector at the rear of the
PC main unit and secure the
connector screws.
Connect the mouse.
Secure the mouse cable
connector to the mouse
connector (ensuring that the
colors of mouse connector
and mouse label at the rear
of the PC main unit match
and that the arrow on the
mouse cable connector
housing is facing up).
04-Chap1(2-6) 25/4/00, 10:36 am5

6
Connecting the power cord
○○○○○○○○○
After connecting the display and other peripherals to the PC main unit, note the following when
connecting the power cord of the PC main unit.
- Do not plug or unplug the power cord with wet hands.
- Do not damage or remodel the power cord.
- Do not bend, stretch, or place heavy objects on the power cord.
- Do not use the PC if the power cord or plug is damaged
- If the electrodes of the power cord plug or the corresponding outlet is dusty, wipe with a dry
cloth.
- Connect the power cord to a household power source.
Point
Do not plug the power cord of your PC in a multiple plug box. Do not entangle the keyboard
and mouse cables.
- Unplug all power cords during an electrical storm.
- If only a two-pin outlet is available, use the adapter plug provided and connect the ground
wire.
- When unplugging a power cord, secure the plug housing.
- Ensure that the power plug is fully inserted into the outlet.
- Unplug the PC when not being used for a period of time.
Upon completion of all connections
○○○○○○○
Upon completion of all connections, fill out all user registration cards included with your
PC package.
The registration cards are used by manufacturers to obtain user information.
Attach the power plug to
the inlet on the rear of
the PC.
Connect the power plug to a
power source. Insert the other
end of the power plug into the
outlet.
04-Chap1(2-6) 25/4/00, 10:36 am6

Chapter 2 Basic Operations
This chapter explains basic operation methods of the PC such as how to turn
the power on and off and handle storage media.
1 Switching on ................................................................................................ 8
2 Switching off .............................................................................................. 10
3 Reset ......................................................................................................... 12
4 Floppy Disk ................................................................................................ 14
5 CD-ROM .................................................................................................... 16
6 Hard Disk ................................................................................................... 18
2
05-Chap2 25/4/00, 10:36 am7

8
Switchingon
This section explains how to switch on the PC.
CAUTION
●To prevent malfunction after turning on the PC, do not move equipment or
subject equipment to shock and/or vibration.
1 Press the power switch of the CRT display.
There is no display.
2 Press the power switch of the PC main unit.
The power lamps of the PC main unit and CRT
display light up green.
When the power is switched on, the Power On
Self Test (POST) used to check the devices
inside the PC is performed.
Prohibited action
Power
switch
06-Chap2(8-18) 25/4/00, 10:36 am8

9
2
Point
- Before switching on the PC, make sure that display is connected. If the PC is switched on
before the display is connected, the display adapter may not be recognized, and the screen
may not be displayed normally. In this case, connect the display, terminate the OS, switch off
the PC, and then switch on the PC again.
- If the display area is not centered on the screen, adjust the CRT display.
- The power lamp lights up orange when the PC is placed in standby status.
- If POST detects abnormal conditions, an error message is displayed. For error messages,
see Section 1, " Error Messages," in Chapter 5, "Troubleshooting."
- If the CRT display power cord is connected to the PC main unit, the CRT display is switched
on simultaneously with the PC main unit. In this case, the power switch of the CRT display
may remain in the on position, thereby eliminating the need to set the switch at each
operation.
Press the power switch of the PC main unit only when using the PC again, as described in
step 2, at which time the display is switched on automatically.
- Wait about 10 seconds before switching the PC on or off again.
- When starting the screen display or switching the display mode, the screen may become
disordered or vertical lines may appear temporarily (at the start and end screens of Windows
or when returning from the power savings mode).
This is not an error.
- The refresh rate of the screen must be set according to the CRT display to be used. For
extreme overflow or inclination, adjust the CRT display.
After turning on the power, set up the PC.
06-Chap2(8-18) 25/4/00, 10:36 am9

10
Turning off the power via Windows 95/98
○○○○○○○
1 Click [Start].
The "Start" menu appears.
Switchingoff
This section explains how to turn off the PC.
Point
- Before turning off the power, terminate all jobs and save all necessary data.
- Before turning off the power, confirm that the access indicator lamps ( see Appendix 1,
"Name and Function of Each Component") of the floppy and hard disk drives are off. If the
power is turned off while the access indicator lamps are on, data may be lost or data in the
floppy disk or hard disk may be destroyed.
- If the power cord is unplugged from the outlet or the power is disconnected due to a power
failure while the PC is on, re-connect he power cord or wait until AC power recovers. When
the power recovers, the PC is automatically turned on and started. "Press <F2> to enter
SETUP" may be displayed at this time. In this case, press the [F2] key, check the Setup
items from the menu, and restart the PC.
- If the "Power switch" of the BIOS setup is set to "Standby," pressing the power switch does
not switch off the PC. ( see Section 5, "Power-Saving Menu," in Chapter 4, "BIOS
Setup").
- Do not turn off the PC while the POST is operating. To switch off the PC while the POST is
operating, press the power switch for at least four seconds and confirm that the power lamp
goes off.
- If the power is turned off during the POST operation due to a power failure or some other
reason, the message, [Press <F1> to resume, <F2> to setup], may be displayed at
rebooting. In this case, press [F2] key, confirm the setup menu, and then reboot.
- If the power lamp is on in orange, repress the power switch for at least four seconds.
For Windows 98For Windows 95
06-Chap2(8-18) 25/4/00, 10:36 am10