Cino Fuzzyscan User manual

Getting Familiar with Your FuzzyScan
Thank you for choosing Cino FuzzyScan Bluetooth Cordless Image Scanner.
Powered by the combination of cutting-edge FuzzyScan 2.0 Imaging
Technology and Bluetooth 2.1 EDR wireless technology, it not only provides
outstanding reading performance, but also delivers the convenience and
freedom of mobility. This document provides a quick reference for installation
and operation purpose. The complete documentation is available at
www.cino.com.tw.
F700BT & L700BT Series Scanner
Link Indicator
Status Indicator
Beeper
Scan Window
Trigger
Reset Button
Battery Cavity
End Cap
F600BT & L600BT Series Scanner
1
HB2110 Smart Cradle
Center Indicator
Side Indicators
Paging/Reset Button
USB Bus Power S
HB2100 Charging Cradle
witch
Host Interface Port
DC Power Jack
Power Indicator
Reserved
USB Bus Power Switch
Reserved
DC Power Jack

Preparations before Using
Install the Battery
2
Ensure the battery contacts of the battery pack
are facing the charging contacts inside
the battery cavity.
Slide the battery pack into the battery cavity until
hearing a click sound before locking it with the
end cap. The scanner will give 4 beeps when the
battery pack is installed properly if the battery
ack still has power.p
Secure the end cap with the screw provided.
Charge the Battery
Choose an appropriate plug and slot it into the
power adapter cavity until it is locked. Then plug
the AC power plug into the AC wall socket.
Plug the DC power cord of power supply unit
into the DC Jack of cradle. The smart cradle will
issue the power on beeps and the center
indicator will give one blue blink. If you use the
charging cradle, please check the power
indicator of charging cradle turns steady blue.
Place the scanner on the cradle. The status
indicator of scanner will turn steady red if the
battery is not fully charged. When the battery is
fully charged, the status indicator of scanner will
ash green at regular interval.fl
For first use, please charge the new battery pack
or 8 hours prior to use.f
Use USB Bus Power
If USB 3.0 is available in your host device, both
battery charging and regular operation can be
supported by the USB Bus Power without using
external power supply.
If only USB 2.0 is available in your host device,
you are recommended to use power supply as
power source. Because the supplied power of
USB2.0 is not enough to support both battery
harging and regular operation simultaneously.c
If you want to use this feature, please slide the
USB bus power switch to “ON”. Then connect
the cradle and host device via USB cable.

3
Decide Your Radio Link Mode
The FuzzyScan Bluetooth image scanner provides several radio link modes
to communicate with most host devices. When the Bluetooth-enabled host
device is not available, it can work with the smart cradle in PAIR mode (one to
one connection) or PICO mode (multiple connections) to provide a
plug-and-play cordless migration of your existing non-Bluetooth-enabled IT
assets. Moreover, you are also able to use the scanner to work with
Bluetooth-enabled host devices via SPP master/slave modes and HID mode.
After losing the radio link, the scanner is capable of resuming the radio
connection automatically when it returns to the communication coverage. But
please note that this feature is not available in SPP slave mode. If you would
like to change the radio link mode, you have to scan the “Uninstall”
command to revert the scanner to uninstall state.
PAIR Mode
If the Bluetooth device is not available in your existing system, this is the
simplest plug-and-play solution. In this mode, one scanner can only work with
one smart cradle. The smart cradle not only provides the Bluetooth radio link
with the scanner, but also offers the legacy cabled interfaces to the host
device, including USB HID, USB COM, PS/2(DOS/V) Keyboard Wedge and
RS232 Serial.
PICO Mode
For the requirement of multiple connections, up to 7 scanners can be
connected to one smart cradle concurrently. If you would like to un-pair all
paired scanners and smart cradle, you can simply press and hold the
paging/reset button of the smart cradle for over 3 seconds. If you just want to
un-pair part of the paired scanners, please take those paired scanners to
scan the “Uninstall” command one by one.
HID Mode
Through the most helpful HID service, the scanner can work like a Bluetooth
keyboard. In this mode, the scanner is discoverable by the radio connection
request issued by a remote host device. For security purpose, you will be
requested to input the PIN Code to establish the Bluetooth connection in
most time.
SPP Master/Slave Mode
Through the standard SPP service, the scanner can work like a serial input
device. In SPP master mode, the scanner initiates the radio connection
request to a remote slave device. In SPP slave mode, the scanner is
discoverable by the radio connection request issued by a remote master
device.

Use FuzzyScan in PAIR Mode
Ensure the battery is fully charged. You may refer to the section of
Preparations before Using for details.
Please choose your desired interface cable, then plug it into the host
interface port of the smart cradle and connect it to the host device.
USB PS/2 RS232
Turn on the power of your host device.
Please note that the scanner has been pre-paired already, if the scanner
is shipped together with the smart cradle. You will see the link indicator of
scanner gives 1 blue blink per 2.5 seconds and the middle indicator of
smart cradle turns steady blue. If the scanner and smart cradle just give
alternating red and green blinks (“Uninstall” state), please follow steps
5-6 to establish the connection between the scanner and the smart
cradle.
Scan “PAIR mode” command. The status indicator of scanner will turn
steady red.
Uninstall
PAIR Mode
Place the scanner on the smart cradle, then you will hear one short beep
to indicate the pairing process is activated. The scanner will give
continuous short clicks and the link indicator of scanner will flash blue
quickly during the pairing process. When you hear 4 beeps in ascending
tone, the pairing process is completed. You will see the link indicator of
scanner giving 1 blue blink per 2.5 seconds and the center indicator of
the smart cradle turning steady blue.
If the scanner pairing process failed or it’s not placed on the smart cradle
within 20 seconds, you will hear 2 “Di-do Di-do” beeps to indicate pair
failure, the scanner will return to uninstall state automatically.
Scan the corresponding host interface quick set command to complete
the installation.
The default host interface of smart cradle is preset to USB HID. If you
want to set the host interface to USB COM, you have to install the USB
virtual COM software driver into your host device before using the
scanner. Please visit the CINO website to download the software driver.
4

Use FuzzyScan in PICO Mode
Ensure the battery is fully charged and choose your desired interface
cable, then plug it into the host interface port of the smart cradle and
connect it to the host device.
USB PS/2 RS232
Turn on the power of your host device.
Ensure the side indicators of the smart cradle give alternative red and
green blinks (in “Uninstall” state). If the smart cradle is paired with other
scanners, you can press and hold the paging/reset button for over 3
seconds to un-pair all paired scanners. Then the smart cradle will return
to uninstall state automatically.
Prepare the scanners you desire to pair with the smart cradle. Ensure the
status indicator of each scanner give alternative red and green blinks
(in “Uninstall” state). If the scanner is not in uninstall state, please scan
the “Uninstall” command to un-pair the scanner. Then scan the “PICO
mode” command, and the status indicator of scanner will turn steady red.
Uninstall
PICO Mode
Place the scanner on the smart cradle, then you will hear one short beep
to indicate the pairing process is activated. The scanner will give
continuous short clicks and the link indicator of scanner will flash blue
quickly during the pairing process. When you hear 4 beeps in ascending
tone, the pairing process is completed. You will see the link indicator of
scanner giving 1 blue blink per 2.5 seconds, the center indicator of the
smart cradle turning steady blue and its side indicators turning steady
green.
If the scanner pairing process failed or it’s not placed on the smart cradle
within 20 seconds, you will hear 2 “Di-do Di-do” beeps to indicate pair
failure, the scanner will return to uninstall state automatically.
Please scan the corresponding host interface quick set command to
complete the installation. Then follow the same procedures to pair other
scanners with the smart cradle.
5
For user’s convenience, the smart cradle will automatically assign the ID
numbers to each scanner. Once you completed all pairing processes,
please scan the “System Information” command to check the assigned ID
number of each scanner.

Use FuzzyScan in HID Mode
Ensure the battery is fully charged. Power on the scanner within radio
range and ensure the status indicator of scanner gives alternating red
and green blinks (in “Uninstall” state). If the scanner is not in uninstall
state, please scan the “Uninstall” command first. Then scan the “HID
Mode” command, and the link indicator of scanner will give 3 blue blinks
per 2 seconds.
Uninstall
HID Mode
Execute the Bluetooth Discovery procedure to find all available Bluetooth
device list in your remote host. You will see ‘’CINO FxxxBT-xxxx’’ is
shown in the list if the scanner is successfully discovered already.
Double click the “CINO FxxxBT-xxxx” in the discovered Bluetooth device
list. If the PIN Code or Passkey is requested for security connection,
please enter “00000000” (default setting). You will see “Keyboard on
CINO FxxxBT-xxxx”, and double click this HID service to establish the
connection between the scanner and the remote host device.
The scanner will give 4 beeps in ascending tone to indicate the radio is
connected. At the same time, the link indicator of scanner will give 1 blue
blink per 2.5 seconds to indicate the scanner is in radio-connected state.
Please note that if the scanner is not connected to the host device within
1 minute after scanning the “HID Mode” command, the scanner will go to
sleep automatically. You just need to press the trigger to wake up the
scanner to continue the installation.
1. The installation procedures vary on different remote host devices,
operating systems and the Bluetooth software drivers. Please consult
your professional IT consultant to obtain necessary support if any
problem has been encountered during the installation processes.
2. While using HID mode, beware of potential error in the data
transmission when radio link quality is poor. You are suggested to use
the scanner under the communication coverage all the time.
6

Use FuzzyScan in SPP Mode
Establish SPP Master Connection
Ensure the battery is fully charged. Please go to the folder of “Hardware”
located in Bluetooth Advanced Setting of the remote host device to check
its device MAC address. Then prepare a 12-character Code 128 barcode
of the remote host device MAC address, or follow the step 4 to input MAC
address by scanning 12 option codes.
Ensure a virtual COM port is available in your remote host for connecting
the scanner. If not, please go to the folder of “Local Services” located in
Bluetooth Advanced Setting. Click the “Add Serial Services” to add one
more Bluetooth COM port.
Power on the scanner within radio range and ensure the status indicator
of scanner gives alternating red and green blinks (in “Uninstall” state).
If the scanner is not in uninstall state, please scan the “Uninstall”
command first. Then scan the “SPP Master Mode” command, and the
status indicator of scanner will turn steady red.
Uninstall
SPP Master Mode
Scan a 12-character MAC address barcode, or scan 12 option codes and
“FIN” command to confirm your inputs. The scanner will give continuous
short clicks and the link indicator of the scanner will flash blue quickly
during the radio connecting process. If the PIN Code or Passkey is
requested for security connection, please enter “00000000” (default
setting).
The scanner will give 4 beeps in ascending tone to indicate the radio is
connected. At the same time, the link indicator of scanner will give 1 blue
blink per 2.5 seconds to indicate the scanner is in radio-connected state.
Please note that if the scanner failed to connect to the host device within
30 seconds, the link indicator will give 3 blue blinks per 2 seconds. But
the scanner is still continuing to discover the host device for another 30
seconds before go to sleep. In the interim, you still can scan “Uninstall”
command to revert the scanner to uninstall state. If the scanner goes to
sleep already, you just need to press the trigger to wake up the scanner to
continue the installation.
The installation procedures vary on different remote host devices,
operating systems and the Bluetooth software drivers. Please consult
your professional IT consultant to obtain necessary support if any
problem has been encountered during the installation processes.
7

Establish SPP Slave Connection
Ensure the battery is fully charged and a virtual COM port is available in
your remote host for connecting the scanner. If not, please go to the
folder of “Client Applications” located in Bluetooth Advanced Setting.
Click the “Add COM Port” to add one more Bluetooth COM port.
Power on the scanner within radio range and ensure the status indicator
of scanner gives alternating red and green blinks (in “Uninstall” state).
If the scanner is not in uninstall state, please scan the “Uninstall”
command first. Then scan the “SPP Slave Mode” command, and the link
indicator of scanner will give 3 blue blinks per 2 seconds.
Uninstall
SPP Slave Mode
Execute the Bluetooth Discovery procedure to find all available Bluetooth
device list in your remote host. You will see ‘’CINO FxxxBT-xxxx’’ is
shown in the list if the scanner is successfully discovered already.
Double click the “CINO FxxxBT-xxxx” on the discovered Bluetooth
devices. If the PIN Code or Passkey is requested for security connection,
please enter “00000000” (default setting). You will see “Serial Port on
CINO FxxxBT-xxxx”, and double click this SPP service to establish the
onnection between the scanner and the remote host device.c
The scanner will give 4 beeps in ascending tone to indicate the radio is
connected. At the same time, the link indicator of scanner will give 1 blue
blink per 2.5 seconds to indicate the scanner is in radio-connected state.
Please note that if the scanner is not connected to the host device within
1 minute, the scanner will go to sleep. You can press the trigger to wake
up the scanner to continue the installation.
The installation procedures vary on different remote host devices,
operating systems and the Bluetooth software drivers. Please consult
your professional IT consultant to obtain necessary support if any
problem has been encountered during the installation processes.
8

Out-of-range Scanning
When the radio is connected between the scanner and the remote host
device, the scanner will transmit each scanned data right after scanning the
barcode. However, the scanner is preset for unable to scan any barcode data
when it loses the radio connection with the remote host device.
If you enable the out-of-range scanning function, the scanner is able to
continue scanning barcode data while it is out of working range. All scanned
data will be temporarily stored into the memory buffer until radio link resumed.
Enable Out-of-range Scanning
Disable Out-of-range Scanning ◆
In case of the scanner is out of working range, you will hear 4 beeps in
descending tone to indicate the radio connection lost. The link indicator of
scanner will give 3 blue blinks per 2 seconds. Once the scanner is back to
working range, you will hear 4 beeps in ascending tone to indicate the radio
connection rebuilt and the scanner will give 1 blue blink per 2.5 seconds. At
the same time, all stored scanned data will be transmitted automatically right
after the radio link is resumed.
Presentation Scanning
The Presentation Scanning is designed for hand-free applications for user’s
convenience. If the “Presentation Scanning Auto-sense” function is enabled,
the scanner is capable of automatically switching to presentation mode when
you place it onto the SmartStand or cradle.
9
Enable Presentation Scanning Auto-sense
Disable Presentation Scanning Auto-sense ◆
Paging Function
The paging function is helpful for you to locate the paired smart cradle or
scanner. If you would like to page the paired smart cradle, you can scan
“Paging” command. If you would like to page the paired scanner, you can
press the paging/reset button of the smart cradle no longer than 3 seconds.
Paging/Reset Button
Paging

Batch Scanning (Inventory Mode)
Thanks to the specially designed Batch Scanning function, the scanner is
capable of storing the barcode data up to 20,000 EAN-13 labels. It is an ideal
cost-saving solution for inventory applications.
Once you scan the “Enter Batch Scanning” command to activate this function,
all scanned barcode data will be stored into the memory storage, and the
status indicator of scanner will give green blink at regular interval during
batch scanning. You can scan and store the barcode data till the memory
storage is full. If the storage is full, you will hear 2 long beeps and the status
indicator will give 2 red blinks to indicate out of storage. To terminate the
batch scanning, please scan the “Exit Batch Scanning” command.
Enter Batch Scanning
Exit Batch Scanning
How to Transmit Stored Data
The scanner is preset to scan the “Transmit Stored Data” command to
transmit all stored data. During the transmission process, the scanner will
give continuous short clicks and blue blinks. Then the scanner will give two
short beeps after data transmission is completed.
Transmit Stored Data
But you are still able to set the scanner to transmit the stored data by placing
the scanner onto the cradle as well.
Transmit Stored Data by
Scanning Barcode Command ◆
Transmit Stored Data by
Placing Scanner onto Cradle
Transmit Stored Data by
Scanning Barcode or Placing Scanner onto Cradle
The scanner is preset to keep all the stored data until you scan the “Clear All
Stored Data” command. But you are still able to change the setting to “Auto
Delete Stored Data after Transmission” as well.
Clear All Stored Data
Keep Stored Data
after Transmission ◆
Auto Delete Stored Data
after Transmission
10

If you scanned a wrong barcode, the “Delete Last Scanned Data’’ command
is helpful to recover mistake. By scanning the ‘’Delete Last Scanned Data’’
command, the last stored data can be deleted.
Delete Last Scanned Data
Use Quantity Feature
If you want to use the quantity feature, please scan “Enable Quantity Field
Transmission” command to enable this function.
Disable Quantity Field Transmission ◆
Enable Quantity Field Transmission
Once the quantity feature is enabled, you can enter the quantity from 1 to
9999 by scanning the quantity barcodes right after you scanned the barcode.
The quantity information will be stored into the memory storage together with
each scanned barcode data.
Quantity 0 Quantity 7
Quantity 4
Quantity 1 Quantity 8
Quantity 5
Quantity 2 Quantity 9
Quantity 6
Quantity 3
There are two ways to output the stored barcode data and quantity
information listed below:
y The preset output format is to transmit stored data as many times as the
quantity indicated.
y You can choose to outpt the stored data together with quantity information
in two fields, and a prest delimter “ ,“ will be outputted in between. To fulfill
different application requirements, both the delimiter and output sequency
can be changed as well.
11

Link Mode Quick Set
Uninstall SPP Master Mode
PICO Mode
PAIR Mode SPP Slave Mode
HID Mode
12
Host Interface Quick Set
(Work with Smart Cradle only)
RS232 Serial
Keyboard Replacement
PS/2 (DOS/V) KBW Standard Mode
PS/2 (DOS/V) KBW Turbo Mode
USB HID Standard Mode ◆
USB HID Turbo Mode
USB Com Port Emulation
Keyboard Layout Quick Set
USA ◆ Latin America
United Kingdom-UK
France Nertherlands
Canadian French
Germany Japan
Spain

System Commands
System Information
Factory Default
PowerTool Host Link
Master Default
Paging
Save Configuration
Sleep
Clone
13
Operation Mode Quick Set
Trigger Mode ◆
Presentation Mode
Option Codes
0 8
4 C
1 9
5 D
2 A
6 E
3 B
7 F
FIN (Finish) END (Exit)

Indications
Link Indicator
Status Indicator
Descriptions Link Indicator Beeper
Radio connected 1 blue blink per 2.5 sec. Off
Radio disconnected 3 blue blinks per 2 sec. Off
During connection Quick blue blinks Short clicks
Radio connection built 1 blue blink per 2.5 sec. 4 beeps in ascending tone
Radio connection lost 3 blue blinks per 2 sec. 4 beeps in descending tone
Data Transmission Quick blue blink Short clicks
Descriptions Status Indicator Beeper
Under charging (on cradle) Steady red Off
Fully charged (on cradle) 1 green blink at regular interval Off
Under batch scanning 1 green blink per 2.5 sec. Off
Pair failure Steady red 2 Di-do Di-do beeps
Out of memory 2 red blinks 2 long beeps
Battery power low 1 red blink at regular interval 1 beep at regular interval
Battery power extremely low 8 red blinks 8 beeps
Good read 1 green blink 1 good read beep
Under Configuration Steady red Off
Uninstall state Alternative red and green blinks Off
Upgrade state Steady red Short click
Time out warning Off 3 long beeps
Paged by smart cradle Off 6 page beeps
Sleep state / Battery no power Off Off
Center Indicator
Side Indicators
HB2100 Charging Cradle Indication
Descriptions Power Beeper
Power on Steady blue Off
HB2110 Smart Cradle Indications
Indicators
Descriptions
Center Side
Beeper
Power on 1 blue blink Off Power on beeps
Smart Cradle Upgrade State Off Steady red Short clicks
Uninstall state Off Alternative red-green
blinks Off
Radio Connected Steady blue Steady Green Off
PICO Mode Radio Disconnected Off Steady red Off
Radio Connected Steady blue Off Off
PAIR Mode Radio Disconnected Off Steady red Off
PICO Mode Steady blue Steady green 6 page beeps
Smart cradle paged
by scanner PAIR Mode Steady blue Off 6 page beeps
14