CipherLab 2200 User manual

2200 Omnidirectional Presentation
Scanner
Setup barcodes included.
Version 1.00

Copyright © 2017 CIPHERLAB CO., LTD.
All rights reserved
The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided
under a license agreement containing restrictions on use and disclosure and is also
protected by copyright law. Reverse engineering of the software is prohibited.
Due to continued product development this information may change without notice. The
information and intellectual property contained herein is confidential between CIPHERLAB
and the client and remains the exclusive property of CIPHERLAB CO., LTD. If finding any
problems in the documentation, please report them to us in writing. CIPHERLAB does
not warrant that this document is error-free.
No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying,
recording or otherwise without the prior written permission of CIPHERLAB CO., LTD.
For product consultancy and technical support, please contact the local sales
representative. Alternatively, visit our web site for more information.
The CipherLab logo is a registered trademark of CIPHERLAB CO., LTD.
All brand, product and service, and trademark names are the property of their registered
owners.
The editorial use of these names is for identification as well as to the benefit of the
owners, with no intention of infringement.
CIPHERLAB CO., LTD.
Website: http://www.cipherlab.com

FOR USA
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
IMPORTANT NOTICES

FOR EUROPE
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
The following test methods have been applied in order to prove presumption of
conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
- EN 60950-1: 2006+A11:2009+A1:2010+A12:2011+A2:2013
Safety of Information Technology Equipment
- EN 301 489-1 V2.1.1: 2016
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic
Compatibility (EMC) standard for radio equipment and services; Part 1: Common
technical requirements
- EN 301 489-3 V2.1.0: 2016
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic
Compatibility (EMC) standard for radio equipment and services; Part 3: Specific
conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and
40 GHz
- EN 302 208-1 V3.1.1: 2016
Radio Frequency Identification Equipment operating in the band 865 MHz to 868 MHz
with power levels up to 2 W and in the band 915 MHz to 921 MHz with power levels up to
4 W; Harmonised Standard covering the essential requirements of article 3.2 of the
Directive 2014/53/EU
SAFETY PRECAUTIONS
DO NOT expose the scanner to any flammable sources.
Under no circumstances, internal components are self-serviceable.
For AC power adaptor, a socket outlet shall be installed near the equipment and shall
be easily accessible. Make sure there is stable power supply for the scanner or its
peripherals to operate properly.
CARE & MAINTENANCE
Use a clean cloth to wipe dust off the scanning window and the body of the scanner.
DO NOT use/mix any bleach or cleaner.
If finding the scanner malfunctioning, write down the specific scenario and consult the
local sales representative.

Version Date Notes
1.00 Nov. 24, 2017 Initial Release
RELEASE NOTES

CONTENTS
IMPORTANT NOTICES.......................................................................................................... - 3 -
For USA ....................................................................................................................................... - 3 -
For Europe.................................................................................................................................. - 4 -
Safety Precautions.................................................................................................................. - 4 -
Care & Maintenance ............................................................................................................... - 4 -
RELEASE NOTES...................................................................................................................... - 5 -
INTRODUCTION.......................................................................................................................... 1
Inside the Package...................................................................................................................... 2
Product Highlights....................................................................................................................... 2
Symbologies Supported............................................................................................................ 3
QUICK START ............................................................................................................................... 5
Enter Configuration Mode......................................................................................................... 6
Exit Configuration Mode............................................................................................................ 6
Default Settings ........................................................................................................................... 7
Save User Settings as Defaults......................................................................................... 7
Restore User Defaults........................................................................................................... 7
Restore System Defaults..................................................................................................... 7
Read a Setup Barcode............................................................................................................... 8
Configure Parameters........................................................................................................... 8
List the Current Settings ...................................................................................................12
Create One-Scan Setup Barcodes.......................................................................................14
1D One-Scan Barcode ........................................................................................................14
2D One-Scan Barcode ........................................................................................................15
SPECIFICATIONS ..................................................................................................................... 17
FIRMWARE UPGRADE ............................................................................................................19
Using RS-232..............................................................................................................................19
Using USB Virtual COM............................................................................................................21
HOST SERIAL COMMANDS...................................................................................................23
Serial Commands ......................................................................................................................23
Example.........................................................................................................................................24
KEYBOARD WEDGE TABLE................................................................................................... 25
Key Type & Status.....................................................................................................................27
Key Type..................................................................................................................................27
Key Status...............................................................................................................................27
Example.........................................................................................................................................28

2200 Omnidirectional Presentation Scanner User Guide
NUMERAL SYSTEMS ................................................................................................................29
Decimal System.........................................................................................................................29
Hexadecimal System................................................................................................................30
ASCII Table..................................................................................................................................31
READING DRIVER LICENSES ............................................................................................. 33
License Parsing Setup..............................................................................................................33
File Type...................................................................................................................................33
Output Sequence Setup..........................................................................................................34
Separators and Fields..............................................................................................................40
Edit Separators......................................................................................................................41
Edit Fields................................................................................................................................42
KEYBOARD TYPE ONE-SCAN BARCODE........................................................................43
Keyboard Wedge........................................................................................................................43
Direct USB HID...........................................................................................................................48

1
Update
Equipped with a 2D barcode reader, the scanner is capable of reading 1D and 2D
barcodes. The scanner is designed for desktop use with ease of installation. For particular
deployment, the scanner can be integrated with other devices, like POS, to achieve
systematic data colletion.
This manual contains information on operating the scanner and using its features. It is
better to keep one copy of the manual at hand for quick reference or maintenance
purposes. To avoid any improper disposal or operation, please read the manual
thoroughly before use.
Thank you for choosing CipherLab products!
INTRODUCTION

2
Enter Setup
2200 Omnidirectional Presentation Scanner User Guide
INSIDE THE PACKAGE
The items included in the package may be different, depending on order. Rich choices of
output interfaces are available to enhance the total performance of the scanner. Refer to
product specifications.
Save the box and packaging material for future use in case it is need to store or ship the
scanner.
PRODUCT HIGHLIGHTS
Small-form-factor and built tough to survive drop test
Extremely low power consumption
Firmware upgradeable
Supports most popular barcode symbologies, including GS1-128 (EAN-128), GS1
DataBar (RSS), etc.
Supports a variety of 2D symbologies
Supports different scan modes, including Aiming Mode and Multi-Barcode ModeNote
Programmable feedback via LED indicator and beeper
Beeping tone and duration programmable for Good Read
Provides choices of output interfaces, including RS-232, Keyboard Wedge, and USB.
Programmable parameters include data output format, editing format, symbologies,
etc.
Note: In any scan mode other than Multi-Barcode Mode, a barcode acceptable to the
scanner can only contain data of 7 KB at most.

3
Update
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。
SYMBOLOGIES SUPPORTED
Most of the popular barcode symbologies are supported, as listed below. Each can be
individually enabled or disabled. The scanner will automatically discriminate and
recognize all the symbologies that are enabled. Refer to Chapter 3 錯誤! 找不到參照來源。
for details of each symbology.
Symbologies Supported: Enable/Disable Default
Codabar Enabled
Code 93 Enabled
MSI Disabled
Plessey Disabled
Telepen Disabled
Code 128 Code 128 Enabled
GS1-128 (EAN-128) Enabled
ISBT 128 Enabled
Code 2 of 5 Industrial 25 Enabled
Interleaved 25 Enabled
Matrix 25 Disabled
Code 3 of 9 Code 39 Enabled
Italian Pharmacode Disabled
French Pharmacode Disabled
EAN/UPC EAN-8 Enabled
EAN-8 Addon 2 Disabled
EAN-8 Addon 511109951 Disabled
EAN-13 Enabled
EAN-13 & UPC-A Addon 2 Disabled
EAN-13 & UPC-A Addon 5 Disabled
ISBN Disabled
UPC-E0 Enabled
UPC-E1 Disabled
UPC-E Addon 2 Disabled
UPC-E Addon 5 Disabled
UPC-A Enabled
Code 11 Disabled
GS1 DataBar GS1 DataBar Omnidirectional (RSS-14) Disabled

4
Enter Setup
2200 Omnidirectional Presentation Scanner User Guide
(RSS) GS1 DataBar Truncated Disabled
GS1 DataBar Limited (RSS Limited) Disabled
GS1 DataBar Expanded (RSS Expanded) Disabled
Composite
Code Composite CC-A/B Disabled
Composite CC-C Disabled
2D
Symbologies PDF417 Enabled
MicroPDF417 Disabled
Data Matrix Enabled
Maxicode Enabled
QR Code Enabled
MicroQR Enabled
Aztec Enabled
Han Xin Disabled

5
Update
The configuration of the scanner can be done by reading the setup barcodes (setup labels)
contained in this manual or via the ScanMaster software.
This section describes the procedure of configuring the scanner by reading the setup
barcodes and provides some examples for demonstration.
Note: If RS-232 or USB Virtual COM is selected for output interface, the host can directly
send serial commands to configure the scanner.
For example, run HyperTerminal.exe and type the 6-digit command located under
each setup barcode. Refer to Appendix II Host Serial Commands.
QUICK START

6
Enter Setup
2200 Omnidirectional Presentation Scanner User Guide
ENTER CONFIGURATION MODE
For the scanner to enter the configuration mode, have it read the "Enter Setup" barcode
located at the bottom of almost every even page of this manual.
The scanner will respond with six beeps and its LED indicator will become flashing red
after reading the barcode.
Enter Setup
For configuring scanner parameters, see “Read a Setup Barcode” below.
EXIT CONFIGURATION MODE
For the scanner to save settings and exit the configuration mode, have it read the
“Update” barcode located at the bottom of almost every odd page of this manual. To exit
the configuration mode without saving any changes, have the scanner read the “Abort”
barcode instead.
Just like reading the “Enter Setup” barcode, the scanner will respond with six beeps
and its LED indicator will become flashing red after reading the barcode. Wait for a
few seconds for the scanner to restart itself.
Update
Abort

7
Update
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。
DEFAULT SETTINGS
SAVE USER SETTINGS AS DEFAULTS
For the scanner to keep the customized settings as user defaults, have it read the “Save
as User Defaults” barcode. This is a normal setup barcode, and the scanner will respond
with two beeps (low-high tone).
After reading the “Update” barcode, the current settings will be saved as user
defaults.
S
ave as User
Defaults
RESTORE USER DEFAULTS
For the scanner to restore the user defaults saved earlier, have it read the “Restore User
Defaults” barcode. This is a normal setup barcode, and the scanner will respond with two
beeps (low-high tone).
After reading the “Update” barcode, all the parameters of the scanner will return to
their customized values.
Restore User
Defaults
RESTORE SYSTEM DEFAULTS
For the scanner to restore the factory defaults, have it read the “Restore System
Defaults” barcode. This is a normal setup barcode, and the scanner will respond with two
beeps (low-high tone).
After reading the “Update” barcode, all the parameters of the scanner will return to
their default values.
Restore System
Defaults
Note: The system default value (if there is) for each setting is indicated by an asterisk
“*”.

8
Enter Setup
2200 Omnidirectional Presentation Scanner User Guide
READ A SETUP BARCODE
CONFIGURE PARAMETERS
For most of the scanner parameters, only one read is required to set them to new values.
The scanner will respond with two beeps (low-high tone) when each parameter is set
successfully.
But for a number of special parameters, multiple reads are required to complete the
setting. In this case, the scanner will respond with a short beep indicating it needs to
read more setup barcodes. These special parameters may require reading one or more
setup barcodes, such as
Numeric barcodes, say, for keyboard type, inter-character delay, length qualification
Hexadecimal barcodes, say, for character strings as prefix, suffix, etc.
When “Keyboard Wedge” or “USB HID” is configured as the interface, Key Type and
Key Status will then become applicable. Decide whether or not to change key status
when “Normal Key” is selected for Key Type.
To complete the configuration of these special parameters, it requires reading the
“Validate” barcode, and then the scanner will respond with two beeps (low-high tone) to
indicate the input values are validated.

9
Update
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。
The example below shows how to save settings as “User Default” to restore user defaults
later:
Steps Action Scanner Feedback if Successful
1 Power on the scanner… The scanner will respond with a long beep
(high tone) and its LED indicator will
become solid red and go off quickly.
2 Enter the Configuration Mode…
T
he scanner will respond with six beeps
(high-low tone repeats three times), and
its LED indicator will be flashing red.
3 Read a Setup barcode…
For example,
T
he scanner will respond with two beeps
(low-high tone) if reading a normal setup
barcode.
4 Exit the Configuration Mode…
OR
Same as for Enter the Configuration Mode.
5 The scanner will automatically restart itself… Same as for Power on the scanner.
* When any configuration error occurs...
T
he scanner will respond with one long
beep (low tone).

10
Enter Setup
2200 Omnidirectional Presentation Scanner User Guide
The example below shows how to set numeric parameters:
Steps Action Scanner Feedback if Successful
1 Power on the scanner...
T
he scanner will respond with a long beep
(high tone) and its LED indicator will
become solid red and go off quickly.
2 Enter the Configuration Mode…
T
he scanner will respond with six beeps
(high-low tone repeats three times), and
its LED indicator will become flashing red.
3 Read a Setup barcode...
For example,
T
he scanner will respond with two beeps
(low-high tone) if reading a normal setup
barcode.
T
he scanner will respond with one short
beep if reading a special setup barcode
such as “Max. Length”, indicating the
setup requires reading more barcodes.
Read the “Decimal Value” barcode(s).
Refer to Appendix IV
“
Decimal
System”
T
he scanner will respond with two beeps
(low-high tone) when the input values are
validated.
4 Exit the Configuration Mode…
OR
Same as for Enter the Configuration Mode.
5 The scanner will automatically restart itself… Same as for Power on the scanner.
N
ormal setup
barcode
N
ormal setup
barcode
Special setup
barcode
Decimal barcodes

11
Update
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。
The example below shows how to set string parameters:
Steps Action Scanner Feedback if Successful
1 Power on the scanner...
T
he scanner will respond with a long beep
(high tone) and its LED indicator will
become solid red and go off quickly.
2 Enter the Configuration Mode…
T
he scanner will respond with six beeps
(high-low tone repeats three times), and
its LED indicator will become flashing red.
3 Read a Setup barcode...
For example,
T
he scanner will respond with one short
beep if reading a special setup barcode
such as “Prefix Code”, indicating the setup
requires reading more barcodes.
When “Keyboard Wedge” or “USB HID” is
configured for interface, Key Type and Key
Status will then become applicable. Decide
whether or not to change key status when
“Normal Key” is selected for Key Type.
Refer to Appendix III
Read the “Hexadecimal Value” barcodes
for the desired character string. For
example, read “2” and “B” for the scanner
to prefix the character “+”.
Refer to Appendix IV “Hexadecimal
System”
The scanner will respond with two beeps
(low-high tone) when the input values are
validated.
4 Exit the Configuration Mode…
OR
Same as for Enter the Configuration Mode.
5 The scanner will automatically restart itself… Same as for Power on the scanner.
Special setup
barcodes
Hexadecimal
barcodes

12
Enter Setup
2200 Omnidirectional Presentation Scanner User Guide
LIST THE CURRENT SETTINGS
The current settings of all scanner parameters can be sent to the host computer for user
inspection. The listing includes pages as shown below. Select the page of interest by
having the scanner read the “List Page x” barcode. The scanner will respond with two
beeps (low-high tone) and send the selected page to the host immediately.
Lists settings regarding Firmware Version,
Serial Number, Interface, Buzzer, and Other
Scanner Parameters List Page 1
Lists settings regarding Prefix, Suffix, and
Length Code Setting (1/2) List Page 2
Lists settings regarding Prefix, Suffix, and
Length Code Setting (2/2) List Page 3
Lists settings regarding Code ID List Page 4
Lists settings regarding: Readable Symbologies
(1/2) List Page 5
Lists settings regarding: Readable Symbologies
(2/2) List Page 6
Lists settings regarding Symbology Parameters
(1/3) List Page 7
Lists settings regarding Symbology Parameters
(2/3) List Page 8
Lists settings regarding Symbology Parameters
(3/3) List Page 9
Reserved
List Page 10