Cipherlab 1861e User manual

1800 Series Handheld RFID Reade

CP Series/8 Series/Universal

Version 1.00

The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided

under a license agreement containing restrictions on use and disclosure and is also

protected by copyright law. Reverse engineering of the software is prohibited.

Due to continued product development this information may change without notice. The

information and intellectual property contained herein is confidential between CIPHERLAB

and the client and remains the exclusive property of CIPHERLAB CO., LTD. If you find

any problems in the documentation, please report them to us in writing. CIPHERLAB

does not warrant that this document is error-free.

No part of this publication may be reproduced, stored in a retrieval system, or

transmitted in any form or by any means, electronic, mechanical, photocopying,

recording or otherwise without the prior written permission of CIPHERLAB CO., LTD.

For product consultancy and technical support, please contact your local sales

representative. Also, you may visit our web site for more information.

The CipherLab logo is a registered trademark of CIPHERLAB CO., LTD.

All brand, product and service, and trademark names are the property of their registered

owners.

The editorial use of these names is for identification as well as to the benefit of the

owners, with no intention of infringement.

CIPHERLAB CO., LTD.

Website: http://www.cipherlab.com

FOR USA

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance

20cm between the radiator & your body.

IMPORTANT NOTICES

FOR EUROPE

This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.

The following test methods have been applied in order to prove presumption of

conformity with the essential requirements of the R&TTE Directive 1999/5/EC:

- EN 60950-1: 2006+A11:2009

Safety of Information Technology Equipment

- EN 301 908-1 V4.2.1: 2010

Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS),

Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks;

Part 1: Harmonized EN for IMT-2000, introduction and common requirements, covering

essential requirements of article 3.2 of the R&TTE Directive

- EN 301 908-1 V5.2.1: 2011

Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS),

Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks;

Part 1: Harmonized EN for IMT-2000, introduction and common requirements, covering

essential requirements of article 3.2 of the R&TTE Directive

- EN 301 489-1 V1.8.1: 2008

Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic

Compatibility (EMC) standard for radio equipment and services; Part 1: Common

technical requirements

- EN 301 489-3 V1.4.1 2002

Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic

Compatibility (EMC) standard for radio equipment and services; Part 3: Specific

conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and

40 GHz

- EN 301 489-17 V2.1.1 2009

Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic

Compatibility (EMC) standard for radio equipment and services; Part 17: Specific

conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance

RLAN equipment

- EN 300 328 V1.7.1: 2006

Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband

Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band

and using spread spectrum modulation techniques; Harmonized EN covering essential

requirements under article 3.2 of the R&TTE Directive

- EN 302 208-1 V1.4.1: 2011

Electromagnetic compatibility and Radio spectrum Matters (ERM); Radio Frequency

Identification Equipment operating in the band 865 MHz to 868 MHz with power levels up

to 2 W; Part 1: Technical requirements and methods of measurement

- EN 302 208-2 V1.3.1: 2010

Electromagnetic compatibility and Radio spectrum Matters (ERM); Radio Frequency

Identification Equipment operating in the band 865 MHz to 868 MHz with power levels up

to 2 W; Part 2: Harmonized EN covering essential requirements of article 3.2 of the

R&TTE Directive

- EN50371 : 2002

Generic standard to demonstrate the compliance of low power electronic and electrical

apparatus with the basic restrictions related to human exposure to electromagnetic fields

(10 MHz - 300 GHz) -- General public

SAFETY PRECAUTIONS

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

The use of any battery or charging devices, which are not originally sold or

manufactured by CipherLab, will void your warranty and may cause damage to

human body or the product itself.

DO NOT disassemble, incinerate or short circuit the battery.

DO NOT expose the reader or the battery to any flammable sources.

For green-environment issue, it's important that battery should be recycled in a

proper way.

Under no circumstances, internal components are self-serviceable.

The charging uses an AC power adapter. A socket outlet shall be installed near the

equipment and shall be easily accessible. Make sure there is stable power supply for

the reader or its peripherals to operate properly.

CARE & MAINTENANCE

This reader is intended for industrial use. The reader is rated IP64, however, it may

do damage to the reader when being exposed to extreme temperatures or soaked

wet.

DO NOT use any pointed or sharp object to move any cover that is included on the

reader.

If you want to put away the reader for a period of time, download the collected data

to a host computer, and then take out the battery pack. Store the reader and battery

pack separately.

When the reader resumes its work, the battery will take a certain time to become

fully charged.

If you shall find the reader malfunctioning, write down the specific scenario and

consult your local sales representative.

Version Date Notes

1.00 Aug.13, 2012

Initial Release

RELEASE NOTES

CONTENTS

IMPORTANT NOTICES ...................................................................................................................... - 3 -

For USA .......................................................................................................................................... - 3 -

For Europe ..................................................................................................................................... - 4 -

Safety Precautions ........................................................................................................................ - 6 -

Care & Maintenance ..................................................................................................................... - 6 -

RELEASE NOTES .............................................................................................................................. - 7 -

INTRODUCTION .................................................................................................................................... 1

Getting Familiarized with RFID Reader ............................................................................................ 2

Overview ....................................................................................................................................... 2

Installing Battery to RFID Reader................................................................................................ 3

Charging the Battery for RFID Reader ........................................................................................ 4

Charging the Battery via Charger ................................................................................................ 5

Inside the Package............................................................................................................................ 6

Features............................................................................................................................................. 6

Accessories........................................................................................................................................ 6

QUICK START ....................................................................................................................................... 7

Power on RFID Reader...................................................................................................................... 7

Connecting USB Cable ...................................................................................................................... 7

Issuing Commands via USB Connection.......................................................................................... 8

Using HyperTerminal.................................................................................................................... 8

Confirming the USB Connection................................................................................................13

Default Settings...............................................................................................................................14

Save User Settings as Defaults.................................................................................................14

Restore User/Factory Defaults..................................................................................................14

Reader Switcher ..............................................................................................................................15

Combining with a Terminal .............................................................................................................16

1800 Configuration.........................................................................................................................17

UNDERSTANDING RFID READER.......................................................................................................19

1.1 Power......................................................................................................................................... 21

1.1.1 Power ON ..........................................................................................................................21

1.1.2 Power OFF.........................................................................................................................21

1.1.3 Power Saving Mode .........................................................................................................22

1.1.4 Low Battery Alarm ............................................................................................................23

1.2 Memory .....................................................................................................................................24

1.2.1 Transmit Buffer ................................................................................................................24

1.2.2 Memory Mode ..................................................................................................................26

1.3 Function Keys ...........................................................................................................................30

1.3.1 Normal Mode....................................................................................................................31

1.3.2 Bluetooth®Pairing Mode .................................................................................................34

1800 Series Handheld RFID Reader Reference Manual

1.3.3 Alternate Mode.................................................................................................................35

1.4 LED Indicators...........................................................................................................................36

1.4.1 System Status ..................................................................................................................36

1.4.2 Function Key Status......................................................................................................... 38

1.4.3 Bluetooth®Pairing Status................................................................................................38

1.5 Buzzer........................................................................................................................................ 39

1.6 Vibrator......................................................................................................................................43

1.7 RTC ............................................................................................................................................44

COMMUNICATION INTERFACE........................................................................................................... 45

2.1 USB Interface............................................................................................................................46

2.2 Bluetooth®Connection Type....................................................................................................47

2.3 Bluetooth®HID..........................................................................................................................48

2.3.1 Activate Bluetooth®HID & Select Keyboard Type..........................................................48

2.3.2 Keyboard Settings............................................................................................................51

2.3.3 Inter-Character Delay .......................................................................................................56

2.3.4 Inter-Function Delay.........................................................................................................56

2.3.5 HID Character Transmit Mode.........................................................................................56

2.4 Bluetooth®SPP Slave...............................................................................................................57

2.5 Bluetooth®SPP Master ............................................................................................................58

2.5.1 Activate Bluetooth®SPP Master Mode...........................................................................58

2.6 USB VCOM and HID via 3610 ..................................................................................................59

2.6.1 Activate USB VCOM and HID & Select Keyboard Type...................................................60

2.6.2 HID Keyboard Settings.....................................................................................................63

2.6.3 Inter-Character Delay .......................................................................................................68

2.6.4 Inter-Function Delay.........................................................................................................68

2.6.5 HID Character Transmit Mode.........................................................................................68

SET UP A WPAN CONNECTION ..........................................................................................................69

3.1 Connecting via Bluetooth®Dongle ..........................................................................................70

3.1.1 Change Interface..............................................................................................................70

3.1.2 Configure Related Settings..............................................................................................71

3.1.3 Bluetooth®HID and SPP Slave........................................................................................75

3.1.4 Bluetooth®SPP Master....................................................................................................83

3.2 Connecting via 3610................................................................................................................87

3.2.1 Connect to 3610 ..............................................................................................................87

3.2.2 USB HID via 3610 Connection ........................................................................................87

3.2.3 USB VCOM via 3610 Connection ....................................................................................89

3.2.4 configure Related Setting ................................................................................................90

3.3 Disconnection ...........................................................................................................................91

3.3.1 Break a Connection..........................................................................................................91

3.3.2 Reset a Connection..........................................................................................................91

RFID SCAN .........................................................................................................................................93

4.1 Scan Mode ................................................................................................................................94

4.2 Scan Time ................................................................................................................................. 96

4.2.1 Timeout.............................................................................................................................96

4.2.2 Delay Time ........................................................................................................................97

4.3 Filter...........................................................................................................................................98

1800 Series Handheld RFID Reader Reference Manual

4.3.1 EPC Encoding Scheme.....................................................................................................99

4.3.2 Included EPC ..................................................................................................................101

4.3.3 Excluded EPC..................................................................................................................105

4.3.4 Affected Tag of Included/Excluded EPC Filter..............................................................109

4.4 Multi-Tag..................................................................................................................................110

4.4.1 Counter ...........................................................................................................................110

4.4.2 Counter Reload ..............................................................................................................112

4.4.3 Multi-Tag Beep ...............................................................................................................113

4.5 Access Tag ..............................................................................................................................114

4.5.1 Tag Memory ....................................................................................................................114

4.5.2 Read/Write Tag ..............................................................................................................116

DEFINE OUTPUT FORMAT................................................................................................................121

5.1 Output Format.........................................................................................................................122

5.2 Format Editing for Hexadecimal and Raw Data....................................................................124

5.2.1 Data Count Section ........................................................................................................126

5.2.2 Time stamp Section .......................................................................................................129

5.2.3 UHF Data Section ...........................................................................................................135

5.3 Prefix/Suffix Code...................................................................................................................140

ALTERNATE MODE...........................................................................................................................143

SPECIFICATIONS ..............................................................................................................................147

System ...........................................................................................................................................147

Communications ...........................................................................................................................147

Reader............................................................................................................................................147

Electrical Characteristics ..............................................................................................................148

Physical Characteristics................................................................................................................148

Environmental Characteristics .....................................................................................................149

Programming Support...................................................................................................................149

Accessories....................................................................................................................................149

FIRMWARE UPGRADE......................................................................................................................151

Before Upgrading ..........................................................................................................................151

How to Upgrade Firmware ............................................................................................................152

Use USB Virtual COM ...............................................................................................................152

Use Bluetooth®Dongle ............................................................................................................153

Use 3610..................................................................................................................................154

Use <F2>+<Trigger>................................................................................................................154

How to Upgrade 3610 Firmware ..................................................................................................155

Upgrade 3610 CPU Firmware .................................................................................................155

Upgrade 3610 USB Bridge Firmware......................................................................................156

ASCII TABLE .....................................................................................................................................157

SCAN CODE......................................................................................................................................159

STATUS CODE ..................................................................................................................................161

1800 Series RFID Reader is designed to be the most flexible and reliable rugged RFID

gun with ergonomic form factor on the market. In terms of hardware specifically

designed to work as lightweight, ergonomic design, user-friendly LED display, easy

snap-on structure, storage capability and aggressive read-and-write range, 1800 Series

RFID Reader provides an efficient and complete solution for various applications upon

combine with the terminals via mobile computer mount.

Integrated with terminals’ functions via USB or Bluetooth to collect a larger data than

general reader, you may take diversification application for different user demands or

environment. For the environment, 1800 Series RFID Reader is also equipped with IP64

and 1.5m drop resistance features.

This manual serves to guide you through how to install, configure, and operate 1800

Series RFID Reader. We recommend you to keep one copy of the manual at hand for

quick reference or maintenance purposes. To avoid any improper disposal or operation,

please read the manual thoroughly before use.

Refer to the following documents to get more information about UHF RFID and EPC

standards.

EPCTM Radio-Frequency Identity Protocols Class-1 Generation-2 UHF RFID Protocol for

Communications at 860 MHz-960MHz Version1.2.0.

EPCTM Tag Data Standards Version1.6.9, September, 2011.

They are available on GS1 organization, http://www.gs1.org.

Thank you for choosing CipherLab products!

INTRODUCTION

1800 Series Handheld RFID Reader Reference Manual

GETTING FAMILIARIZED WITH RFID READER

OVERVIEW

LED Icon Meaning

1 Power

2 Bluetooth®Communication

3 RFID Tag Access

4 Data Transmission

5 Reader Indicator/Memory Low

Introduction

INSTALLING BATTERY TO RFID READER

1) This RFID Reader is powered by a removable 2500 mAh Li-ion battery. For intensive

data collection, we suggest it is better to purchase a spare battery for non-stop

operation.

2) Turn the battery latch to unlock position.

3) Remove the battery cover.

4) Insert the battery into the battery compartment directly so that the metal contacts on

the battery are met with the charging contacts inside the compartment. Make sure

that the battery is snugly fit into the compartment.

5) Shut the battery cover back to the RFID Reader until it clicks into place.

6) If the battery is charged successfully, press the <Trigger>, RFID Reader will be

powered on. If you can not power on the RFID Reader, maybe one of the issues

comes from battery.

Note: (1) Any improper handling may reduce the battery life.

(2) When the main battery charge becomes low, you need to charge the battery as

soon as possible or replace it with a charged one. While replacing the battery,

make sure the power is turned off.

1800 Series Handheld RFID Reader Reference Manual

CHARGING THE BATTERY FOR RFID READER

The battery may not be charged to full for shipment. When you first receive the package,

you will need to charge the battery to full before using the RFID Reader. For RFID

Reader, use the adapter to charger the battery. It takes approximately 4 hours to charge

the battery to full.

1) Install the battery to RFID Reader.

2) Remove the power cover.

3) Connect the power cord to the power jack.

4) Connect the other end of the power cord to a suitable power outlet.

5) The RFID Reader LED1 will be flashing red during charging. When the charging is

done, the LED1 will flash green. When charging error occurs, the LED1 will turn solid

red. For example, a bad or missing battery.

Note: Battery charging stops when the temperature drops below 0°C or exceeds 40°C. It

is recommended to charge the battery at room temperature (18°C to 25°C) for

optimal performance.

Introduction

CHARGING THE BATTERY VIA CHARGER

Instead of direct charging with adapter, you may use a charger to charge the battery.

However, the charging time may vary by working condition.

1) Connect the power supply cord to the power port located on the back of the charger.

2) Insert the battery to the end.

3) Confirm the lock bolt locks the battery certainly.

4) Connect the other end of the power cord to a suitable power outlet.

5) Once the power and battery are ready, the LED indicator lights.

6) After finishing charge, press down the lock bolt directly to pull out the battery.

Status LED Meaning

Blue, Solid Charger power ON

Red, Solid Charging battery

Green, Solid Charging done

Blue/Red Ratio 0.5s:0.5s Error

Note: Battery charging stops when the temperature drops below 0°C or exceeds 40°C. It

is recommended to charge the battery at room temperature (18°C to 25°C) for

optimal performance.

1800 Series Handheld RFID Reader Reference Manual

INSIDE THE PACKAGE

The following items are included in the package. Save the box and packaging material for

future use in case you need to store or ship device.

1800 Series Handheld RFID Reader

Rechargeable Li-ion Battery

Direct USB Cable

Power Adapter

Product CD

Quick Guide

Test Tags

FEATURES

Ergonomic design - ruggedized yet streamlined, with ergonomics handheld

Built tough to survive drop test and sealed against moisture/dust to industrial

standard IP64

CipherLab Proprietary operating system

4MB flash memory for Memory Mode operation

Provides up to 2KB SRAM for reserve buffer while getting out of range over a wireless

personal area network (WPAN)

UHF RFID Reader (ISO-18000-6C/EPC Class1 Gen2 Standard)

Ambidextrous friendly Trigger

Connectivity includes Bluetooth®and USB

Programmable feedback includes beeper and vibrator

Support user-friendly LED1~5 display with 3 colors

Support distance scan up to 100cm reading performance and 50cm writing ability.

Programming support includes System API, 8/9 and CP Series (LIB and DLL)

Accessory for single-split-type battery charger

ACCESSORIES

Rich choices of optional accessories are available for you to enhance the total

performance of the RFID Reader.

Spare Rechargeable Li-ion Battery

External Battery Charger

Direct USB Cable

Power Cable

Mobile Computer Mount

POWER ON RFID READER

Be sure the battery is full charging before you power on the RFID Reader. Press the

<Trigger> for 2 seconds to power on the RFID Reader. The reader will respond with a

long beep (high tone), and LED1 will become solid red for 1 second and go off.

Note: The LED2 will flash blue when you power on the RFID Reader successfully.

CONNECTING USB CABLE

1) RFID Reader supports a USB port for connecting to the host computer. You can issue

commands via an available USB cable.

2) Remove the USB port cover.

3) Connect the USB communication cable to USB port. (USB logo shall face down)

4) Connect the other end of USB cable to the host computer.

QUICK START

1800 Series Handheld RFID Reader Reference Manual

ISSUING COMMANDS VIA USB CONNECTION

USB connection can be used for issuing commands and upload data to host computer.

Below are the procedures to create a USB connection before using RFID Reader.

USING HYPERTERMINAL

On the host computer:

1) Go to the “Device Manager” on the host computer to confirm used COM port. For

example below, the USB Virtual COM_CDC - COM3 is used.

Note: For USB Interface type, the default value is VCOM CDC. Refer to 2.1 USB Interface

or Function Key used for selecting USB type during operation. Before beginning to

use RFID Reader, you have to install the available driver on the host computer

firstly. The USB virtual COM driver (CDC or Silicon) between RFID Reader and host

computer must be the same.

Quick Start

2) Use a test application to confirm the connection between host computer and RFID

Reader. E.g. HyperTerminal. Open the HyperTerminal on the host computer.

3) Enter a name and choose an icon for the connection. Click “OK” to continue.

4) According to Step 1 to select the proper connected COM port, e.g. COM3.

1800 Series Handheld RFID Reader Reference Manual

5) Click “OK”.

6) In the COM3 Properties window, you can click the “Restore Defaults” to use default

values for connection. Then, click “OK”.

This manual suits for next models

Table of contents

CipherLab 1861E User manual

Popular Card Reader manuals by other brands