CipherLab 1660 User manual

1660 Scanner —
Barcode Scanner
CipherLab dongle
Setup Cards
Quick Start Guide
a
a
a
a
1660/1661 Cordless
Scanner Quick Start Guide
1660 Scanner
1661 Scanner
requires two AAA Alkaline batteries.
requires own rechargeable Li-ion battery.
Remove battery cover and insert battery or batteries.
Press the key for about 2 seconds.
The scanner will respond with a long beep (high) tone, and the LED light will
become solid red and go off quickly.
Step 1:
Step 2: Power/Delete
Power/Delete Key
LED Indicator
Buzzer
Scan Window
Trigger Key
1661 only: Micro USB I/O Connector
Power on...
1661 Scanner —
Barcode Scanner
CipherLab dongle
Rechargeable Li-ion battery
Direct USB Cable
Setup Cards
Quick Start Guide
a
a
a
a
a
a
www.cipherlab.com
Open Your Box
>
Download the user manual CD contents using GoBetween, available at
.http://ccs.cipherlab.com
BT Connection —
CipherLab Dongle —
By factory default, the scanner is set to use BT HID for connecting to PC or target device.
You may change to BT SPP if necessary. BT pairing is required for establishing a connection.
You may use 3610 for a quick connection. All it takes is to scan the two barcode labels at
back of the dongle. No pairing is required. By factory default, the dongle is set to use USB
HID. You may change it to USB Virtual COM if necessary.
>>
By factory default, authentication is disabled on the scanner, meaning no PIN is required
unless a PIN code is displayed on the target device (see Random PIN).
Authentication
3610
Set Connection
Serial Number
While pairing, if you see a PIN code displayed on the target device, scan the ,
and barcodes to input the same code.
Start numeric
End
Use Random PIN
Preset PIN “0000” —
Preset PIN other than “0000” —
Scan the barcode. By factory default, it is set to use “0000”.
Scan the barcode.
Scan the , and barcodes.
Enable Authentication
Step 1: Enable Authentication
Step 2: Start numeric End
Use Preset PIN
Live Mode
>> See setup card: 3a/4a
>> See setup card: 2a/2b
If real-time data collection is not desired, you may set the scanner to work in Memory Mode.
Then, upload data when you are done with data collection.
Scan the barcode.
Any Live Mode connection will be suspended.
Scan data.
Scan the barcode. The scanner will resume Live Mode connection.
It will transmit data via preset BT interface or CipherLab dongle.
Scan the barcodes when you are done with data upload.
Step 1: Enable Memory Mode
Step 2:
Step 3: Send Data
Step 4: Clear Data & Confirm
>>>
If you’re using 1661, you may connect the USB cable for data upload, as well as for battery
charging. It takes about 4 hours to fully charge the battery.
Scan the barcode.
Scan data.
Connect the USB cable.
Scan the barcode when you are done with data collection.
Scan the barcodes when you are done with data upload.
Step 1: Enable Memory Mode
Step 2:
Step 3:
Step 4: Send Data
Step 5: Clear Data & Confirm
1661 Only
Memory Mode
>> See setup card: 1a
>> See setup card: 1a
Direct USB connection
for 1661 only

Depending on the interface you need, scan a specific barcode from the setup card.
BT HID
CipherLab dongle: USB HID
Direct USB cable: USB HID
interface
Supported Interface —
a
a
a
>>>>
Keyboard type PCAT(US) —
Keyboard type other than PCAT(US) —
By factory default, the keyboard type is set to PCAT(US). If you need a keyboard type other
than that, you may change it before use. If you are switching back to HID from a non-HID
interface, you will have to go through the three steps below to complete the keyboard type
setting.
Scan a specific barcode.
Scan the barcodes for the country code.
Scan the barcode to complete the setting.
Step 1: HID interface
Step 2: numeric
Step 3: End
Select Keyboard Type
For BT HID, you can only have the scanner connected to one computer at a time. If you
want to connect the scanner to another host, scan the barcode so that
the current connection record will be cleared. The scanner will restart itself automatically.
Reset Connection
Reset Connection
Select HID
>> See setup card: 3a
>> See setup card: 3a/3b
Direct USB connection
for 1661 only
P/N S1660AQG02012
Depending on the you need, scan a specific interface barcode from the setup card.
BT SPP, Master or Slave Mode
CipherLab dongle: USB Virtual COM
Direct USB cable: USB Virtual COM
interface
Supported Interface —
a
a
a
>>>>>
Restore System Defaults —
Save as User Defaults —
Restore User Defaults —
For the scanner to restore the factory defaults, scan the barcode.
Alternatively, you may use key combination in the following sequence:
Hold down the key.
When the scanner responds with two short beeps (high tone), press the
key for about 5 seconds. The scanner LED indicator becomes solid red for a while
and then goes off.
When the scanner responds with a long beep (high tone), release the keys.
Its LED indicator becomes solid red and goes off quickly.
The scanner will restore system defaults and restart itself automatically.
For the scanner to keep the current settings as user defaults, scan the
barcode.
For the scanner to restore the user defaults, which you have saved earlier, scan the
barcode.
Restore System Defaults
Step 1: Power/Delete
Step 2: Trigger
Step 3:
Save as User
Defaults
Restore
User Defaults
Restore Defaults
Select Virtual COM
>> See setup card: 4a
>> See setup card: 4b
As long as your scanner fits the requirements, the scanner can be used as a data collector
for a mobile phone.
Authentication
Scanner Requirements —
Supported Mobile Phones —
1660 firmware version 1.33 or later
1661 firmware version 1.00 or later
iPhone, iPad (HID)
BlackBerry 5.x (SPP)
Android 2.x (SPP)/Android 3.x (SPP/HID)
Windows Mobile, Windows Embedded Handheld, Windows CE (SPP/HID)
a
a
a
a
a
a
All you need to do is to scan a specific barcode. The scanner will
restart itself automatically.
mobile phone setup
Initial Setup
After scanning a specific barcode, it is set to use random PIN for the
following mobile phones in Live Mode:
iPhone, iPad: HID
Windows Mobile, Android 3.x: HID
While pairing, when you see a PIN code displayed on the target device, scan the ,
and barcodes to input the same code.
mobile phone setup
Start
numeric End
a
a
Use Random PIN
Preset PIN “0000” —
Preset PIN other than “0000” —
After scanning a specific barcode, it is set to use “0000” for the
following mobile phones in Live Mode:
BlackBerry, Android or Windows Mobile: SPP Slave Mode
Windows Mobile: HID
Scan the barcode.
Scan the , and barcodes.
mobile phone setup
Step 1: Enable Authentication
Step 2: Start numeric End
a
a
Use Preset PIN
Mobile Phone Support
>> See setup card: 5a
>> See setup card: 5b
Copyright ©2015 CipherLab Co., Ltd.