Circutor line-EDS-PS User manual

INSTRUCTION MANUAL
(M259B01-03-19A)
Energy manager
line-EDS-PS
line-EDS-PSScada
line-EDS-PSScada Pro

2
line-EDS-PSxxx
Instruction Manual

SAFETY PRECAUTIONS
DISCLAIMER
CIRCUTOR, SA reserves the right to make modi cations to the device or the unit speci ca-
tions set out in this instruction manual without prior notice.
CIRCUTOR, SA on its web site, supplies its customers with the latest versions of the device
speci cations and the most updated manuals.
www.circutor.com
CIRCUTOR, recommends using the original cables and accessories that are
supplied with the device.
DANGER
Warns of a risk, which could result in personal injury or material damage.
ATTENTION
Indicates that special attention should be paid to a speci c point.
Follow the warnings described in this manual with the symbols shown below.
If you must handle the unit for its installation, start-up or maintenance, the following
should be taken into consideration:
Incorrect handling or installation of the unit may result in injury to personnel as well as damage
to the unit. In particular, handling with voltages applied may result in electric shock, which may
cause death or serious injury to personnel. Defective installation or maintenance may also
lead to the risk of re.
Read the manual carefully prior to connecting the unit. Follow all installation and maintenance
instructions throughout the unit’s working life. Pay special attention to the installation stan-
dards of the National Electrical Code.
Refer to the instruction manual before using the unit
In this manual, if the instructions marked with this symbol are not respected or carried out correctly, it can
result in injury or damage to the unit and /or installations.
CIRCUTOR, SA reserves the right to modify features or the product manual without prior noti cation.
3
Instruction Manual
line-EDS-PSxxx

CONTENTS
SAFETY PRECAUTIONS ���������������������������������������������������������������������������������������������������������������������������������������3
DISCLAIMER ����������������������������������������������������������������������������������������������������������������������������������������������������������3
CONTENTS�������������������������������������������������������������������������������������������������������������������������������������������������������������4
REVISION LOG�������������������������������������������������������������������������������������������������������������������������������������������������������5
SYMBOLS���������������������������������������������������������������������������������������������������������������������������������������������������������������5
1�- VERIFICATION UPON RECEPTION����������������������������������������������������������������������������������������������������������������� 6
2�- PRODUCT DESCRIPTION�������������������������������������������������������������������������������������������������������������������������������6
3�- INSTALLATION OF THE DEVICE�������������������������������������������������������������������������������������������������������������������� 7
3�1�- PRELIMINARY RECOMMENDATIONS ����������������������������������������������������������������������������������������������������7
3�2�- INSTALLATION �����������������������������������������������������������������������������������������������������������������������������������������7
3�3�-72 x 72 mm PANEL ADAPTER������������������������������������������������������������������������������������������������������������������8
3�4�- DEVICE TERMINALS��������������������������������������������������������������������������������������������������������������������������������9
3�5�- EXPANSION WITH OTHER DEVICES������������������������������������������������������������������������������������������������������9
3�5�1�- Line-M-EXT-PS POWER ADAPTER�����������������������������������������������������������������������������������������������10
3�5�2�- INSTALLATION ������������������������������������������������������������������������������������������������������������������������������� 11
3�6�- CONNECTION DIAGRAM�����������������������������������������������������������������������������������������������������������������������13
4�- OPERATION ��������������������������������������������������������������������������������������������������������������������������������������������������14
4�1�- OPERATING PRINCIPLE������������������������������������������������������������������������������������������������������������������������14
4�2�- LED INDICATORS ����������������������������������������������������������������������������������������������������������������������������������14
4�3- DIGITAL OUTPUTS ���������������������������������������������������������������������������������������������������������������������������������16
5�- COMMUNICATIONS����������������������������������������������������������������������������������������������������������������������������������������17
5�1- RS-485 COMMUNICATIONS��������������������������������������������������������������������������������������������������������������������17
5�1�1�- CONNECTIONS ������������������������������������������������������������������������������������������������������������������������������17
5�2- Wi-Fi COMMUNICATIONS �����������������������������������������������������������������������������������������������������������������������18
5�2�1�- USAGE ENVIRONMENT AND HEALTH�����������������������������������������������������������������������������������������18
5�2�2�- Wi-Fi COMMUNICATIONS��������������������������������������������������������������������������������������������������������������18
6�- CONFIGURATION WEBSITE��������������������������������������������������������������������������������������������������������������������������19
6�1- NETWORK SETUP�����������������������������������������������������������������������������������������������������������������������������������20
6�2- TIME SETUP���������������������������������������������������������������������������������������������������������������������������������������������21
6�3- ACTIVE MODE �����������������������������������������������������������������������������������������������������������������������������������������21
6�4- SECURITY SETUP �����������������������������������������������������������������������������������������������������������������������������������22
6�5- INFORMATION �����������������������������������������������������������������������������������������������������������������������������������������22
7�- TECHNICAL FEATURES ��������������������������������������������������������������������������������������������������������������������������������23
8�- MAINTENANCE AND TECHNICAL SERVICE������������������������������������������������������������������������������������������������ 25
9�- GUARANTEE���������������������������������������������������������������������������������������������������������������������������������������������������25
10�- CE CERTIFICATE������������������������������������������������������������������������������������������������������������������������������������������26
4
line-EDS-PSxxx
Instruction Manual

REVISION LOG
Table 1: Revision log�
Date Revision Description
05/20 M259B01-03-19A First Version
Note: The images on the devices are for illustrative use only and may differ from the original
device.
SYMBOLS
Table 2: Symbols�
Symbol Description
In accordance with the relevant European directive.
In accordance with the CMiM directive.
Device covered by European Directive 2012/19/EC. At the end of its useful life, do not
leave the device in a household refuse bin. Follow local regulations on electronic equip-
ment recycling.
Direct current.
~Alternating current.
5
Instruction Manual
line-EDS-PSxxx

1�- VERIFICATION UPON RECEPTION
Upon reception of the device check the following points:
a) The device meets the specications described in your order.
b) The device has not suffered any damage during transport.
c) Perform an external visual inspection of the device prior to switching it on.
d) Check that it has been delivered with the following:
- An installation guide
If any problem is noticed upon reception, immediately contact the transport
company and/or CIRCUTOR’s after-sales service�
2�- PRODUCT DESCRIPTION
line-EDS-PSxxx is a device that works as connector between eld devices with Modbus RTU
or Modbus TCP communications and the PowerStudio energy management software.
Circutor has 3 models:
line-EDS-PS, with embedded PowerStudio.
line-EDS-PSScada, with embedded PowerStudio SCADA.
line-EDS-PSScada Pro, with embedded PowerStudio SCADA DELUXE.
The device features:
- 5 indication LEDs
- 2 digital outputs.
- RS-485 and Ethernet communications.
- Wi-Fi connection.
The line-EDS-PSxxx features a Web server to set up the device and display the variables of all
the modules or devices connected to it
6
line-EDS-PSxxx
Instruction Manual

3�- INSTALLATION OF THE DEVICE
3.1.- PRELIMINARY RECOMMENDATIONS
In order to use the device safely, personnel operating it must follow the safety
measures that comply with the standards of the country where it is to be installed;
operators must wear the required personal protective equipment (rubber gloves,
approved facial protection and ame-resistant clothing) to prevent injuries from
electric shock or arcs caused by exposure to current-carrying conductors, and
they must heed the various warnings indicated in this instruction manual.
The line-EDS-PSxxx device must be installed by authorised, qualied personnel.
The power supply plug must be disconnected before handling, altering the connections or re-
placing the device. It is dangerous to handle the device while it is powered.
Cables must always be kept in perfect condition to avoid accidents or injury to personnel or
installations.
The manufacturer of the device is not responsible for any damage resulting from failure by the
user or installer to heed the warnings and/or recommendations set out in this manual, nor for
damage resulting from the use of non-original products or accessories or those made by other
manufacturers.
Do not use the device to perform any operation if you detect any anomaly or malfunction.
Before carrying out maintenance, repair or handling of any of the device’s con-
nections, the device must be disconnected from all power sources, both from the
device’s own power supply and the measurement’s.
Contact the after-sales service if you detect that the device is not working prop-
erly.
3.2.- INSTALLATION
The device must be installed on an electric panel or enclosure, at tached to a DIN rail (IEC
60715).
When the device is on, its terminals, opening covers or removing elements may
expose the user to parts that are hazardous to touch. Do not use the device until
it is fully installed.
The device must be connected to a power supply circuit protected by gl type (IEC 269) or M
type fuses, between 0.5 and 2A. It must be tted with a circuit-breaker or equivalent device to
disconnect the device from the mains supply.
The power supply circuit must be connected with a 1mm² minimum cross-section cable.
7
Instruction Manual
line-EDS-PSxxx

3.3.-72 x 72 mm PANEL ADAPTER
Note: The 72 x 72 mm panel adapter is a separately sold accessory.
CIRCUTOR has a panel adapter for the line-EDS-PSxxx devices for their installation in 72 x
72 mm panels.
Figure 1 illustrates how the panel adapter connects to a line-EDS-PSxxx.
Before installing the adapter, the device must be disconnected from all power
and measurement supplies.
Figure 1: Installation of the panel adapter�
Table 3: Technical characteristics of the Panel Adapter�
Technical Specications
Protection degree IP40
Casing Self-extinguishing V0 plastic
68 mm
68 mm
Figure 2: Cut in the panel�
8
line-EDS-PSxxx
Instruction Manual

3.4.- DEVICE TERMINALS
A1
A2
24
22
23
21
20
19
23
21
20
19
24
22
Ethernet
Figure 3: Device terminals: Upper - Lower�
Table 4: List of terminals�
Device terminals
A1: Power supply 21: 1, Digital output 1
A2: Power supply 20: 2, Digital output 2
24: A+, RS-485 19: C, Common of digital outputs
23: S, GND for RS-485 Ethernet, Ethernet connection
22: B-, RS-485
3.5.- EXPANSION WITH OTHER DEVICES
The line-EDS-PSxxx devices can be expanded with other devices in the line range, the line-
CVM and line-M expansion modules.
The line-EDS-PSxxx and line-CVM devices enable up to 2 expansion modules to be directly
connected to their right-hand side(1).
line-EDS line-M line-M line-M line-M
line-CVM
Figure 4: line-EDS-PSxxx and line CVM expansion module connection�
(1) Expansion module types: line-M-4IO-R, line-M-4IO-T, line-M-4IO-RV and line-M-4IO-A�
In installations with line-EDS-PSxxx devices, a total of up to seven devices may be connected
to their right-hand side.
9
Instruction Manual
line-EDS-PSxxx

line-EDS line-M line-M line-CVM line-M line-M line-CVM line-CVM
Figure 5: Typical installation of a line-EDS-PSxxx with 7 devices�
Note: An installation may only be tted with one line-EDS-PSxxx device.
Note: In installations without line-EDS-PSxxx devices, only one line-CVM device may ne in-
stalled.
Note: All line-EDS-PSxxx and line-CVM devices must be connected to the auxiliary power
supply.
3�5�1�- Line-M-EXT-PS POWER ADAPTER
Line-M-EXT-PS is a power adapter belonging to the line family of devices. The module con-
nects to the left-hand side of the devices to be fed. It can supply up to 10 VA, allowing it to power
a limited number of devices.
The maximum set it can supply is: 1 line-EDS-PSxxx + 1 line-CVM + 1 line-M (Figure 6).
line-EDS line-M
line-M-EXT-PS line-CVM
Figure 6: Maximum set a line-M-EXT-PS can supply�
Multiple line-M-EXT-PS devices can be connected to supply sets with power above 10VA. Each
line-M-EXT-PS will power the devices connected to its right-hand side (Figure 7).
line-EDS line-M line-M line-CVM line-M line-M line-CVM line-CVM
line-M-EXT-PS line-M-EXT-PS line-M-EXT-PS
Figure 7: Multiple line-M-EXT-PS connection�
Note: None of the line-EDS-PSxxx or line-CVM devices should be connected to the auxiliary
power supply.
10
line-EDS-PSxxx
Instruction Manual

3�5�2�- INSTALLATION
Before installing a new device, it must be disconnected from all power supplies.
The correct steps to connect the devices are:
1�- Using a at head screwdriver, remove the expansion connector’s protective covers located
on the side of the devices, (Figure 8).
Figure 8: Installation step 1�
2�- Insert the expansion connector and fastening clips into one of the devices (Figure 9).
Figure 9: Installation step 2�
3�- Connect both devices and fasten them by pushing the front clips down (Figure 10).
11
Instruction Manual
line-EDS-PSxxx

Figure 10: Installation step 3�
For correct installation of all devices, please refer to the instruction manual for
the different models:
M237B01-01-xxx: Instruction Manual for line-CVM devices.
M239B01-03-xxx: Instruction Manual for line-M expansion modules.
12
line-EDS-PSxxx
Instruction Manual

3.6.- CONNECTION DIAGRAM
PC
Ethernet
ROUTER
INTERNET
PC
RS-485
Ethernet
Wi-Fi
Wi-Fi
SERVIDOR / SERVER
With a browser
compatible with HTML5
With a browser
compatible with HTML5
Con navegador Web
compatible con HTML5
Con navegador Web
compatible con HTML5
LAN
WLAN
SLAVES
line-EDS
A
B
S
Figure 11: line-EDS-PS, line-EDS-PSScada and line-EDS-PSScada Pro connection diagram�
13
Instruction Manual
line-EDS-PSxxx

4�- OPERATION
4.1.- OPERATING PRINCIPLE
The line-EDS-PSxxx is a device that works as connector between eld devices with Modbus
RTU or Modbus TCP communications and the PowerStudio energy management software.
The line-EDS-PSxxx models connect to eld devices with Modbus via RS-485, Wi-Fi or via a
Modbus TCP Ethernet connection, and they send data to the PowerStudio energy management
software.
Three device models are available, depending on the management software:
line-EDS-PSe, for the embedded PowerStudio software.
line-EDS-PSSe, for the PowerStudio SCADA software.
line-EDS-PSSDe, pfor the PowerStudio SCADA DELUXE software.
4.2.- LED INDICATORS
The devices have 5 indicating LEDs:
LAN
WLAN
SLAVES
line-EDS
WLAN
LAN
CPU
SLAVES
ALARMA
ALARM
Figure 12: LED indicators�
CPU, Device status:
Table 5: CPU LED�
LED Description
CPU Flashing (white color)
Device powered
14
line-EDS-PSxxx
Instruction Manual

LAN, Ethernet connection
Table 6: LAN LED�
LED Description
LAN
On (green color)
Connection to a local network
Flashing (green color)
Activity in the network
WLAN, Wi-Fi connection:
Table 7: WLAN LED�
LED Description
WLAN
On (blue color)
Connection to a Wi-Fi network
Flashing (blue color)
Activity in the Wi-Fi network
ALARM:
Table 8: ALARM LED�
LED Description
CPU On (red color)
Alarm activated
SLAVES, Connection with slave device:
Table 9: SLAVES LED�
LED Description
SLAVES On (red color)
The slave device doesn’t communicate
15
Instruction Manual
line-EDS-PSxxx

5�- COMMUNICATIONS
5.1- RS-485 COMMUNICATIONS
line-EDS-PSxxx devices have an RS-485 communications port.
5�1�1�- CONNECTIONS
The RS-485 cable must be wired using twisted pair cable with mesh shield (minimum 3 wires),
with a maximum distance of 1200 meters between the line-EDS-PSxxx and the slave devices.
In this bus we can connect a maximum of 32 slave devices.
RS-485
A(+)
B(-)
S
A
B
S
LAN
WLAN
SLAVES
line-EDS
A(+)
B(-)
S
A
B
S
A(+)
B(-)
S
A
B
S
line-EDS CVM-E3-MINI CVM-E3-MINI
Ethernet
SERVIDOR / SERVER
Figure 14: RS-485 connection diagram�
17
Instruction Manual
line-EDS-PSxxx

5.2- Wi-Fi COMMUNICATIONS
5�2�1�- USAGE ENVIRONMENT AND HEALTH
Wireless communications emit radio frequency electromagnetic energy, like other radio devic-
es.
Because wireless communications operate under the guidelines found in radio frequency stand-
ards and recommendations, they are safe for users to use.
In some settings and situations the use of wireless communications may be restricted by the
building’s owner of representatives of the organisation.
These may include:
Use of wireless connections on board aircraft, in hospitals or near service stations,
blasting areas, medical implants or electronic medical devices implanted in the human
body (pacemakers, etc.).
In any other setting where the risk of interference with other devices or services is a
hazard.
If you are not sure of the applicable usage policy for wireless devices in a specic organisation
(airport, hospital, etc.) we recommend requesting permission to use wireless communications.
5�2�2�- Wi-Fi COMMUNICATIONS
Wi-Fi is one of the most widely-used wireless technologies today, used to connect electronic
devices and exchange information between them without a physical connection.
The line-EDS-PSxxx has Wi-Fi communications over the 2.4 GHz band, in accordance with
the IEEE 802.11 ac / a / b / g / n standards.
Table 10: Security features of Wi-Fi communications�
Security features of Wi-Fi communications
Security protocol WPA2
18
line-EDS-PSxxx
Instruction Manual

6�- CONFIGURATION WEBSITE
The internal conguration website of the line-EDS-PSxxx models can be found at:
http://xxx�xxx�xxx/html/setup�html
http://name_dhcp/html/setup�html
http://100�0�0�1/html/setup�html
Where: xxx�xxx�xxx is the IP address assigned by the user.
name_dhcp is the name assigned and authenticated by the name server of the local
area network (LAN).
Note: The device leaves the factory with DHCP activated.
Note: To nd the device in a local network, a crossover cable has to be used to access the
device’s local IP: 100.0.0.1 with a subnet mask 255.255.255.0
If a username and login password have been set up, when trying to access via the web, the
website requests these login parameters on the following pop-up screen, Figure 15.
Figure 15: Username and password�
Figure 16 shows the conguration website.
19
Instruction Manual
line-EDS-PSxxx

Figure 16: Conguration website: line-EDS-PSxxx�
6.1- NETWORK SETUP
In this section, the Ethernet communications of the line-EDS-PSxxx are congured.
Figure 17: Conguration website: Network setup.
Host name: Identifying name within the local network.
DHCP: If DHCP is enabled (DHCP On), the IP address is dynamically assigned by a central
server and no further parameters need to be congured.
If this option is disabled, the IP address is xed and the following parameters need to be
congured:
DHCP Client ID: Device ID.
Address: IP address.
Netmask: IP subnet mask.
20
line-EDS-PSxxx
Instruction Manual
Other manuals for line-EDS-PS
1
This manual suits for next models
2
Table of contents
Other Circutor Control Unit manuals
Popular Control Unit manuals by other brands

Econ
Econ 68 Series Installation & operation manual

Kontron
Kontron SMARC-sAMX7 user guide

Siemens
Siemens SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF... manual

axing
axing SKM 40-00M Operation instructions

Rheavendors Group
Rheavendors Group rhMM1.v+ Installation and maintenance manual

Waters
Waters Bus SAT/IN installation guide