Cisco Aironet AIR-ANT2513P4M-N User manual

147
Cisco Systems, Inc. www.cisco.com
Cisco Aironet Four-Port Dual-Band
Polarization-Diverse Antenna
(AIR-ANT2513P4M-N)
This document describes the AIR-ANT2513P4M-N antenna and provides electrical specifications and mounting instructions.
The antenna is a four-port polarization-diverse patch array that operates over the 2.4-GHz and 5-GHz Wi-Fi bands. It ships with
an articulating mount for use on flat surfaces and masts and is adjustable in both the horizontal and vertical planes. The radome
is paintable using commonly available non-conductive spray paints, such as Krylon or Rust-Oleum. The antenna is designed for
use in indoor and outdoor environments with Cisco Aironet 3702P and 1570 series access points.
The following information is provided in this document:
Technical Specifications,
System Requirements
Safety Instructions
Installation Notes
Choosing a Mounting Location
Installing the Antenna
Painting the Antenna
Obtaining Documentation and Submitting a Service Request

148
Cisco Aironet Four-Port Dual-Band Polarization-Diverse Antenna (AIR-ANT2513P4M-N)
Technical Specifications
Figure 1 ANT2513P4M-N front high view
2.4 GHz Antenna Radiation Patterns
Antenna Type Dual-Band Polarization Diverse Patch Array
Operating Frequency Ranges 2.4-2.5 GHz 5.15-5.925 GHz
Nominal Input Impedance 50 Ohms 50 Ohms
VSWR 1.6:1 1.5:1 (above 5.7 GHz to 5.9 GHz)
2:1 (from 5.15 GHz to 5.7 GHz)
Peak Gain 13 dBi 13 dBi
Polarization (Ports A & C) Vertical Vertical
Polarization (Ports B & D) Horizontal Horizontal
Nominal Elevation Plane 3-dB Beamwidth 33 Degrees 27 Degrees
Nominal Azimuth Plane 3-dB Beamwidth 31 Degrees 31 Degrees
V-Pol Maximum Sidelobe Level -15 dBc -12 dBc
H-Pol Maximum Sidelobe Level -10 dBc -12 dBc
Front-to-Back Ratio > 30 dB > 30 dB
Connector Type N-Female Bulkhead
Length 14.5 in. (36.8 cm)
Width 20 in. (50.7 cm)
Height 0.8 in. (2.11 cm)
Weight 81.1 oz. (2.3 kg)
Water/Foreign Body Ingress IP67
Operational Wind 100 MPH
Operating Temperature Range -40° C to 85° C

149
Cisco Aironet Four-Port Dual-Band Polarization-Diverse Antenna (AIR-ANT2513P4M-N)
5 GHz Antenna Radiation Patterns
2.4 GHz Ports A&C Azimuth Plane 2.4 GHz Ports A&C Elevation Plane
2.4 GHz Ports B&D Azimuth Plane 2.4 GHz Ports B&D Elevation Plane

150
Cisco Aironet Four-Port Dual-Band Polarization-Diverse Antenna (AIR-ANT2513P4M-N)
Antenna and Bracket Dimensions
Figure 2 and Figure 3 show the overall dimensions of the antenna and bracket.
5 GHz Ports A&C Azimuth Plane 5 GHz Ports A&C Elevation Plane
5 GHz Ports B&D Azimuth Plane 5 GHz Ports B&D Elevation Plane

151
Cisco Aironet Four-Port Dual-Band Polarization-Diverse Antenna (AIR-ANT2513P4M-N)
Figure 2 Antenna and Bracket Dimensions (in millimeters)
Figure 3 Rear View of Antenna (dimensions in millimeters)

152
Cisco Aironet Four-Port Dual-Band Polarization-Diverse Antenna (AIR-ANT2513P4M-N)
System Requirements
This antenna is designed for use with Cisco Aironet 3702P and 1570 series access points. The antenna can be mounted on a
wall, a ceiling, or a pole with a maximum diameter of 5 inches (12.7 cm).
Safety Instructions
WARNING: IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause
bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its
translation in the translated safety warnings that accompanied this device. Statement 1071
WARNING: SAVE THESE INSTRUCTIONS Only trained and qualified personnel should be allowed to install, replace, or service
this equipment.Statement 1030
Follow these safety instructions when installing your antenna.
Plan your installation procedure carefully and completely before you begin.
If you are installing an antenna for the first time, for your own safety as well as others, seek professional assistance. Consult
your dealer, who can explain which mounting method to use for the location where you intend to install the antenna.

153
Cisco Aironet Four-Port Dual-Band Polarization-Diverse Antenna (AIR-ANT2513P4M-N)
Select your installation site with safety, as well as performance, in mind. Remember that electric power cables and
telephone lines look alike. For your safety, assume that any line is an electric power line until determined otherwise.
Call your local power company or building maintenance organization if you are unsure about cables close to your mounting
location.
When installing your antenna, do not use a metal ladder. Do dress properly: shoes with rubber soles and heels, rubber
gloves, and a long sleeved shirt or jacket.
If an accident or emergency occurs with the power lines, call for qualified emergency help immediately.
Installation Notes
Because antennas transmit and receive radio signals, they are susceptible to RF obstructions and common sources of
interference that can reduce throughput and range of the device to which they are connected. Follow these guidelines to ensure
the best possible performance:
Mount the antenna to utilize its propagation characteristics. This antenna is designed to radiate energy in a somewhat
narrow beam from the front of the antenna. It should be aimed into the intended coverage area.
Keep the antenna away from metal obstructions such as heating and air-conditioning ducts, large ceiling trusses, building
superstructures, and major power cabling runs. If necessary, use a rigid conduit to lower the antenna away from these
obstructions.
The density of the materials used in a building’s construction determines the number of walls the signal must pass through
and still maintain adequate coverage. Consider the following before choosing the location to install your antenna:
—Signals penetrate paper, vinyl and drywall the easiest. A signal can penetrate five or six walls constructed of drywall or
wood.
—Signals are more heavily attenuated passing through concrete and solid-wood walls.
—Signals often reflect off thick metal walls and may not penetrate at all.
Install the antenna away from microwave ovens and 2-GHz cordless phones. These products can cause signal interference
because they operate in the same frequency range as the device to which your antenna is connected.
Choosing a Mounting Location
The antenna should be mounted clear of any obstructions to the side or front of the enclosure. Keep in mind that this antenna
should be aimed into the intended coverage area, so you should mount the antenna so that the desired mechanical tilt can be
achieved. If possible, mount the antenna near the access point so you can use the shortest possible connecting cables.
Installing the Antenna
You can install the antenna on any flat surface or on a pole with a minimum diameter of 2 inches (5.08 cm) and a maximum
diameter of 5 inches (12.7 cm). The antenna and one mounting flange are connected together when shipped. When mounting
the antenna you need to assemble the bracket hardware, connect the antenna and bracket to the mounting surface, and adjust
the antenna orientation.
Contents of Antenna Bracket Kit
Figure 4 shows the parts included with the antenna bracket.

154
Cisco Aironet Four-Port Dual-Band Polarization-Diverse Antenna (AIR-ANT2513P4M-N)
Figure 4 Antenna Bracket Kit Contents
NOTE: One flange (not pictured here) ships attached to the antenna. The flange pictured here is the one that you attach to the
wall or the pole.
Tools and Equipment Required
You will need these tools to loosen and tighten the adjustment bolts on the bracket:
A 1/2 in. (13-mm) wrench or socket
To mount the antenna on a wall or ceiling, you will need these supplies:
Four mounting screws or bolts and wall anchors
NOTE: The fasteners and mounting surface should be capable of maintaining a minimum pullout force of 150 pounds (68 kg) to
support the weight of the antenna and bracket plus the potential wind loading on the antenna.
1Mounting flange 5Flat washers
2Mounting arm 6Lock washers
3Arm attachment bolts (5/16-18 x 1-5/8") 7Arm attachment nuts (5/16-18)
4Serrated washers 8Hose clamps (50 – 135 mm adjustment)

155
Cisco Aironet Four-Port Dual-Band Polarization-Diverse Antenna (AIR-ANT2513P4M-N)
To mount the antenna on a pole or mast, you will need either or both of these supplies:
Slotted screwdriver to tighten the screws on the hose clamps
A 5/16 in. (8mm) socket or box wrench
NOTE: The pole or mast must be rigid enough to hold the weight of the antenna plus the associated forces produced by wind
loads. In addition, the pole or mast must be structurally strong enough to withstand the clamping force of the hose clamps.
You may need the following tools and equipment, which are not provided:
A drill and drill bit
A pencil
Mounting on a Wall or Ceiling
Follow these steps to mount your antenna on a wall or ceiling.
1. Remove the antenna and bracket hardware from the shipping container.
2. Determine the mounting location for the antenna.
NOTE: The fasteners and mounting surface should be capable of maintaining a minimum pullout force of 150 pounds (68
kg) to support the weight of the antenna plus the potential wind loading on the antenna.
3. Attach the mounting bracket to the wall or ceiling using four screws or bolts and anchors through the holes on the bracket.
Figure 5 shows the wall-mount bracket.
Figure 5 Wall-Mount Bracket and Dimensions (in millimeters)
4. Assemble the bracket hardware as shown in Figure 6.
4 slotted holes
for hose clamps

156
Cisco Aironet Four-Port Dual-Band Polarization-Diverse Antenna (AIR-ANT2513P4M-N)
Figure 6 Assembling the Bracket Hardware
5. Make sure you orient the antenna correctly (note the arrow on the back of the antenna that indicates the top of the antenna).
Use a 1/2 in. (13-mm) wrench to loosen the elevation adjustment bolt and the elevation pivot bolt.
6. Adjust the azimuth (side-to-side position) and elevation (up-and-down position) of the antenna. Loosen the adjustment
bolts slightly to allow for adjustment. Azimuth angle can be adjusted ±25 degrees and elevation can be adjusted ±60
degrees. You can use the azimuth and elevation markings on the mounting arm and the wall flange as a guide.
7. After you adjust the antenna position, tighten the adjustment bolts and the pivot bolts. Tighten all bolts to 18.7 +/- 5 lb-ft
(25.4 Nm).
8. Connect the antenna cables to the access point. The antenna ports are labeled A through D, from left to right.
—On the AP3702P, connect the antenna port A to connector A on the access point, antenna port B to connector B, and
so on.
—On the AP1570, connect antenna port A to Port 1 on the AP, antenna port B to port 2 on the AP, and so on.
See the Suggested Cable section for cable recommendations.