Cisco LightStream 1010 Manual

Cisco Firepower 1010 Hardware Installation Guide
First Published: 2019-07-24
Last Modified: 2019-09-26
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of
the UNIX operating system. All rights reserved. Copyright ©1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com
go trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any
other company. (1721R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown
for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
©2011 Cisco Systems, Inc. All rights reserved.
©2019 Cisco Systems, Inc. All rights reserved.

CONTENTS
Overview 1
CHAPTER 1
Features 1
Package Contents 4
Serial Number Location 5
Front Panel 6
Rear Panel 6
Status LEDs 7
Hardware Specifications 9
Product ID Numbers 10
Power Cord Specifications 10
Installation Preparation 17
CHAPTER 2
Installation Warnings 17
Position the Chassis 20
Safety Recommendations 20
Maintain Safety with Electricity 21
Prevent ESD Damage 21
Site Environment 22
Site Considerations 22
Power Supply Considerations 22
Rack Configuration Considerations 23
Mount the Chassis 25
CHAPTER 3
Unpack and Inspect the Chassis 25
Desktop-Mount the Chassis 26
Wall-Mount the Chassis 26
Cisco Firepower 1010 Hardware Installation Guide
iii

Rack-Mount the Chassis 29
Connect to the Console Port 33
CHAPTER 4
Connect to the Console Port with Microsoft Windows 33
Connect to the Console Port with Mac OS X 35
Connect to the Console Port with Linux 35
Cisco Firepower 1010 Hardware Installation Guide
iv
Contents

CHAPTER 1
Overview
•Features, on page 1
•Package Contents, on page 4
•Serial Number Location, on page 5
•Front Panel, on page 6
•Rear Panel, on page 6
•Status LEDs, on page 7
•Hardware Specifications, on page 9
•Product ID Numbers, on page 10
•Power Cord Specifications, on page 10
Features
The Cisco Firepower 1010 security appliance is an NGFW desktop product in the Cisco Firepower family of
devices with PoE+ and L2 switch support.
The PoE+ and L2 switch features are supported starting with Firepower Version 6.5.
Note
The Firepower 1010 supports Cisco Firepower software version 6.4 and later. See the Cisco Firepower
Compatibility Guide, which provides Cisco Firepower software and hardware compatibility, including operating
system and hosting environment requirements, for each supported Firepower version.
See Product ID Numbers, on page 10 for a list of the product IDs (PIDs) associated with the Firepower 1010.
The following figure shows the Cisco Firepower 1010.
Cisco Firepower 1010 Hardware Installation Guide
1

Figure 1: Firepower 1010
The following table lists the features for the Firepower 1010.
Table 1: Firepower 1010 Features
DescriptionFeature
1 RUForm factor
Desktop mount
Wall mount (Cisco part number 69-100647-01)
Rack mount (Cisco part number 69-100648-01)
Mounting
Side-to-side
No fan
Airflow
One 4-core Intel CPUProcessor
8-GB DDR4 DRAMMemory
8 GB (internal)Boot partition
Marvell SOHO 88E6390
First supported in Firepower Verion 6.5.
Note
L2 switch
One Gigabit Ethernet RJ-45 10/100/1000 BaseT
Restricted to network management access; connect with an RJ-45 cable
Management
port
One RJ-45
Use to access management through an external system
Console port
One USB Mini B
Use to access management through an external system
USB Mini B
port
One USB 3.0 Type A
Use to attach an external device such as storage
USB port
Cisco Firepower 1010 Hardware Installation Guide
2
Overview
Features

Eight Gigabit Ethernet RJ-45 10/100/1000 BaseT
Each RJ-45 (8P8C) copper port supports auto MDI/X as well as auto-negotiation for
interface speed, duplex, and other negotiated parameters, and are MDI/MDIX-compliant.
The ports are numbered (from top to bottom, left to right) 1, 2, 3, 4, 5, 6, 7, 8. Each port
includes a pair of LEDs, one each for connection status and link status. The ports are
named and numbered Gigabit Ethernet 1/1 through Gigabit Ethernet 1/8.
You can use ports 7 and 8 as PoE+ ports. PoE+ is first supported in Firepower
Version 6.5.
Note
Network ports
Ports 7 and 8 are PoE+ ports; first supported in Firepower Version 6.5.
Note
PoE+ controller
card
Accepts a standard Kensington T-bar locking mechanism for securing the chassisLock slot
A small recessed button that if pressed for longer than three seconds resets the chassis to
its default state following the next reboot. Configuration variables are reset to factory
default, but the flash is not erased and no files are removed.
Reset button
No
To shut down the Firepower 1010, remove the AC power supply.
To shut down the Firepower 1010 gracefully, see the "Power Off the Device"
topic for FDM and FMC in the Cisco Firepower 1010 Getting Started Guide.
Note
Power switch
The chassis is powered on when you plug in the AC power supply.Power cord
socket
One external AC power supply
The power supply has a total of 115 W of power. There is 55 W of +12-V system power
and 60 W of -53.5-V PoE power.
PoE+ is first supported in Firepower Version 6.5.
Note
Use the power supply (part number 341-100765-01) that shipped with the
chassis. It supports PoE+.
Note
AC power
supply
One 200-GB M.2 SATA SSD drive
The drive is used by the software; there is no user access to the drive.
The drive is not field-replaceable; you must return the chassis to Cisco for drive
replacement.
Storage
Four rubber feet on the bottom of the chassis
The rubber feet are needed for proper cooling. Do not remove them.
Note
Rubber feet
Console Ports
The Firepower 1010 has two external console ports, a standard RJ-45 port and a USB Mini B serial port.
Only one console port can be active at a time. When a cable is plugged into the USB console port, the
RJ-45 port becomes inactive. Conversely, when the USB cable is removed from the USB port, the RJ-45
Cisco Firepower 1010 Hardware Installation Guide
3
Overview
Features

port becomes active. The console ports do not have any hardware flow control. You can use the CLI to
configure the chassis through either serial console port by using a terminal server or a terminal emulation
program on a computer.
• RJ-45 (8P8C) port—Supports RS-232 signaling to an internal UART controller. The RJ-45 console
port does not support a remote dial-in modem. You can use a standard management cable (Cisco
part number 72-3383-01) to convert the RJ45-to-DB9 connection if necessary.
•USB Mini B port—Lets you connect to a USB port on an external computer. For Linux and Macintosh
systems, no special driver is required. For Windows systems, you must download and install a USB
driver (available on software.cisco.com). You can plug and unplug the USB cable from the console
port without affecting Windows HyperTerminal operations. We recommend shielded USB cables
with properly terminated shields. Baud rates for the USB console port are 1200, 2400, 4800, 9600,
19200, 38400, 57600, and 115200 bps.
For Windows operating systems, you must install a Cisco Windows USB Console Driver on any PC
connected to the console port before using the USB console port. See Connect to the Console Port with
Microsoft Windows, on page 33 for information on installing the driver.
Note
External Flash Storage
The chassis contains a standard USB Type A port that you can use to attach an external device. The USB
port can provide output power of 5 V and up to a maximum of 1A (5 USB power units).
• External USB drive (optional)—You can use the external USB Type A port to attach a data-storage
device. The external USB drive identifier is disk1. When the chassis is powered on, a connected
USB drive is mounted as disk1 and is available for you to use. Additionally, the file-system
commands that are available to disk0 are also available to disk1, including copy,format,delete,
mkdir,pwd,cd, and so on.
• FAT-32 File System—The Firepower 1010 only supports FAT-32-formatted file systems for the
external USB drive. If you insert an external USB drive that is not in FAT-32 format, the system
mounting process fails, and you receive an error message. You can enter the command format
disk1: to format the partition to FAT-32 and mount the partition to disk1 again; however, data might
be lost.
Package Contents
The following figure shows the package contents for the Firepower 1010. Note that the contents are subject
to change and your exact contents might contain additional or fewer items.
Cisco Firepower 1010 Hardware Installation Guide
4
Overview
Package Contents

Figure 2: Firepower 1010 Package Contents
USB console cable (Type A to Type B)2Chassis1
Power supply4Power cord3
Start Here: Cisco Firepower 1010
This document tells how to cable and set up the
Firepower 1010 for FTD with FDM and ASA
with ASDM, and it sends you to the online Useful
Links document to continue your configuration.
5
Serial Number Location
You can view the serial number and additional model information on the compliance label located on the
bottom of the chassis. The following figure shows a sample compliance label.
Cisco Firepower 1010 Hardware Installation Guide
5
Overview
Serial Number Location

Figure 3: Compliance Label on the Firepower Chassis
Front Panel
The following figure shows the front panel of the Firepower 1010. Note that there are no connectors or LEDs
on the front panel.
Figure 4: Firepower 1010 Front Panel
Rear Panel
The following figure shows the rear panel of the Firepower 1010. See Status LEDs, on page 7 for a description
of the LEDs.
Cisco Firepower 1010 Hardware Installation Guide
6
Overview
Front Panel