Cisco WEC600N User manual

QUICK INSTALLATION GUIDE
Dual-Band
Wireless-N
ExpressCard
Model: WEC600N
Package Contents
Dual-Band Wireless-N ExpressCard•
Setup Wizard CD-ROM•
User Guide on CD-ROM•
Quick Installation Guide•

InstallationWEC600N
3Dual-Band Wireless-N ExpressCard
Installation1
The ExpressCard is installed and set up using the Setup Wizard on the
enclosed Setup Wizard CD.
IMPORTANT: Do not install the ExpressCard in your computer
until you are instructed to do so, or the ExpressCard will not
install correctly.
A. Insert the Setup Wizard CD into
your CD-ROM drive.
NOTE: Windows or other personal firewalls may ask for
permission to run the software or program. You will need to allow
the software to run in order to continue.
B. The Welcome screen appears.
Click the Click Here to Start
button.
Insert the CD-ROM
Click Here to Start

Installation WEC600N
4 Dual-Band Wireless-N ExpressCard
C. Read the License Agreement,
and select I accept the terms in
the License Agreement.
Click Next to continue the
installation.
D. Locate an available ExpressCard
slot on your computer.
Insert the ExpressCard into the
slot until it locks into place.
Click Next.
If your computer runsE. Windows XP, proceed to “Section 2: Setup for
Windows XP”.
If your computer runs Windows Vista, proceed to “Section 3: Setup for
Windows Vista”.
License Agreement
Insert the Adapter

Setup for Windows XPWEC600N
5Dual-Band Wireless-N ExpressCard
Setup for Windows XP2
The ExpressCard supports Wi-Fi Protected Setup, a feature that makes it
easy to set up your wireless network.
If the Available Wireless Networks
screen appears, your router does not
support this feature. Proceed to the
“No Wi-Fi Protected Setup” section.
If the Connect to a Network screen
appears, the ExpressCard detects a
router that supports Wi-Fi Protected
Setup. Proceed to the “Wi-Fi
Protected Setup”section.
No Wi-Fi Protected Setup
From the Available Wireless Networks screen, you can launch one of the two
setup methods.
If your network appears on the Available Wireless Networks screen, proceed
to step A. If your network does not appear on the Available Wireless
Networks screen, click Advanced Setup and follow the on-screen prompts.
Available Wireless Networks
Connect to a Network

Setup for Windows XP WEC600N
6 Dual-Band Wireless-N ExpressCard
A. On the Available Wireless
Networks screen, the available
networks are listed in the table.
Select your network, and then
click Connect.
If your network does not use wireless security, proceed to the “WirelessB.
Security Disabled” section. If your network uses wireless security,
proceed to the Wireless Security Enabled” section.
Wireless Security Disabled
A. Click Connect Anyway.
B. Click Finish.
Available Wireless Networks
Click Connect Anyway
Congratulations

Setup for Windows XPWEC600N
7Dual-Band Wireless-N ExpressCard
C. The Status screen of the Wireless
Network Monitor appears the
first time you run the Setup
Wizard. To exit the Monitor, click
the Xin the upper right corner.
NOTE: After the ExpressCard is installed, the Wireless Network
Monitor screen opens, and its icon appears in your computer’s
system tray. You can double-click the icon to open the Monitor
if you want to find available wireless networks or change the
ExpressCard’s configuration. For detailed information on the
Monitor, refer to the User Guide on the CD-ROM.
Congratulations! Setup is complete.
Wireless Security Enabled
If your network has wireless security, you will see one of these wirelessA.
security screens. Follow the instructions for the screen you see.
WPA2-Personal Key Needed for Connection
1. Enter the Passphrase (also
called a pre-shared key) of your
wireless network. It must have
8-63 characters.
Click2. Connect and go to step B.
Connected to the Network
WPA2-Personal Key Needed for Connection

Setup for Windows XP WEC600N
8 Dual-Band Wireless-N ExpressCard
WPA-Personal Key Needed for Connection
1. Enter the Passphrase (also
called a pre-shared key) of your
wireless network. It must have
8-63 characters.
Click2. Connect and go to step B.
WEP Key or Passphrase Needed for Connection
1. Enter the Passphrase or WEP
Key.
Passphrase The Passphrase
is case-sensitive and must
have 16 or fewer alphanumeric
characters.
WEP Key For 64-bit encryption,
enter 10 hexadecimal characters
(“0” to “9” and “A” to “F”). For
128-bit encryption, enter 26
hexadecimal characters.
Click2. Connect and go to step B.
B. On the Congratulations screen,
click Finish.
WPA-Personal Key Needed for Connection
WEP Key or Passphrase Needed for
Connection
Congratulations

Setup for Windows XPWEC600N
9Dual-Band Wireless-N ExpressCard
C. The Status screen of the Wireless
Network Monitor appears the
first time you run the Setup
Wizard. To exit the Monitor, click
the Xin the upper right corner.
NOTE: After the ExpressCard is installed, the Wireless Network
Monitor screen opens, and its icon appears in your computer’s
system tray. You can double-click the icon to open the Monitor
if you want to find available wireless networks or change the
ExpressCard’s configuration. For detailed information on the
Monitor, refer to the User Guide on the CD-ROM.
Congratulations! Setup is complete.
Wi-Fi Protected Setup
A. If your router supports Wi-Fi
Protected Setup, click Use Wi-Fi
Protected Setup.
If you are not sure whether your
router supports Wi-Fi Protected
Setup or you want to manually
connect to your router, click
Skip. Then refer to the “No Wi-Fi
Protected Setup”section for
instructions.
Connected to the Network
Connect to a Network

Setup for Windows XP WEC600N
10 Dual-Band Wireless-N ExpressCard
B. Press the Wi-Fi Protected
Setup button on the Router.
Within two minutes, click the
Wi-Fi Protected Setup button
on this screen.
C. The ExpressCard connects to the
network.
D. Click Print to print out your
wireless network settings. Then
click Finish.
Wi-Fi Protected Setup
Connecting to the Network
Congratulations