Cisco 1401 User manual

Quick Start Guide
INSTALLING YOUR CISCO 1401 ROUTER
UNPACK THE BOX
INSTALL THE ROUTER
VERIFY YOUR INSTALLATION
Cisco 1401
Hub
PC
PC
Internet
ADSL connection
DSL modem
PC
PC
PC
PC
Server
Server
1
2
3

2
Unpack the Box
1
When you unpack the box that contains your Cisco 1401 router, you should find the items
shown below.
Items You Must Provide:
You must provide the following items to completely install the router:
• 10BaseT Ethernet hub or switch to connect the router to the local network.
• ATM DSL modem to connect the router to the ADSL line.
• RJ-11-to-RJ-11 cable to connect the DSL modem to the ADSL line.
DB-9 to RJ-45 console adapter
(light gray)
DB-25 to RJ-45 console adapter
(light gray)
Quick
Start
Guide
Product documentation
12411
Installation
and
Configuration
Guide
Documentation
CD-ROM
Console cable
(light blue, RJ-45 to RJ-45)
Power cord (black)
Cisco 1401 router
Cisco 1400
SERIES
AL
LPACT
CARRIER
COLLACTOKPWR
SYSTEM ETHERNET WAN
Console cable
(yellow, RJ-45 to RJ-45) ATM 25 cable (light green, RJ-45 to RJ-45)

3
Install the Router
2
A. Connect the router to the local network
Use the included yellow Ethernet cable for connecting the router to the local Ethernet network.
For more information on this cable, refer to the “Cabling Specifications” chapter in the
hardware installation guide that came with the router.
Step 1 Connect one end of the yellow Ethernet cable to the yellow ETHERNET port.
Step 2 Connect the other end to a port on the Ethernet hub or switch.
Cisco 1401
CONSOLE
ATM 25 ETHERNET
LNK
OK FLASH PC CARD
12413
AUI 871
Ethernet port
Straight-through
Ethernet cable Ethernet hub or switch

4
Install the Router (continued)
2
B. Connect the router to the ADSL line
You must provide an ATM DSL modem (for example, a Cisco 625 or Cisco 626 CAP modem),
a crossover RJ-45-to-RJ-45 cable, and an RJ-11-to-RJ11 cable for this connection.
Step 1 Connect one end of the RJ-45 cable to the light-green ATM 25 port on the router.
Step 2 ConnecttheotherendoftheRJ-45cabletotheappropriateportontheCAPmodem.
For the Cisco 625 and Cisco 626, this is the DATA port.
Step 3 Connect one end of the RJ-11 cable to the ADSL port on the CAP modem. For the
Cisco 625 and Cisco 626, this is the LINE port.
Note: Refer to the documentation that came with the modem if you are not sure which
modem port connects to the router and which port connects to the ADSL line.
Step 4 Connect the other end of the RJ-11 cable to the ADSL wall jack.
Cisco 1401
CONSOLE
ATM 25 ETHERNET
LNK
OK FLASH PC CARD
RESET
LINE
DATA
POWER
12415
ADSL
(RJ-11)
wall jack
DSL modem
RJ-11 cable
RJ-45 cable ATM 25 port

5
Install the Router (continued)
2
C. Connect a PC to the router
To use Cisco IOS software to configure the router, it must be connected to a terminal or to a
PC with terminal-emulation software. Terminal emulation software should be configured with
the following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit.
Take the following steps to connect the router to one of these devices:
Step 1 Connect one end of the light-blue console cable (included) to the CONSOLE port on
the router rear panel.
Step 2 Depending on the console port connector (DB-25 or DB-9) on your terminal or PC,
connect one of the gray adapters (included) to the other end of the console cable.
Step 3 Connect the gray adapter to the DB-25 or DB-9 connector on your terminal or PC.
Cisco 1401
CONSOLE
ATM 25 ETHERNET
LNK
OK FLASH PC CARD
12419
Light blue
console cable To PC or terminal

6
Install the Router (continued)
2
D. Connect the power cord
Step 1 Connect the power-supply cord to the power socket (labeled +5,+12,-12 VDC) on
the rear panel.
Step 2 Connect the other end of the cord to a power outlet.
Step 3 Turn on the router by pressing the power switch to the ON ( | ) position.
Step 4 Confirm that the router has power by checking that the PWR LED on the front panel
is on.
Cisco 1401
CONSOLE
ATM 25 ETHERNET
LNK
OK FLASH PC CARD
12417
Power switch

7
Verify Your Installation
3
After the router is powered on, the following LEDs confirm that you have correctly installed
your router.
For More Information
For more information about installing or configuring your Cisco 1401 router, refer to the
following sources:
•Cisco 1401 Router Installation and Configuration Guide (in the accessory kit).
• The Cisco Connection Online card (in the accessory kit), which lists telephone numbers,
e-mail addresses, and World Wide Web URLs for getting information directly from Cisco
Systems.
LED Location What to Look for
PWR Front On when power is being supplied to the router.
OK Front • One blink per second when the router is in ROM monitor
mode.
• Several blinks per second when the router is running the boot
image in ROM monitor.
• On steady when the Cisco IOS software is loaded and
functional.
LNK Rear On when the router is correctly connected to the local Ethernet
network through the ETHERNET port.
WAN CARRIER Front On when the router has synchronized with the ADSL switch.
ETHERNET ACT Front Blinking when there is network traffic on the local Ethernet LAN.
OK Rear On when the Flash PC card is correctly installed in the router. If
this LED is off, refer to the installation and configuration guide
that came with your router for instructions on how to reinstall the
Flash PC card.

Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]
European Headquarters
Cisco Systems Europe s.a.r.l.
Parc Evolic, Batiment L1/L2
16 Avenue du Quebec
Villebon, BP 706
91961 Courtaboeuf Cedex
France
http://www-europe.cisco.com
Tel: [phone]
Fax: [phone]
Americas
Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
Fax: [phone]
Asia Headquarters
Nihon Cisco Systems K.K.
Fuji Building, 9th Floor
3-2-3 Marunouchi
Chiyoda-ku, Tokyo 100
Japan
http://www.cisco.com
Tel: [phone]
Fax: [phone]
Printed in the USA on recycled paper containing 10% postconsumer waste.
Cisco Systems has more than 200 offices in the following countries. Addresses, phone numbers, and fax numbers are listed on the
Cisco Connection Online Web site at http://www.cisco.com.
Argentina •Australia •Austria •Belgium •Brazil •Canada •Chile •China (PRC) •Colombia •Costa Rica •Czech Republic •Denmark
England •France •Germany •Greece •Hungary •India •Indonesia •Ireland •Israel •Italy •Japan •Korea •Luxembourg •Malaysia
Mexico •The Netherlands •New Zealand •Norway •Peru •Philippines •Poland •Portugal •Russia •Saudi Arabia •Scotland •Singapore
South Africa •Spain •Sweden •Switzerland •Taiwan, ROC •Thailand •Turkey •United Arab Emirates •United States •
Copyright © 1998 Cisco Systems, Inc. All rights reserved. AccessPath, Any to Any, AtmDirector, the CCIE logo, CD-PAC, Centri, the Cisco Capital logo, CiscoLink, the Cisco Management Connection
logo, the Cisco NetWorks logo, the Cisco Powered Network logo, the Cisco Press logo, the Cisco Technologies logo, ClickStart, ControlStream, DAGAZ, Fast Step, FireRunner, IGX, IOS, JumpStart,
Kernel Proxy, LoopRunner, MGX, Natural Network Viewer, NetRanger, NetSonar, Packet, PIX, Point and Click Internetworking, Policy Builder, RouteStream, Secure Script, SMARTnet, SpeedRunner,
Stratm, StreamView, The Cell, TrafficDirector, TransPath, VirtualStream, VlanDirector, Workgroup Director, and Workgroup Stack are trademarks; Changing the Way We Work, Live, Play, and Learn,
Empowering the Internet Generation, The Internet Economy, and The New Internet Economy are service marks; and BPX, Catalyst, Cisco, Cisco IOS, the Cisco IOS logo, Cisco Systems, the Cisco
Systems logo, Enterprise/Solver, EtherChannel, FastHub, ForeSight, FragmentFree, IP/TV, IPX, LightStream, MICA, Phase/IP, StrataSphere, StrataView Plus, and SwitchProbe are registered trademarks
of Cisco Systems, Inc. in the U.S. and certain other countries. All other trademarks mentioned in this document are the property of their respective owners. (9810R)
DOC-785467=
78-5467-01