Cisco 1760 - VPN Bundle Router User manual

Quick Start Guide
Cisco 1760 Modular Access Router Cabling and Installation
INCLUDING LICENSE AND WARRANTY
1Cisco One-Year Limited Hardware Warranty Terms
2Overview
3Parts List
4Mounting the Router in a Rack
5Installing WIC/VIC Cards
6Connecting the Router to Your Local Network
7Connect Power and Verify Installation
8Connect a PC to the Router Console Port
9Perform Initial Configuration
10 Use the CLI to Configure VoIP
11 Obtaining Documentation
12 Documentation Feedback
13 Cisco Product Security Overview
14 Obtaining Technical Assistance
15 Obtaining Additional Publications and Information

2
1 Cisco One-Year Limited Hardware Warranty Terms
There are special terms applicable to your hardware warranty and various services that you can use during the warranty period.
Your formal Warranty Statement, including the warranties and license agreements applicable to Cisco software, is available on
Cisco.com. Follow these steps to access and download the Cisco Information Packet and your warranty and license agreements
from Cisco.com.
1. Launch your browser, and go to this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/cetrans.htm
The Warranties and License Agreements page appears.
2. To read the Cisco Information Packet, follow these steps:
a. Click the Information Packet Number field, and make sure that the part number 78-5235-03A0 is highlighted.
b. Select the language in which you would like to read the document.
c. Click Go.
The Cisco Limited Warranty and Software License page from the Information Packet appears.
d. Read the document online, or click the PDF icon to download and print the document in Adobe Portable Document
Format (PDF).
Note You must have Adobe Acrobat Reader to view and print PDF files. You can download the reader from Adobe’s
website: http://www.adobe.com
3. To read translated and localized warranty information about your product, follow these steps:
a. Enter this part number in the Warranty Document Number field:
78-10747-01C0
b. Select the language in which you would like to view the document.
c. Click Go.
The Cisco warranty page appears.
d. Read the document online, or click the PDF icon to download and print the document in Adobe Portable Document
Format (PDF).
You can also contact the Cisco service and support website for assistance:
http://www.cisco.com/public/Support_root.shtml.
Duration of Hardware Warranty
One (1) Year
Replacement, Repair, or Refund Policy for Hardware
Cisco or its service center will use commercially reasonable efforts to ship a replacement part within ten (10) working days after
receipt of a Return Materials Authorization (RMA) request. Actual delivery times can vary, depending on the customer location.
Cisco reserves the right to refund the purchase price as its exclusive warranty remedy.
To Receive a Return Materials Authorization (RMA) Number
Contact the company from whom you purchased the product. If you purchased the product directly from Cisco, contact your Cisco
Sales and Service Representative.

3
Complete the information below, and keep it for reference.
2 Overview
This document describes the hardware installation and software configuration steps necessary to install your Cisco 1760
modular access router with its complement of WAN interface cards (WICs) and voice interface cards (VICs). Additional
documentation can be found on Cisco.com.
Product Serial Number Location
The serial number label for Cisco 1760 router is located on the rear of the chassis, in the lower right-hand corner.
3 Parts List
Your router package should include the following items:
•One Cisco 1760 modular access router
•One blue RJ-45-to-DB-9 console cable
•One DB-25-to-DB-9 adapter
•One black power supply cord
•Cable guide
•Rack-mounting brackets
•Product documentation
4 Mounting the Router in a Rack
Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure
that the system remains stable. The following guidelines are provided to ensure your safety.
•This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
•When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component
at the bottom of the rack.
•If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.
The rack-mounting brackets supplied with the router can be attached to a 19- or 24-inch rack. Figure 1 shows the bracket
mounting points that attach to the rack.
Company product purchased from
Company telephone number
Product model number
Product serial number
Maintenance contract number

4
Figure 1 Bracket Mounting Points
To install the router in a 19-inch or a 24-inch standard rack, follow the instructions described in these procedures:
•Attaching Brackets to the Router
•Attaching Brackets to the Rack
•Attaching the Optional Cable Guide
Attaching Brackets to the Router
The bracket orientation and the screws you use depend on whether you are attaching the brackets for a 19-inch or a 24-inch
rack. Use two of the supplied screws to attach each bracket, according to the following guidelines:
•For a 19-inch rack, use the supplied number-8 Phillips flat-head screws to attach the long side of the bracket to the router.
•For a 24-inch rack, use the supplied number-8 Phillips truss-head screws to attach the short side of the bracket to the router.
Figure 2 shows how to attach brackets to the two sides of the router with the front panel forward.
Figure 2 Attaching Brackets for 19- and 24-Inch Racks
38398
19" rack
mount point
19" rack
mount point
24" rack
mount point
24" rack
mount point
PVDM 0
OK
OK
PWR1
0
SLOT 0
OK
PVDM 1
OK
MOD
OK
1
0
SLOT 1
OK
Phillips
flat-head
screws
19" Configuration
60942

5
Attaching Brackets to the Rack
After the brackets are attached to the router, use the four supplied number-12 Phillips machine screws to securely attach the
brackets to the rack, as shown in Figure 3.
Caution Make sure that the fans on the side of the chassis are not blocked.
Figure 3 Attaching Brackets to the Rack
Attaching the Optional Cable Guide
Cisco recommends attaching the cable guide to prevent the cables from obscuring the front panel of the router and the other
devices installed in the rack. If the router is in a 19-inch or 24-inch rack, use the supplied black screw, as shown in Figure 4, to
attach the cable guide to the left or right bracket.
PVDM 0
OK
OK
PWR1
0
SLOT 0
OK
PVDM 1
OK
MOD
OK
1
0
SLOT 1
OK
Phillips
truss-head
screws
24" Configuration
60943
Cisco 1700
Series
10/100 ETHERNET AUX
CONSOLE
PVDM 0
OK
OK
PWR 1
0
SLOT0
OK
PVDM 1
OK
MOD
OK
1
0
SLOT1
OK
LINK
100
FDX
ACT COL 1
0
SLOT2
OK
1
0
SLOT3
OK
60941
Phillips machine screws

6
Figure 4 Attaching the Cable Guide to the Router
5 Installing WIC/VIC Cards
The router has four card slots that hold Cisco WICs and VICs. Either one or two WICs may be installed, with the remaining
slots holding VICs, as desired. If no WICs are present in the slots, up to four VICs may be installed. Each WIC has one or two
WAN ports, and each VIC has two or more voice ports. This section describes the procedure for installing a WIC or a VIC in
the router.
Note For details on specific WICs and VICs, on how to connect a WIC to the WAN line or a VIC to the telephone and fax
line, and on how to configure the interface with Cisco IOS software, refer to the Cisco WAN Interface Cards Hardware
Installation Guide that came with the cards.
Safety Information
This section lists safety warnings that you should be aware of before installing WICs or VICs in the router. To see translated
versions of these warnings, refer to the Regulatory Compliance and Safety Information for the Cisco 1700 Routers document
that came with the router.
Warning Before working on a system that has an on/off switch, turn off the power and unplug the power cord.
Warning Only trained and qualified personnel should be allowed to install or replace this equipment.
Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and
watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld
the metal object to the terminals.
Warning Before opening the chassis, disconnect the telephone-network cables (from the card) to avoid contact with the
telephone-network voltages.
Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Cisco 1700
Series
10/100 ETHERNETAUX
CONSOLE
PVDM0
OK
OK
PWR1
0
SLOT0
OK
PVDM1
OK
MOD
OK
1
0
SLOT1
OK
LINK
100
FDX
ACTCOL 10
SLOT2
OK
1
0
SLOT3
OK
65286
Cable guide screw

7
Caution Do not connect a WAN, telephone or fax cable to the card until you have completed the installation procedure.
Card Installation
Follow these steps to insert a card in the router:
Step 1 Make sure the router is turned off and is disconnected from AC power.
Caution Power must be removed from the system prior to installing or removing WICs or VICs to avoid damaging them.
When WICs or VICs are pushed into or pulled out of a router that is powered up, there is a very good chance that
they could be damaged electrically and will no longer function.
Step 2 Loosen the thumbscrews on the WIC or VIC slot cover, as shown in Figure 5.
Figure 5 Removing a WIC or VIC Slot Cover
You should be able to loosen the screws using your fingers; however, if the screws are very tight, you may need to use a Phillips
screwdriver.
Step 3 Remove the metal plate that covers the card slot.
Step 4 Hold the card by the edges on either side of the card front panel, and line up the card edges with the guides inside the
card slot, as shown in Figure 6.
Figure 6 Inserting a WIC or VIC in the Router
Step 5 Insert the card in the slot, and gently push it into the router until the front panel of the card is flush with the router.
1Interface Card 2Guides
60950
Cisco 1700
Series
10/100ETHERNETAUX
CONSOLE
PVDM 0
OK
OK
PWR 1
0
SLOT0
OK
PVDM 1
OK
MOD
OK
1
0
SLOT1
OK
LINK
100
FDX
ACT COL 1
0
SLOT2
OK
1
0
SLOT3
OK
Cisco 1700
Series
10/100ETHERNETAUX
CONSOLE
PVDM 0
OK
OK
PWR 1
0
SLOT0
OK
PVDM 1
OK
MOD
OK
1
0
SLOT1
OK
LINK
100
FDX
ACT COL 1
0
SLOT2
OK
1
0
SLOT3
OK
1 2
60949

8
Note Slots 2 and 3 accept VICs only. These slots have a small metal tab on the right side that interferes with a similar
tab on WICs, preventing the insertion of WICs by mistake.
Step 6 Tighten the screws that are on the card.
Voice Port Verification
When the router is connected to a PC and you are running the command-line interface, as described in the “Connect a PC to
the Router Console Port” section, you can enter the show voice port command to identify the port numbers of voice interfaces
installed in your router:
Router# show voice port slot-number/port-number
As an example of voice port numbering, if you install VICs in both slot 1 and slot 2 of the router, the ports in each of these slots
would be numbered as follows:
Slot 1—1/0 and 1/1
Slot 2—2/0 and 2/1
Figure 7 shows the Cisco 1760 router front panel and slot numbering.
Figure 7 Cisco 1760 Router Front Panel
6 Connecting the Router to Your Local Network
The router is connected to your local Ethernet network through the yellow 10/100 Ethernet port. You must provide the
following items for this connection:
•A straight-through, RJ-45-to-RJ-45 Ethernet cable
•A 10/100-Mbps Ethernet hub or switch
1WIC/VIC Slot 0 9Ethernet Port
2WIC/VIC Slot 1 10 Ethernet LEDs
3Console Port 11 Slot 1 LEDs
4VIC Slot 2 12 Slot 0 LEDs
5VIC Slot 3 13 MOD OK LED
6Slot 3 LEDs 14 PVDM 0/1 OK LEDs
7Slot 2 LEDs 15 Router OK LED
8Auxiliary Port 16 Power LED
Cisco 1700 Series
10/100 ETHERNET AUX
CONSOLE
PWR OK PVDM 0
OK
PVDM 1
OK
MOD
OK
ACT COL FDX 100 LINKSLOT 0
OK
0 1 SLOT 1
OK
0 1 SLOT 2
OK
0 1 SLOT 3
OK
0 1
60906
1 2 3
10
4 5
16 15 13 9 814 12 11 7 6
THESE SLOTS ACCEPT ONLY VOICE INTERFACE CARDS

9
Warning The ports labeled 10/100-Mbps Ethernet port and Console port are safety extra-low voltage (SELV) circuits. SELV
circuits should only be connected to other SELV circuits. Because BRI circuits are treated like telephone-network
voltage, avoid connecting the SELV circuits to the telephone network voltage (TNV) circuits. (To see translated
versions of this warning, refer to the Regulatory Compliance and Safety Information for Cisco 1700 Routers
document that came with the router.)
Caution Always connect the Ethernet cable to the yellow ports on the router. Do not connect the cable to an ISDN S/T or
U port on a WIC or to an NT1 that is connected to a WIC. Accidentally connecting the cable to the wrong port can
damage your router.
Follow these steps to connect the router to your local network:
Step 1 Connect one end of the Ethernet cable to the yellow Ethernet port (labeled 10/100-Mbps Ethernet port), as shown in
Figure 8.
Figure 8 Connecting the Router to the Local Network
Step 2 Connect the other end of the Ethernet cable to a network port on the hub or switch.
7 Connect Power and Verify Installation
Read the following warnings before connecting the power to the router.
Warning The power supply is designed to work with TN power systems.
110/100 Ethernet port 3Straight-through Ethernet cable
2Ethernet hub or switch
Cisco 1700
Series
10/100 ETHERNET AUX
CONSOLE
ETHERNET
SPEED
1
5
2
6
3
7
4
8
LED
100BaseTX SOLID
10BaseT BLINK
1X 2X 3X 4X
5X 6X 7X MDI MDI-X
8X
PVDM0
OK
OK
PWR 1
0
SLOT0
OK
PVDM1
OK
MOD
OK
1
0
SLOT1
OK
LINK
100
FDX
ACT COL 10
SLOT2
OK
1
0
SLOT3
OK
3
2
1
60945

10
Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or
circuit breaker no larger than 120VAC, 15A U.S. (240VAC, 16A international) is used on the phase conductors (all
current-carrying conductors).
Warning This equipment needs to be grounded. Use a green-and-yellow 14 AWG ground wire to connect the host to earth
ground during normal use.
Warning When installing the unit, always make the ground connection first and disconnect it last.
Warning Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground
conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that
suitable grounding is available.
Follow these steps to connect power to the router and to turn the router on:
Step 1 Connect the separate power cord to the power socket on the rear panel, as shown in Figure 9.
Figure 9 Connecting the Power Supply
Step 2 Connect the other end of the separate power cord to a power outlet.
Step 3 Turn the power switch to on ( | ).
Step 4 Verify that you have correctly installed the router by checking the following LEDs:
•PWR—On when power is being supplied to the router.
•LINK—On when the router is correctly connected to the local Ethernet LAN through the 10/100-Mbps Ethernet
port.
•ETH ACT—Blinking when there is network traffic on the local Ethernet LAN.
•SLOT OK—On when a WIC is correctly installed in the slot.
•PVDM 0/1 OK—On when a packet voice data module (PVDM) is correctly installed in its slot and is recognized
by the system.
100-240V~
1.5 MAX/1.5A MAX
50-60 Hz
60948