Cisco 2600 Series User manual

CHAPTER
3-1
Cisco 2600 Series Routers Hardware Installation Guide
OL-2171-02
3
Installing the Router
This chapter guides you through the installation of the Cisco 2600 series routers and includes the
following sections:
•Required Tools and Equipment, page 3-1
•Setting Up the Chassis, page 3-2
•Connecting the DC Power Supply, page 3-12
•Power on the Router, page 3-17
•Connecting to a Network, page 3-17
•Connecting the Console Terminal and Modem, page 3-20
•What to Do After Installing Router Hardware, page 3-22
Warning Onlytrainedandqualifiedpersonnelshouldbeallowedtoinstallorreplacethisequipment.To see
translations of the warnings that appear in this publication, refer to the
Regulatory Compliance
and Safety Information document that accompanied this device.
Required Tools and Equipment
Installation might require some tools and equipment that are not provided as standard equipment with
the router. Following are the tools and parts required for a typical router installation:
•Number 2 Phillips screwdriver.
•Flat-blade screwdrivers: small, 3/16-in. (0.476 cm) and medium, 1/4-in. (0.625 cm).
•Electrostatic discharge (ESD)-preventive wrist strap.
•Screws to secure the rack-mount brackets to the router.
•Grounding lug with attaching screws.
•Cables for connecting a PC or modem to the router (included).
•Cables for connection to the WAN and LAN ports (dependent on configuration):
– Ethernet 10BASE-T cable for connection to an Ethernet port (included).
– Ethernet 100BASE-T cable for connection to a Fast Ethernet port (included).
– Token Ring lobe cable for connection to the Token Ring port (included).

3-2
Cisco 2600 Series Routers Hardware Installation Guide OL-2171-02
Chapter 3 Installing the Router
Setting Up the Chassis
Note For more information on cable specifications, refer to the online document Cisco Modular Access
Router Cabling Specifications on the Documentation CD-ROM that accompanied your router
package and on Cisco.com. For cable ordering information, see “Obtaining Technical Assistance”.
•Ethernet 10BASE-T hub or PC with a network interface card for connection to the Ethernet (LAN)
port(s).
•Console terminal (an ASCII terminal or a PC running terminal emulation software) configured for
9600 baud, 8 data bits, no parity, and 2 stop bits. A terminal is required unless you are using the
AutoInstall procedure. See the “Connecting the Console Terminal and Modem” section on
page 3-20 for instructions on connecting a console terminal.
•Modem for connection to the auxiliary port for remote administrative access. (Optional)
Setting Up the Chassis
You can set the chassis on a desktop, install it in a rack, or mount it on a wall or other flat surface. Use
the procedure in this section that best meets the needs of your network. The sections are as follows:
•Setting the Chassis on a Desktop, page 3-2
•Mounting the Chassis in a Rack, page 3-4
•Mounting the Chassis on the Wall, page 3-10
Cisco 2600 series routers include the following models:
•Cisco 2610 and Cisco 2610XM
•Cisco 2611 and Cisco 2611XM
•Cisco 2612 and Cisco 2613
•Cisco 2620 and Cisco 2620XM
•Cisco 2621 and Cisco 2621XM
•Cisco 2650 and Cisco 2650XM
•Cisco 2651 and Cisco 2651XM
•Cisco 2691
Setting the Chassis on a Desktop
Before setting the router on a desktop, shelf, or other flat, secure surface, perform the following steps to
install the rubber feet:
Step 1 Locate the rubber feet on the black adhesive strip that shipped with the chassis. (See Figure 3-1.)

3-3
Cisco 2600 Series Routers Hardware Installation Guide
OL-2171-02
Chapter 3 Installing the Router Setting Up the Chassis
Figure 3-1 Identifying the Rubber Feet
Step 2 Place the router upside down on a smooth, flat surface.
Step 3 Peel off the rubber feet from the black adhesive strip and place them adhesive-side down onto the five
round, recessed areas on the bottom of the chassis. (See Figure 3-2 and Figure 3-3.)
Figure 3-2 Rubber Feet Location on Cisco 261x, Cisco 262x, Cisco 26xxXM, and Cisco 265x Series
Routers
Rubber feet (5)
Black adhesive strip
H4796
Fan
H4795

3-4
Cisco 2600 Series Routers Hardware Installation Guide OL-2171-02
Chapter 3 Installing the Router
Setting Up the Chassis
Figure 3-3 Rubber Feet Location on Cisco 2691 Router
Step 4 Place the router right-side up on a flat, smooth, secure surface.
Caution Do not place anything on top of the router that weighs more than 10 lb (4.5 kg). Excessive weight on
top could damage the chassis.
Mounting the Chassis in a Rack
This section describes the procedures for rack-mounting the chassis. Cisco 2600 series routers with a
chassis height of 1 rack-unit (1RU) ship with brackets for use with a 19-inch rack or, if specified in your
order, optional larger brackets for use with a 23- or 24-inch rack. Cisco 2600 series routers with a chassis
height of 2 rack-units (2RU) ship with brackets for use with a 19-inch rack. The brackets are shown in
Figure 3-4 and Figure 3-5.
Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. To see translations of the warnings that
appear in this publication, refer to the
Regulatory Compliance and Safety Information document
that accompanied this device. The following guidelines are provided to ensure your safety:
•If the rack contains only one unit, mount the unit at the bottom of the rack.
•If the rack is partially filled, load the rack from the bottom to the top, with the heaviest component
at the bottom of the rack.
72099
Chassis bottom

3-5
Cisco 2600 Series Routers Hardware Installation Guide
OL-2171-02
Chapter 3 Installing the Router Setting Up the Chassis
•If the rack contains stabilizing devices, install the stabilizers before mounting or servicing the unit
in the rack.
Figure 3-4 Brackets for Cisco 261x, Cisco 262x, Cisco 26xxXM, and Cisco 265x Series Routers
Figure 3-5 Brackets for Cisco 2691 Router
Attaching the Brackets to Cisco 261x, Cisco 262x, Cisco 26xxXM, and Cisco 265x Series Routers
To install the chassis in a rack, attach the brackets in one of the following ways:
•With the front panel forward (see Figure 3-6 and Figure 3-7)
•With the rear panel forward (see Figure 3-8 and Figure 3-9)
•In a center-mount rack, with the rear panel forward (see Figure 3-10 through Figure 3-12)
Note Use the screws that came with your router package for attaching the brackets.
Note If you are installing a Cisco 2600 series router in a 19-inch rack with a 17.5-inch opening, orient the
rack-mount brackets so that, when installed, they do not increase the width of the chassis. (See
Figure 3-6.)
If you are installing a Cisco 2600 series router in a 19-inch rack with a 17.75-inch opening or a 23- or
24-inch rack, orient the rack-mount brackets so that, when installed, they increase the width of the
chassis. (See Figure 3-7.)
Bracket for use with a
23-inch or 24-inch rack
Bracket for use
with a 19-inch rack
27711
Narrow bracket for
chassis side opposite fans Wide bracket for chassis side with fans
Slots for
cable tie
attachment
60289
LEFT
RIGHT

3-6
Cisco 2600 Series Routers Hardware Installation Guide OL-2171-02
Chapter 3 Installing the Router
Setting Up the Chassis
Note The following illustrations show how to connect the bracket to one side of the chassis. The second
bracket connects to the opposite side of the chassis.
Figure 3-6 Bracket Installation—Front Panel Forward (19-Inch Rack with a 17.5-Inch Opening)
Note When installed in a 19-inch rack with a 17.75-inch opening, the Cisco 2600 series routers will
protrude beyond the front of the rack.
Figure 3-7 Bracket Installation—Front Panel Forward (19-Inch Rack with a 17.75-Inch Opening or a
23- or 24-Inch Rack)
62676
Note: The second bracket attaches to the other side of the chassis.
62881
Note: The second bracket attaches
to the other side of the chassis.
Brackets for
19-inch rack Brackets for
23-inch or 24-inch rack

3-7
Cisco 2600 Series Routers Hardware Installation Guide
OL-2171-02
Chapter 3 Installing the Router Setting Up the Chassis
Figure 3-8 Bracket Installation—Rear Panel Forward (19-Inch Rack with a 17.5-Inch Opening)
Figure 3-9 Bracket Installation—Rear Panel Forward (19-Inch Rack with a 17.75-Inch Opening or a
23- or 24-Inch Rack)
72013
Note: The second bracket attaches
to the other side of the chassis.
Brackets for
19-inch rack
110V 60 Hz
1.6A MAX
72014
Note: The second bracket attaches
to the other side of the chassis.
110V 60 Hz
1.6A MAX
Brackets for
19-inch rack Brackets for
23-inch or 24-inch rack

3-8
Cisco 2600 Series Routers Hardware Installation Guide OL-2171-02
Chapter 3 Installing the Router
Setting Up the Chassis
Figure 3-10 Center-Mount Bracket Installation—Rear Panel Forward (19-Inch Rack with a 17.75-Inch
Opening or a 23- or 24-Inch Rack)
Figure 3-11 Center-Mount Bracket Installation—Rear Panel Forward (19-Inch Rack with a 17.5-Inch
Opening or a 23- or 24-Inch Rack)
Figure 3-12 Center-Mount Bracket Installation—Front Panel Forward (19-Inch Rack with a 17.5-Inch
Opening or a 23- or 24-Inch Rack)
72015
Note: The second bracket attaches
to the other side of the chassis.
110V 60 Hz
1.6A MAX
Brackets for
19-inch rack Brackets for
23-inch or 24-inch rack
62983
Note: The second bracket attaches
to the other side of the chassis.
Brackets for
19-inch rack Brackets for 23-inch or 24-inch rack
110V 60 Hz
1.6A MAX
72016
Note: The second bracket attaches
to the other side of the chassis.
Brackets for
19-inch rack Brackets for 23-inch or 24-inch rack

3-9
Cisco 2600 Series Routers Hardware Installation Guide
OL-2171-02
Chapter 3 Installing the Router Setting Up the Chassis
Attaching the Brackets to a Cisco 2691 Router
To install the chassis in a rack, attach the brackets in one of the following ways:
•With the front panel forward (see Figure 3-13.)
•With the rear panel forward (see Figure 3-14.)
•In a center-mount rack (see Figure 3-15 and Figure 3-16.)
Note Use the screws that came with your router package for attaching the brackets.
Figure 3-13 Bracket Installation—Front Panel Forward (19-Inch Rack)
Figure 3-14 Bracket Installation—Rear Panel Forward (19-Inch Rack)
LEFT
Wide bracket
(marked RIGHT)
62103
Narrow bracket
(marked LEFT)
RIGHT
SERIES
SERIES
RIGHT
Wide bracket
(marked RIGHT)
62109
SEE MANUAL BEFORE INSTALLATION
Narrow bracket
(marked LEFT)
AL
CD
LP
RD
TD
SEE MANUAL BEFORE INSTALLATION
DSU
56K
AL
CD
LP
RD
TD
SEE MANUAL BEFORE INSTALLATION
DSU
56K
LEFT
EN
V0
BANK 4 BANK 3 BANK 2 BANK 1 BANK 0
NM-HDV
VWIC
2MFT-E1
SEE
MANUAL
BEFORE
INSTALLATION
CTRLR E2 CTRLR E1
AL
LP
CD

3-10
Cisco 2600 Series Routers Hardware Installation Guide OL-2171-02
Chapter 3 Installing the Router
Setting Up the Chassis
Figure 3-15 Center-Mount Bracket Installation—Front Panel Forward (19-Inch Rack)
Figure 3-16 Center-Mount Bracket Installation—Rear Panel Forward (19-Inch Rack)
Installing the Router in a Rack
After the brackets are secured to the chassis, you can mount the chassis in a rack. Use the illustrations
in the previous section as a guide to attaching the brackets to the rack.
Note The screws for attaching the brackets to the rack are not included with the router.
Caution Always use two screws to attach each bracket to the rack.
Mounting the Chassis on the Wall
Cisco 2600 series routers with a chassis height of 1RU can be attached to a wall. Mounting a 2RU chassis
to a wall is not recommended and brackets are not provided for mounting to a wall.
LEFT
Wide bracket
(marked RIGHT)
62677
RIGHT
SERIES
SERIES
Narrow bracket
(marked LEFT)
RIGHT
Wide bracket
(marked RIGHT)
62108
SEE MANUALBEFORE INSTALLATION
Narrow bracket
(marked LEFT)
AL
CD
LP
RD
TD
SEE MANUALBEFORE INSTALLATION
DSU
56K
AL
CD
LP
RD
TD
SEE MANUALBEFORE INSTALLATION
DSU
56K
LEFT
EN
V0
BANK 4 BANK 3 BANK 2 BANK 1 BANK 0
NM-HDV
VWIC
2MFT-E1
SEE
MANUAL
BEFORE
INSTALLATION
CTRLR E2 CTRLR E1
AL
LP
CD