Cisco 7600 Series User manual

CHAPTER
2-1
Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-14
2
Overview: Cisco 7600 Series SIPs
This chapter describes the SPA interface processors (SIPs) that are supported on the Cisco 7600 series
routers and contains the following sections:
•SIP Summary, page 2-1
•Identifying Slots and Subslots for SIPs and SPAs, page 2-2
•Cisco 7600 SIP-200 Overview, page 2-5
•Cisco 7600 SIP-400 Overview, page 2-8
•Cisco 7600 SIP-600 Overview, page 2-10
•Cisco 7600 SSC-400 Overview, page 2-12
SIP Summary
Summary descriptions of the SIPs that are supported on the Cisco 7600 series routers are shown in
Table 2-1.
Note The Description column indicates the aggregate bandwidth supported by the SIP across all subslots—not
per SPA subslot.
Table 2-1 SIP Summary
SIP Product Number Description
Maximum
Number of
SPAs
Minimum Cisco
IOS Release
Cisco 7600 SIP-200 7600-SIP-200 622-Mbps SPA interface
processor
4 12.2(18)SXE
Cisco 7600 SIP-400 7600-SIP-400 2.5-Gbps SPA interface
processor
4 12.2(18)SXE
Cisco 7600 SIP-600 7600-SIP-600 1 x 10-Gbps SPA Interface
Processor
1 12.2(18)SXF
Cisco 7600 SSC-400 7600-SSC-400 SPA services carrier 2 12.2(18)SXE2

2-2
Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-14
Chapter 2 Overview: Cisco 7600 Series SIPs
Identifying Slots and Subslots for SIPs and SPAs
Checking Hardware and Software Compatibility
To check the minimum software requirements of Cisco IOS software with the hardware installed on your
router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether SIPs
or SPAs within a system are compatible, but it does provide the minimum Cisco IOS requirements for
individual hardware modules or components.
Note Access to this tool is limited to users with Cisco.com login accounts.
To access Software Advisor, click Login at Cisco.com, type “Software Advisor” in the SEARCH box,
and click GO. Click the link for the Software Advisor tool.
Choose a product family or enter a specific product number to search for the minimum supported
software release needed for your hardware.
Identifying Slots and Subslots for SIPs and SPAs
This section describes how to specify the physical locations of a SIP and SPA on the Cisco 7600 series
routers within the command-line interface (CLI) to configure or monitor those devices.
Note For simplicity, any reference to “SIP” in this section also applies to the SSC.
Specifying the Slot Location for a SIP or SSC
The Cisco 7600 series router supports different chassis models, each of which supports a certain number
of chassis slots.
Note The Cisco 7600 series router SIPs are not supported with a Supervisor Engine 1, Supervisor Engine 1A,
Supervisor Engine 2, or Supervisor Engine 720-3A.

2-3
Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-14
Chapter 2 Overview: Cisco 7600 Series SIPs
Identifying Slots and Subslots for SIPs and SPAs
Figure 2-1 shows an example of a SIP installed in slot 6 on a Cisco 7609 router. The Cisco 7609 router
has nine vertically-oriented chassis slots, which are numbered 1 to 9 from right to left.
Figure 2-1 SIP and SPA Installed in a Cisco 7609 Router
Figure 2-2 shows an example of a SIP installed in slot 6 on a Catalyst 6509 switch. The Catalyst 6509
switch has nine horizontally-oriented chassis slots, which are numbered 1 to 9 from right to left.
Figure 2-2 SIP and SPA Installed in a Catalyst 6509 Switch
129006
INPUT
OK
FAN
OK
OUTPUT
FAIL
o
INPUT
OK
FAN
OK
OUTPUT
FAIL
o
SUPERVISOR2
WS-X6K-SUP2-2GE
STATUS
SYSTEM
CONSOLE
PWRMGMT
RESET
CONSOLE
CONSOLE
PORT
MODE
PCMCIAEJECT
PORT1PORT2
SwitchLoad
100%
1%
LINK
LINK
SUPERVISOR2
WS-X6K-SUP2-2GE
STATUS
SYSTEM
CONSOLE
PWRMGMT
RESET
CONSOLE
CONSOLE
PORT
MODE
PCMCIA EJECT
PORT1 PORT2
SwitchLoad
100%
1%
LINK
LINK
SWITCHFABRIC MDL
STATUS
SELECT
NEXT
WS-C6500-SFM
ACTIVE
OC12POSMM
OSM-40C12-POS-MM
STATUS
1
2
3
4
RESET
LINK
1
LINK
2
LINK
3
LINK
4
CARRIER
ALARM
ACTIVE
TX
RX
TX
PORT1
RX
CARRIER
ALARM
ACTIVE
TX
RX
TX
PORT2
RX
CARRIER
ALARM
ACTIVE
TX
RX
TX
PORT3
RX
CARRIER
ALARM
ACTIVE
TX
RX
TX
RX
OC12POSMM
OSM-40C12-POS-MM
STATUS
1
2
3
4
RESET
LINK
1
LINK
2
LINK
3
LINK
4
CARRIER
ALARM
ACTIVE
TX
RX
TX
PORT1
RX
CARRIER
ALARM
ACTIVE
TX
RX
TX
PORT2
RX
CARRIER
ALARM
ACTIVE
TX
RX
TX
PORT3
RX
CARRIER
ALARM
ACTIVE
TX
RX
TX
RX
OC12POSMM
OSM-40C12-POS-MM
STATUS
1
2
3
4
RESET
LINK
1
LINK
2
LINK
3
LINK
4
CARRIER
ALARM
ACTIVE
TX
RX
TX
PORT1
RX
CARRIER
ALARM
ACTIVE
TX
RX
TX
PORT2
RX
CARRIER
ALARM
ACTIVE
TX
RX
TX
PORT3
RX
CARRIER
ALARM
ACTIVE
TX
RX
TX
RX
8PORT OC3 POS MM
OSM-8OC3-POSMM
STATUS
1
1
2
2
3
3
1
2
3
4
4
4
RESET
LINK
CARRIER
ALARM
LINK
LINK
LINK
LINK
5
6
7
8
8PORT OC3 POS MM
OSM-8OC3-POSMM
STATUS
1
1
2
2
3
3
1
2
3
4
4
4
RESET
LINK
CARRIER
ALARM
LINK
LINK
LINK
LINK
5
6
7
8
STATUS
2
0
3
1
SPAINTERFACE
PROCESSOR
7600-SIP-200
LINK
CARRIER
ALARM
LINK
5
POWER SUPPLY 1 POWER SUPPLY 2
3 1
4 2
SP
A-4XT3/E3
TX
RX
A/L
0
C/A
TX
RX
A/L
1
C/A
TX
RX
A/L
2
C/A
TX
RX
A/L
3
STATUS
C/A

2-4
Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-14
Chapter 2 Overview: Cisco 7600 Series SIPs
Identifying Slots and Subslots for SIPs and SPAs
Some commands allow you to display information about the SIP itself, such as show module,show
sip-disk, show idprom module, show hw-module slot, and show diagbus. These commands require
you to specify the chassis slot location where the SIP that you want information about is installed.
For example, to display status and information about the SIP installed in slot 6 as shown in Figure 2-1,
enter the following command:
Router# show module 6
For more information about SIP commands, refer to the Cisco IOS Software Releases 12.2SR Command
References and to the Cisco IOS Software Releases 12.2SX Command References.
Specifying the SIP or SSC Subslot Location for a SPA
SIP subslots begin their numbering with “0” and have a horizontal or vertical orientation depending on
the orientation of the SIP in the router chassis slot, as shown in the “SIP, SSC, and SPA Product
Overview” chapter of the Cisco 7600 Series Router SIP, SSC, and SPA Software Configuration Guide.
1SIP subslot 0 4SIP subslot 3
2SIP subslot 1 5Chassis slots 1–9 (numbered from right to left)
(numbered from top to bottom)
3SIP subslot 2
138980
FAN
STATUS
INPUT
OK
FAN
OK
OUTPUT
FAI L
o
INPUT
OK
FAN
OK
OUTPUT
FAI L
o
1
2
3
4
5
6
7
8
9
STATUS
2
0
3
1
SP
AINTERFA CE
PROCESSOR
7600-SIP-200
SPA-4XT3/E3
TX
RX
A/L
0
C/A
TX
RX
A/L
1
C/A
TX
RX
A/L
2
C/A
TX
RX
A/L
3
STATUS
C/A
8 PORT GIGABIT ETHERNET
WS-X6408
1
LINK
STATUS
2345678
LINK
LINK
LINK
LINK
LINK
LINK
LINK
8PORT GIGABIT ETHERNET
WS-X6408
1
LINK
STATUS
2345678
LINK
LINK
LINK
LINK
LINK
LINK
LINK
8 PORT GIGABIT ETHERNET
WS-X6408
1
LINK
STATUS
2345678
LINK
LINK
LINK
LINK
LINK
LINK
LINK
24 PORT100FX
WS-X6224
STATUS
24PORT100FX
WS-X6224
STATUS
24PORT100FX
WS-X6224
STATUS
1
LINK
2
LINK
3
LINK
4
LINK
5
LINK
6
LINK
7
LINK
8
LINK
9
LINK
10
LINK
11
LINK
12
LINK
13
LINK
14
LINK
15
LINK
16
LINK
17
LINK
18
LINK
19
LINK
20
LINK
21
LINK
22
LINK
23
LINK
24
LINK
1
LINK
2
LINK
3
LINK
4
LINK
5
LINK
6
LINK
7
LINK
8
LINK
9
LINK
10
LINK
11
LINK
12
LINK
13
LINK
14
LINK
15
LINK
16
LINK
17
LINK
18
LINK
19
LINK
20
LINK
21
LINK
22
LINK
23
LINK
24
LINK
1
LINK
2
LINK
3
LINK
4
LINK
5
LINK
6
LINK
7
LINK
8
LINK
9
LINK
10
LINK
11
LINK
12
LINK
13
LINK
14
LINK
15
LINK
16
LINK
17
LINK
18
LINK
19
LINK
20
LINK
21
LINK
22
LINK
23
LINK
24
LINK
SUPERVISOR2
WS-X6K-SUP2-2GE
STATUS
SYSTEM
CONSOLE
PWRMGMT
RESET
CONSOLE
CONSOLE
PORT
MODE
PCMCIA EJECT
PORT1 PORT2
SwitchLoad
100%
1%
LINK
LINK
SUPERVISOR2
WS-X6K-SUP2-2GE
STATUS
SYSTEM
CONSOLE
PWRMGMT
RESET
CONSOLE
CONSOLE
PORT
MODE
PCMCIA EJECT
PORT1 PORT2
SwitchLoad
100%
1%
LINK
LINK
1
34
5
2

2-5
Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-14
Chapter 2 Overview: Cisco 7600 Series SIPs
Cisco 7600 SIP-200 Overview
Figure 2-1 shows an example of a Cisco 7600 SIP-200 installed with a vertical orientation on a
Cisco 7609 router. The Cisco 7600 SIP-200 supports four subslots for the installation of SPAs. In this
example, the subslot locations are vertically oriented as follows:
•SIP subslot 0—Top–right subslot
•SIP subslot 1—Bottom–right subslot
•SIP subslot 2—Top–left subslot
•SIP subslot 3—Bottom–left subslot
Figure 2-3 shows the faceplate for the Cisco 7600 SIP-200 in a horizontal orientation.
Figure 2-3 Cisco 7600 SIP-200 Faceplate
In this view, the subslot locations in a horizontal orientation are as follows:
•SIP subslot 0—Top–left subslot
•SIP subslot 1—Top–right subslot
•SIP subslot 2—Bottom–left subslot
•SIP subslot 3—Bottom–right subslot
The SIP subslot numbering is indicated by a small numeric label beside the subslot on the faceplate.
Just as with the SIPs, some commands allow you to display information about the SPA itself, such as
show idprom module and show hw-module subslot. These commands require you to specify both the
physical location of the SIP and SPA in the format, slot/subslot, where:
•slot—Specifies the chassis slot number in the Cisco 7600 series router where the SIP is installed.
•subslot—Specifies the secondary slot of the SIP where the SPA is installed.
For example, to display the operational status for the SPA installed in the first subslot of the SIP in
chassis slot 6 shown in Figure 2-1, enter the following command:
Router# show hw-module subslot 6/0 oir
For more information about SIP commands, refer to the Cisco IOS Software Releases 12.2SR Command
References and to the Cisco IOS Software Releases 12.2SX Command References.
Cisco 7600 SIP-200 Overview
The following sections describe the Cisco 7600 SIP-200 (Cisco part number 7600-SIP-200):
•Cisco 7600 SIP-200 Processor, page 2-6
•Cisco 7600 SIP-200 LEDs, page 2-6
•Cisco 7600 SIP-200 Physical Specifications, page 2-6
•Cisco 7600 SIP-200 Memory Options, page 2-7
•Cisco 7600 SIP-200 Default DIP Switch Settings, page 2-8
STATUS
2
0
3
1
SPA INTERFACE
PROCESSOR
7600-SIP-200
116849

2-6
Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-14
Chapter 2 Overview: Cisco 7600 Series SIPs
Cisco 7600 SIP-200 Overview
Cisco 7600 SIP-200 Processor
The processor on a Cisco 7600 SIP-200 is described in Table 2-2.
Cisco 7600 SIP-200 LEDs
The Cisco 7600 SIP-200 has one LED, as shown in Figure 2-4.
Figure 2-4 Cisco 7600 SIP-200 Faceplate
The Cisco 7600 SIP-200 LED is described in Table 2-3.
Cisco 7600 SIP-200 Physical Specifications
The Cisco 7600 SIP-200 physical specifications are shown in Table 2-4.
Table 2-2 Cisco 7600 SIP-200 Processor
Type Speed Description
CPU 800 megahertz (MHz) internal operating
frequency
Broadcom 1125 MIPS-based design
STATUS
2
0
3
1
SPA INTERFACE
PROCESSOR
7600-SIP-200
116849
Table 2-3 Cisco 7600 SIP-200 LED
LED Label Color State Meaning
STATUS Red On The SIP has encountered an error.
Green On The SIP is online.
Yellow On The SIP is loading.
Off Off The SIP is powered off.
Table 2-4 Cisco 7600 SIP-200 Physical Specifications
Description Specifications
Physical dimensions The SIP occupies one module slot and can be operated in Cisco 7600
series routers.
Shipping weight 8 lb (3.64 kg)
Operating temperature 32 to 104°F (0 to 40°C)
Relative humidity 10 to 90 percent, noncondensing
Storage temperature –4 to 149°F (–20 to 65°C)

2-7
Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-14
Chapter 2 Overview: Cisco 7600 Series SIPs
Cisco 7600 SIP-200 Overview
Cisco 7600 SIP-200 Memory Options
The following table lists the memory available for the Cisco 7600 SIP-200:
Note The SIP DIMMs must be a matched set. A warning message appears on the console if the DIMMs on the
SIP are different sizes. If the sizes are not the same, the following message appears at bootup/OIR:
C7600_SIP200-3-MEM_MODULE_MISMATCH: Memory modules are not identical
Cisco 7600 SIP-200 Memory Installation and Removal
Figure 2-5 shows the location of the DIMMs on a Cisco 7600 SIP-200. Perform the following procedure
to install and remove a DIMM:
To install a DIMM, slide the DIMM into the slot. The retaining clips secure the DIMM in place.
Step 1 To remove a DIMM, separate the two retaining clips.
Step 2 Pull the DIMM from the slot.
Figure 2-5 SIP DIMM Location
Table 2-5 SIP Memory Options
SIP Memory Options
Cisco 7600 SIP-200 512 MB and 1 GB (2 x 256-MB or 2 x 512-MB DIMMs)
1DIMMs
STATUS
2
0
MODULAR
SERVICES CARD
7600-MSC-200
122390
1

2-8
Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-14
Chapter 2 Overview: Cisco 7600 Series SIPs
Cisco 7600 SIP-400 Overview
Cisco 7600 SIP-200 Default DIP Switch Settings
If SW3 and SW10 switches are present on the board, make sure they are set to the default settings, as
shown in Table 2-6. See Figure 2-6 for the location of the switches.
The switches are set to their defaults during manufacture. However, the switch settings may get
inadvertently changed during handling.
Note If the switches are not set to their default settings, there may be momentary packet drops during OIR of
the board.
Table 2-6 Cisco 7600 SIP-200 Default DIP Settings
Figure 2-6 Cisco 7600 SIP-200 DIP Switch Locations
\
Cisco 7600 SIP-400 Overview
The following sections describe the Cisco 7600 SIP-400 (Cisco part number 7600-SIP-400):
•Cisco 7600 SIP-400 Processor, page 2-9
•Cisco 7600 SIP-400 LEDs, page 2-9
•Cisco 7600 SIP-400 Physical Specifications, page 2-9
Switch Default Position
SW3 Up
SW10 Down
1SW3 2SW10
STATUS
2
0
MODULAR
SERVICES CARD
7600-MSC-200
129724
1
2

2-9
Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-14
Chapter 2 Overview: Cisco 7600 Series SIPs
Cisco 7600 SIP-400 Overview
Cisco 7600 SIP-400 Processor
The processor on a Cisco 7600 SIP-400 is described in Table 2-7.
Cisco 7600 SIP-400 LEDs
The Cisco 7600 SIP-400 has one LED, as shown in Figure 2-7.
Figure 2-7 Cisco 7600 SIP-400 Faceplate
The Cisco 7600 SIP-400 LED is described in Table 2-8.
Cisco 7600 SIP-400 Physical Specifications
The Cisco 7600 SIP-400 physical specifications are shown in Table 2-9.
Table 2-7 7600-SIP-400 Processor
Type Speed Description
CPU 400 megahertz (MHz) internal operating
frequency
Broadcom 1125 MIPS-based design
STATUS
2
0
3
1
SPA INTERFACE
PROCESSOR
7600-SIP-400
101313
Table 2-8 Cisco 7600 SIP-400 LED
LED Label Color State Meaning
STATUS Red On The SIP has encountered an error.
Green On The SIP is online.
Yellow On The SIP is loading.
Off Off The SIP is powered off.
Table 2-9 Cisco 7600 SIP-400 Physical Specifications
Description Specifications
Physical dimensions The SIP occupies one module slot and can be operated in Cisco 7600
series routers.
Shipping weight 8 lb (3.64 kg)
Operating temperature 32 to 104°F (0 to 40°C)
Relative humidity 10 to 90 percent, noncondensing
Storage temperature –4 to 149°F (–20 to 65°C)

2-10
Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-14
Chapter 2 Overview: Cisco 7600 Series SIPs
Cisco 7600 SIP-600 Overview
Cisco 7600 SIP-600 Overview
The following sections describe the Cisco 7600 SIP-600 (Cisco part number 7600-SIP-600):
•Cisco 7600 SIP-600 Processor, page 2-10
•Cisco 7600 SIP-600 LEDs, page 2-10
•Cisco 7600 SIP-600 Physical Specifications, page 2-10
Cisco 7600 SIP-600 Processor
The processor on a Cisco 7600 SIP-600 is described in Table 2-10.
Cisco 7600 SIP-600 LEDs
The Cisco 7600 SIP-600 has one LED, as shown in Figure 2-8.
Figure 2-8 Cisco 7600 SIP-600 Faceplate
The Cisco 7600 SIP-600 LED is described in Table 2-11.
Cisco 7600 SIP-600 Physical Specifications
The Cisco 7600 SIP-600 physical specifications are shown in Table 2-12.
Table 2-10 Cisco 7600 SIP-600 Processor
Type Speed Description
CPU 400 megahertz (MHz) internal operating
frequency
Broadcom 1125 MIPS-based design
STATUS
2
0
3
1
SPA INTERFACE
PROCESSOR
7600-SIP-600
138127
Table 2-11 Cisco 7600 SIP-600 LED
LED Label Color State Meaning
STATUS Red On The SIP has encountered an error.
Green On The SIP is online.
Yellow On The SIP is loading.
— Off The SIP is powered off.