Cisco ASR 1004 Installation guide

Cisco ASR 1004 Router Overview and Installation
This chapter describes the Cisco ASR 1004 Router and the procedures for installing the Cisco ASR 1004
Router on an equipment shelf or tabletop or in equipment racks. It also describes how to connect interface
and power cables.
This chapter contains the following sections:
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents. Use the statement number provided at the end of each warning
to locate its translation in the translated safety warnings that accompanied this device. Statement 1071
Warning
Before you install, operate, or service the system, read the Regulatory Compliance and Safety Information
for Cisco ASR 1000 Series Aggregation Services Routers publication. This document provides important
safety information you should know before working with the system. Statement 200
Warning
•Cisco ASR 1004 Router Description, page 2
•Installation Methods, page 6
•General Rack Installation Guidelines, page 6
•Guidelines for an Equipment Shelf or Tabletop Installation, page 7
•Equipment Shelf or Tabletop Installation, page 8
•Rack-Mounting the Cisco ASR 1004 Router, page 10
•Attaching the Chassis Rack-Mount Brackets, page 12
•Installing the Cisco ASR 1004 Router in a Rack, page 15
•Attaching a Chassis Ground Connection, page 21
•Attaching the Cable-Management Bracket, page 24
•Connecting the Shared Port Adapter Cables, page 25
•Connecting the Console and Auxiliary Port Cables, page 26
Cisco ASR 1000 Series Router Hardware Installation Guide
1

•Connecting Power to Cisco ASR 1004 Router, page 28
•Connecting a Terminal to the Cisco ASR Series 1000 Route Processor Console Port, page 35
•Connecting the Network Management and Signal System Cables, page 38
Cisco ASR 1004 Router Description
The Cisco ASR 1004 Router system consists of the following system level components:
•Two Cisco ASR 1000 Series SPA Interface Processor (Cisco ASR1000-SIP10 or Cisco ASR1000-SIP40)
•One Cisco ASR 1000 Series Embedded Services Processor (Cisco ASR 1000-ESP10, Cisco ASR
1000-ESP20, or Cisco ASR1000-ESP40)
•One Cisco ASR 1000 Series Route Processor (Cisco ASR1000-RP1 or Cisco ASR1000-RP2)
•Dual (redundant) AC and DC power supplies
This section contains the following topics:
Front View
The following image shows the Cisco ASR 1004 Router with modules and filler plates installed.
Figure 1: Cisco ASR 1004 Router — Front and Side View
SPA subslot 25Slot R0 with ASR 1000
Series Route Processor
1
SPA subslot 06Slot F0 with Cisco
ASR1000-ESP10, Cisco
ASR1000-ESP20, or
Cisco ASR1000-ESP40
2
Cisco ASR 1000 Series Router Hardware Installation Guide
2
Cisco ASR 1004 Router Overview and Installation
Cisco ASR 1004 Router Description

SPA subslot 17ASR 1000 Series SIP slot
0
3
SPA subslot 38ASR 1000 Series SIP slot
1
4
Rear View
The following image shows the rear of the Cisco ASR 1004 Router with two AC power supplies installed.
Figure 2: Cisco ASR 1004 Router Rear View with AC Power Supplies
AC power supply fan4AC power supply
Standby switch
1
AC power inlet5AC power supply LEDs2
AC power supply handle6AC power supply DB-25
alarm connector
3
Cisco ASR 1000 Series Router Hardware Installation Guide
3
Cisco ASR 1004 Router Overview and Installation
Rear View

The following image shows the rear of the Cisco ASR 1004 Router with two –48 VDC power supplies installed.
Figure 3: Cisco ASR 1004 Router Rear View With – 48 VDC Power Supplies
Grounding symbol5
–48 VDC power supply
terminal block
1
–48 VDC power supply
On/Off switch
6
–48 VDC power supply
LEDs
2
–48 VDC power supply
handle
7
–48 VDC power supply
DB-25 alarm connector
3
——–48 VDC power supply
fan
4
Internal fans draw cooling air into the chassis and across internal components to maintain an acceptable
operating temperature. (See Figure 2: Cisco ASR 1004 Router Rear View with AC Power Supplies, on page
3.) The fans are located at the rear of the chassis. A two-hole grounding lug is located on the side of the
chassis. Two power supplies, either two AC power supplies or two –48 VDC power supplies, are accessed
from the rear of the router.
You have already unpacked your chassis and read all the site requirements for your new equipment.
Proceed with the installation.
Note
Do not combine AC and –48 VDC power supplies in the same chassis.
Note
Cisco ASR 1000 Series Router Hardware Installation Guide
4
Cisco ASR 1004 Router Overview and Installation
Rear View

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents. Use the statement number provided at the end of each warning
to locate its translation in the translated safety warnings that accompanied this device. Statement 1071
Warning
Before you install, operate, or service the system, read the Regulatory Compliance and Safety Information
for Cisco ASR 1000 Series Aggregation Services Routers publication. This document provides important
safety information you should know before working with the system. Statement 200
Warning
You have already unpacked your chassis and read all the site requirements for your new equipment.
Proceed with the installation.
Note
Cisco ASR 1004 Router Slot Numbering
The Cisco ASR 1004 Router contains two Cisco ASR 1000 Series SPA Interface Processors (SIPs) and
supports four subslots for the installation of SPAs.
The following image shows the Cisco ASR 1004 Router with modules and filler plates installed.
Figure 4: Cisco ASR 1004 Router — Front and Side View
SPA subslot 25Slot R0 with ASR 1000
Series RP1
1
SPA subslot 06Slot F0 with Cisco
ASR1000-ESP10, Cisco
ASR1000-ESP20, or
Cisco ASR1000-ESP40
2
Cisco ASR 1000 Series Router Hardware Installation Guide
5
Cisco ASR 1004 Router Overview and Installation
Rear View

SPA subslot 17ASR 1000 Series SIP slot
0
3
SPA subslot 38ASR 1000 Series SIP slot
1
4
Installation Methods
Although rack-mounting is the preferred method of installation for the Cisco ASR 1004 Router, you can
mount the chassis:
•On an equipment shelf or tabletop
•In a19-inch wide (standard), 4-post equipment rack or two-post, using the rack-mount brackets in the
accessory kit
The Cisco ASR 1004 Router usually ships fully loaded. However, you can remove components from the
chassis to make the chassis lighter for your rack installation.
Note
General Rack Installation Guidelines
When planning your rack installation, consider the following guidelines:
•The Cisco ASR 1004 Router requires a minimum of 4 rack units (7 inches or 17.8 cm) of vertical rack
space. Measure the proposed rack location before mounting the chassis in the rack.
•Before using a particular rack, check for obstructions (such as a power strip) that could impair rack-mount
installation. If a power strip does impair a rack-mount installation, remove the power strip before installing
the chassis, and then replace it after the chassis is installed.
•Allow sufficient clearance around the rack for maintenance. If the rack is mobile, you can push it back
near a wall or cabinet for normal operation and pull it out for maintenance (installing or moving cards,
connecting cables, or replacing or upgrading components). Otherwise, allow 19 inches (48.3 cm) of
clearance to remove field-replaceable units.
•Maintain a minimum clearance of 3 inches (7.62 cm) on the front, top, and sides of the chassis for the
cooling air inlet and exhaust ports, respectively. Avoid placing the chassis in an overly congested rack
or directly next to another equipment rack; otherwise, the heated exhaust air from other equipment can
enter the inlet air vents and cause an overtemperature condition inside the router.
To prevent chassis overheating, never install a Cisco ASR 1004 Router in an enclosed room that is not
properly ventilated or air conditioned.
Caution
Cisco ASR 1000 Series Router Hardware Installation Guide
6
Cisco ASR 1004 Router Overview and Installation
Installation Methods

•Always install heavier equipment in the lower half of a rack to maintain a low center of gravity to prevent
the rack from falling over.
•Install and use the cable-management brackets included with the Cisco ASR 1004 Router to keep cables
organized and out of the way of the cards and processors. Ensure that cables from other equipment
already installed in the rack do not impair access to the cards or require you to disconnect cables
unnecessarily to perform equipment maintenance or upgrades.
•Install rack stabilizers (if available) before you mount the chassis.
•Provide an adequate chassis ground (earth) connection for your router chassis.
In addition to the preceding guidelines, review the precautions for avoiding excessive temperature conditions
in the “Site Environmental Requirements”section on page 5-9 .
The following table provides the Cisco ASR 1004 Router dimensions and weight information.
Table 1: Cisco ASR 1004 Router Dimensions and Weight
DimensionsCisco ASR 1004
22.50 in. (57.15 cm)(including card handles,
cable-management brackets, power supply handles).
Depth
6.95 in. (17.653cm) (4 rack-mount per EIA RS-310)Height
17.25 in. (43.815 cm) (19 inch rack- mount or
optional 23 Telco rack-mount)
Width
50 pounds (fully configured)
22.6796 kg
Weight
Guidelines for an Equipment Shelf or Tabletop Installation
The chassis should already be in the area where you will install it. If you have not determined where to install
your chassis, see the “Cisco ASR 1000 Series Routers Component Overview”section on page 2-1 for
information about site considerations.
If you are not rack-mounting your Cisco ASR 1000 series chassis, place it on a sturdy equipment shelf or
tabletop.
When installing the Cisco ASR 1004 Router on an equipment shelf or tabletop, ensure that the surface is clean
and that you have considered the following:
•The Cisco ASR 1004 Router requires at least 3 inches (7.62 cm) of clearance at the inlet and exhaust
vents (the front and top/rear sides of the chassis).
•The Cisco ASR 1004 Router should be installed off the floor. Dust that accumulates on the floor is drawn
into the interior of the router by the cooling fans. Excessive dust inside the router can cause
overtemperature conditions and component failures.
•There must be approximately 19 inches (48.3 cm) of clearance at the front and rear of the chassis to
install and replace FRUs, or to access network cables and equipment.
Cisco ASR 1000 Series Router Hardware Installation Guide
7
Cisco ASR 1004 Router Overview and Installation
Guidelines for an Equipment Shelf or Tabletop Installation

•The Cisco ASR 1004 Router needs adequate ventilation. Do not install it in an enclosed cabinet where
ventilation is inadequate.
•Have the cable-management bracket available if you plan to install it on the front of the chassis.
•An adequate chassis ground (earth) connection exists for your router chassis (see the Attaching a Chassis
Ground Connection, on page 21).
•Always follow proper lifting practices as outlined in the “Electrical Safety”section on page 5-21 , when
handling the chassis.
Equipment Shelf or Tabletop Installation
At least two people are required to lift the chassis onto a tabletop or platform. To prevent injury, keep
your back straight and lift with your legs, not your back. Statement 164
Note
Figure 5: Lifting the Chassis
The chassis in the image does not represent the Cisco ASR 1004 Router. This is only an example of how
to lift a Cisco chassis.
Note
Cisco ASR 1000 Series Router Hardware Installation Guide
8
Cisco ASR 1004 Router Overview and Installation
Equipment Shelf or Tabletop Installation

SUMMARY STEPS
1. Attach the front rack-mount brackets. Locate the threaded holes in the front sides of the chassis (first holes
beyond the vent holes) and use the package of black screws that shipped with the chassis.
2. Align the front rack-mount bracket to one side of the chassis.
3. Insert and tighten the screws on one side.
4. Repeat Step 2 through Step 3 on the other side of the chassis. Use all the screws to secure the rack-mount
brackets to the chassis.
5. Gather the two cable-management brackets and screws shipped with your chassis. The followng image
shows attached cable-management brackets on the front of the Cisco ASR 1004 Router.
6. Screw the cable-management bracket to each side of the rack-mount brackets already attached to the
chassis. Use two screws for each cable-management bracket. Use the package of four screws.
7. Check that all screws are securely tightened.
DETAILED STEPS
Step 1 Attach the front rack-mount brackets. Locate the threaded holes in the front sides of the chassis (first holes beyond the
vent holes) and use the package of black screws that shipped with the chassis.
Step 2 Align the front rack-mount bracket to one side of the chassis.
Step 3 Insert and tighten the screws on one side.
Step 4 Repeat Step 2 through Step 3 on the other side of the chassis. Use all the screws to secure the rack-mount brackets to
the chassis.
The cable-management brackets are installed on the chassis after you install the chassis rack-mount brackets
and mount the chassis in the rack.
Note
Step 5 Gather the two cable-management brackets and screws shipped with your chassis. The followng image shows attached
cable-management brackets on the front of the Cisco ASR 1004 Router.
Cisco ASR 1000 Series Router Hardware Installation Guide
9
Cisco ASR 1004 Router Overview and Installation
Equipment Shelf or Tabletop Installation

Make certain that the cable-management ‘U’feature device has the open end pointing upwards when you attach
it to the chassis after the chassis is installed in a rack.
Note
Figure 6: Attaching the Cable-Management Brackets to the Cisco ASR 1004 Router
Chassis front rack-mount
bracket ear
3Cable-management bracket
screws
1
——
Cable-management bracket2
Step 6 Screw the cable-management bracket to each side of the rack-mount brackets already attached to the chassis. Use two
screws for each cable-management bracket. Use the package of four screws.
Step 7 Check that all screws are securely tightened.
What to Do Next
You have completed a tabletop or equipment shelf chassis installation. Go to the Attaching a Chassis Ground
Connection, on page 21 to continue the installation.
Rack-Mounting the Cisco ASR 1004 Router
The Cisco ASR 1004 Router can be installed with both front or rear rack-mount brackets.
Cisco ASR 1000 Series Router Hardware Installation Guide
10
Cisco ASR 1004 Router Overview and Installation
Rack-Mounting the Cisco ASR 1004 Router