Cisco ASR 1001-X Manual

Cisco ASR 1001-X Router Hardware Installation Guide
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

©2017 Cisco Systems, Inc. All rights reserved.

CONTENTS
CHAPTER 1 Cisco ASR 1001-X Router Overview 1
Hardware Features of the Cisco ASR 1001-X Router 1
Cisco ASR 1001-X Overall Chassis Front View 2
Cisco ASR 1001-X Router LEDs 3
Cisco ASR 1001-X Management Storage Connections 5
Cisco ASR 1001-X Chassis Rear View 5
Cisco ASR 1001-X SPA GE and TE Ports 6
Field-Replaceable Units for the Cisco ASR 1001-X Router 6
Cisco Product Identification Standard 7
Unique Device Identifier 7
SPA Slot Numbering 9
Serial Number and PID/VID Label Location 9
CHAPTER 2 Cisco ASR 1001-X Router Supported Hardware Components 11
Supported Hardware Components 11
Supported Half-Height SPAs 12
Supported Small Form-Factor Pluggable (SFP and SFP+) Transceivers 14
Supported NIMs 15
NIM-SSD 16
NIM-T1/E1 16
Cisco ASR 1001-X Router Power Supplies 17
Power Supplies for the Cisco ASR 1001-X Router 17
Cisco ASR 1001-X Power Supply Fans 18
Cisco ASR 1001-X Router AC Power Supply 18
Cisco ASR 1001-X Router DC Power Supply 18
AC/DC Power System Input Range and Voltage for the Cisco ASR 1001-X Router 19
Power Cords Supported by the Cisco ASR 1001-X Router 20
Cisco ASR 1001-X Router Hardware Installation Guide
iii

CHAPTER 3 Preparing Your Site for Installation 23
Prerequisites and Preparation 23
Site Planning Checklist 24
Safety Guidelines 24
Safety Warnings 25
Safety Recommendations 25
Compliance Requirements 25
Cautions and Regulatory Compliance Statements for NEBS 26
Standard Warning Statements 27
General Safety Warnings 28
Site Planning 31
General Precautions 31
Site Selection Guidelines 31
Site Environmental Requirements 31
Physical Characteristics 32
Site Power Guidelines 33
Electrical Circuit Requirements 34
Site Cabling Guidelines 35
Console Port Connections 35
USB Serial Console 36
Interference Considerations 36
Electromagnetic Interference 36
Radio Frequency Interference 37
Lightning and AC Power Fault Interference 37
Rack-Mounting Guidelines 37
Precautions for Rack-Mounting 38
General Rack-Selection Guidelines 38
Guidelines for 23-in. (Telco) Racks 39
Equipment Rack Guidelines 39
Locating for Safety 39
Locating for Easy Maintenance 39
Locating for Proper Airflow 40
Preventing Electrostatic Discharge Damage 40
Electrical Safety 41
Cisco ASR 1001-X Router Hardware Installation Guide
iv
Contents

Chassis-Lifting Guidelines 41
Tools and Equipment 42
Unpacking and Verifying Shipping Contents 42
Checking the Shipping Container Contents 43
Cisco ASR 1001-X Router Installation Checklist 44
CHAPTER 4 Cisco ASR 1001-X Router Power Up and Initial Configuration 47
Checking Conditions Prior to System Startup 47
Powering Up the Cisco ASR 1001-X Router 48
Performing the Initial Configuration on the Router 50
Using the Cisco setup Command Facility 50
Completing the Configuration 53
Using the Cisco IOS-XE CLI--Manual Configuration 54
Configuring the Router Hostname 55
Configuring the Enable and Enable Secret Passwords 56
Configuring the Console Idle Privileged EXEC Timeout 57
Examples 58
Gigabit Ethernet Management Interface Overview 58
Default Gigabit Ethernet Configuration 59
Configuring Gigabit Ethernet Interfaces 59
Saving Your Router Configuration 61
Verifying the Initial Configuration 62
Powering Off the Cisco ASR 1001-X Router Safely 62
Environmental Monitoring and Reporting Functions 63
Cisco ASR1001-X Router Alarm Monitoring 63
Environmental Monitoring 64
Fan Failures 65
Reporting Functions 66
CHAPTER 5 Upgrading the ROMMON and CPLD 71
Upgrading the ROMMON 71
Compatibility Requirements 71
Checking the Current ROMMON Version 71
Upgrading the ROMMON for the Cisco ASR 1001-X Router 72
Example: Upgrading a ROMMON 73
Cisco ASR 1001-X Router Hardware Installation Guide
v
Contents

Compatible ROMMON Releases 75
Resolved Caveats 75
Hardware the Require a CPLD Upgrade 75
Upgrading the CPLD 76
Checking Hardware and Software Compatibility 77
Using Cisco Feature Navigator 77
CHAPTER 6 Cisco ASR 1001-X Router License Verification 79
Viewing the Cisco IOS License Level 79
Configuring the Throughput Level 80
Viewing License Information 81
Per Port Counted License (10-GE Interfaces) 87
10-GE Interface Evaluation License Features 88
CHAPTER 7 Removing and Replacing FRUs from the Cisco ASR 1001-X Router 91
Removing and Replacing the Cisco ASR 1001-X Router Power Supplies 91
Removing AC Power Supplies from the Cisco ASR 1001-X Router 92
Installing AC Power Supplies in the Cisco ASR 1001-X Router 94
Removing DC Input Power from the Cisco ASR 1001-X Router 96
Installing DC Input Power on the Cisco ASR 1001-X Router 97
Wiring the DC Input Power Source 98
Removing and Replacing Cisco ASR 1001-X Router USB Flash Memory Stick or Secure
Token 101
Removing and Replacing the Cisco ASR 1001-X Router DIMM 102
Removing and Replacing the Cisco ASR 1001-X Router DIMM Memory Module 102
Removing a Cisco ASR 1001-X Router DIMM 103
Replacing a Cisco ASR 1001-X Router DIMM 105
Removing and Replacing a Cisco ASR 1001-X Router SPA 108
Electrostatic Discharge Prevention 108
Removing a Shared Port Adapter 109
Replacing a Shared Port Adapter 110
Removing and Replacing a NIM on the Cisco ASR 1001-X Router 111
Removing a NIM 112
Replacing a NIM 113
Removing and Replacing an SSD from the NIM-SSD Module 113
Cisco ASR 1001-X Router Hardware Installation Guide
vi
Contents

Removing an SSD from the NIM-SSD Module 114
Installing an SSD into the NIM-SSD Module 116
Repacking the Router 118
CHAPTER 8 Cisco ASR 1001-X Router Specifications 119
Cisco ASR 1006 Router Specifications 119
Cisco ASR 1006 Router Memory and Storage Options 120
Cisco ASR 1006 Router Ethernet RJ-45 Port Pinouts 120
Cisco ASR 1006 Router MGMT Ethernet Port Pinouts 121
Cisco ASR 1006 Router BITS Port Signals and Pinouts 121
Cisco ASR 1006 Router Console Port Signals and Pinouts 122
Cisco ASR 1006 Router Auxiliary Port Signals and Pinouts 123
Cisco ASR 1006 Router DB-25 Pinout Assignments for Alarm Relays 123
Cisco ASR 1004 Router Specifications 124
Cisco ASR 1004 Router Memory and Storage Options 125
Cisco ASR 1004 Router Ethernet RJ-45 Port Pinouts 125
Cisco ASR 1004 Router MGMT Ethernet Port Signals and Pinouts 126
Cisco ASR 1004 Router Console Port Signals and Pinouts 126
Cisco ASR 1004 Router Auxiliary Port Signals and Pinouts 127
Cisco ASR 1004 Router BITS Port Signals and Pinouts 127
Cisco ASR 1004 Router DB-25 Pinout Assignments for Alarm Relays 128
Cisco ASR 1002 Router, Cisco ASR 1002-F Router, and Cisco ASR 1002-X Router
Specifications 128
Cisco ASR 1002 Router Mgmt Ethernet RJ-45 Port Pinouts 129
Cisco ASR 1002 Router Console Port Signals and Pinouts 130
Cisco ASR 1002 Router Auxiliary Port Signals and Pinouts 131
Cisco ASR 1002 Router BITS Port Signals and Pinouts 131
Cisco ASR 1002-X Router BITS Port Signals and Pinouts 132
Cisco ASR 1002-X Router BNC GPS Ports 132
Cisco ASR 1002-X Router Time of Day Port Pinout 133
Cisco ASR 1013 Router Specifications 133
Cisco ASR 1013 Router Memory and Storage Options 135
Cisco ASR 1013 Router Ethernet RJ-45 Port Pinouts 135
Cisco ASR 1013 Router MGMT Ethernet Port Signals and Pinouts 135
Cisco ASR 1013 Router Console Port Signals and Pinouts 136
Cisco ASR 1001-X Router Hardware Installation Guide
vii
Contents

Cisco ASR 1013 Router Auxiliary Port Signals and Pinouts 136
Cisco ASR 1013 Router BITS Port Signals and Pinouts 137
Cisco ASR 1013 Router DB-25 Pinout Assignments for Alarm Relays 137
Cisco ASR 1001-X Router Specifications 138
Cisco ASR 1001-X Router Memory and Storage Options 139
CHAPTER 9 Cisco ASR 1001-X Router Signals and Pinouts 141
Management Ethernet Port Signals and Pinouts 141
Console Port Signals and Pinouts 142
Auxiliary Port Signals and Pinouts 142
Cisco ASR 1001-X Router Hardware Installation Guide
viii
Contents

CHAPTER 1
Cisco ASR 1001-X Router Overview
The Cisco ASR 1000 Series Aggregation Services Routers are mid-range edge routers that establish a new
price-to-performance class offering benefits to both enterprise and service providers alike. The Cisco ASR
1000 Series Aggregation Services Routers portfolio is based on an innovative custom-built ASIC called
Quantum Flow Processor that aggregates services at scale.
The Cisco ASR 1001-X Router is a part of the Cisco ASR 1000 Series and offers a compact form factor that
consumes less rack space and power while offering 20 Gbps forwarding throughput. The Cisco ASR 1001-X
Router supports all the general-purpose routing and security features of the Cisco ASR 1000 Series
Aggregation Services Routers.
•Hardware Features of the Cisco ASR 1001-X Router, page 1
•Field-Replaceable Units for the Cisco ASR 1001-X Router, page 6
•Cisco Product Identification Standard, page 7
•SPA Slot Numbering, page 9
•Serial Number and PID/VID Label Location, page 9
Hardware Features of the Cisco ASR 1001-X Router
The Cisco ASR 1001-X Router supports:
•Up to 16 GB (8 GB in the base configuration) of DDR3 error-correcting code-protected field- replaceable
memory, with single-bit error correction and multi-bit error detection.
•A nonmodular and fixed Embedded Services Processor (ESP) with a default throughput of 2.5 Gbps
that is upgradable with a software-activated performance license of 5 Gbps, 10 Gbps, or 20 Gbps.
•Up to 8 Gbps security and crypto processing through a dedicated security processor.
•RJ-45 console ports and auxiliary ports, and a mini USB console port.
•One copper Ethernet 10/100/1000 Mbps network management port.
•An embedded USB (eUSB) flash module that supports 8 GB of nonvolatile Flash storage.
•Two USB 2.0 ports for USB flash sticks or USB secure tokens (secure key distribution).
Cisco ASR 1001-X Router Hardware Installation Guide
1

•Stratum 3E network clocking per GR-1244-CORE, using 1588, 10 GE, GE, SPA, or Network Interface
Module (NIM) interfaces as timing sources.
•Six built-in 1 GE SFP-only interfaces (do not support SFP+), and two built-in 10 GE SFP+ interfaces
(support only 10-GE rate) that support SyncE.
•One half-height SPA bay.
•Software redundancy using Dual IOS, similar to all the other nonhardware redundant routers from the
Cisco ASR 1000 Series Aggregation Services Router family.
•LED indicators for Ethernet and console status, as well as visual system state indications.
•Command-line interface (CLI), alarm, network management, logging, statistics aggregation, and on-board
failure logging (OBFL).
•Environmental chassis management.
•10 MB ternary content-addressable memory (TCAM).
•Up to 20 Gbps sustained forwarding data traffic through the chassis.
•One Network Interface Module (NIM) bay.
The NIM bay supports the T1/E1 NIMs and the Solid State Device (SSD) NIM assembly and drive.Note
•Field-replaceable units (FRU) with online insertion and removal (OIR).
Cisco ASR 1001-X Overall Chassis Front View
The following figure shows the front of the Cisco ASR 1001-X Router.
Figure 1: Cisco ASR 1001-X Router Front View
Shared port adapter slot7NIM slots1
USB port 08
CON—One mini eUSB
por
2
USB port 19
PWR—Power LED
3
Cisco ASR 1001-X Router Hardware Installation Guide
2
Cisco ASR 1001-X Router Overview
Cisco ASR 1001-X Overall Chassis Front View

CON—One
RJ-45/RS-232 compatible
console port
10Six built-in 1 GE
SFP-only interfaces (do
not support SFP+), and
two built-in 10 GE SFP+
interfaces (support only
10-GE rate)
4
CRIT LED—Critical
alarm indicator
MAJ LED—Major alarm
indicator
MIN LED—Minor alarm
indicator
11
AUX—One
RJ-45/RS-232 compatible
auxiliary port
5
STAT—Status LED
12
MGMT—One RJ-45
10/100/1000 management
Ethernet port. The
management port has two
LEDs, L and S. L green
indicates Link operations.
S blinks the negotiated
Ethernet speed (1 blink
equals 10 Mbps, 2 blinks
equals 100 Mbps, 3 blinks
equals 1 000 Mbps).
6
Cisco ASR 1001-X Router LEDs
The following figure shows the front panel of the Cisco ASR 1001-X Router.
Figure 2: Common LEDs for the Cisco ASR 1001-X Router
Cisco ASR 1001-X Router Hardware Installation Guide
3
Cisco ASR 1001-X Router Overview
Cisco ASR 1001-X Router LEDs

Behavior in the
Power-Up State
ColorLEDLED LabelNo.
All the power
supplies are within
operational limits.
GreenPowerPWR1
Major alarm
indicator.
RedMAJORMAJ2
Critical alarm
indicator. Will be
off when the router
is initially powered
up and all the
configured
components are
available.
RedCRITICALCRIT3
Minor alarm
indicator
AmberMINORMIN4
Cisco IOS has
successfully booted.
GreenSTATUSSTAT5
The system is at
ROMMON.
Yellow
System failure. Will
be off when the
router is powered
up.
Red
Indicates that the
mini eUSB
connector is used as
the console.
GreenUSB Console
Enable
EN6
Indicates that the
RJ-45 connector is
being used as the
console.
Off
Cisco ASR 1001-X Router Hardware Installation Guide
4
Cisco ASR 1001-X Router Overview
Cisco ASR 1001-X Router LEDs

Cisco ASR 1001-X Management Storage Connections
The following figure shows the Cisco ASR1001-X Router’s management storage connections.
Figure 3: Management Storage Connections for the Cisco ASR 1001-X Router
USB port 14
AUX—One
RJ-45/RS-232 compatible
auxiliary port.
1
CON—One
RJ-45/RS-232 compatible
console port
5
MGMT —one RJ-45
10/100/1000 management
Ethernet port. The
Management Port has two
LEDs, L and S. L green
indicates Link operations.
S blinks the negotiated
Ethernet speed (1 blink 10
Mbps, 2 blinks 100 Mbps,
3 blinks, 1 000 Mbps).
2
—
USB port 03
Cisco ASR 1001-X Chassis Rear View
The following figure shows the rear of the Cisco ASR 1001-X Router with four fans and two AC or DC power
supplies.
Cisco ASR 1001-X Router Hardware Installation Guide
5
Cisco ASR 1001-X Router Overview
Cisco ASR 1001-X Management Storage Connections

Four internal fans draw cooling air into the chassis and across internal components to maintain an acceptable
operating temperature. The fans are located in the center of the chassis. The fans are numbered from 0 to 3,
right to left.
Two power supplies, either two AC power supplies or two DC power supplies are accessed from the rear of
the router and are hot-swappable.
The Cisco ASR 1001-X Router can support two AC or two DC power supplies. Do not install mixed AC
and DC power supply units in the same chassis.
Note
Cisco ASR 1001-X SPA GE and TE Ports
The 10 GE SFP+ ports are indicated in the front bezel with orange highlights, and the GE SFP ports are
indicated with yellow highlights. The following figure shows the port numbering for the 10 GE SFP+ and GE
SFP ports.
GE SFP Port 0/0/2510 GE SFP+ Port 0/0/01
GE SFP Port 0/0/3610 GE SFP+ Port 0/0/12
GE SFP Port 0/0/47GE SFP Port 0/0/03
GE SFP Port 0/0/58GE SFP Port 0/0/14
Field-Replaceable Units for the Cisco ASR 1001-X Router
The Cisco ASR 1001-X Router has a number of FRUs. These include:
•SPAs
•Dual In-line Memory Modules (DIMMs)
•NIMs
•SSD and SSD NIM assembly
•USB flash or secure token memory stick
Cisco ASR 1001-X Router Hardware Installation Guide
6
Cisco ASR 1001-X Router Overview
Cisco ASR 1001-X SPA GE and TE Ports

•AC and DC power supplies
For more information, see “Removing and Replacing FRUs from the Cisco ASR 1001-X Router”.
Cisco Product Identification Standard
This section describes the Cisco products and services product identification standard. This feature provides
you with the ability to effectively integrate and manage Cisco products in your network and business operations.
Unique Device Identifier
The Unique Device Identifier (UDI) is the Cisco product identification standard for hardware products. A
product identification standard removes barriers to enterprise automation and can help you reduce operating
expenses.
The UDI provides a consistent electronic, physical, and associated business-to-business information product
identification standard.
The UDI is a combination of five data elements. The below table lists the UDI elements.
Table 1: UDI Elements
DescriptionPhysical VisibilityElectronic VisibilityUDI Data Element
Product ID, also known
as product name, model
name, product number
YesYesPID
Version IDYesYesVID
Serial number, the unique
instance of the PID
YesYesSN
Type, such as chassis,
slot, or power supply
—
YesEntity Name
Additional product
information
—
YesProduct Description
The combination of serial number and product ID (PID) is unique and consistent across all Cisco products.
The PID that is coded on hardware is called a base product identifier.
Additional orderable PIDs can be associated to a base PID. For instance, an orderable PID may describe a
packaging configuration for a product or a bundled group of products sold, tested, and shipped together.
Specific unique device identifier (UDI) benefits include the following:
•Identifies:
◦Individual Cisco products in your networks
◦PIDs and serial numbers for service and replaceable products
Cisco ASR 1001-X Router Hardware Installation Guide
7
Cisco ASR 1001-X Router Overview
Cisco Product Identification Standard

◦Version IDs (VIDs) for product version visibility
•Facilitates discovery of products subject to recall or upgrade
•Enhances inventory automation of Cisco products
The Cisco product identification standard provides the following features:
•Version visibility—Cisco continuously improves products through feature additions. Product changes
are indicated by incrementing the VID, which provides version visibility to help you understand and
manage product changes. VID management ensures consistency of changes from product to product.
•Operating expense reduction—Cisco UDIs provide accurate and detailed network inventory information;
identifying each Cisco product in a network element through a standard interface. Cisco operating
systems can view and use this data, allowing you to automate your electronic inventory.
•Consistency across product layers—The UDIs are embedded in the hardware products and cannot be
overwritten. Operating and management systems discover UDIs through standard interfaces and display
UDIs in standard outputs. Standard interfaces include the IETF standard ENTITY-MIB.
show diag subslot eeprom Command
The show diag subslot eeprom command displays the PID, VID, PCB serial number, hardware revision, and
other such information.
The following is sample output from the show diag subslot eeprom command:
Router# show diag subslot 0/0 eeprom
MIDPLANE EEPROM data:
Product Identifier (PID) : ASR1001-X
Version Identifier (VID) : V00
PCB Serial Number : JAE17450EUV
Top Assy. Part Number : 68-4703-06
Hardware Revision : 0.1
Asset ID :
CLEI Code : CMMP410DRA
Common Language Equipment Identification (CLEI) code is a ten-digit character code that identifies a
specific product. A CLEI code is applied to each part within a Cisco ASR1001-X Router as they are
programmed in manufacturing for shipment to customers.
Note
show license udi Command
The show license udi command displays UDI information.
The following is sample output from the show license udi command:
Router# show license udi
SlotID PID SN UDI
--------------------------------------------------------------------------------
*6 ASR1001-X JAE17190302 ASR1001-X:JAE17190302
For complete information on the product identification standard, see http://www.cisco.com/go/udi/
Note
Cisco ASR 1001-X Router Hardware Installation Guide
8
Cisco ASR 1001-X Router Overview
Unique Device Identifier

SPA Slot Numbering
A shared port adapter (SPA) is a modular type of port adapter that can be inserted into a subslot to provide
network connectivity and increased interface port density. The Cisco ASR 1001-X Router supports one flexible
integrated NIM slot and one half-height SPA bay.
The following figure shows slot numbering on the Cisco ASR 1001-X Router.
Figure 4: Cisco ASR 1001-X Router Slot Numbering
Serial Number and PID/VID Label Location
The following figure shows a Cisco ASR 1001-X Router chassis along with the location of the serial number
and the PID/VID label.
Figure 5: Cisco ASR 1001-X Router Serial Number and PID/VID Label Location
Cisco ASR 1001-X Router Hardware Installation Guide
9
Cisco ASR 1001-X Router Overview
SPA Slot Numbering

Cisco ASR 1001-X Router Hardware Installation Guide
10
Cisco ASR 1001-X Router Overview
Serial Number and PID/VID Label Location

CHAPTER 2
Cisco ASR 1001-X Router Supported Hardware
Components
This chapter contains information about the supported hardware components on the Cisco ASR 1001-X
Router, and contains the following sections:
•Supported Hardware Components, page 11
•Supported Half-Height SPAs, page 12
•Supported Small Form-Factor Pluggable (SFP and SFP+) Transceivers, page 14
•Supported NIMs, page 15
•Cisco ASR 1001-X Router Power Supplies, page 17
Supported Hardware Components
The following table lists the hardware components supported on the Cisco ASR 1001-X Router.
Table 2: Supported Hardware Components
DescriptionComponent
1 RU form factorChassis
Six built-in Gigabit Ethernet and two built-in
10-Gigabit Ethernet ports
Ethernet Ports
A nonmodular, fixed ESP with a default throughput
of 2.5 Gbps, which is upgradable with a
software-activated performance license of 5 Gbps,
10 Gbps, or 20 Gbps.
ESP
Single integrated route processorRoute Processor
Integrated SIPSIP
Cisco ASR 1001-X Router Hardware Installation Guide
11

DescriptionComponent
1 half-height (HH) SPA baySPA Slots
1NIM Slots
2USB Slots
Supported Half-Height SPAs
The following table lists the supported half-height SPAs on the Cisco ASR 1001-X Router.Supported
Half-Height SPAs
Table 3: Supported Half-Height SPAs
DescriptionPID
Cisco 1-Port 10GE LAN-PHYSPA-1X10GE-L-V2
1-port Channelized STM-1/OC-3c to DS0SPA-1XCHSTM1/OC3
1-port OC12/STM4 POSSPA-1XOC12-POS
2-port OC12/STM4 POSSPA-2XOC12-POS
4-port OC-12/STM-4 POSSPA-4XOC12-POS
8-port OC12/STM4SPA-8XOC12-POS
1-port OC-3c/STM-1 ATMSPA-1XOC3-ATM-V2
Cisco 2-Port Gigabit EthernetSPA-2X1GE-V2
2-port Channelized T3 to DS0SPA-2XCT3/DS0
2-port OC3/STM1 POSSPA-2XOC3-POS
8-port OC-3/STM-1 POSSPA-8XOC3-POS
1-port OC48/STM16 POS/RPRSPA-1XOC48POS/RPR
2-port OC48/STM16 POS/RPRSPA-2XOC48POS/RPR
2-port Clear Channel T3/E3SPA-2XT3/E3
3-port OC-3c/STM-1 ATMSPA-3XOC3-ATM-V2
Cisco 4-Port Fast Ethernet (TX)SPA-4X1FE-TX-V2
Cisco ASR 1001-X Router Hardware Installation Guide
12
Cisco ASR 1001-X Router Supported Hardware Components
Supported Half-Height SPAs