Cisco 1800 Series Original instructions

Americas Headquarters:
© 2007 Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Regulatory Compliance and Safety Information
for Cisco 1800 Integrated Services
Routers (Fixed)
This publication provides international regulatory compliance and safety information for Cisco 1800
Integrated Services Routers (fixed configuration). The model numbers are printed on the bottom
homologation labels with the approval logos and certification numbers.
Use this publication with other documentation that is available for your router.
This document contains the following sections:
•Safety, page 1
•Electromagnetic Compatibility, page 4
•Telecommunications, page 8
•Declaration of Conformity Statements, page 13
•California Perchlorate Contamination Prevention Act—Title 22, California Code of Regulations,
Chapter 33, page 13
•Translated Safety Warnings, page 13
•Obtaining Documentation, Obtaining Support, and Security Guidelines, page 73
Safety
This section describes safety conditions and operating conditions for Cisco 1800 fixed configuration
routers. It contains the following:
•Agency Approvals and Standards
•Restricted Area
•Lithium Backup Battery
•Operating Conditions for Canada

2
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Safety
•Operating Conditions for Australia and the European Community
•Operating Conditions for the United Kingdom
Warning This equipment will be inoperable when mains power fails. Statement 198
Warning High leakage current—permanent earth connection essential before making Telecommunication
Network Connection. Statement 343
Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network
voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some
LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021
Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface. Statement 1037
Warning Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote
risk of electric shock from lightning. Statement 1038
Warning For connections outside the building where the equipment is installed, the following ports must be
connected through an approved network termination unit with integral circuit protection.
10/100/1000 Ethernet Statement 1044
Warning Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if
interconnections are made using uninsulated exposed metal contacts, conductors, or terminals.
Avoid using such interconnection methods, unless the exposed metal parts are located within a
restricted access location and users and service people who are authorized within the restricted
access location are made aware of the hazard. A restricted access area can be accessed only
through the use of a special tool, lock and key or other means of security. Statement 1072
Warning No user-serviceable parts inside. Do not open. Statement 1073
Agency Approvals and Standards
This section lists the following agency approvals and standards for safety:
•CSA Certified to UL 60950 and CSA 22.2 No. 60950
•ACA to AS/NZS 60950
•CB Certificate/Test Report to IEC 60950-1, edition 1 (2001) with all country deviations, as well as
to EN 60950-1

3
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Safety
Restricted Area
The following warning is applicable only in Scandinavian countries.
Warning This unit is intended for installation in restricted access areas. A restricted access area can be
accessed only through the use of a special tool, lock and key, or other means of security.
Statement 1017
Lithium Backup Battery
Cisco 1800 fixed configuration routers have an internal real-time clock with battery backup. The backup
battery is a socketed lithium battery. This battery lasts the life of the router under the operating
environmental conditions specified for the router, and is not field-replaceable.
Note Although the lithium battery is not intended to be field-replaceable, the safety agencies require that the
following warning be included in this document.
Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturer’s instructions. Statement 1015
Operating Conditions for Canada
In addition to the warnings and safety guidelines listed in the “Translated Safety Warnings” section on
page 13 in this document, the following operating conditions apply to routers used in Canada:
The Canadian Department of Communications label identifies certified equipment. This certification
means that the equipment meets certain telecommunications network protective operational and safety
requirements. The Department does not guarantee that the equipment will operate to the
user’s satisfaction.
Before installing the equipment, users should ensure that it is permissible to be connected to the facilities
of the local telecommunications company. The equipment must also be installed using an acceptable
method of connection. In some cases, the company’s inside wiring associated with a single line
individual service may be extended by means of a certified connector assembly (telephone extension
cord). The customer should be aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility
designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request the user to disconnect the
equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas.

4
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Electromagnetic Compatibility
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Operating Conditions for Australia and the European Community
The warnings and safety guidelines listed in the section “Translated Safety Warnings” section on page 13
in this document apply to routers used in Australia and the European Community.
Operating Conditions for the United Kingdom
In addition to the warnings and safety guidelines listed in the section “Translated Safety Warnings”
section on page 13 in this document, the following warnings and safety guidelines apply to routers used
in the United Kingdom:
•The router is designed to meet the requirements of interim CTR3 for Basic Rate Access.
•Interconnection directly, or by way of other apparatus, of ports marked:
“Safety Warning—See instructions for use”
with ports marked or not so marked may produce hazardous conditions on the network, and that
advice should be obtained from a competent engineer before such a connection is made.
•The BRI connector must be hardwired permanently to the S-reference connection point by using a
connect one-time-only, nonremovable plug (RJ-45 with the latch tab removed).
•The ports marked “10BaseT,” “Console,” and “ISDN” have a safety warning applied to them as
follows:
“These ports do not provide isolation sufficient to satisfy the requirement of EN41003; apparatus
connected to these ports should either have been approved to EN41003 or have previously been
evaluated against B5E301 British Telecommunications plc (Post Office) Technical Guides 2 or 26
and given permission to attach; any other usage will invalidate any approval given to this apparatus.”
Other usage will invalidate any approval given to this apparatus if as a result it ceases to comply with
EN41003:1993.
•This apparatus must be connected to a main socket outlet with a protective earth contact.
•Connection of power supply: The router is intended for use when supplied with power from a supply
providing 100 to 240 VAC, 50 to 60 Hz, up to 0.5A.
Electromagnetic Compatibility
This section describes electromagnetic compatibility (EMC) compliance conditions for the
Cisco 1800 fixed configuration routers. It contains the following:
•Country Approvals and Standards
•CISPR 22 Class A Warning
•FCC Part 15 Notice
•Class A Notice for Canada
•Statement 191—VCCI Class A Warning for Japan

5
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Electromagnetic Compatibility
•Statement 371—Power Cable and AC Adapter for Japan
•Statement 256—Class A Warning for Hungary
•Statement 294—Class A Warning for Korea
Country Approvals and Standards
This section lists the following country approvals and standards for EMC:
•Emissions for the Cisco 1800 fixed configuration routers—47CFR15 Class A (FCC); CISPR22
Class A; EN55022 Class A; AS/NZS 3548 Class A (ACA); ICES-003 Class A (Industry Canada);
V-3 Class A (VCCI); EN61000-3-2; EN61000-3-3; EN300386 Class A; KN 22 (Korea)
•Immunity for Cisco 1800 fixed configuration routers—EN55024, EN50082-1, and EN61000-6-1
(including EN 61000-4-2 Electrostatic Discharge; EN 61000-4-3 Radiated Susceptibility; EN
61000-4-4 Electrical Fast Transients; EN 61000-4-5 Power & Signal Line Surges; EN 61000-4-6
Injected RF Swept Immunity; EN61000-4-11 Voltage Dips + Sags); EN300386
CISPR 22 Class A Warning
Warning This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
FCC Part 15 Notice
Cisco 1800 fixed configuration routers comply with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. These devices may not cause harmful interference.
2. These devices must accept any interference received, including interference that may cause
undesired operation.
Modifying the equipment without authorization from Cisco may result in the equipment no longer
complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use
the equipment may be limited by FCC regulations, and you may be required to correct any interference
to radio or television communications at your own expense.
Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

6
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Electromagnetic Compatibility
Class A Notice for Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Equipment Attachment Limitations
The Industry Canada label identifies certified equipment. This certification means that the equipment
meets certain telecommunications network protective, operational, and safety requirements as
prescribed in the appropriate Terminal Equipment Technical Requirement Documents. The Department
does not guarantee the equipment will operate to the user’s satisfaction.
Note This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The abbreviation, IC, before the registration number
signifies that registration was performed based on a Declaration of Conformity indicating that Industry
Canada technical specifications were met. It does not imply that Industry Canada approved the
equipment.
Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection. In some cases, the company’s inside wiring associated with a
single-line individual service may be extended by means of a certified connector assembly (telephone
extension cord). The customer should be aware that compliance with the above conditions might not
prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility
designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request the user to disconnect the
equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines, and internal metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas.
Caution Users should not attempt to make such connections themselves, but should contact the appropriate
electrical inspection authority, or electrician, as appropriate.

7
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Electromagnetic Compatibility
Statement 191—VCCI Class A Warning for Japan
Statement 371—Power Cable and AC Adapter for Japan
When installing the product, please use the provided or designated connection cables/power cables/AC
adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and
Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for
any other electrical devices than products designated by CISCO. The use of cables that are certified by
Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to
CISCO-designated products.
Statement 256—Class A Warning for Hungary
Warning This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio
disturbance may arise. When such trouble occurs, the user may be required to take corrective
actions.
Warning This equipment is a class A product and should be used and installed properly according to the
Hungarian EMC Class A requirements (MSZEN55022). Class A equipment is designed for typical
commercial establishments for which special conditions of installation and protection distance are
used.

8
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Telecommunications
Statement 294—Class A Warning for Korea
Telecommunications
This section describes telecommunications compliance conditions for Cisco 1800 fixed configuration
routers. It contains the following:
•Country Approvals and Standards
•FCC Part 68 Notice
•Universal Service Order Code Jacks
•Router Port Approvals—FCC and Industry Canada
•Declarations of Conformity to R&TTE Directive 1999/5/EEC for the European Community,
Switzerland, Norway, Iceland, and Liechtenstein
Country Approvals and Standards
This section lists the following agency approvals and standards for Telecommunications:
•USA—TIA-968-A, TI.TRQ.6
•Canada—CS-03
•European Union—RTTE Directive 5/99
•Argentina—CTR 21, TBR 21
•Australia—AS/ACIF-S002, AS/ACIF-S003, AS/ACIF-S016, AS/ACIF-S031, AS/ACIF-S038,
AS/ACIF-S043, ACIF-C559
•Brazil—225-540-784, 225-540-788, CTR3, 225-100-717 Edition 3, NET 001/92 1990
•China—ITU-G.992.1, ITU-G.991.2, CTR3, ITU I.431 1993
•Hong Kong—HKTA-2011, HKTA-2013, HKTA-2014, HKTA-2017, HKTA-2033
•India—I-DCA-18-2, IR-I/TCP-01/02, IR-I/PRI-01/02
•Israel—TIA-968-A accepted, TBR21
•Japan—Technical condition (DoC acceptance in process)
•Korea—TIA-968-A/RRL 2005-96
Warning This is a Class A Device and is registered for EMC requirements for industrial use. The seller or
buyer should be aware of this. If this type was sold or purchased by mistake, it should be replaced
with a residential-use type.

9
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Telecommunications
•Mexico—TIA-968-A accepted
•New Zealand—PTC-217, PTC-220, PTC 270/272, CTR3, ACA 016, ACIF S016
•Singapore—IDA TS ADSL1 Issue 1, IDA TS ADSL 2, IDA TS HDSL, IDA TS ISDN 1 Issue 1 1999,
IDA TS ISDN 3 Issue 1 1999, IDA TS PSTN 1 Issue 4, IDA TS PSTN 1 Issue 4, IDA TS PSTN 1 Issue 4
•South Africa—DPTE-TE-001, TIA-968-A accepted
•Taiwan—PSTN01, TIA-968-A accepted
FCC Part 68 Notice
This equipment complies with Part 68 of the FCC rules. On the bottom of the chassis is a label that
contains, among other information, the FCC registration number and ringer equivalence number (REN)
for this equipment. If requested, this information must be provided to the telephone company.
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. If advance notice is not practical, the
telephone company will notify the customer as soon as possible. Also, you will be advised of your right
to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operation, or procedures that
could affect the operation of this equipment. If this happens, the telephone company will provide
advance notice in order for you to make the necessary modifications to maintain uninterrupted service.
Normally, this equipment will be used in conjunction with FCC registered equipment that limits the
Encoded Analog Content that provides the required Billing Protection. If the connected equipment is not
of this type, an affidavit must be supplied to the telephone company where the network connection is to
be made. The affidavit is to be notarized, and is to be filed at least ten days before the initial connection.
The facility interface and service order codes are shown in Table 1.
Table 1 Cisco 1800 Fixed Configuration Routers Facility Interface and Service Order Codes
Interface Type
Facility Interface Code
(FIC)
Service Order Code
(SOC) Jack Type (USOC)
ADSL Metallic — RJ-11C
SHDSL Metallic — RJ-11C
RJ-14C
BRI - S/T 02IS5 6.0N RJ-49C via NT1
BRI-U 02IS5 6.0N RJ-49
T1 data 04DU9-BN
04DU9-DN
04DU9-1KN
04DU9-1SN
6.0N RJ-48C
T1 voice 04DU9-BN
04DU9-DN
04DU9-1KN
04DU9-1SN,
04DU9-1ZN
6.0Y RJ-48C

10
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Telecommunications
Universal Service Order Code Jacks
Table 2 lists the universal service order code (USOC) jacks used by Cisco 1800 fixed configuration
routers.
FXO1 02LS2
02GS2
—RJ-11C
RJ-21X
CAMA1 02RV2-0 — RJ-11C
RJ-21X
DID (Reverse battery) 02RV2-T 9.0F (AS.2) RJ-11C
RJ-21X
E&M tie trunk TL11E
TL12E
TL31E
TL32E
9.0F RJ-2EX
RJ-2FX
RJ-2GX
RJ-2HX
Analog modem1 — — RJ-11C
DSU 56K 04DU5-24
04DU5-48
04DU5-96
04DU5-19
04DU5-38
04DU5-56
04DU5-64
04DU5-56B
6.0F RJ-48S
Table 1 Cisco 1800 Fixed Configuration Routers Facility Interface and Service Order Codes
Interface Type
Facility Interface Code
(FIC)
Service Order Code
(SOC) Jack Type (USOC)
Table 2 USOC Jacks for Cisco 1800 Routers and WAN Interface Cards
Cisco Product Number Facility Interface Code Service Order Code Jack Type
Cisco 1800 02IS5 6.0N CB-1D
Cisco 1800 02DE2 7.0Y RJ-11
Cisco 1800 02LS2 9.0Y RJ-11
WIC-1B-S/T-V3 02IS5 6.0N RJ-48C
WIC-1B-U-V2 02IS5 6.0N RJ-49C
WIC-1DSU-T1-V2 04DU9-BN/DN 6.0N RJ-48C
WIC-1DSU-56K4 04DU5-56 6.0N R3-48S
WIC-1ADSL Metallic 6.0N RJ-11
WIC-1ADSL-DG Metallic 6.0N RJ-11