Cisco ASR 907 Manual

Cisco ASR 907 Router Hardware Installation Guide
First Published: 2015-10-01
Last Modified: 2019-07-31
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

©2015–2019 Cisco Systems, Inc. All rights reserved.

CONTENTS
Cisco ASR 907 Router Overview 1
CHAPTER 1
Cisco ASR 907 Router Features 1
System Specifications 3
GNSS Module (A900-CM-GNSS) 4
GNSS Module RF Input Requirements 4
Power Supply Features 5
Redundancy 6
Dying Gasp 6
Status LEDs 6
Fan Tray 6
Dust Filter (A907-FAN-F) 7
Air Plenum (A907-F2B-AIR-U) 7
RSP Modules 7
Supported RSPs 8
Supported RSP Features 8
Supported Interface Modules 9
RSP Redundancy 12
Network Timing Interfaces 12
RSP Interfaces 13
Interface Modules 13
8-Port 1 Gigabit Ethernet SFP Interface Module (A900-IMA8S) 14
8-Port 1 Gigabit Ethernet RJ45 Interface Module (A900-IMA8T) 15
1-Port 10 Gigabit Ethernet XFP Interface Module (A900-IMA1X) 15
8-port 10 Gigabit Ethernet Interface Module (8x10GE) (A900-IMA8Z) 16
8-Port 1 Gigabit Ethernet SFP with 1-Port 10 Gigabit Ethernet Combination Interface Module
(A900-IMA8S1Z) 16
Cisco ASR 907 Router Hardware Installation Guide
iii

8-Port 1 Gigabit Ethernet + 1-Port 10 Gigabit Ethernet SFP+ Combination Interface Module
(A900-IMA8T1Z) 17
2-Port 10 Gigabit Ethernet SFP+ Interface Module (A900-IMA2Z) 18
1-Port 100 Gigabit Ethernet Interface Module (1x100GE) (A900-IMA1C) 19
2-Port 100 Gigabit Ethernet Interface Module (2X100GE) (N560-IMA2C) 19
2-Port 40 Gigabit Ethernet QSFP Interface Module (2x40GE) (A900-IMA2F) 20
8/16-Port 1 Gigabit Ethernet (SFP / SFP) + 1-port 10 Gigabit Ethernet (SFP+) / 2-port 1 Gigabit
Ethernet (CSFP) Interface Module (A900-IMA8CS1Z-M) 20
16-Port T1/E1 Interface Module (A900-IMA16D) 21
32-Port T1/E1 Interface Module (A900-IMA32D) 22
8-port T1/E1 Interface Module (A900-IMA8D) 23
48-Port T1/E1 CEM Interface Module (A900-IMA48D-C) 23
48-Port T3/E3 CEM Interface Module (A900-IMA48T-C) 24
1-port OC-48/STM-16 or 4-port OC-12/OC-3 / STM-1/STM-4 + 12-Port T1/E1 + 4-Port T3/E3
CEM Interface Module (A900-IMA3G-IMSG) 25
1-Port OC-192 or 8-Port Low Rate CEM Interface Module (10G HO / 10G LO)
(A900-IMA8S1Z-CX) 25
ASR 900 Combo 8-Port SFP GE and 1-Port 10GE With CEM/iMSG, 20G Interface Module
(A900-IMA1Z8S-CXMS) 27
Temperature Sensor 29
Interface Numbering 29
Regulatory Compliance 29
Preparing for Installation 31
CHAPTER 2
Safety Guidelines 31
Standard Warning Statements 31
Safety Guidelines for Personal Safety and Equipment Protection 33
Safety Precautions for Module Installation and Removal 33
Safety with Electricity 34
Power Supply Considerations 38
Preventing ESD Damage 38
Site Planning 39
General Precautions 39
Site Planning Checklist 39
Site Selection Guidelines 39
Cisco ASR 907 Router Hardware Installation Guide
iv
Contents

Environmental Requirements 40
Physical Characteristics 40
Assembly Guidelines 40
Air Flow Guidelines 40
Air Flow Guidelines for Enclosed Rack Installation 44
Floor Loading Considerations 44
Site Power Guidelines 44
Electrical Circuit Requirements 46
Site Cabling Guidelines 46
Asynchronous Terminal Connections 47
Interference Considerations 47
Rack-Mounting Guidelines 47
Precautions for Rack-Mounting 48
Rack Selection Guidelines 48
Equipment Rack Guidelines 48
Installation Checklist 49
Creating a Site Log 50
Receiving the Cisco ASR 907 Router 50
Chassis-Lifting Guidelines 51
Tools and Equipment 52
Unpacking and Verifying the Shipped Contents 53
Installing the Cisco ASR 907 Router 55
CHAPTER 3
Prerequisites 55
Installing the Router in a Rack 55
Installing the Chassis Brackets 55
Installing the Router Chassis in the Rack 56
Installing Plenum A907-F2B-AIR-U Assembly and Chassis in the Rack 59
Installing the Chassis in the Air Plenum 64
Attaching the Cable Management Brackets 65
Installing the Chassis Ground Connection 66
Installing the Fan Tray 69
Removing and Replacing the Dust Filter 70
Removing the Dust Filter 71
Cisco ASR 907 Router Hardware Installation Guide
v
Contents

Dust Filter Maintenance 71
Removing and Replacing the Fan Tray 72
RSP Installation 74
Installing an RSP Module 74
Removing an RSP Module 76
Hot-Swapping an RSP Module 77
Installing the Interface Module Carrier 78
Interface Module Installation 78
Installing an Interface Module 79
Removing an Interface Module 80
Hot-Swapping an Interface Module 80
Installing the Power Supply 82
Preventing Power Loss 83
Power Connection Guidelines 83
Guidelines for DC-Powered Systems 84
Guidelines for AC-Powered Systems 84
Installing the DC Power Supply 84
Installing the DC Power Supply Module 84
Connecting DC Power Supply Unit (A900-PWR900-D2) 85
Activating the DC Power Supply 87
Removing and Replacing the DC Power Supply 88
Installing the AC power Supply 89
Installing the AC Power Supply Module for A900-PWR1200-A (1200 W) 89
Recommended Power Cables 90
Activating the AC Power Supply 91
Removing and Replacing the AC Power Supply 91
Installing Dust Caps 92
Connecting the Cisco ASR 907 Router to the Network 93
Connecting Console Cables 93
Connecting to the Serial Port using Microsoft Windows 93
Connecting to the Console Port using Mac OS X 96
Connecting to the Console Port using Linux 96
Installing the Cisco Microsoft Windows USB Device Driver 97
Uninstalling the Cisco Microsoft Windows USB Driver 98
Cisco ASR 907 Router Hardware Installation Guide
vi
Contents

Connecting to the Auxiliary Port 99
Connecting a Management Ethernet Cable 101
Installing and Removing SFP and XFP Modules 101
Connecting a USB Flash Device 101
Removing a USB Flash Device 102
Connecting Timing Cables 102
Connecting Cables to the BITS Interface 102
Connecting Cables to a GNSS Interface 103
Connecting a Cable to the GNSS Antenna Interface 104
Connecting Ethernet Cables 105
Connecting Cables to SFP Modules 106
Connecting T1/E1 Cables 106
Installing the Cable Connectors 106
T1/E1 Pinouts 109
RJ45 Cable Pinouts 109
RJ48 Cable Pinouts 109
Connecting Cables to the Patch Panel 109
Patch Panel Pinout 110
Patch Panel Cabling for Redundancy 110
Recommended Patch Panel 112
Installing Patch Panel 113
Install 3G Patch Panel 117
Install Rack Brackets 118
Set up 3G Patch Panel on Rack 125
Wall Mount 3G Patch Panel 137
Patch Panel Dimensions 139
Connecting Serial Cables 144
Connecting the Fan Tray Alarm Port 145
Connector and Cable Specifications 146
Cisco Router Initial Configuration 147
CHAPTER 4
Checking Conditions Prior to System Startup 147
Powering Up the Cisco ASR 907 Router 148
Verifying the Front Panel LEDs 150
Cisco ASR 907 Router Hardware Installation Guide
vii
Contents

Verifying the Hardware Configuration 151
Checking Hardware and Software Compatibility 151
Configuring the Cisco ASR 907 Router at Startup 151
Using the Console Interface 151
Configuring Global Parameters 152
Checking the Running Configuration Settings 153
Saving the Running Configuration to NVRAM 154
Safely Powering Off the Cisco ASR 907 Router 154
Troubleshooting 157
CHAPTER 5
Pinouts 157
BITS Port Pinout 157
GPS Port Pinout 158
Time of Day Pinout 158
Alarm Port Pinout 159
Console/Aux RJ45 RS232 Serial Port Pinout 159
T1/E1 Port Pinout 160
16 T1/E1 Interface Module Pinout 160
32 T1/E1 Interface Module Pinout 162
8 T1/E1 Interface Module —RJ48C Port Pinnouts 165
AMP64 Pinouts 166
Patch Panel Pinout 171
Serial Cable Pinouts 176
DB-9 Connector Pinouts 176
RJ-45 Connector Pinouts 177
RJ-48 Connector Pinouts 178
Management Ethernet Port Pinout 179
USB Console Port Pinout 179
USB Flash/MEM Port Pinout 180
Fiber-Optic Specifications 180
LED Summary 181
RSP LEDs 181
ASR900-RSP LED 181
ASR900-RSP3C-400-W LED Fault Condition 182
Cisco ASR 907 Router Hardware Installation Guide
viii
Contents

Interface Module LEDs 183
1-Port OC-192 or 8-Port Low Rate CEM Interface Module LEDs 184
48 T1/E1 and 48 T3/E3 Interface Module LEDs 185
OC-3 Interface Module LEDs 186
T1/E1 Interface Module LEDs 186
Serial Interface Module LEDs 189
Power Supply LEDs 189
Fan Tray LEDs 190
Alarm Conditions 191
Site Log and Manufactures 193
APPENDIX A
Manufactures 194
Cisco ASR 907 Router Hardware Installation Guide
ix
Contents

Cisco ASR 907 Router Hardware Installation Guide
x
Contents

CHAPTER 1
Cisco ASR 907 Router Overview
The Cisco ASR 907 Router seven-rack unit router that belongs to the Cisco ASR90x family of routers. This
router complements Cisco’s offerings for IP RAN solutions for the GSM, UMTS, LTE and CDMA. Given
its form-factor, interface types and GigabitEthernet density the Cisco ASR 907 Router can also be positioned
as a Carrier Ethernet aggregation platform.
The Cisco ASR 907 Router is a cost optimized, fully redundant, centralized forwarding, extended temperature,
and flexible pre-aggregation router.
•Cisco ASR 907 Router Features, on page 1
•Interface Numbering, on page 29
•Regulatory Compliance, on page 29
Cisco ASR 907 Router Features
The key feature of the Cisco ASR 907 Router is to increase per platform and rack-unit interface density,
especially when combining multiple interface types such as Gigabit Ethernet (GE), TDM, 10GE, 40GE, and
100GE.
The Cisco ASR 907 Router has the following hardware features:
• A larger service scale and higher throughput (400G) Route Switch Processors
(RSP)—A900-RSP3C-400-W
• One-port 100GE Interface Module (A900-IMA1C)
• Two-port 100GE QSFP28 Interface Module (N560-IMA2C)
After SSO, the packet rate increases and the packet count may vary.
Note
• Two-port 40GE Interface Module (A900-IMA2F)
• 1200-Watt PSUs to power the new RSP modules.
The Cisco ASR 907 Router includes the following specific components:
• Larger chassis—7 rack units in height while still maintaining a shallow depth and side-to-side airflow.
• Larger fan-tray with removable dust filter.
Cisco ASR 907 Router Hardware Installation Guide
1

• New form factor and higher performance RSP—This high performance RSP has aggregate switching
capacity of 480 Gbps in oversubscribed mode.
• The backplane and the RSP together have the provision to support higher density 10GE modules like
8x10GE and 100GE modules.
• Airflow baffle to allow a system to redirect air and allow front-to-back airflow for cooling.
• Flexible I/O configurations through 16 hot pluggable interface modules (single width). For example,
with RSP3-400-W in oversubscribed mode:
• 16x10G + 2x100G + 80x1G
• 48x10G
• Metro ENET switching features along with TDM pseudowire support.
• Network processor provides flexibility to off-load control plane CPU processing for select OAM and
management packets (for example, CCM, BFD, LBM).
• Flexible ENET processing through table-driven packet processing engines.
• On-line insertion or removal (OIR) of all FRUs except GPS module, while the system is operational.
• Power supply (1+1)—Support for both, AC and DC power supplies. A single power supply can support
full system load. If there are two PSUs in the system, they work in a load-sharing mode.
• Fully redundant system with redundant combined control plane and data plane (excluding interfaces),
timing support, power supplies, and fans.
• Active and standby support of redundant control plane and data plane, and timing
• Intrachassis IOS redundancy (requires both RSPs).
• Stateful-switchover (50 ms) between active and standby RSPs (for protocols that are supported by IOS).
• In-service software upgrade (ISSU) supported with same RSPs.
• Timing support for receipt and distribution of network frequency and time including SyncE, BITS,
1PPS/10MHz I/O, IEEE 1588-2008, and NTP.
• Support for ENET OAM.
• T1/E1 line protection compliant with NEBS GR-1089.
The following image illustrates the Cisco ASR 907 Router chassis design.
Cisco ASR 907 Router Hardware Installation Guide
2
Cisco ASR 907 Router Overview
Cisco ASR 907 Router Features

Figure 1: Cisco ASR 907 Router Chassis Design
IM Carrier plates2Interface modules1
Redundant power units (two DC power units are shown).4RSP Units3
Fan tray filter6Fan tray5
System Specifications
The table below summarizes the system specifications and environmental requirements for the Cisco ASR
907 Router.
Table 1: Cisco ASR 907 Router System Specifications
12.224 inches x 17.426 inches x 9.33 inchesDimensions (Height x Width x Depth)
12.224 inches x 17.426 inches x 10.705 inches
The additional depth is due to the projection of the handle from Chassis
face.
Note
Dimensions with FRUs
Weight
15.868 kg
Chassis with back-plane
3.618 kgFan tray
0.924 kg1200W DC PSU
1.0 kg1200W AC PSU
2.46 kgRSP (A900-RSP3C-400-W)
Cisco ASR 907 Router Hardware Installation Guide
3
Cisco ASR 907 Router Overview
System Specifications

The Cisco ASR 907 Router (with industrial temperature optics) supports the
following temperature ranges at 1800 m operating altitude:
• -40º C to 65º C
Operating Temperature
-40º F to 158º F (-40º C to +70º C) storage temperatureNonoperating Temperature
5–95% operating non-condensing relative humidityOperating Humidity
-60 m to 1800 m operating altitude for full operating temperature range; up to 4000
m at up to 40º C.
Operating Altitude
-60 m to 4570 m storage altitudeNonoperating Altitude
1.0 g from 1.0 to 150 HzVibration
30 G half sine 6 ms and 11 msShock
Random: 1.15 g RMS 3 to 200 Hz, 30 minutes/axis
Sine: 10 to 500 Hz at 0.8 G peak / 5 sweep cycles/axis
Nonoperating Vibration
< 76 dBA at 27ºC as per NEBS standard GR-63Operating Acoustics
GNSS Module (A900-CM-GNSS)
The GNSS module is present on the RSP. It is a pluggable module that allows direct interface with the external
antenna.
Using a single GPS antenna input for both RSPs requires usage of external splitters.
Note
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023
Warning
The GNSS module is not hot swappable.
Note
GNSS Module RF Input Requirements
• The GNSS module requires an active GPS/GNSS antenna with built-in Low-Noise Amplifier (LNA) for
optimal performance. The antenna LNA amplifies the received satellite signals for two purposes:
• Compensation of losses on the cable
• Lifting the signal amplitude in the suitable range for the receiver frontend
The Amplification required is 22dB gain + cable/connector loss + Splitter signal loss.
The recommended range of LNA gain (LNA gain minus all cable and connector losses) at the connector
of the receiver module is 22dB to 30dB with a minimum of 20dB and a maximum of 35dB.
Cisco ASR 907 Router Hardware Installation Guide
4
Cisco ASR 907 Router Overview
GNSS Module (A900-CM-GNSS)

• GNSS module provides 5V to the active antenna through the same RF input.
• Surge requirement:
• GNSS modules have built-in ESD protections on all pins, including the RF-input pin. However,
additional surge protection may be required if rooftop antennas are being connected, to meet the
regulations and standards for lightning protection in the countries where the end-product is installed.
• A lightning protection must be mounted at the place where the antenna cable enters the building.
The primary lightning protection must be capable of conducting all potentially dangerous electrical
energy to PE (Protective Earth).
• Surge arrestors should support DC-pass and suitable for the GPS frequency range (1.575GHz) with
low attenuation.
• Antenna Sky visibility:
• GPS signals can only be received on a direct line of sight between antenna and satellite. The antenna
should see as much as possible from the total sky. For proper timing, minimum of four satellites
should be locked.
The antenna terminal should be earthed at the building entrance in accordance
with the ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section
820.93, Grounding of Outer Conductive Shield of a Coaxial Cable.
Note
• Use a passive splitter if more than one GNSS modules are fed from a single antenna.
Power Supply Features
The Cisco ASR 907 Router supports 1200W DC/AC power supplies on all the three PSU slots.
The AC and DC power supplies support:
• -40.8 VDC to -72 VDC
• 85 VAC to 264 VAC
The power supplies are hot-swappable. They are enclosed to prevent exposure to high voltages, and therefore,
no power cable interlock is required. However the power supplies are automatically shut down when removed
from the chassis. The power supplies are rated to deliver 1200W (~100A at +12VDC) to the other FRUs in
the system and are rated for operation at 5ºC above the chassis operating temperature.
See the below tables for the AC and DC power supply specifications.
Table 2: DC Power Supply Specifications
A900-PWR1200-DPart numbers
48V, GND, -48VInput power specification
-40.8 VDCMinimum input voltage
-72 VDCMaximum input voltage
Cisco ASR 907 Router Hardware Installation Guide
5
Cisco ASR 907 Router Overview
Power Supply Features

+12 VDCOutput voltage
8 AWG minimum for -48/-60 VDC.
Connector accepts 8 AWG maximum.
Wire gauge for DC input power connections
1200 WMaximum power output
Table 3: AC Power Supply Specifications
A900-PWR1200-APart number
115VAC/ 230VACInput power specification
85/264 VACInput voltage
85 VACMinimum input voltage
264 VACMaximum input voltage
12VMinimum output voltage
12.4VMaximum output voltage
1200 WMaximum power output
For more information about installing the Cisco ASR 907 Router power supplies, see Installing the Power
Supply.
Redundancy
The Cisco ASR 907 Router chassis includes a slot for an optional redundant power supply. The redundant
power supply option provides a second power supply to ensure that power to the chassis continues uninterrupted
if one power supply fails or input power on one line fails. Redundancy is supported either with identical power
supplies or a combination of AC and DC power supply. The Cisco ASR 907 Router supports current sharing
between the power supplies.
If you install a redundant power supply on the Cisco ASR 907 Router, we recommend that you connect each
power supply to a separate input power source in order to ensure that the router maintains power in the event
of a power interruption caused by an electrical failure, a wiring fault, or a tripped circuit breaker.
Dying Gasp
The Cisco ASR 907 Router DC power supply does not support the Dying Gasp feature.
Status LEDs
LEDs are also provided on each power supply to indicate the status of the input power and the health of the
power supply. For more information about the LEDs on the Cisco ASR 907 Router, see Troubleshooting.
Fan Tray
The fan tray module supported on the router is:
Cisco ASR 907 Router Hardware Installation Guide
6
Cisco ASR 907 Router Overview
Redundancy

• A907-FAN-E
The fan tray has:
• Four dual rotor fans—for the PSU area cooling
• 12 fans (three columns for four fans)—60x60x38mm fans for the RSP and IM area
The fan tray has the following hardware features:
• It provides side-to-side forced air cooling
• It provides redundant fans
• It is field replaceable
• It contains status LEDs
For more information about air flow guidelines, see Air Flow Guidelines. For instructions on how to install
the fan tray, see Installing the Fan Tray . For a summary of the LEDs on the fan tray, see LED Summary .
Dust Filter (A907-FAN-F)
The dust filter on the fan tray is a quadrafoam 45PPI filter which is 85 percent dust resistant. For installing
the fan filter, see Removing and Replacing the Dust Filter section.
Air Plenum (A907-F2B-AIR-U)
Air Plenum or air baffle assembly is used to change the air flow pattern of the unit. When the router is installed
with the plenum, the air flow pattern is changed from side-side to front-back. The air flow front-back pattern
provides a rack installation bay with a cool front zone and hot rear zone. For installing the plenum, see
Installing the Chassis in the Air Plenum section.
When the air plenum and the fan filter are installed in the chassis, the system operating temperature is 55º C.
Note
RSP Modules
The Cisco ASR 907 Router is designed to use up to two RSP modules to handle the data plane, network timing,
and control plane functionalities for the router. The RSP configuration allows you to use Cisco IOS software
to control chassis management, redundancy, external management, and system status indications on the router.
RSP features include:
• Loading software onto processor-based interface modules
• Redundant RSP management—The RSP manages detection of RSPs, exchange of health and status
information, role negotiation, function for detection, health and status exchange, role negotiation
• Packet processing
• Traffic management, including buffering, queuing, and scheduling, Ethernet MAC functions
• Network clocking functions including phase and time-of-day for BITS, 1 PPS, 10 MHz, and 1588 PTP
clock references.
• Storage of software images, system configuration, SysLog
• PTP packet processing including IEEE 1588-2008 for recovering network timing (frequency, phase, and
time) from upstream PTP clocks, for generating PTP frequency and phase references as inputs to the
SETS, and for distributing them to downstream PTP clocks
Cisco ASR 907 Router Hardware Installation Guide
7
Cisco ASR 907 Router Overview
Dust Filter (A907-FAN-F)

• External management interfaces (RS232 console, management ENET, USB console, USB storage) and
system status LED indicators
Supported RSPs
Effective Cisco IOS-XE Release 3.16, the Cisco ASR 907 Router supports the following RSP:
• A900-RSP3C-400-W—Provides 8 GB of SDRAM, 20 Mb of TCAM memory on every ASIC.
The RSP does not provide external network interfaces for user traffic. All network interfaces are provided
through separate IMs.
Supported RSP Features
The RSP provides the following features on the Cisco router:
• Centralized data plane, timing, and control plane functions for the system
• High-level control of interface modules
• Management functionalities for the router
• Control plane (host) CPU and associated memory in which IOS-XE and platform control software runs
• Nonvolatile memory for storage of software images, configurations, and system files
• Enabling and monitoring the health and presence of fan trays, interface modules, and power supplies
• Field replacement and hot-swap capabilities
Swapping of Interface Modules
The following Ethernet interface modules support swapping on the Cisco A900-RSP3C-400-W module.
• 8-port Gigabit Ethernet SFP Interface Module (8X1GE)
• 8-port Gigabit Ethernet RJ45 (Copper) Interface Module (8X1GE)
• SFP Combo IM—8-port Gigabit Ethernet (8X1GE) + 1-port 10 Gigabit Ethernet (1X10GE)
• Copper Combo IM—8-port Gigabit Ethernet (8X1GE) + 1-port 10 Gigabit Ethernet Interface
Module(1X10GE)
• 2-port 10 Gigabit Ethernet Interface Module (2X10GE)
• 2-port 40 Gigabit Ethernet Interface Module (2X40GE)
• 1-port 100 Gigabit Ethernet Interface Module (1X100GE)
• 2-port 100 Gigabit Ethernet (QSFP) Interface Module (2X100GE)
• 1-Port OC-192 or 8-Port Low Rate CEM Interface Module
• 48 T1/E1 TDM Interface Module (48XT1/E1)
• 48 T3/E3 TDM Interface Module (48XT3/E3)
Use the hw-module subslot default command before performing a swap of the modules. to default the
interfaces on the interface module.
The hw-module subslot default command is not supported on the TDM and OC-3 interface modules.
Note
Cisco ASR 907 Router Hardware Installation Guide
8
Cisco ASR 907 Router Overview
Supported RSPs

Failure in executing the command may cause the interface to enter the Out of Service state. To recover from
out of service state, perform the following:
• Insert the original IM and execute the hw-module subslot 0/bay default command. Swap the module.
For more information, see Cisco IOS Interface and Hardware Component Command Reference.
• If the module does not come up, perform a reload of the router.
Supported Interface Modules
There are certain restrictions in using the interface modules on different slots in the chassis. Contact Cisco
Sales and Support for the valid combinations.
Note
Cisco ASR 907 Router Hardware Installation Guide
9
Cisco ASR 907 Router Overview
Supported Interface Modules

Table 4: A900-RSP3 Supported Interface Modules and Part Numbers
SlotPart NumberInterface ModulesRSP Module
0,1,2,5,6,9,10,13,14,15A900-IMA8S8-port Gigabit Ethernet SFP Interface
Module (8X1GE)
A900-RSP3C-400-W
0,1,2,5,6,9,10,13,14,15A900-IMA8T8-port Gigabit Ethernet RJ45 (Copper)
Interface Module (8X1GE)
Not SupportedA900-IMA1X1-port 10 Gigabit Ethernet XFP Interface
Module (1X10GE)
2,5,6,9,10,13,14,15ASR900-IMA8S1ZSFP Combo IM—8-port Gigabit Ethernet
(8X1GE) + 1-port 10 Gigabit Ethernet
(1X10GE)
2,5,6,9,10,13,14,15ASR900-IMA8T1ZCopper Combo IM—8-port Gigabit
Ethernet (8X1GE) + 1-port 10 Gigabit
Ethernet Interface Module (1X10GE)
3,4,7,8,11,12ASR900-IMA2Z2-port 10 Gigabit Ethernet Interface
Module (2X10GE)
Not SupportedA900-IMA16D16-port T1/E1 Interface Module
Not SupportedA900-IMASER14A/S14-port Serial Interface Module
Not SupportedA900-IMA8D8-port T1/E1 Interface Module
Not SupportedA900-IMA32D32-port T1/E1 Interface Module
7 and 8A900-IMA1C1x100G Interface module
7 and 81 A900-IMA2C2-port 100 Gigabit Ethernet (QSFP)
Interface Module (2X100GE)
3,4,7,8,11,12A900-IMA2F2x40G Interface module
3,4,7,8,11,12A900-IMA8Z2 8x10G Interface module
0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15A900-IMA8CS1Z-M8/16-port 1 Gigabit Ethernet (SFP/SFP) +
1-port 10 Gigabit Ethernet (SFP+) / 2-port
1 Gigabit Ethernet (CSFP) Interface
Module
3,4,7,8,11,12 (10 G Mode)
0,1,2,5,6,9,10,13,14,15 (5 G Mode)
A900-IMA8S1Z-CX1-port OC-192 or 8-Port Low Rate CEM
Interface Module
2,3,4,5,6,7,8,9,10,11,12,13,14,15A900-IMA48D-C48-port T1/E1 Interface module
2,3,4,5,6,7,8,9,10,11,12,13,14,15A900-IMA48T-C48-port T3/E3 Interface module
3,5,7,9,11,13,15A900-IMA3G-IMSG
Cisco ASR 907 Router Hardware Installation Guide
10
Cisco ASR 907 Router Overview
Supported Interface Modules