Cisco RMN302 User manual

User Guide
Wireless-N Broadband
Home Router
Model: RMN302
FPO
DRAFT - 6/25/201
0

i
Notice to Installers
The servicing instructions in this notice are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform
any servicing other than that contained in the operating instructions, unless you are qualified to do so.
Notice à l’attention des installateurs de réseaux câblés
Les instructions relatives aux interventions d’entretien, fournies dans la présente notice, s’adressent exclusivement au personnel
technique qualifié. Pour réduire les risques de chocs électriques, n’effectuer aucune intervention autre que celles décrites dans le mode
d’emploi et les instructions relatives au fonctionnement, à moins que vous ne soyez qualifié pour ce faire.
Note to System Installer
For this apparatus, the cable shield/screen shall be grounded as close as practical to the point of
entry of the cable into the building.For products sold in the US and Canada, this reminder is provided
to call the system installer's attention to Article 820-93 and Article 820-100 of the NEC (or Canadian
Electrical Code Part 1), which provides guidelines for proper grounding of the coaxial cable shield.
This symbol is intended to alert you that uninsulated voltage within this product may
have sufficient magnitude to cause electric shock.Therefore, it is dangerous to make any
kind of contact with any inside part of this product.
CAUTION: To reduce the risk of electric shock, do not
remove cover (or back). No user-serviceable parts inside.
Refer servicing to qualified service personnel.
WARNING
TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
This symbol is intended to alert you of the presence of important operating and
maintenance (servicing) instructions in the literature accompanying this product.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ÉLECTRIQUE
NE PAS OUVRIR
Remarque à l’attention de l’installateur du système
Avec cet appareil, le blindage/écran du câble doit être mis à la terre aussi près que possible du point
d’entrée du câble dans le bâtiment. En ce qui concerne les produits vendus aux États-Unis et au
Canada, ce rappel est fourni pour attirer l’attention de l’installateur sur les articles 820-93 et 820-100
du Code national de l’électricité (ou Code de l'électricité canadien, Partie 1) qui fournissent des lignes
directrices concernant la mise à la terre correcte du blindage (écran) du câble. coaxial
Ce symbole a pour but de vous prévenir que des tensions électriques non isolées
existent à l’intérieur de ce produit, pouvant être d’une intensité suffisante pour causer
des chocs électriques. Il est donc dangereux d'établir un contact quelconque avec l’une
des pièces comprises à l’intérieur de ce produit.
ATTENTION : Pour réduire les risques de chocs électriques,
ne pas enlever le couvercle (ou le panneau arrière). Ne
contient aucune pièce réparable par l’utilisateur. Confier les
interventions aux techniciens d’entretien qualifiés.
AVERTISSEMENT
POUR ÉVITER LES INCENDIES OU LES CHOCS ÉLECTRIQUES,
NE PAS EXPOSER L’APPAREIL À LA PLUIE OU À L’HUMIDITÉ.
Ce symbole a pour but de vous prévenir de la présence d’instructions importantes
relatives au fonctionnement ou à l’entretien (et aux réparations) dans la documentation
accompagnant ce produit.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
DANGER ÉLECTRIQUE
NE PAS OUVRIR
DRAFT - 6/25/201
0

ii
Mitteilung für CATV-Techniker
Die in dieser Mitteilung aufgeführten Wartungsanweisungen sind ausschließlich für qualifiziertes Fachpersonal bestimmt. Um die
Gefahr eines elektrischen Schlags zu reduzieren, sollten Sie keine Wartungsarbeiten durchführen, die nicht ausdrücklich in der
Bedienungsanleitung aufgeführt sind, außer Sie sind zur Durchführung solcher Arbeiten qualifiziert.
Aviso a los instaladores de sistemas CATV
Las instrucciones de reparación contenidas en el presente aviso son para uso exclusivo por parte de personal de mantenimiento
cualificado. Con el fin de reducir el riesgo de descarga eléctrica, no realice ninguna otra operación de reparación distinta a las contenidas
en las instrucciones de funcionamiento, a menos que posea la cualificación necesaria para hacerlo.
Mitteilung an den Systemtechniker
Für dieses Gerät muss der Kabelschutz/Schirm so nahe wie möglich am Eintrittspunkt des Kabels in
das Gebäude geerdet werden. Dieser Erinnerungshinweis liegt den in den USA oder Kanada
verkauften Produkten bei.Er soll den Systemtechniker auf Paragraph 820-93 und Paragraph 820-100
der US- Elektrovorschrift NEC (oder der kanadischen Elektrovorschrift Canadian Electrical Code Teil
1) aufmerksam machen, in denen die Richtlinien für die ordnungsgemäße Erdung des
Koaxialkabelschirms festgehalten sind.
Dieses Symbol weist den Benutzer auf das Vorhandensein von nicht isolierten
gefährlichen Spannungen im Gerät hin, die Stromschläge verursachen können. Ein
Kontakt mit den internen Teilen dieses Produktes ist mit Gefahren verbunden.
ACHTUNG: Zur Vermeidung eines Stromschlags darf die
Abdeckung (bzw. die Geräterückwand) nicht entfernt
werden. Das Gerät enthält keine vom Benutzer wartbaren
Teile. Wartungsarbeiten dürfen nur von qualifiziertem
Fachpersonal durchgeführt werden.
AVERTISSEMENT
DAS GERÄT NICHT REGEN ODER FEUCHTIGKEIT
AUSSETZEN, UM STROMSCHLAG ODER DURCH EINEN
KURZSCHLUSS VERURSACHTEN BRAND ZU VERMEIDEN
Dieses Symbol weist den Benutzer darauf hin, dass die mit diesem Produkt gelieferte
Dokumentation wichtige Betriebs- und Wartungsanweisungen für das Gerät enthält.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ACHTUNG
STROMSCHLAGGEFAHR,
NICHT ÖFFNEN
Nota para el instalador del sistema
En lo que se refiere a este aparato, el blindaje del cable debe conectarse a tierra lo más cerca
posible al punto por el cual el cable entra en el edificio. En el caso de los productos vendidos en los
EE. UU. y Canadá, el presente aviso se suministra para llamar la atención del instalador del sistema
sobre los Artículos 820-93 y 820-100 del NEC (o Código Eléctrico de Canadá, Parte 1), que
proporcionan directrices para una correcta conexión a tierra del blindaje del cable coaxial.
Este símbolo tiene como fin advertirle de que una tensión sin aislamiento en el interior
de este producto podría ser de una magnitud suficiente como para provocar una
descarga eléctrica. Por consiguiente, resulta peligroso realizar cualquier tipo de contacto
con alguno de los componentes internos de este producto.
ATENCIÓN: con el fin de reducir el riesgo de descarga
eléctrica, no retire la tapa (ni la parte posterior). No
existen en el interior componentes que puedan ser
reparados por el usuario. Encargue su revisión a
personal de mantenimiento cualificado.
ADVERTENCIA
PARAEVITARELRIESGO DEINCENDIOO DESCARGA
ELÉCTRICA, NO EXPONGA LA UNIDAD A LA LLUVIA O A LA
HUMEDAD.
Este símbolo tiene como fin alertarle de la presencia de importantes instrucciones de
operación y mantenimiento (revisión) contenidas en la literatura que acompaña al
producto.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATENCIÓN
RIESGO DE DESCARGA
ELÉCTRICA NO ABRIR
20080814_Installer800_Intl
DRAFT - 6/25/201
0

iii
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding-type plug has two blades and
a third grounding prong. The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as a power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
Power Source Warning
A label on this product indicates the correct power source for this product. Operate this product
only from an electrical outlet with the voltage and frequency indicated on the product label. If you
are uncertain of the type of power supply to your home or business, consult your service provider
or your local power company.
The AC inlet on the unit must remain accessible and operable at all times.
Ground the Product
WARNING: Avoid electric shock and fire hazard! If this product connects to coaxial cable
wiring, be sure the cable system is grounded (earthed). Grounding provides some protection
against voltage surges and built-up static charges.
Protect the Product from Lightning
In addition to disconnecting the AC power from the wall outlet, disconnect the signal inputs.
Verify the Power Source from the On/Off Power Light
When the on/off power light is not illuminated, the apparatus may still be connected to the power
source. The light may go out when the apparatus is turned off, regardless of whether it is still plugged
into an AC power source.
Eliminate AC Mains Overloads
WARNING: Avoid electric shock and fire hazard! Do not overload AC mains, outlets,
extension cords, or integral convenience receptacles. For products that require battery power
or other power sources to operate them, refer to the operating instructions for those products.
Provide Ventilation and Select a Location
•Remove all packaging material before applying power to the product.
•Do not place this apparatus on a bed, sofa, rug, or similar surface.
•Do not place this apparatus on an unstable surface.
•Do not install this apparatus in an enclosure, such as a bookcase or rack, unless the installation
provides proper ventilation.
•Do not place entertainment devices (such as VCRs or DVDs), lamps, books, vases with liquids, or
other objects on top of this product.
•Do not block ventilation openings.
Protect from Exposure to Moisture and Foreign Objects
WARNING: Avoid electric shock and fire hazard! Do not expose this product to
dripping or splashing liquids, rain, or moisture. Objects filled with liquids, such as vases,
should not be placed on this apparatus.
WARNING: Avoid electric shock and fire hazard! Unplug this product before cleaning.
Do not use a liquid cleaner or an aerosol cleaner. Do not use a magnetic/static cleaning device
(dust remover) to clean this product.
WARNING: Avoid electric shock and fire hazard! Never push objects through the
openings in this product. Foreign objects can cause electrical shorts that can result in
electric shock or fire.
Service Warnings
WARNING: Avoid electric shock! Do not open the cover of this product. Opening
or removing the cover may expose you to dangerous voltages. If you open the cover, your
warranty will be void. This product contains no user-serviceable parts.
Check Product Safety
Upon completion of any service or repairs to this product, the service technician must perform safety
checks to determine that this product is in proper operating condition.
Protect the Product When Moving It
Always disconnect the power source when moving the apparatus or connecting or disconnecting
cables.
Telephone Equipment Notice
When using your telephone equipment, basic safety precautions should always be followed to
reduce the risk of fire, electric stock and injury to persons, including the following:
1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry
tub, in a wet basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a
remote risk of electric shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
SAVE THESE INSTRUCTIONS
20090326_Modem No Battery_Safety
DRAFT - 6/25/201
0

iv
Cisco Wireless-N Broadband Home Router
Model: RMN302
Manufactured by:
Cisco Systems, Inc.
5030 Sugarloaf Parkway
Lawrenceville, Georgia 30044 USA
Telephone: [phone]
FCC Compliance
United States FCC Compliance
This device has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
such interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy. If not installed and used in accordance with the instructions, it may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment OFF and ON, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service provider or an experienced radio/television technician for help.
Any changes or modifications not expressly approved by Cisco Systems, Inc., could void the user’s
authority to operate the equipment.
The information shown in the FCC Declaration of Conformity paragraph below is a requirement of
the FCC and is intended to supply you with information regarding the FCC approval of this device.
The phone numbers listed are for FCC-related questions only and not intended for questions
regarding the connection or operation for this device. Please contact your service provider for
any questions you may have regarding the operation or installation of this device.
Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:
1) the device may not cause harmful interference, and 2) the device must accept any interference
received, including interference that may cause undesired operation.
Canada EMI Regulation
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.
FCC Part 68
The Federal Communications Commission (FCC) of the United States restricts specific uses of modems,
and places registration responsibilities on both the manufacturer and the individual user.
1. The modem may not be connected to a party line or to a coin-operated telephone.
2. Notification to the telephone company is no longer required prior to connecting registered equipment,
but upon request from the telephone company, the user shall tell the telephone company which line
the equipment is connected to as well as the registration number and ringer equivalence number of
the registered protective circuitry. FCC information is printed on a label on the bottom of the modem.
This equipment complies with Part 68 of FCC Rules and the requirements adopted by the ACTA. On
the base unit of this equipment is a label that contains, among other information, a product identifier in
the format US: GEMDL01BDDR2201V1. If requested, this number must be provided to the telephone
company.
The REN is useful to determine the quantity of devices you may connect to your telephone line and still
have those devices ring when your telephone number is called. In most, but not all areas, the sum of
the REN of all devices connected to one line should not exceed five (5.0). To be certain of the number
of devices you may connect to your line, as determined by the REN, you should contact your local
telephone company to determine the maximum REN for your calling area.
If your equipment causes harm to the telephone network, the telephone company may discontinue your
service temporarily. If possible, they will notify you in advance. If advance notice is not practical, you
will be notified as soon as possible. You will be informed of your right to file a complaint with the FCC.
Your telephone company may make changes in its facilities, equipment, operations or procedures that
could affect the proper functioning of your equipment. If they do, you will be notified in advance to give
you an opportunity to maintain uninterrupted telephone service.
If you experience trouble with this telephone equipment, please contact the service provider for
information on obtaining service or repairs.
The telephone company may ask that you disconnect this equipment from the network until the problem
has been corrected or until you are sure that the equipment is not malfunctioning.
This equipment may not be used on coin service provided by the telephone company. Connection to
party lines is subject to state tariffs.
IC (Industry Canada) Notice
Notice: The Industry Canada (formerly Canadian Department of Communications) label identifies
certified equipment. This certification means that the equipment meets certain telecommunications
network protective, operational, and safety requirements. The department does not guarantee the
equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection. In some cases, the company’s inside wiring associated with a
single-line individual service may be extended by means of a certified connector assembly (telephone
extension cord). The customer should be aware that compliance with the above conditions may not
prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user may give the
telecommunications company cause to request the user to disconnect the equipment. Users should
ensure for their own protection that the electrical ground connections of the power utility, telephone
lines and internal metallic water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or electrician, as appropriate.
Radiation Exposure Statements
Note: This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter. This equipment should be installed and operated with a minimum distance of 7.9 inches
(20 cm) between the radiator and your body.
US
This system has been evaluated for RF exposure for humans in reference to ANSI C 95.1 (American
National Standards Institute) limits. The evaluation was based on evaluation per ANI C 95.1 and FCC
OET Bulletin 65C rev 01.01. The minimum separation distance from the antenna to general bystander
is 7.9 inches (20 cm) to maintain compliance.
Canada
This system has been evaluated for RF exposure for humans in reference to ANSI C 95.1 limits. The
evaluation was based on evaluation per RSS-102 Rev 2. The minimum separation distance from the
antenna to general bystander is 7.9 inches (20 cm) to maintain compliance.
EU
This system has been evaluated for RF exposure for humans in reference to the ICNIRP (International
Commission on Non-Ionizing Radiation Protection) limits. The evaluation was based on the EN
50385 Product Standard to Demonstrate Compliance of Radio Base Stations and Fixed Terminals
for Wireless Telecommunications Systems with basic restrictions or reference levels related to
Human Exposure to Radio Frequency Electromagnetic Fields from 300 MHz to 40 GHz. The minimum
separation distance from the antenna to general bystander is 20 cm (7.9 inches).
Australia
This system has been evaluated for RF exposure for humans as referenced in the Australian
Radiation Protection standard and has been evaluated to the ICNIRP (International Commission
on Non-Ionizing Radiation Protection) limits. The minimum separation distance from the antenna to
general bystander is 20 cm (7.9 inches).
20090317 FCC DSL_Dom and Intl
DRAFT - 6/25/201
0

v
CE Compliance
Declaration of Conformity with
Regard to the EU Directive
1999/5/EC
(R&TTE Directive)
This declaration is only valid for configurations (combinations of software, firmware and hardware)
supported or provided by Cisco Systems for use within the EU. The use of software or firmware not
supported or provided by Cisco Systems may result in the equipment no longer being compliant
with the regulatory requirements.

[Bulgarian]         
  1999/5/.
esky
[Czech]:
Toto zaízení je v souladu se základními požadavky a ostatními odpovídajícími
ustanoveními Smrnice 1999/5/EC.
Dansk
[Danish]:
Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante
bestemmelser i Direktiv 1999/5/EF.
Deutsch
[German]:
Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren
entsprechenden Vorgaben der Richtlinie 1999/5/EU.
Eesti
[Estonian]:
See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele
sätetele.
English: This equipment is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Español
[Spanish]:
Este equipo cumple con los requisitos esenciales asi como con otras disposiciones
de la Directiva 1999/5/CE.

[Greek]:
           
    1999/5/EC.
Français
[French]:
Cet appareil est conforme aux exigences essentielles et aux autres dispositions
pertinentes de la Directive 1999/5/EC.
Íslenska
[Icelandic]:
Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar
1999/5/EC.
Italiano
[Italian]:
Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla
Direttiva 1999/5/CE.
Latviski
[Latvian]:
Š iekrta atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to
saisttajiem noteikumiem.
Lietuvi
[Lithuanian]:
Šis renginys tenkina 1999/5/EB Direktyvos esminius reikalavimus ir kitas šios
direktyvos nuostatas.
Nederlands
[Dutch]:
Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde
bepalingen van de Richtlijn 1999/5/EC.
Malti
[Maltese]:
Dan l-apparat huwa konformi mal-tiiet essenzjali u l-provedimenti l-ora rilevanti
tad-Direttiva 1999/5/EC.
Magyar
[Hungarian]:
Ez a készülék teljesíti az alapvet követelményeket és más 1999/5/EK irányelvben
meghatározott vonatkozó rendelkezéseket.
Norsk
[Norwegian]:
Dette utstyret er i samsvar med de grunnleggende krav og andre relevante
bestemmelser i EU-direktiv 1999/5/EF.
Polski
[Polish]:
Urzdzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami
okrelonymi Dyrektyw UE: 1999/5/EC.
Português
[Portuguese]:
Este equipamento está em conformidade com os requisitos essenciais e outras
provisões relevantes da Directiva 1999/5/EC.
Român
[Romanian] Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi
relevante ale Directivei 1999/5/EC.
Slovensko
[Slovenian]:
Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji
Direktive 1999/5/EC.
Slovensky
[Slovak]:
Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými
nariadeniami direktív: 1999/5/EC.
Suomi
[Finnish]:
Tämä laite täyttää direktiivin 1999/5/EY olennaiset vaatimukset ja on siinä
asetettujen muiden laitetta koskevien määräysten mukainen.
Svenska
[Swedish]:
Denna utrustning är i överensstämmelse med de väsentliga kraven och andra
relevanta bestämmelser i Direktiv 1999/5/EC.
Note: The full declaration of conformity for this product can be found in the Declarations of Conformity
and Regulatory Information section of the appropriate product hardware installation guide, which
is available on Cisco.com.
The following standards were applied during the assessment of the product against the requirements
of the Directive 1999/5/EC:
• Radio: EN 300 328
• EMC: EN 301 489-1 and EN 301 489-17
• Safety: EN 60950 and EN 50385
The CE mark and class-2 identifier is affixed to the product and its packaging. This product conforms
to the following European directives:
-1999/5/EC
National Restrictions
This product is for indoor use only.
France
For 2.4 GHz, the output power is restricted to 10 mW EIRP when the product is used outdoors in the
band 2454 - 2483,5 MHz. There are no restrictions when used in other parts of the 2,4 GHz band.
Check http://www.arcep.fr/ for more details.
Pour la bande 2,4 GHz, la puissance est limitée à 10 mW en p.i.r.e. pour les équipements utilisés en
extérieur dans la bande 2454 - 2483,5 MHz. Il n’y a pas de restrictions pour des utilisations dans
d’autres parties de la bande 2,4 GHz. Consultez http://www.arcep.fr/ pour de plus amples détails.
Italy
This product meets the National Radio Interface and the requirements specified in the National
Frequency Allocation Table for Italy. Unless this wireless LAN product is operating within the
boundaries of the owner’s property, its use requires a “general authorization.” Please check http://
www.comunicazioni.it/it/ for more details.
Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale
di ripartizione delle frequenze in Italia. Se non viene installato all ‘interno del proprio fondo, l’utilizzo di
prodotti Wireless LAN richiede una “Autorizzazione Generale”. Consultare http://www.comunicazioni.
it/it/ per maggiori dettagli.
Latvia
The outdoor usage of the 2.4 GHz band requires an authorization from the Electronic Communications
Office. Please check http://www.esd.lv for more details.
2,4 GHz frekven?u joslas izmantošanai ?rpus telp?m nepieciešama at?auja no Elektronisko sakaru
direkcijas. Vair?k inform?cijas: http://www.esd.lv.
Note: The regulatory limits for maximum output power are specified in EIRP. The EIRP level of a
device can be calculated by adding the gain of the antenna used (specified in dBi) to the output
power available at the connector (specified in dBm).
Antennas
Use only the antenna supplied with the product.
20090312 CE_Gateway
DRAFT - 6/25/201
0

vi
U.S. Patents
A patent notice is affixed to this product. In addition, the product
may also be covered by one or more of the following patents:
4,498,169, 4,692,919, 4,748,667; 4,829,569; 4,866,770; 4,885,775; 4,888,799; 4,890,319; 4,922,456;
4,922,532; 4,924,498; 4,965,534; 4,991,011; 5,003,384; 5,012,510; 5,029,207; 5,045,816; 5,053,883;
5,054,071; 5,058,160; 5,142,575; 5,142,690; 5,146,526; 5,155,590; 5,214,390; 5,225,902; 5,225,925;
5,235,619; 5,237,610; 5,239,540; 5,241,610; 5,247,364; 5,255,086; 5,257,403; 5,267,071; 5,270,809;
5,271,041; 5,272,752; 5,282,028; 5,285,497; 5,287,351; 5,301,028; 5,309,514; 5,317,391; 5,319,709;
5,341,425; 5,347,388; 5,347,389; 5,357,276; 5,359,601; 5,361,156; 5,367,571; 5,379,141; 5,379,145;
5,381,481; 5,390,337; 5,400,401; 5,406,558; 5,418,782; 5,420,866; 5,420,923; 5,425,101; 5,428,404;
5,430,568; 5,434,610; 5,436,749; 5,438,370; 5,440,632; 5,442,472; 5,455,570; 5,457,701; 5,471,492;
5,477,199; 5,477,262; 5,477,282 5,477,370; 5,481,389; 5,481,542; 5,485,221; 5,493,339; 5,497,187;
5,500,758; 5,502,499; 5,506,904; 5,519,780; 5,539,822; 5,550,825; 5,579,055; 5,579,057; 5,583,562;
5,592,551; 5,596,606; 5,600,378; 5,602,933; 5,640,388; 5,657,414; 5,675,575; 5,684,876; 5,715,515;
5,724,525; 5,734,822; 5,740,300; 5,742,677; 5,754,940; 5,757,416; 5,771,064; 5,774,859; 5,825,829;
5,826,167; 5,850,305; 5,854,703; 5,870,474; 5,892,607; 5,920,626; 5,923,755; 5,930,024; 5,930,515;
5,937,067; 5,963,352; 5,966,163; 5,982,424; 5,991,139; 5,999,207; 6,005,631; 6,005,938; 6,016,163;
6,028,941; 6,029,046; 6,052,384; 6,055,244; 6,072,532; 6,105,134; 6,148,039; 6,157,719; 6,188,729;
6,195,389; 6,212,278; 6,215,530; 6,219,358; 6,240,103; 6,243,145; 6,246,767; 6,252,964; 6,272,226;
6,292,081; 6,292,568; 6,320,131; 6,374,275; 6,405,239; 6,411,602; 6,417,949; 6,424,714; 6,424,717;
6,433,906; 6,438,139; 6,463,586; 6,467,091; 6,476,878; 6,493,876; 6,510,519; 6,516,002; 6,516,412;
6,526,508; 6,538,595; 6,546,013; 6,560,340; 6,567,118; 6,570,888; 6,622,308; 6,629,227; 6,664,984;
6,667,994; 6,671,879; 6,674,967; 6,678,891; 6,714,598; 6,721,352; 6,721,956; 6,725,459; 6,738,982;
6,744,892; 6,744,967; 6,751,271; 6,760,918; 6,795,972; 6,802,077; 6,804,708; 6,811,447; 6,817,028;
6,822,972; 6,823,385; 6,832,386; 6,845,106; 6,868,473; 6,874,075; 6,889,191; 6,909,471; 6,917,622;
6,917,628; 6,922,412; 6,927,806; 6,928,656; 6,931,058; 6,937,729; 6,969,279; 6,971,008; 6,971,121;
6,978,310; 6,986,156; 6,988,900; 6,996,838; 7,010,801; 7,053,960; 7,065,213; 7,069,578; 7,069572;
D348065; D354959; D359737; D363932; D390217; D434753; D507240; D507535; D513407;
D516518; RE36368; RE36988
20070417 Patents
Disclaimer
Cisco Systems, Inc. assumes no responsibility for errors or
omissions that may appear in this guide. We reserve the right to
change this guide at any time without notice.
Documentation Copyright Notice
Information in this document is subject to change without notice.
No part of this document may be reproduced in any form without
the express written permission of Cisco Systems, Inc.
Software and Firmware Use
The software described in this document is protected by copyright
law and furnished to you under a license agreement. You may only
use or copy this software in accordance with the terms of your
license agreement.
The firmware in this equipment is protected by copyright law. You
may only use the firmware in the equipment in which it is provided.
Any reproduction or distribution of this firmware, or any portion of
it, without our express written consent is prohibited.
DRAFT - 6/25/201
0

1
Table of Contents
Product Overview ............................................................................................................3
Front Panel............................................................................................................................................................................................3
Top Panel...............................................................................................................................................................................................4
Back Panel.............................................................................................................................................................................................5
Connecting to the Network...................................................................................................................................5
Placement Positions.....................................................................................................................................................................6
Wireless Security Checklist ...........................................................................................7
General Network Security Guidelines..........................................................................................................................8
Additional Security Tips............................................................................................................................................................8
Advanced Configuration .................................................................................................8
How to Access the Web-Based Utility..........................................................................................................................8
Setup > ADSL.....................................................................................................................................................................................9
Setup > ADSL (WAN Connection for PVC)............................................................................................................13
Setup > Ethernet...........................................................................................................................................................................16
Setup > Local Network ............................................................................................................................................................18
Setup > DDNS.................................................................................................................................................................................20
Setup > Advanced Routing .................................................................................................................................................21
Setup > PVC/VLAN Mapping............................................................................................................................................22
Wireless > Basic Settings.....................................................................................................................................................23
Wireless > Security....................................................................................................................................................................23
Wireless > MAC Filter...............................................................................................................................................................25
Wireless > Wi-Fi Protected Setup.................................................................................................................................25
Wireless > Advanced Settings.........................................................................................................................................27
Voice.......................................................................................................................................................................................................28
Voice > Info........................................................................................................................................................................................28
Voice > System..............................................................................................................................................................................30
Voice > User1/2 ............................................................................................................................................................................30
Storage > Disk Detail.................................................................................................................................................................31
Storage > Disk Management .............................................................................................................................................32
Security > Firewall.......................................................................................................................................................................32
Access Restrictions > Internet Access Policy.....................................................................................................33
Applications & Gaming > Single Port Forwarding ...........................................................................................34
Applications & Gaming > Port Range Forwarding...........................................................................................35
Applications & Gaming > DMZ .........................................................................................................................................35
Applications & Gaming > Port Range Triggering .............................................................................................36
Applications & Gaming > QoS ..........................................................................................................................................36
Applications & Gaming > Service ..................................................................................................................................39
Administration > Management.........................................................................................................................................40
Administration > Log.................................................................................................................................................................41
Administration > Diagnostic................................................................................................................................................42
Administration > Backup........................................................................................................................................................42
Administration > Factory Defaults.................................................................................................................................42
Administration > Upgrade....................................................................................................................................................43
Administration > Reboot........................................................................................................................................................43
Administration > Logout.........................................................................................................................................................43
Status > Internet............................................................................................................................................................................44
Status > Local Network............................................................................................................................................................44
Status > Wireless .........................................................................................................................................................................45
Status > DSL Connection......................................................................................................................................................45
Status > Bridges............................................................................................................................................................................46
Troubleshooting ............................................................................................................ 47
Specifications................................................................................................................ 48
Software License Agreement...................................................................................... 49
Software in Cisco Products ................................................................................................................................................49
Software Licenses.......................................................................................................................................................................49
DRAFT - 6/25/201
0

2
DRAFT - 6/25/201
0

3
Product Overview
Thank you for choosing the Cisco®Wireless-N Broadband Home Router. The Router
lets you access the Internet via a wireless connection or through one of its four (or five)
switched ports.
You can also use the Router to share resources such as computers and storage. Various
security features help to protect your data and your privacy while you are online. Security
features include WPA2 security, a Stateful Packet Inspection (SPI) firewall, and NAT
technology. Configuring the Router is easy using the provided browser-based utility.
Front Panel
Power (Green/Red) The Power LED lights up when the Router is powered on. It
flashes during the self-test. The LED becomes red during a malfunction.
Internet (Green/Red)The Internet LED lights up when the Router is connected to the
Internet. It flashes to indicate network activity over the Internet port. The LED
becomes red when the Internet connection fails.
WAN (Green) The WAN LED corresponds with the WAN port and serves two
purposes. If the LED is continuously lit, the Router is successfully connected
to a device through that port. It flashes to indicate network activity over that
port.
WAN MOCA (Green) Text TBD
LAN MOCA (Green)Text TBD
LAN 1-4 (Green) These numbered LEDs, corresponding with the numbered Ethernet
ports on the Router’s back panel, serve two purposes. If the LED is
continuously lit, the Router is connected to a device through that port. It
flashes to indicate network activity over that port.
WLAN (Green) The WLAN LED lights up when the wireless feature is enabled.
It flashes when the Router is sending or receiving data over the wireless
network.
USB 1 (Green) The USB LED lights up when the Router is connected to a device
and 2 through the USB port. It flashes to indicate USB activity.
WPS (Green/Red) The WPS LED lights up when wireless security is enabled. It
flashes during the Wi-Fi Protected Setup process. The LED becomes red
when wireless security is disabled.
FPO
DRAFT - 6/25/201
0

4
Top Panel
Wi-Fi Protected If you have a client device, such as a wireless adapter, that supports
Setup Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup to
automatically configure wireless security for your wireless network(s).
Note: Wi-Fi Protected Setup can only be used for the default wireless
network. (The Router supports up to four wireless networks. The other
three can be configured using the Router’s web-based utility.)
Follow the appropriate instructions:
Method #1
Use this method if your client device has a Wi-Fi Protected Setup button.
1. Click or press the Wi-Fi Protected Setup button on the client device. (If Wi-Fi Protected
Setup is an on-screen option, then select it.)
2. Click the Wi-Fi Protected Setup button on the top panel of the Router.
3. After the client device has been configured, refer back to your client device or its
documentation for further instructions.
Method #2
Use this method if your client device has a Wi-Fi Protected Setup PIN number.
1. Access the Router’s web-based utility.
2. Click the Wireless tab.
3. Click the Wi-Fi Protected Setup tab
4. Enter the client PIN number in the PIN field on this screen (the Router’s Wi-Fi Protected
Setup screen).
5. Click Register.
Method #3
Use this method if your client device asks for the Router’s PIN number.
1. Enter the PIN number listed on the label on the bottom of the Router.
2. After the client device has been configured, refer back to your client device or its
documentation for further instructions.
Note: Wi-Fi Protected Setup configures one client device at a time. Repeat the instructions
for each client device that supports Wi-Fi Protected Setup.
FPO
DRAFT - 6/25/201
0

5
Back Panel
Reset There are two ways to reset the Router’s settings to factory defaults.
Either press and hold the Reset button for approximately ten seconds, or
restore the defaults from the Administration > Factory Defaults screen of
the Router’s web-based utility.
Note:The reset does not restore the voice settings to the factory defaults.
WPS Text TBD
USB The USB port connects to a USB storage device, such as a USB hard drive
or flash disk.
Ethernet These Ethernet ports (1, 2, 3, 4) connect the Router to wired computers
LAN 1-4 and other Ethernet network devices.
F Connector Text TBD
Ethernet The WAN/LAN5 port can act as a Wide Area Network (WAN) or Local Area
WAN/LAN5 Network (LAN) port. As a WAN port, it connects to a broadband modem.
As a LAN port, it connects to a wired computer or other Ethernet network
device.
Connecting to the Network
1. Use a coaxial cable to connect the F-Conn port on the RMN302 to the
wall connector or to the coaxial network used to distribute IP data.
2. Use an Ethernet cable to connect the LAN port on the RMN302 to your
home network or to a PC.
3. Attach the power adapter to the POWER port on the back of the
RMN302, and plug it into a wall outlet.
4. Turn on the power switch.
FPO
T14758
FPO
PC or
Home Network
Coaxial Network Set-Top Box
To Wall
Outlet
V
O
L
U
M
E
C
H
A
N
N
E
L
TV Guide Record
CISCO8455DVB
DRAFT - 6/25/201
0

6
Placement Positions
There are two ways to physically install the Router. The first way is to place the Router
horizontally on a surface. The second way is to mount the Router on a wall.
Horizontal Placement
The Router has four rubber feet on its bottom panel. Place the Router on a level surface
near an electrical outlet.
Wall-Mounting Placement
The Router has four wall-mount slots on its bottom panel. The distance between two
adjacent slots is 54 mm (2.13 inches).
Two screws are needed to mount the Router.
Suggested Mounting Hardware
2.5 to 3.0 mm
4 to 5 mm 1 to 1.5 mm
Note: Mounting hardware illustrations are not true to scale.
Note: Cisco is not responsible for damages incurred by insecure wall-mounting hardware.
Follow these instructions:
1. Determine where you want to mount the Router. Make sure that the wall you use is smooth,
flat, dry, and sturdy. Also make sure the location is within reach of an electrical outlet.
2. Drill two holes into the wall. Make sure the holes are 54 mm (2.13 inches) apart.
3. Insert a screw into each hole and leave 2 mm (0.8 inches) below the head exposed.
4. Maneuver the Router so two of the wall-mount slots line up with the two screws.
5. Place the wall-mount slots over the screws and slide the Router down until the screws fit
snugly into the wall-mount slots.
Note: To safely wall-mount the Router, the side panel with the antenna must face upward.
54 mm
Print this page at 100% size. Cut along the dotted
line, and place on the wall to drill precise spacing.
Wall Mounting Template
DRAFT - 6/25/201
0

7
Wireless Security Checklist
Wireless networks are convenient and easy to install, so homes with high-speed Internet
access are adopting them at a rapid pace. Because wireless networking operates by
sending information over radio waves, it can be more vulnerable to intruders than a
traditional wired network. Like signals from your cellular or cordless phones, signals from
your wireless network can also be intercepted. Since you cannot physically prevent
someone from connecting to your wireless network, you need to take some additional
steps to keep your network secure.
1. Change the default wireless network name or SSID
Wireless devices have a default wireless network name or Service Set Identifier (SSID) set
by the factory. This is the name of your wireless network, and can be up to 32 characters
in length. Cisco wireless products use cisco as the default wireless network name. You
should change the wireless network name to something unique to distinguish your
wireless network from other wireless networks that may exist around you, but do not use
personal information (such as your Social Security number) because this information may
be available for anyone to see when browsing for wireless networks.
2. Change the default password
For wireless products such as access points, routers, and gateways, you will be asked for a
password when you want to change their settings. These devices have a default password
set by the factory. The Cisco default password is admin. Hackers know these defaults and
may try to use them to access your wireless device and change your network settings. To
thwart any unauthorized changes, customize the device’s password so it will be hard to
guess.
3. Enable MAC address filtering
Cisco routers and gateways give you the ability to enable Media Access Control (MAC)
address filtering. The MAC address is a unique series of numbers and letters assigned to
every networking device. With MAC address filtering enabled, wireless network access is
provided solely for wireless devices with specific MAC addresses. For example, you can
specify the MAC address of each computer in your home so that only those computers can
access your wireless network.
4. Enable encryption
Encryption protects data transmitted over a wireless network. Wi-Fi Protected Access
(WPA/WPA2) and Wired Equivalency Privacy (WEP) offer different levels of security for
wireless communication.
A network encrypted with WPA/WPA2 is more secure than a network encrypted with WEP,
because WPA/WPA2 uses dynamic key encryption. To protect the information as it passes
over the airwaves, you should enable the highest level of encryption supported by your
network equipment.
WEP is an older encryption standard and may be the only option available on some older
devices that do not support WPA.
DRAFT - 6/25/201
0

8
General Network Security Guidelines
Wireless network security is useless if the underlying network is not secure.
•Password protect all computers on the network and individually password protect
sensitive files.
•Change passwords on a regular basis.
•Install anti-virus software and personal firewall software.
•Disable file sharing (peer-to-peer). Some applications may open file sharing without
your consent and/or knowledge.
Additional Security Tips
•Keep wireless routers, access points, or gateways away from exterior walls and
windows.
•Turn wireless routers, access points, or gateways off when they are not being used (at
night, during vacations).
•Use strong passphrases that are at least eight characters in length. Combine letters
and numbers to avoid using standard words that can be found in the dictionary.
Web: For more information on wireless security, visit www.linksysbycisco.com/security
Advanced Configuration
To configure the Router, use its web-based utility. This chapter describes each web page
of the utility and each page’s key functions. You can access the utility via a web browser on
a computer connected to the Router.
Note: If your service provider supplied you with the Router, then it may be pre-configured
for you, and you will not need to make any changes. Contact your service provider for more
information.
The web-based utility has these main tabs: Setup, Wireless, Storage, Security, Parental
Control, Applications & Gaming, Administration, Status, and Advanced. Additional tabs will
be available after you click one of the main tabs.
How to Access the Web-Based Utility
To access the web-based utility, launch the web browser on your computer, and enter the
Router’s default IP address, 192.168.1.1, in the Address field. Then, press Enter.
A login screen appears. The first time you open the web-based utility, use the default user
name and password, admin and password. (You can set a new user name and password
from the Administration tab’s Management screen.) Click OK to continue.
Note: If the Router was supplied by your service provider, then it may restrict access to the
web-based utility. Contact your service provider for the login information.
Login Screen
DRAFT - 6/25/201
0

9
Setup > Interface
WAN Interface Setup
WAN Connection Settings
Network Type: Choose your WAN interface type from the dropdown list. Options include
Auto-Detection, MoCA, and Ethernet.
•Auto Detection: The router detects physical interface automatically and determine
the connection type. The detect result is displayed in “Current Network” field;
•MoCA: You can manually configure MoCA connection as physical interface.
•Ethernet: You can manually configure the layer 2 network as Ethernet WAN connection
Current Network: Indicates whether the current WAN connection is MoCA or Ethernet
WAN, and whether the connection is manually configured or auto-detected.
Ethernet WAN settings
Set Connection Shaping: Choose whether you want the router to smooth the ethernet
bandwidth. Options include No Shaping, Auto(link speed) and Manual.
MoCA WAN settings
Channel: Allow the router to detect an available frequency for your MoCA WAN, or choose
a channel frequency.
Node Type: Allow the router to detect your node type, or choose the correct option.
Auto-Detect privacy: Choose this option if you want to enable privacy auto detection.
MoCA Privacy: Choose this option if you want to enable privacy on your MoCA WAN
connection.
Password: If you chose to enable privacy on your MoCA WAN, enter your password here.
Power Limit: Allow the router to set the limit for the transmission power on your MoCA
WAN, or choose a percentage of power to use as a limit.
MoCA LAN Setup
MoCA LAN Settings
Channel: Allow the router to detect an available frequency for your MoCA LAN, or choose
a channel frequency.
MoCA Privacy: Choose this option if you want to enable privacy on your MoCA LAN
connection.
Password: If you chose to enable privacy on your MoCA LAN, enter your password here.
Power Limit: Allow the router to set the limit for the transmission power on your MoCA
WAN, or choose a percentage of power to use as a limit.
Setup > Interface
DRAFT - 6/25/201
0

10
Setup > Internet
WAN Connection Settings
Network Type: Choose your network type. Connection Type
Auto Detection Settings
Auto Detect Connection: Allows you to enable or disable internet connection type auto
detection.
Protocol Detection: Select this checkbox if you want the router to detect the internet connection
continuously, as defined by the Auto Detection Interval.
Auto Detection Interval: Specify how often the router should detect the internet connection (if
you chose Protocol Detection).
Ethernet WAN Setup
Connection Type: Choose whether your WAN uses IPoE (including DHCP and static IP) or
PPPoE.
IPoE Settings
IPoE Connection: Need text.
Gateway Probing: Choose whether you want to probe the gateway if the gateway is alive. Select
ARP to resolve MAC address by default.
Probing Using Unicast: Choose whether you want to ping the gateway with an ICMP request.
Probing Only on Idle: Choose whether you want to restrict probing if traffic is going through
router.
Probing Interval: Specify your probing interval, in seconds.
Probing Reset Trigger: Specify how long the probe should run before resetting the connection
Setup > Internet
DRAFT - 6/25/201
0

11
PPPoE Settings for PPPoE (RFC2516)
Primary (Required) and Secondary (Optional) DNS Enter the DNS (Domain Name System)
server IP address(es) provided by your service provider. At least one is required.
Username and Password Enter the Username and Password provided by your service
provider.
Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection
after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection
has been terminated due to inactivity, Connect on Demand enables the Router to automatically
re-establish your connection as soon as you attempt to access the Internet again. To use this
option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes
you want to have elapsed before your Internet connection terminates. The default Max Idle Time
is 5minutes.
Keep Alive If you select this option, the Router will periodically check your Internet connection.
If you are disconnected, then the Router will automatically re-establish your connection. To use
this option, select Keep Alive.
Setup > ADSL (WAN Connection for PVC) >
PPPoE (RFC2516)
DRAFT - 6/25/201
0

12
Setup > Local Network
Configure the Router’s Local Area Network (LAN) settings on this screen.
There are two views available, Basic and Advanced. The default view is Basic. To display the
Advanced View, click Advanced View. To return to the Basic View, click Basic View.
Local Network
The Local Network section changes the settings on the network connected to the Router’s
Ethernet ports. Wireless setup is performed through the Wireless tab.
Router IP
The values for the Router’s local IP Address and Subnet Mask are displayed. In most cases,
keeping the default values will work.
IP Address The default value is 192.168.1.1.
Subnet Mask The default value is 255.255.255.0.
Network Address Server Settings (DHCP)
The settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP)
server function. The Router can be used as a DHCP server for your network. A DHCP server
automatically assigns an IP address to each computer on your network. If you choose to enable
the Router’s DHCP server option, make sure there is no other DHCP server on your network.
DHCP Server A Dynamic Host Configuration Protocol (DHCP) server automatically assigns
an IP address to each computer on your network for you. Unless you already have one, Cisco
recommends that you keep the default, Enabled.
DHCP Options To configure DHCP options (available if DHCP is enabled), click this option. A
new window appears.
DHCP Option
•DHCP Option Select the appropriate setting.
•DHCP Option Value Enter the appropriate IP address, which is stored as a binary string
on the Router. (No check is performed on these values.)
Click Save Settings to apply your changes, or click Go Back to cancel your changes and
return to the Local Network screen.
Conditional Serving To configure the Conditional Serving Pool settings (available if DHCP is
enabled), click this option. A new window appears.
Setup > Local Network (Advanced View)
Setup > Local Network > DHCP Option
DRAFT - 6/25/201
0

13
Conditional Serving
Conditional Serving Pool
Enable DHCP Conditional Serving To enable this option, select the check box.
Otherwise, leave the check box blank.
For each entry, the table lists the following: MAC Address, Vendor Class ID, User Class ID,
Client ID, Host Name, Domain Name, IP Address, Precedence, and Action. To delete an
entry, click Delete. To configure the DHCP options for an entry, click DHCP Option.
Conditional Serving Entry
Precedence Enter the Precedence value. A lower value indicates higher priority.
MAC Address Enter the MAC Address, if applicable as a filter condition.
Vendor Class ID Enter the Vendor Class ID, if applicable as a filter condition.
User Class ID Enter the User Class ID, if applicable as a filter condition.
Client ID Enter the Client ID, if applicable as a filter condition. This field accepts ASCII or
hexadecimal strings. To enter a hexadecimal string, add Ox before the string.
Host Name Enter the Host Name, if applicable as a filter condition.
Domain Name If there is a match, the DHCP server will assign this Domain Name to the
host.
IP Address If there is a match, the DHCP server will assign this IP Address to the host.
Click Add Entry to add a new entry to the table. Click Save Settings to apply your changes.
Click Back to LAN Setup to return to the Local Network screen.
Starting IP Address Enter a value for the DHCP server to start with when issuing IP addresses.
Because the Router’s default IP address is 192.168.1.1, the Starting IP Address must be
192.168.1.2 or greater, but smaller than 192.168.1.253. The default is 192.168.1.64.
Ending IP Address Specify the final IP address of the range available for assignment. The
default is 192.168.1.253.
Client Lease Time The Client Lease Time is the amount of time a network device will be allowed
connection to the Router with its current dynamic IP address. Enter the number of minutes
that the device will be “leased” this dynamic IP address. After the time is up, the device will be
automatically assigned a new dynamic IP address. The default is 1440 minutes.
DNS Proxy (Advanced View) The Domain Name System (DNS) is how the Internet translates
domain or website names into Internet addresses or URLs. To use DNS Proxy, keep the default,
Enable. Otherwise, select Disable.
Static DNS 1-3 (Advanced View) These entries are valid only when the DNS Proxy option is
disabled. At least one DNS server IP address is provided by your service provider. You can
enter up to three DNS server IP addresses here. The Router will use these for quicker access to
functioning DNS servers.
WINS (Advanced View) The Windows Internet Naming Service (WINS) converts NetBIOS
names to IP addresses. If you use a WINS server, enter that server’s IP address here. Otherwise,
leave this field blank.
Domain Name (Advanced View) Enter the Domain Name of your local network.
Reserved IP List (Advanced View) Enter the IP addresses you want to reserve, so they will not
be leased to DHCP clients.
Setup > Local Network > Conditional Serving
DRAFT - 6/25/201
0