Cisco IAD2435-8FXS User manual

QUICK START GUIDE
Cisco IAD2430 Series Integrated Access Devices
INCLUDING LICENSE AND WARRANTY
1Cisco 90-Day Limited Hardware Warranty Terms
2Obtaining Documentation and Submitting a Service Request
3Equipment, Tools, and Accessories
4Product Serial Number Location
5Accessibility
6Safety Information
7Installing the Chassis
8Installing a WAN or Voice Interface Card
9Connecting Cables
10 Powering On the Cisco IAD
11 Performing the Initial Configuration

2
1 Cisco 90-Day Limited Hardware Warranty Terms
The following are special terms applicable to your hardware warranty. Your formal Warranty Statement, including the warranty
applicable to Cisco software, appears in the Cisco Information Booklet that accompanies your Cisco product.
Duration of Hardware Warranty: Ninety Days
Replacement, Repair or Refund Procedure for Hardware: Cisco or its service center will use commercially reasonable efforts to
ship a replacement part within ten (10) working days after receipt of the RMA request. Actual delivery times may vary
depending on Customer location.
Cisco reserves the right to refund the purchase price as its exclusive warranty remedy.
To Receive a Return Materials Authorization (RMA) Number: Please contact the party from whom you purchased the product.
If you purchased the product directly from Cisco, contact your Cisco Sales and Service Representative.
Complete the information below, and keep it for reference:
2 Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the
monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be
delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS
version 2.0.
3 Equipment, Tools, and Accessories
This section describes the equipment, tools, and accessories that accompany or are not included with your router.
Products in the Cisco IAD2430 Series IADs
The Cisco IAD2430, Cisco IAD2431, and Cisco IAD2432 series Integrated Access Devices (IADs) (routers) consist of five
models with a common front panel (Figure 1); the front panel is labeled Cisco IAD2400 Series for these models. The
Cisco IAD2435 series router consists of one model (Cisco IAD2435-8FXS IAD) with a front panel that is different from the
front panel on other Cisco IAD2430 series routers (Figure 2). The Cisco IAD2430, Cisco IAD2431, and Cisco IAD2432 series
routers include a slot for the external flash memory card, as well as console, auxiliary, and flash memory (CF) ports. The IAD
back panels, labeled by specific model number, vary considerably, depending on interfaces, ports, and options. The analog voice
ports use an RJ-21 interface.
Product purchased from
Their telephone number
Product model and serial number
Maintenance contract number

3
Figure 1 Cisco IAD2430 Series Front Panel (Cisco IAD2432-24FXS IAD shown)
Figure 2 Cisco IAD2435 IAD Front Panel
Figure 3 identifies the different back panels and features of the Cisco IAD2430 series models. Figure 4 shows the back panel
and features of the Cisco IAD2432-24FXS IAD model. Figure 5 shows the back panel and features of the Cisco IAD2435-8FXS
IAD model.
Note Not all models have all functions.
88839
CISCO IAD2400
231872
Cisco IAD2400 SERIES
OK 0/0 0/1
FE T1/E1 FXS
CD AL 2/0 2/1 2/2 2/3 2/4 2/5 2/6 2/7

4
Figure 3 Back Panels for the Cisco IAD2430 Series Models
Cisco IAD2430-24FXS IAD
•RJ-21 analog voice
interface
•T1/E1 ports: none
•FE ports: 2
•External flash
memory
Cisco IAD2431-8FXS IAD
•RJ-21 analog voice
interface
•T1/E1 ports: 1
•FE ports: 1
•WIC/VIC option
•External flash
memory
Cisco IAD2431-16FXS IAD
•RJ-21 analog voice
interface
•T1/E1 ports: 1
•FE ports: 2
•WIC/VIC option
•External flash
memory
Cisco IAD2431-1T1E1 IAD
•T1/E1 ports: 2
•FE ports: 2
•WIC/VIC option
•External flash
memory
88838
VG224-24FXS
88825
IAD2431-8FXS
88826
IAD2431-16FXS
88827
IAD2431-1T1E1

5
Figure 4 Back Panel Function Options (Cisco IAD2432-24FXS IAD shown)
Note The console port is above the auxiliary port.
Cisco IAD2432-24FXS IAD
•RJ-21 analog voice
port
•T1/E1 ports: 2
•FE ports: 2
•WIC/VIC option
•External flash
memory
Cisco IAD2435-8FXS IAD
•RJ-21 analog voice
port
•T1/E1 ports: 1
•FE ports: 2
1Chassis ground connection 2RJ-21 connector 3T1/E1 port 1
4T1/E1 port 0 5Flash memory port 6WIC/VIC slot
7Fast Ethernet port 1 8Fast Ethernet port 0 9AUX port
10 Console port 11 DC power input 12 On/off switch
13 AC power input
88824
231873
IAD2435-8FXS
12V DC SA
CONSOLE
AUX
FastEthernet
WAN
0/1 0/0
T1/E1
FXS
88828
2
1
34
7
6
589
10
11 12
13

6
Figure 5 Back Panel Function Options (Cisco IAD2435-8FXS IAD shown)
Items Included with Cisco IAD2430, Cisco IAD2431, and Cisco IAD2432 IADs
The following items are included with each Cisco IAD2430, Cisco IAD2431, and Cisco IAD2432 IAD:
•Rack-mount brackets for 19-inch rack; grounding lug and fasteners; power cord
•NEBS grounding kit (Cisco IAD2432-24FXS)
•Connected RJ-45-to-DB9 cable (labeled Console)
•Connected RJ-45-to-DB-25 cable (labeled Auxiliary)
Note The rack-mount brackets for a 19-inch rack, the NEBS grounding kit, and the chassis guard for wall-mounting
applications are not included with the Cisco IAD2435-8FXS IAD.
Note Power cords vary, depending upon local requirements.
Items Included with Cisco IAD2435 IADs
The following items are included with the Cisco IAD2435 IAD:
•Connected RJ-45-to-DB9 cable (labeled Console)
•Power cord
4 Product Serial Number Location
The serial number label for most of the Cisco IAD2430 series routers is located on the bacj of the chassis at the bottom, near
the compliance label. The serial number label for the Cisco IAD2435 integrated access device is located on the bottom of the
chassis. The serial number label is 0.25 x 1 inch (6.35 x 25.4 mm). It has the letters “SN:” followed by eleven characters.
1
RJ-21 connector
2
T1/E1 WAN uplink
3
Fast Ethernet port 1, Fast
Ethernet port 0
4
Serial port—console or
auxiliary 5
Power connector
6
On/off switch
7Chassis ground connection 8Kensington security slot
231879
IAD2435-8FXS
12V DCSA
CONSOLE
AUX
FastEthernet
WAN
0/1 0/0
T1/E1
FXS
1
7
23
6
8
45

7
5 Accessibility
This product family uses a command-line interface (CLI). Because it is text based and relies on a keyboard for navigation, the
CLI is 508 conformant. All functions of the router can be configured and monitored through the CLI.
To view Cisco accessibility guidelines and product adherence, see Cisco Accessibility Products at the following URL:
http://www.cisco.com/web/about/responsibility/accessibility/products
6 Safety Information
The following warnings apply to the Cisco IAD2430 series IADs and should be read before installing this product.
For safety information that you need to know before working on your Cisco IAD2430 series IAD and for full translations of
the warnings in this document, see the Cisco IAD2400 Series Regulatory Compliance and Safety Information document at the
following URL:
http://www.cisco.com/en/US/docs/routers/access/iad2400/hardware/rcsi/2400rcsi.html
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any
equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for
preventing accidents. Use the statement number provided at the end of each warning to locate its translation in
the translated safety warnings that accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
Warning Only trained and qualified personnel should be allowed to install or replace this equipment. Statement 1030
Warning Do not work on the system, or connect or disconnect cables during periods of lightning activity. Statement 1001
Warning Read the installation instructions before connecting the system to the power source. Statement 1004
Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the
protective device is rated not greater than:
120 VAC, 15A (240 VAC, 10A international) Statement 1005
Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage
(TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports
both use RJ-45 connectors. Use caution when connecting cables. Statement 1021
Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To
avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away
from the unit first. Statement 1026
Warning This equipment has been designed for connection to TN and IT power systems. Statement 1007

8
Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Statement
1003
Warning To prevent accidental discharge in the event of a power line cross, route on-premise wiring away from power
cables and off-premise wiring, or use a grounded shield to separate the on-premise wiring from the power cables
and off-premise wiring. A power line cross is an event, such as a lightning strike, that causes a power surge.
Off-premise wiring is designed to withstand power line crosses. On-premise wiring is protected from power line
crosses by a device that provides overcurrent and overvoltage protection. Nevertheless, if the on-premise wiring
is in close proximity to, or not shielded from, the off-premise wiring or power cables during a lightning strike or
power surge, the on-premise wiring can carry a dangerous discharge to the attached interface, equipment, and
nearby personnel. Statement 338
Warning For connections outside the building where the equipment is installed, the following ports must be connected
through an approved network termination unit with integral circuit protection.
FXS/T3/E3 Statement 1044
Warning This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage. Do not touch the
RJ-11 (phone) port wires (conductors), the conductors of a cable connected to the RJ-11 port, or the associated
circuit-board when the ringer is active. The ringer is activated by an incoming call. Statement 1042
Warning This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect the host to
earth ground during normal use. Statement 242
Warning The importance of proper grounding cannot be overemphasized. It will minimize the potential for damage to your
system and maximize safety at the system site. We recommend you consult a licensed electrician or your local
electric utility company if you have any questions. Statement 269
Warning A ground wire must always be a single piece of wire. Never splice two wires together for a ground. Corrosion and
weathering can lead to a poor connection at the splice, making the ground ineffective and dangerous.
Statement
270
Warning This unit is intended to be mounted on a wall. Please read the wall mounting instructions carefully before
beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a
hazardous situation to people and damage to the system. Statement 248
Warning AC connected units must have a permanent ground connection in addition to the power cable ground wire.
NEBS-compliant grounding satisfies this requirement. Statement 284
Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure
that the system remains stable. The following guidelines are provided to ensure your safety:
This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

9
When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the
bottom of the rack.
If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.
Statement 1006
Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions. Statement 1015
Warning Take care when connecting units to the supply circuit so that wiring is not overloaded. Statement 1018
Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only
through the use of a special tool, lock and key, or other means of security. Statement 1017
Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of
a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if
you are uncertain that suitable grounding is available. Statement 1024
Warning Use copper conductors only. Statement 1025
Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages
and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other
equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards,
faceplates, front covers, and rear covers are in place. Statement 1029
Warning Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement, or near a swimming pool. Statement 1035
Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement
1036
Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the
network interface. Statement 1037
Warning Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of
electric shock from lightning. Statement 1038
Warning To report a gas leak, do not use a telephone in the vicinity of the leak. Statement 1039

10
Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040
Warning Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network
voltages. Statement 1041
Warning This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260. Incorrectly
connecting this equipment to a general-purpose outlet could be hazardous. The telecommunications lines must be
disconnected 1) before unplugging the main power connector or 2) while the housing is open, or both.
Statement
1043
Warning No user-serviceable parts inside. Do not open. Statement 1073
Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074
7 Installing the Chassis
This section provides the procedures for installing the chassis.
Chassis Installation Options
You can set the chassis on a desktop, install it in a rack, or mount it on a wall.
Tip Before proceeding, consider the location of the equipment with respect to a good ground. See the “Grounding the
Chassis” section on page 18.
See the following instructions:
•Using the Correct Bracket Screws, page 10
•Using Rack-Mount Brackets, page 11
•Rack-Mounting the Chassis, page 12
•Setting the Chassis on a Desktop, page 13
•Setting the Cisco IAD2435 on a Desktop, page 13
•Wall-Mounting the Chassis, page 13
•Grounding the Chassis, page 18
•Connecting the RJ-21 Cable in the Velcro Harness, page 23
Caution Use only the mounting hardware supplied with this product.
Using the Correct Bracket Screws
Two sets of bracket attachment screws are provided, in separate packages. Take care to use each screw type, and washers as
needed, in the appropriate locations. Table 1 summarizes the bracket attachment screw types for the Cisco IAD2430,
Cisco IAD2431, and Cisco IAD2432 IADs.