Cisco Internet Router Cisco 12404 User manual

Corporate Headquarters:
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Cisco 12404 Internet Router
Unpacking Instructions
Product Number: GSR4-PKG=
This document gives you instructions for unpacking and repackaging the
Cisco 12404 Internet Router. It includes:
•Tools and Equipment, page 2
•Unpacking the Cisco 12404 Internet Router, page 3
•Repackaging the Cisco 12404 Internet Router, page 9
•Transporting a Cisco 12000 Series Router, page 11
•Obtaining Documentation, page 11
•Documentation Feedback, page 13
•Obtaining Technical Assistance, page 13
•Obtaining Additional Publications and Information, page 16
The Cisco 12404 Internet Router weighs 103 pounds (46.7 kg) fully configured
and 73 pounds (33.1 kg) without line cards. For lifting guidelines, see online
documentation Cisco 12404 Internet Router Installation and Configuration
Guide, Chapter 2, “Lifting Guidelines.”

Tools and Equipment
2
Cisco 12404 Internet Router Unpacking Instructions
78-13618-02
Tools and Equipment
You will need some of the following items and tools.
•3/16–inch flat-blade screwdriver
•1/4–inch flat-blade screwdriver
•9/16–inch (14-mm) wrench
•10–mm wrench (open-end or socket)
•ESD–preventive strap
•Tape—High performance, pressure sensitive, plastic, carton sealing tape
•Plastic banding
•Antistatic mat
•Wire cutters
•Pliers

3
Cisco 12404 Internet Router Unpacking Instructions
78-13618-02
Unpacking the Cisco 12404 Internet Router
Unpacking the Cisco 12404 Internet Router
This section explains how to unpack the router from the shipping pallet. Figure 1
shows the main packing material and accessory kit container.
Figure 1 Unpacking the Cisco 12404 Internet Router (Enhanced model
shown)
CONSOLIDA
TEDSWITCHF
ABRIC
CRITICAL
MAJOR
MINOR
MBUS
FAIL
ENABLE
ALARM FABRIC
1
02
3
40C48/POS-SR-SC
TX
RX
ACTIVE
CARRIER
RXPKT
CLASS1LASERPRODUCT
LASERPRODUKTDERKLASSE 1
PRODUITLASERDECLASSE1
PRODUCTOLASER DE CLASSE 1
CLEAN
CONNECTOR
WITHALCOHOL
WIPESBEFORE
CONNECTING
SLOT
-0
GIGABITROUTEPROCESSOR
SLOT
-1
COLL
LINK
TX
RX
RJ-45
MII
RESET
AUX
EJECT
CONSOLE
149546

Unpacking the Cisco 12404 Internet Router
4
Cisco 12404 Internet Router Unpacking Instructions
78-13618-02
After you have unpacked the router, check the contents of the shipping container
and verify that the following are included with your shipment.
•One Cisco 12404 Internet router, fully assembled
•Two AC power entry modules (PEMs) installed if ordered as an AC powered
unit
•Two DC power distribution units (PDUs) and two DC PEMs installed if
ordered as a DC powered unit
•One Accessories kit container
If you do not receive the items you ordered, contact your customer service
representative for assistance (see the “Obtaining Technical Assistance” section on
page 13 for additional information).
Use the following procedure to unpack the Cisco 12404 Internet router from the
shipping container.
Step 1 Use the wire cutters to cut the plastic bans that secure the corrugated shipping box
to the pallet.
Step 2 Remove the tape that seals the carton and open the top of the corrugated box.
Step 3 Use the handles on the accessory kit to remove it from the carton.
Step 4 Set aside the accessory kit.
Step 5 Remove the corner cushions and the plastic bag covering the router.
Step 6 Remove the master shipper and set it aside.

5
Cisco 12404 Internet Router Unpacking Instructions
78-13618-02
Unpacking the Cisco 12404 Internet Router
Step 7 Remove the bolts that secure the bracket to the back of the router (Figure 2).
Note Save the bolts and brackets. You will use them if you need to repackage
the router.
Figure 2 Cisco 12404 Internet Router Secured to Pallet (Rear View)
INPUT
OK
OUTPUT
FAIL
INPUT
100-240V
12A
50/80HZ
OUTPUT
OK
INPUT
OK
OUTPUT
FAIL
INPUT
100-240V
12A
50/80HZ
OUTPUT
OK
66401

Unpacking the Cisco 12404 Internet Router
6
Cisco 12404 Internet Router Unpacking Instructions
78-13618-02
Step 8 Remove the bolts that secure the brackets to the side of the router (Figure 3).
Note Save the bolt and brackets. You will use them if you need to repackage the
router.
Figure 3 Cisco 12404 Internet Router Secured to Pallet (Front View)
– If you are installing the enhanced version of the 12404 Internet router, go
to Step 9. For all other models, go to Step 11.
CONSOLIDA
TEDSWITCHF
ABRIC
CRITICAL
MAJOR
MINOR
MBUS
FAIL
ENABLE
ALARMFABRIC
1
023
40C48/POS-SR-SC
TX
RX
ACTIVE
CARRIER
RXPKT
CLASS1 LASER PRODUCT
LASERPRODUKTDERKLASSE1
PRODUITLASERDECLASSE1
PRODUCTOLASERDECLASSE1
CLEAN
CONNECTOR
WITHALCOHOL
WIPESBEFORE
CONNECTING
SLOT
-0
GIGABIT ROUTEPROCESSOR
SLOT
-1
COLL
LINK
TX
RX
RJ-45
MII
RESET
AUX
EJECT
CONSOLE
149561

7
Cisco 12404 Internet Router Unpacking Instructions
78-13618-02
Unpacking the Cisco 12404 Internet Router
Step 9 Cut the plastic tie-wrap and remove it from the upper left hinge bracket (Figure 4).
Note The plastic tie-wrap secures the front door to the chassis during shipment.
Figure 4 Removing the Tie-Wrap and Label
149690
REMOVE
TIE WRAP

Unpacking the Cisco 12404 Internet Router
8
Cisco 12404 Internet Router Unpacking Instructions
78-13618-02
Step 10 Open the front door and remove the labels (labeled REMOVE) that protect the
rubber bumpers during shipment (Figure 5).
– Close the front door.
Figure 5 Removing the Rubber Bumper Shipping Label
Step 11 Your Cisco 12404 Internet router is ready for installation. For installation
instructions, see the Cisco 12404 Internet Router Installation and Configuration
Guide online documentation, Chapter 3, “Installing the
Cisco 12404 Internet Router” part number 78-13511-xx.
REMOVE
149691

9
Cisco 12404 Internet Router Unpacking Instructions
78-13618-02
Repackaging the Cisco 12404 Internet Router
Repackaging the Cisco 12404 Internet Router
To repackage your Cisco 12404 Internet router for shipment, use these repacking
instructions. If packing material is lost or damaged, the
Cisco 12404 Internet router packing materials are available as an orderable item.
Use Product Number: GSR4-PKG=.
Tools and Equipment
You need the following items and tools.
•3/16–inch flat-blade screwdriver
•1/4–inch flat-blade screwdriver
•9/16–inch (14-mm) wrench
•10–mm wrench (open-end or socket)
•ESD-preventive strap
•Antistatic mat
•Wire cutters
•Pliers
•Bolts, screws, carton, and brackets removed when the chassis was unpacked

Repackaging the Cisco 12404 Internet Router
10
Cisco 12404 Internet Router Unpacking Instructions
78-13618-02
Repacking the Router
Repacking the Cisco 12404 Internet router into the shipping container is
presented in the following procedure. This procedure assumes you have
repackaged the accessory kit and have the bolts, screws, carton and brackets
removed when the chassis was unpacked.
Step 1 Place the router on a Cisco 12404 Internet router shipping pallet.
Step 2 Secure the side and rear brackets to the pallet with the bolts you saved when the
chassis was unpacked (see Figure 2 and Figure 3).
Step 3 Tighten all the captive screws on the power entry modules, power distribution
units, and line cards so that they are secure.
Step 4 Place the plastic bag cover over the router.
Step 5 Refer to Figure 1 and:
a. Place the front and rear foam cushions on top of the bagged router.
b. Place the accessory kit on top of the router.
c. Place the cardboard carton over the accessory kit and router.
Note If the master shipper tape closure was removed, replace it before you
secure the bands to your package.
Step 6 Secure the cardboard carton to the pallet with straps similar to the ones used to
ship the router to you.
Your Cisco 12404 Internet router is ready for shipment.