Cisco IR809 Operating and safety instructions

Product Overview
This chapter provides an overview of the features available for the Cisco 809 Integrated Services Routers
(ISRs).
For compliance and safety information, see Regulatory Compliance and Safety Information for Cisco 800
Series
Note
•General Description, on page 1
•SKU Information, on page 7
•Hardware Features, on page 8
•Supported Cisco Antennas and Cables, on page 9
•Power Supply, on page 16
•RJ45 Ports, on page 17
•Accessories, on page 18
General Description
The Cisco 809 Integrated Services Router (IR809), part of the Cisco Integrated Services Routers Generation
2 (ISR G2) Family, is designed as a next generation ruggedized fixed form factor router. It is a small-form
factor router with LTE, for use in ATM, POS, Telemetry, Billboards, Enterprise Fleet markets, Utilities and
other SCADA (Supervisory Control and Data Acquisition) environments.
The documentation set for this product strives to use bias-free language. For purposes of this documentation
set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial
identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be
present in the documentation due to language that is hardcoded in the user interfaces of the product software,
language used based on RFP documentation, or language that is used by a referenced third-party product.
Note
The following figure shows the IR809.
Product Overview
1

Figure 1: Cisco IR809 Integrated Services Router
The following figure shows the front panel details of the Cisco IR809.
Product Overview
2
Product Overview
General Description

Figure 2: Cisco IR809 Front Panel
Grounding Point8S0 RS232 DCE/RS485 Combo Port1
Mini type-B USB console/debug port9S1 RS232 DTE only2
SYS LED10GE0 (10/100/1000)3
Alarm LED11GE1 (10/100/1000)4
WAN/WWAN LEDs12USB 2.0 (Type-A Host Port)5
SIM Card LEDs13RESET Button6
DC Power/Alarm Connector7
LEDs are viewable from the top and from the front of the IR809.
Note
The following figure shows the back panel details of the Cisco IR809.
Product Overview
3
Product Overview
General Description

Figure 3: Cisco IR809 Back Panel
DIV TNC connector for 4G Modem1
SMA connector for GPS2
SIM0 and SIM1 Card Slots3
MAINTNCconnectorfor4GModem4
The following figure shows the top cover details of the Cisco IR809.
Product Overview
4
Product Overview
General Description

Figure 4: Cisco IR809 Top Cover
LEDs
The following table describes the LEDs for the Cisco 809 ISR.
Product Overview
5
Product Overview
LEDs

Table 1: LED Descriptions
DescriptionActivityLED
Innormaloperating mode, after system boots.(typicallyabout
2 minutes)
Off — No power
Green Steady on — Router is reachable, and all interfaces are up
and functioning properly
Green Flashing — Router is reachable, and no interface is in a
failed state
Amber Steady on — Router is unreachable (An external interface
of the router, that prevents the router from being remotely managed,
is in a critical failed state)
Amber Flashing — Router is reachable, but at least one of the
interfaces is in a non-critical failed state (functionality of that
interface is affected)
In bootup mode (during the first 60 seconds after powerup)
Green Steady on — Router is bootingy
Amber Steady on — Router has a system hardware failure
Power and System
Status
SYS
Off — Normal operation
Red - Alarm State on the Alarm Input
Alarm Input StatusALM
Off — No VPN tunnel
Steady Green — At least one VPN tunnel is up
VPNVPN_OK
Off — No link
Steady Green — Link is up
Flashing — Transmitting and Receiving data
Link StatusGE0
(10/100/1000)WAN
0
GE0
(10/100/1000)WAN
1
Off — GPS not configured
On — GPS configured
Slow Flash — GPS Acquiring in Standalone GPS
Fast Flash — GPS Acquiring in Assisted GPS
Slow Flash is defined as the LED will be on for 0.25
seconds and off for 0.75 seconds.Fast Flash is defined
as the LED will be on for 0.25 seconds and off for 0.25
seconds.
Note
GPS StatusGPS
Product Overview
6
Product Overview
LEDs

DescriptionActivityLED
Off — Modem not powered on On — Modem is powered on and
connected but not transmitting or receiving Slow Blink — Modem
is powered on and searching for connection
Fast Blink — Modem is transmitting or receiving.
Wireless WAN
Activity
WWAN
The RSSI LEDs are a 3 LED bar graph to indicate signal strength.
Their functionality is described in the RSSI LEDs table below.
Received Signal
Strength Indication
RSSI
Off — No USIM
Green — USIM installed and active
SIM cardsSIM0/SIM1
Table 2: RSSI LEDs
RSSI (0)RSSI (1)RSSI (2)RSSI
Green/AmberGreenGreen
OffOffOff< -110dBm
On - AmberOffOff-110 to
-90dBm
On - GreenOffOff-90 to -75dBm
On - GreenOn -
Green
Off-75 to -60dBm
On - GreenOn -
Green
On -
Green
> -60dBm
SKU Information
The following table lists the different SKUs available for the Cisco 809 Integrated Services Router. All SKUs
support external antenna.
Table 3: Supported SKUs for Cisco IR809s
DescriptionSKU ID
Multimode 4G/3G/2G connectivity to cellular networks operating in LTE 1900 MHz (band 2 PCS), 1700/2100
MHz (band 4 AWS), 850 MHz (band 5), 700 MHz (band 17) and 1900 MHz (band 25 extended PCS)
frequencies; backward-compatible with UMTS and HSPA+: 850 MHz (band 5), 900 MHz (band 8), 1900
MHz (band 2 PCS), and 1700/2100 MHz (band 4 AWS).
IR809G-LTE-NA-K9
Multimode 4G/3G/2G connectivity to cellular networks operating in LTE 700 MHz (band 13), 1700/2100
MHz (band 4 AWS), or 1900 MHz (band 25 extended PCS) frequencies; backward-compatible with EVDO
Rev A/CDMA 1x BC0, BC1, BC10.
IR809G-LTE-VZ-K9
Product Overview
7
Product Overview
SKU Information

DescriptionSKU ID
Multimode 4G/3G/2G connectivity to cellular networks operating in LTE 800 MHz (band 20), 900 MHz
(band 8), 1800 MHz (band 3), 2100 MHz (band 1), or 2600 MHz (band 7) frequencies; backward-compatible
with UMTS and HSPA+: 850 MHz (band 5), 900 MHz (band 8),1900 MHz (band 2), and 2100 MHz (band
1).
IR809G-LTE-GA-K9
Multimode 4G/3G connectivity to cellular networks operating in FDD LTE 2100 MHz (band 1), 1800 MHz
(band 3), 850 MHz (band 5), 2600 (band 7), 900 (band 8), 850 (band18, band19), 1500 (band 21), 700 (band
28)andTDD LTE 2600 (band 38), 1900 (band 39), 2300(band40)and2500(band41);backward-compatible
with WCDMA 2100 MHz (band 1), 850 MHz (band 5), 800 MHz (band 6, band 19), 900 MHz (band 8),
1700 MHz (band 9) and TD-SCDMA 1900 MHz (band 39).
IR809G-LTE-LA-K9
Memory
The Cisco IR809 uses flash memory and main memory. The flash memory contains the Cisco IOS software
image and the boot flash contains the ROMMON boot code. All memory components are factory default and
not upgradeable by the end user.
The following table shows the memory allocation.
Table 4: Cisco IR809 Memory
SpecificationMemory
2GBDefault and maximum DRAM
8 GB eMMC (4GB usable)Default and maximum flash memory
16MBBoot Flash
Hardware Features
This section provides an overview of hardware features for the Cisco 809 ISR.
Platform Features for Cisco IR809
The following lists the hardware platform features for the Cisco IR809.
• Mechanical/Environmental
• Form-factor, Width X Length X Height: 5.05" x 6.27" x 1.15" (12.8 x 15.9 x 2.9 cm)
• Mounting Options: Wall, floor, cabinet, shelf, and DIN Rail mounting
• -40C to +60C operating temperature (outside ambient)
• 5Kft altitude
• External Power Entry
• 9.6V to 60VDC; Nominal: 12 to 48VDC
Product Overview
8
Product Overview
Memory

• 4-pin 3.8 mm EURO power connector
• External Reset/Recovery Push Button
• WWAN Modem
• 1x internal Mini PCIe slot for Single multi-band 2G/3G/4G/LTE cellular modem
• Dual USIM Card slots (2 external SIM card slots). Provides Redundancy and multi-homing
capabilities over LTE and HSPA-based networks.
• WAN Ports
• 2x RJ45 10/100/1000 Gigabit Ethernet
• Serial Ports
• 1 x RJ45 RS232 DTE Port
• 1 x RJ45 RS232/RS485 DCE Port (SW-configurable)
• USB Ports
• 1x USB2.0 Type A External Host Port
• 1x USB2.0 Type Mini-B External Debug/Console Device Port
• Compliance
• Telcordia GR-3108 Class 2 deployment
• Class A EMC or better
• RoHS6
• IP30 compliant when vertical, IP40 compliant when mounted flat on a horizontal surface
Reset Button
The Reset button resets the router configuration to the default configuration set by the factory. To restore the
router configuration to the default configuration set by the factory, use a standard size #1 paper clip with wire
gauge 0.033 inch or smaller and simultaneously press the reset button while applying power to the router.
The reset button works in two different manners:
•With the reset button pressed for less than 10 seconds, the IR809 will load with saved start-up configuration
at that time.
• With the reset button pressed longer than 10 seconds, the NVRAM file system is erased and the IR809
boots up with Initial Configuration.
Supported Cisco Antennas and Cables
The Cisco IR809 ships without antennas. All antennas are options that can be ordered separately.
Product Overview
9
Product Overview
Supported Cisco Antennas and Cables

There are two TNC connectors on the backside of the device. The TNC connectors are used to connect to the
4G modem. The SMA connector is for the GPS antenna.
Before choosing your antenna type and installation scenario, read through the following information.
Note
This section lists the supported Antennas and Cables for the Cisco IR809. For detailed information about
Cisco Antennas, please refer to the following guides:
• Connected Grid Antennas Installation Guide:
http://www.cisco.com/c/en/us/td/docs/routers/connectedgrid/antennas/installing/cg_antenna_install_guide.html
• Antennas for the Cisco 800 Series Routers:
http://www.cisco.com/c/en/us/support/routers/800-series-routers/products-installation-guides-list.html
An antenna lighting arrestor must be used when an antenna is installed outdoors. Install per the country’s
national electrical code requirements for lightning protection. The Lightning Arrestor for LTE antenna’s is
CGR-LA-NF-NF or CGR-LA-NM-NF.
Note
The following antennas and cables are available:
ANT-3-4G2G1-O
Description: Cisco Quinta 3 element 3-in-1 transportation antenna
• 2x 4G cellular, 1xGPS
• Color: Black radome
• RoHS compliant
• Environment: Outdoor
ANT-4G-OMNI-OUT-N
Description: Cisco outdoor omnidirectional antenna for 2G, 3G, and 4G LTE cellular
• UV-stable radome
• Mast-mounting bracket
• Applicable for both 2G and 3G solutions
• Domestic LTE 700 band and global LTE 2600 band
• Domestic cellular and global GSM
• WiMAX 2300 and 2500
Electrical Specifications:
Product Overview
10
Product Overview
ANT-3-4G2G1-O