Cisco Linksys SGE2010P Manual

ADMIN GUIDE
BUSINESS SERIES
48-port 10/100/1000 Ethernet
Switch
Model: SGE2010/SGE2010P

SGE2010/SGE2010P Administration Guide i
Table of Contents
1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
What’s in this User Guide? 1
2Getting to Know the SGE2010/SGE2010P . . . . . . . . . . . . . . 2
SGE2010/P Front Panel 2
SGE2010/P Back Panel 3
3Connecting Devices to the SGE2010/SGE2010P . . . . . . . . . . . 4
Sample Network Configuration 4
Maximum Cabling Distances 4
Before You Install the Switch... 5
Placement Options 5
Desktop Placement 5
Rack-Mount Placement 6
Wall-Mount Placement 7
Connecting the Cables 7
4Using the Console . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting to Your Switch with HyperTerminal 9
Connecting to the Switch with Telnet 12
Logging On to the Console 12
Selecting Menu Options and Actions 12
Using the Switch Main Menu 13
System Configuration 13
System Information 14
Management Settings 16
Username & Password Settings 21
Security Settings 22
VLAN Management 25
IP Configuration 26
File Management 40
Restore System Default Settings 43
Reset to Factory Settings 43
Reboot System 43
Stack Configuration 44
Port Status 44

SGE2010/SGE2010P Administration Guide ii
Table of Contents
Port Status 45
PoE Status 45
Port Configuration 46
Port Settings 46
PoE Settings 47
System Mode (Layer 2 / Layer 3) Selection 48
Help 49
Logout 50
5Web Utility Configuration . . . . . . . . . . . . . . . . . . . . 51
Connecting to the Switch with the Web-Based Utility 51
Using Menus in the Web-Based Utility 51
Viewing On-line Help 52
AContacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
US/Canada Contacts 53
BCustomer Site Survey. . . . . . . . . . . . . . . . . . . . . . . 54
CWarranty Information . . . . . . . . . . . . . . . . . . . . . . 56
Limited Warranty 56
Exclusions and Limitations 56
Obtaining Warranty Service 57
Technical Support 57
DFederal Communication Commission Interference Statement . . 58
Industry Canada Statement 58
EC Declaration of Conformity (Europe) 58
ESpecifications . . . . . . . . . . . . . . . . . . . . . . . . . . 59

SGE2010/SGE2010P Administration Guide 1
What’s in this User Guide?
Introduction
1
Introduction
Welcome
Thank you for choosing a Linksys Switch. This Switch will allow you to quickly and economically
expand your Linksys system.
This new Linksys rack mount Switch delivers non-blocking, wire speed switching for your
network clients, plus multiple options for connecting to your network backbone. Forty eight
ports wire up your workstations or connect to other Linksys switches or devices.
The Switch features monitoring and configuration via your web browser, making it easy to
manage your Switch. Or if you prefer, you can use the console interface to configure the Switch.
Use the instructions in this guide to help you connect the switch, set it up, and configure it to
bridge your different networks. These instructions should be all you need to get the most out of
the Switch.
What’s in this User Guide?
This user guide covers the steps for setting up and using the Switch.
•Chapter 2, "Getting to Know the SGE2010/SGE2010P"
This chapter describes the ports, LEDs, and other features on the front and back panels of
the switch.
•Chapter 3, "Connecting Devices to the SGE2010/SGE2010P"
This chapter explains how to physically connect your network devices to the switch.
•Chapter 4, "Using the Console"
This chapter describes the use of the switch console, which allows you to perform basic
configuration of the switch.
•Chapter 5, "Web Utility Configuration "
This chapter provides an introduction to the features of the web-based configuration utility.
•Appendix A, "Contacts"
•Appendix B, "Customer Site Survey"
•Appendix C, "Warranty Information"
•Appendix D, "Federal Communication Commission Interference Statement"
•Appendix E, "Specifications"

SGE2010/SGE2010P Administration Guide 2
Getting to Know the SGE2010/SGE2010P
2
Getting to Know the SGE2010/SGE2010P
This chapter describes the ports, LEDs, and other features on the front and back panels of the
switch.
The SGE2010 and SGE2010P are 48-port, layer-2 Ethernet switches that affordably expand the
capability of the Linksys system. These two versions are functionally identical except the
SGE2010P model offers Power-over-Ethernet (PoE) which can be used to supply power to
various Linksys products over Ethernet cable.
SGE2010/P Front Panel
Feature Description
Reset The Switch can be reset by inserting a pin or paper clip into the RESET
opening.
CAUTION: If the RESET switch is pressed for more than 10 seconds, the
Switch will reset to its default settings. All customized user settings will be
lost.
LEDs The Switch uses Light Emitting Diodes (LEDs) to indicate the status of
numerous functions. These functions are listed below.
PWR A green PWR LED lights up to indicate that the Switch is powered on.
FAN A green FAN LED lights up to indicate that the cooling fan is operating
properly. A blinking red FAN LED indicates that the cooling fan has failed.
RPS A green RPS LED lights up to indicate that RPS is connected and operating
properly. A blinking red RPS LED indicates an RPS fault.
MST A green MST LED indicates that this Switch is a stack master.
Stack ID A green Stack ID LED indicates that this Switch is stacked and the
corresponding number indicates its stack ID.
Act/Link The green Act/Link LEDs light up to indicate a functional network link
through the corresponding port with an attached device. The Act
(Activity) LEDs flash to indicate that the Switch is actively sending or
receiving data over that port.
Speed On the SGE2010, a green Speed LED indicates that the port is linked to a
100Mbps device.
PoE On the SGE2010P, a green PoE LED indicates that PoE is active on that port.

SGE2010/SGE2010P Administration Guide 3
Getting to Know the SGE2010/SGE2010P
SGE2010/P Back Panel
1-48 The Switch is equipped with 48 auto-sensing, Ethernet (802.3) network
ports, which use RJ-45 connectors. The Fast Ethernet ports support
network speeds of 10Mbps, 100Mbps, or 1000Mbps. They can operate in
half and full-duplex modes. Auto-sensing technology enables each port to
automatically detect the speed of the device connected to it, and adjust
its speed and duplex accordingly.
The switch can deliver a maximum of 15.4W to a PoE port. With regular AC
power supply, there is 360W available to all PoE ports, and 280W available
with redundant power supply.
Ports 45, 46, 47 and 48 are shared with miniGBIC1, miniGBIC2, miniGBIC3,
and miniGBIC4, respectively.
NOTE: A switch is in stacking mode by default. In stacking mode, ports 24
and 48 are reserved for use as stacking ports. For more information
about stacking, refer to the SFE2010/SGE2010 Reference Guide.
miniGBIC1-4 The switch provides four mini-GBIC ports. The mini-GBIC (gigabit interface
converter) port is a connection point for a mini-GBIC expansion module,
so the Switch can be uplinked via fiber to another switch. Each mini-GBIC
port provides a link to a high-speed network segment or individual
workstation at speeds of up to 1000Mbps.
Use the Linksys MGBT1, MGBSX1, or MGBLH1 mini-GBIC modules with the
switch. The MGBSX1 and the MGBLH1 require fiber cabling with LC
connectors, while the MGBT1 requires a Category 5e Ethernet cable with
an RJ-45 connector.
NOTE: If shared ports are both connected, then the miniGBIC port has
priority.
Feature Description
Power The Power port is where you will connect the power cord.
Console The Console port is where you can connect a serial cable to a PC’s serial
port for configuration using your PC’s HyperTerminal program. Refer to
Chapter 4: Using the Console Interface for Configuration for more
information.
RPS Redundant Power Supply (Linksys RPS1000)
Feature Description

SGE2010/SGE2010P Administration Guide 4
Sample Network Configuration
Connecting Devices to the SGE2010/SGE2010P
3
Connecting Devices to the SGE2010/
SGE2010P
This chapter explains how to physically connect your network devices to the switch.
•”Sample Network Configuration,” on page 4
•”Maximum Cabling Distances,” on page 4
•”Before You Install the Switch... ,” on page 5
•”Placement Options,” on page 5
•”Connecting the Cables,” on page 7
Sample Network Configuration
For an example of a possible network configuration, see the application diagrams shown
below.
Maximum Cabling Distances
When you connect your network devices, make sure you don’t exceed the maximum cabling
distances, which are listed in the following table:
*A hub refers to any type of 100Mbps hub, including regular hubs and stackable hubs. A
10Mbps hub connected to another 10Mbps hub can span up to 100 meters (328 feet).
From To Maximum Distance
Switch Switch or Hub* 100 meters (328 feet)
Hub Hub 5 meters (16.4 feet)
Switch or Hub Computer 100 meters (328 feet)

SGE2010/SGE2010P Administration Guide 5
Before You Install the Switch...
Connecting Devices to the SGE2010/SGE2010P
Before You Install the Switch...
When you choose a location for the switch, observe the following guidelines:
• Make sure that the switch will be accessible and that the cables can be easily connected.
• Keep cabling away from sources of electrical noise, power lines, and fluorescent lighting
fixtures.
• Position the switch away from water and moisture sources.
• To ensure adequate air flow around the switch, be sure to provide a minimum clearance of
two inches (50 mm).
• Connect the supplied power cord to the switch’s power port, and plug the other end into an
electrical outlet.
CAUTION: Make sure you use the power cord that is supplied with the switch. Use of a
different power cord could damage the switch.
Placement Options
Before connecting cables to the Ethernet switch, first you will physically install the Ethernet
switch. Either set the Ethernet switch on its four rubber feet for desktop placement, mount it in
a standard-sized, 19-inch wide for rack-mount placement, or mount it on a wall with the wall-
mount brackets provided.
NOTE: The four supplied mounting brackets can be used for either wall mount or rack
mount installations.
Desktop Placement
1. Attach the rubber feet to the recessed areas on the bottom of the Ethernet switch.
2. Place the Ethernet switch on a desktop near an AC power source.

SGE2010/SGE2010P Administration Guide 6
Placement Options
Connecting Devices to the SGE2010/SGE2010P
CAUTION: Keep enough ventilation space for the Ethernet switch so it does not exceed the
environmental restrictions mentioned in the specifications.
Rack-Mount Placement
To mount the Ethernet switch in any standard-sized, 19-inch wide, (each Ethernet switch
requires 1RU of space in the rack), follow these instructions:
1. Remove the four front screws on one side of the Ethernet switch. Retain the screws for re-
installation.
2. Place one of the supplied spacers on the side of the Ethernet switch so the four holes align
to the screw holes.
3. Place a rack mount bracket next to the spacer and reinstall the four screws (removed in step
1).
4. Repeat steps 2 through 3 for the other side of the Ethernet switch.
5. Attach the Ethernet switch to the rack using the supplied screws.

SGE2010/SGE2010P Administration Guide 7
Connecting the Cables
Connecting Devices to the SGE2010/SGE2010P
Wall-Mount Placement
1. On one of the side corners, remove the four front screws on of the Ethernet switch. Retain
the screws for re-installation.
NOTE: The Ethernet switch, shown below, is mounted with the ports located on top. When
the switch is mounted to a wall, the ports can be oriented in any direction.
2. Place one of the supplied spacers on the side of the Ethernet switch so the four holes align
to the screw holes.
3. Place a rack mount bracket next to the spacer and reinstall the four screws (removed in step
1). The wall mount brackets should point towards the bottom of the Ethernet switch.
4. Repeat steps 1 through 3 for the other corners of the Ethernet switch.
5. Attach the Ethernet switch to a wall with appropriate screws (not supplied).
CAUTION: Ensure that the Ethernet switch is securely attached to the wall.
Connecting the Cables
To connect network devices to the Ethernet switch, follow these instructions:
1. For 10/100Mbps devices, connect a Category 5 Ethernet network cable to one of the
numbered ports on the Ethernet switch. For a 1000Mbps device, connect a Category 5e
Ethernet network cable to one of the uplink ports on the Ethernet switch.
NOTE: If connecting an Ethernet switch to an SVR3000 router, connect it to a Cascade port
on the SVR3000.
2. Connect the other end to a PC or other network device.
3. Repeat steps 2 and 3 to connect additional devices.
4. If you are using the mini-GBIC port, then insert the mini-GBIC module to the mini-GBIC port.
For detailed instructions, refer to the documentation supplied with the mini-GBIC module.