Cisco Small Business RV320 Instruction Manual

Cisco RV320/RV325 Gigabit Dual WAN VPN Router
ADMINISTRATION
GUIDE

78-20928-01

Cisco RV320/RV325 Administration Guide 3
Contents
Chapter 1: Getting Started 7
Features of the User Interface 8
Chapter 2: System Summary 11
System Information 11
Configuration (Wizard) 12
Port Activity 12
IPv4 and IPv6 13
Security Status 14
VPN Setting Status 14
SSL VPN Status 15
Log Setting Status 15
Chapter 3: Setup 17
Setup Network 17
IP Mode 17
WAN1 or WAN2 Port Settings 18
USB1 or USB2 Port Settings 28
3G/4G Connection 28
Setting Failover and Recovery 29
DMZ Enable 31
Password 31
Time 33
DMZ Host 34
(Port) Forwarding 34
Port Address Translation 37
Adding or Editing a Service Name 38
Setting Up One-to-One NAT 38
MAC Address Cloning 39
Assigning Dynamic DNS to a WAN Interface 40
Advanced Routing 41

Cisco RV320/RV325 Administration Guide 4
Contents
Configuring Dynamic Routing 41
Configuring Static Routing 42
Inbound Load Balance 43
USB Device Update 44
Chapter 4: DHCP 45
DHCP Setup 46
Viewing the DHCP Status 48
Option 82 49
IP and MAC Binding 49
DNS Local Database 51
Router Advertisement (IPv6) 52
Chapter 5: System Management 55
Dual WAN Connections 55
Bandwidth Management 57
SNMP 59
Configuring SNMP 59
Discovery-Bonjour 61
LLDP Properties 62
Using Diagnostics 62
Factory Default 63
Firmware Upgrade 63
Language Selection or Language Setup 64
Restart 65
Backup and Restore 65
Chapter 6: Port Management 69
Configuring the Ports 69
Port Status 70

Cisco RV320/RV325 Administration Guide 5
Contents
Traffic Statistics 70
VLAN Membership 71
QoS:CoS/DSCP Setting 71
DSCP Marking 72
802.1X Configuration 72
Chapter 7: Firewall 75
General 75
Access Rules 76
Content Filter 78
Chapter 8: VPN 81
Summary 81
Gateway to Gateway 83
Add a New Tunnel 83
Local Group Setup 84
Advanced Settings for IKE with Preshared Key and IKE with Certificate
89
Client to Gateway 91
Advanced Settings for IKE with Preshared Key and IKE with Certificate
98
VPN Passthrough 100
PPTP Server 100
Chapter 9: Certificate Management 101
My Certificate 101
Trusted SSL Certificate 103
Trusted IPsec Certificate 103
Certificate Generator 104
CSR Authorization 105

Cisco RV320/RV325 Administration Guide 6
Contents
Chapter 10: Log 107
System Log 107
System Statistics 110
Processes 110
Chapter 11: SSL VPN 111
Status 112
Group Management 112
Resource Management 115
Advanced Setting 116
Chapter 12: Wizard 117
Chapter 13: User Management 119

1
Cisco RV320/RV325 Administration Guide 7
Getting Started
The default settings are sufficient for many small businesses. Network demands
or your Internet Service Provider (ISP) might require modification of the settings.
To use the web interface, you need a PC with Internet Explorer (version 6 and
higher), Firefox, or Safari (for Mac).
To launch the web interface:
STEP 1 Connect a PC to a numbered LAN port on the device. If the PC is configured to
become a DHCP client, an IP address in the 192.168.1.x range is assigned to the
PC.
STEP 2 Start a web browser.
STEP 3 In the address bar, enter the default IP address of the device, 192.168.1.1. The
browser might issue a warning that the web site is untrusted. Continue to the web
site.
STEP 4 When the login page appears, enter the default user name cisco and the default
password cisco (lowercase).
STEP 5 Click Login. The System Summary page appears. Check the Port Activity to see
if a WAN connection is enabled. If not, continue to the next step.
STEP 6 To use the setup wizard to configure your Internet connection, click Setup Wizard
on the System Summary page. Or click Wizard in the navigation tree and in the
Basic Setup section, click Launch Now. Follow the on-screen instructions.
If your web browser displays a warning message about the pop-up window, allow
the blocked content.
STEP 7 To configure other settings, use the links in the navigation tree.

Getting Started
Features of the User Interface
8 Cisco RV320/RV325 Administration Guide
1
Troubleshooting Tips
If you have trouble connecting to the Internet or the web-based web interface:
•Verify that your web browser is not set to Work Offline.
•Check the local area network connection settings for your Ethernet adapter.
The PC should obtain an IP address through DHCP. Alternatively, the PC can
have a static IP address in the 192.168.1.x range with the default gateway
set to 192.168.1.1 (the default IP address of the device).
•Verify that you entered the correct settings in the Wizard to set up your
Internet connection.
•Reset the modem and the device by powering off both devices. Next,
power on the modem and let it sit idle for about 2 minutes. Then power on
the device. You should now receive a WAN IP address.
•If you have a DSL modem, ask your ISP to put the DSL modem into bridge
mode.
Features of the User Interface
The user interface is designed to make it easy for you to set up and manage your
device.
Navigation
The major modules of the web interface are represented by buttons in the left
navigation pane. Click a button to view more options. Click an option to open a
page.
Pop-Up Windows
Some links and buttons launch pop-up windows that display more information or
related configuration pages. If your web browser displays a warning message
about the pop-up window, allow the blocked content.
Help
To view information about the selected configuration page, click Help near the top
right corner of the web interface. If your web browser displays a warning
message about the pop-up window, allow the blocked content.

Getting Started
Features of the User Interface
Cisco RV320/RV325 Administration Guide 9
1
Logout
To exit the web interface, click Logout near the top right corner of the web
interface. The Login page appears.

Getting Started
Features of the User Interface
10 Cisco RV320/RV325 Administration Guide
1