Cisco vEdge Series Manual

Hardware Installation Guide for vEdge Routers
First Published: 2018-03-27
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

©Cisco Systems, Inc. All rights reserved.

CONTENTS
vEdge 100 Router 1
CHAPTER 1
Declaration of Conformity 2
Components and Specifications 2
Front and Rear Panel Components 4
Ports and Connectors 6
Power Supply and Cooling System 7
General Safety Standards 8
Site Preparation Guidelines 9
Install the vEdge 100 Router 10
Connect the vEdge 100 Router 16
vEdge 100 Router Default Configuration 19
Maintenance and Troubleshooting 20
Restore a vEdge Router 22
Return Hardware 23
vEdge 100b Router 27
CHAPTER 2
Declaration of Conformity 28
Components and Specifications 29
Front and Rear Panel Components 31
Ports and Connectors 33
Power Supply 33
Planning and Installation 34
Prepare for Router Installation 35
Install the vEdge 100b Router 36
Connect the vEdge 100b Router 40
vEdge 100b Router Default Configuration 43
Hardware Installation Guide for vEdge Routers
iii

Maintenance and Troubleshooting 46
Restore a vEdge Router 47
Return Hardware 48
vEdge 100m Router 51
CHAPTER 3
At a Glance 52
Declaration of Conformity 52
Components and Specifications 53
Components and Specifications 53
Front and Rear Panel Components 57
Ports and Connectors 60
Power Supply and Cooling in a Cisco vEdge 100m Router 61
Planning and Installation 61
Planning and Installation 61
Prepare for Router Installation 62
Install the vEdge 100m Router 63
Connect the vEdge 100m Router 69
vEdge 100m Router Default Configuration 72
Maintenance and Troubleshooting 77
Maintenance and Troubleshooting 77
Restore a vEdge Router 78
Return Hardware 79
vEdge 100wm Router 83
CHAPTER 4
Declaration of Conformity 84
Components and Specifications 85
Front and Rear Panel Components 89
Ports and Connectors 92
Power Supply and Cooling System 93
Planning and Installation 93
Prepare for Router Installation 94
Install the vEdge 100wm Router 95
Connect the vEdge 100wm Router 102
Maintenance and Troubleshooting 105
Hardware Installation Guide for vEdge Routers
iv
Contents

Restore a vEdge Router 107
Return Hardware 108
vEdge 1000 Router 111
CHAPTER 5
Declaration of Conformity 112
Components and Specifications 113
Front Panel Components 115
Supported Transceivers 117
Ports and Connectors 120
Power Supply and Cooling in Cisco vEdge 1000 Routers 126
Field-Replaceable Units 128
USB Dongle for Cellular Connection 128
Planning and Installation 130
Prepare for Router Installation 131
Install the vEdge 1000 Router 132
Connect the vEdge 1000 Router 144
vEdge 1000 Router Default Configuration 149
Maintenance and Troubleshooting 150
Install a Transceiver 152
Remove a Transceiver 153
Restore a vEdge Router 154
Return Hardware 155
vEdge 2000 Router 159
CHAPTER 6
Declaration of Conformity 160
Components and Specifications 161
Front Panel Components 163
PIM and Transceiver Modules 165
Supported Transceivers 171
Ports and Connectors 173
Field-Replaceable Units 180
Power Supply and Cooling in Cisco vEdge 2000 Routers 181
Planning and Installation 183
Prepare for Router Installation 184
Hardware Installation Guide for vEdge Routers
v
Contents

Install the vEdge 2000 Router 185
Connect the vEdge 2000 Router 194
Install vEdge 2000 Router Components 198
vEdge 2000 Router Default Configuration 202
Maintenance and Troubleshooting 203
Remove vEdge 2000 Router Components 205
Restore a vEdge Router 209
Return Hardware 210
vEdge 5000 Router 213
CHAPTER 7
Declaration of Conformity 214
Components and Specifications 215
Front and Rear Panel Components 217
NIM and Transceiver Modules 220
Supported Transceivers 225
Ports and Connectors 227
Field-Replaceable Units 234
Power Supply and Cooling in Cisco vEdge 5000 Routers 234
Planning and Installation 237
Prepare for Router Installation 238
Connect the vEdge 5000 Router 239
vEdge 5000 Router Default Configuration 241
Maintenance and Troubleshooting 243
Remove vEdge 5000 Router Components 244
Restore a vEdge Router 248
Return Hardware 249
vEdge Cloud Router 253
CHAPTER 8
Declaration of Conformity 254
Hardware Installation Guide for vEdge Routers
vi
Contents

CHAPTER 1
vEdge 100 Router
The vEdge 100 router delivers highly secure site-to-site data connectivity to small business and home offices
(SOHO). The vEdge 100 router is a fixed-port-configuration router with the following features:
• Five built-in 10/100/1000 Mbps Ethernet ports
• Power over Ethernet (PoE) source support on one Ethernet port
• Encryption and QoS support
• 100 Mbps forwarding throughput (inclusive of encryption)
• Secure identification chip for anti-counterfeit and secure authentication
• Integrated power supply
• Kensington security lock slot to physically lock down the router
• GPS input for geographical location
• Desktop mount, wall mount, or rack-mountable in a 19-inch rack
Chassis Views
Figure 1 and Figure 2 show the front and back panels of the vEdge 100 router, indicating the location of the
power interfaces, status indicators, and chassis identification labels.
Figure 1: Front Panel of the vEdge 100 Router
Figure 2: Back Panel of the vEdge 100 Router
Hardware Installation Guide for vEdge Routers
1

•Declaration of Conformity, on page 2
•Components and Specifications, on page 2
•General Safety Standards, on page 8
•Maintenance and Troubleshooting, on page 20
Declaration of Conformity
The Viptela products are controlled under the Commerce Control List (CCL) of the U.S. Export Administration
Regulations (EAR) as networking equipment within the following U.S. Export Control Classification Numbers
(ECCN): 5A002, 5D002, and 5E002.
The vEdge hardware and software products and the Viptela encryption technology can be delivered to most
end users and destinations worldwide without a licensing requirement. The Viptela solution and products
have undergone a one-time review by the Government of the United States of America and qualify for License
Exception ENC. As such, they are eligible for export according to Section 740.17 of the EAR.
The Viptela solutions and products can be delivered to most end users worldwide, except to entities or end
users in the following countries: Cuba, Iran, North Korea, Sudan, and Syria.
Controlled Technologies
Viptela manages technology subject to the U.S. Export Administration Regulations (EAR). These controlled
technologies may include items under U.S. ECCN 5E002 encryption technology. The Viptela encryption
technology is for the development, production, and use of Viptela products that implement or use encryption.
The Viptela software distribution policy allows only authenticated users to download the Viptela encryption
software. Recipients of controlled technology are obliged to maintain adequate controls to prevent nationals
from outside the U.S. and Canada from accessing Viptela information, subject to ECCN5E002, without first
obtaining authorization from the U.S. government.
For additional information on controlled technologies, please contact Viptela support at [email protected]
.
Components and Specifications
This article provides the chassis specifications of the vEdge 100 router and lists the other router components.
Hardware Installation Guide for vEdge Routers
2
vEdge 100 Router
Declaration of Conformity

Chassis Specifications
Table 1 lists the specifications for the vEdge 100 router chassis.
Table 1:
SpecificationItem
Services and Slot Density
5 ports, one of which has 802.3af PoE source
capability
RJ45 Ports 10/100/1000 Mbps
YesEmbedded hardware-based crypto acceleration (IPSec)
2 GBMemory DDR3 ECC DRAM
4 GBNAND storage (internal)
1USB host port (Type A USB 3.0)
1Mini USB connector console port (default baud
rate 115.2 Kbps)
AC Input (C6 inlet connector)Power supply
Power Specifications
90-264 Vrms
AC input voltage
47-63 HzAC input line frequency
15 WattsTypical power consumption with PoE disabled on ge0/0
32 Watts maximumTypical power consumption with PoE enabled on ge0/0
Physical Specifications
1.5 in. (3.8 cm)
Chassis height
9 in. (22.9 cm)Chassis width
5.5 in. (14 cm)Chassis depth
Can be accommodated in 1 RURack height
3.1 lb (1.4 kg)Chassis weight
Provided with the unitRack-mount accessory kit 19 in (48.3 cm) EIA
Packaging Specifications
2.5 in. (6.4 cm)
Package height
12.4 in. (31.6 cm)Package width
9.6 in. (24.4 cm)Package depth
Hardware Installation Guide for vEdge Routers
3
vEdge 100 Router
Components and Specifications

SpecificationItem
Operating Condition
0 to 40°C (32 to 104°F) at sea level ( temperature
de-rating of 1.5 deg C per 1000 feet of altitude
applicable up to max of 10000 feet or 3000 m)
Temperature
Max 3000 m (10000 ft)Altitude
10 to 85% RHHumidity
Transportation/Storage Condition
-40 to 70°C (-40 to 158°F)
Temperature
5 to 95%RHHumidity
4570 m (15000 ft)Altitude
Reliability
104K hours
MTBF
Regulatory Compliance
AS/NZS 60950-1 CAN/CSA 60950-1
CB-IEC60950-1 CE Marking EN 60950-1
UL60950-1
Safety
AS/NZS CISPR22 Class A EN 300 386 EN 55022
Class A FCC Class A ICES Class A VCCI Class A
EMC
ROHS 6/6Environmental
Front and Rear Panel Components
This article describes the components on the front and rear panels of the vEdge 100 router. See At a Glance
for the exact location of these components on the router.
Front Panel LEDs
The vEdge 100 router has five chassis status LEDs located in the front. See Figure 1.
Figure 1: Chassis Status LEDs in a vEdge 100 Router
Hardware Installation Guide for vEdge Routers
4
vEdge 100 Router
Front and Rear Panel Components